IDEC HW Series Catalog Page
ø22 HW |
Key Locking Safety Switches |
|
|
<![endif]>Overview
<![if ! IE]><![endif]>XW Series E-Stops
<![if ! IE]><![endif]>Interlock Switches
<![if ! IE]><![endif]>Safety Control Relays Enabling Switches
<![if ! IE]><![endif]>AS-Interface Safety at Work Light Curtains
ø22 HW Key Switch
Key features:
•Key Selector Switches with Direct Opening Action Mechanism
•High-security Pin Tumbler Key
•The NC contact is opened by direct opening action mechanism 
. Mode selection enables easy construction of safety systems.
•The single key enables the hostage control of combining HW series key selector switch (pin tumbler type) and HS5E-K interlock key switch. High-security pin tumbler key is used. Sixteen types of key numbers are available.
•Selection of 2-position and 3-position, maintained, spring-return types and key retained variety is available.
•Degree of Protection: IP65 (IEC60529)
Applicable Standards |
Mark |
File No. or Organization |
|
UL508 |
|
|
UL Listing |
|
|
File No. E68961 |
|
|
|
|
|
|
|
|
|
|
|
|
|
CSA C22.2 No.14 |
|
|
CSA166730 (LR92374) |
TÜV Rheinland R50054316
EN60947-5-1
Self-declaration
Low Voltage Directive of Europe
Two-position Key Switch (90°)
|
|
|
|
Standard Logic |
|
|
Inverse Logic |
|
|
|||
Contact |
Contact Block |
Logic Table |
Maintained |
Logic Table |
Maintained |
|
||||||
Mounting |
|
|
|
1 |
2 |
|
|
2 |
1 |
|
||
Code |
Contact |
1 |
2 |
|
|
1 |
2 |
|
|
|
||
Position |
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
||
1NO |
|
NO |
|
|
HW1K-2PA10 |
|
|
HW1K-2JPA10 |
|
|||
(10) |
|
– |
Dummy Block |
Dummy Block |
|
|||||||
|
|
|
|
|
||||||||
1NC |
|
NC |
|
|
|
|
|
|
|
Contact Block Mounting Position |
||
|
HW1K-2PA01 |
|
HW1K-2JPA01 |
|
||||||||
(01) |
|
– |
Dummy Block |
Dummy Block |
|
|||||||
|
|
|
|
|||||||||
2NO |
|
NO |
|
|
|
|
|
|
|
|
|
|
|
HW1K-2PA20 |
|
HW1K-2JPA20 |
|
||||||||
(20) |
|
NO |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
||||||
2NC |
|
NC |
|
|
HW1K-2PA02 |
|
|
HW1K-2JPA02 |
|
|||
(02) |
|
NC |
|
|
|
|
|
|||||
|
|
|
|
|
|
|||||||
1NO-1NC |
|
NO |
|
|
HW1K-2PA11 |
|
|
HW1K-2JPA11 |
|
|||
(11) |
|
NC |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
||||||
|
|
NO |
|
|
|
|
|
|
|
|
|
|
2NO-2NC |
|
NC |
|
|
HW1K-2PA22 |
|
|
HW1K-2JPA22 |
|
|||
(22) |
|
NO |
|
|
|
|
|
|||||
|
|
|
|
|
|
|
||||||
|
|
NC |
|
|
|
|
|
|
|
|
|
|
For contact block mounting position, see the figure to the right of the table.
Each key selector switch is supplied with two keys.
Key number 500 is supplied as the default key in table above (500 not added to part number).
To order additional key types, specify key number at end of part number (special order).
Example: HS5E-KVA003-2A501
|
501 to 515
Note: The key number is engraved on the cylinder.
346 |
www.IDEC.com |
1602261620 |
|
|
Loading...