Page 1
SecuriTEST ® IP
Page 2
SecuriTEST® IP User Manual
COPYRIGHT NOTICE
The information contained in this document is the property of IDEAL INDUSTRIES Ltd.
and is supplied without liability for errors and omissions. No part of this document may
be reproduced or used except as authorized by contract or other written permission
from IDEAL INDUSTRIES Ltd. The copyright and all restrictions on reproduction and
use apply to all media in which this information may be placed.
IDEAL INDUSTRIES Ltd. pursues a policy of continual product improvement and
reserves the right to alter without notice the specification, design, price or conditions
of supply of any product or service.
© IDEAL INDUSTRIES LTD. 2018
All rights reserved
Publication ref: 171810
Issue 1 - 4/18
IDEAL INDUSTRIES LTD.
Stokenchurch House
Oxford Road
Stokenchurch
High Wycombe
Buckinghamshire
HP14 3SX UK
www.idealnetworks.net
Page 3
SecuriTEST® IP User Manual
GENERAL
INTERFACE AND STATUS INDICATION
SETTINGS
POWER
Introduction
Page 1
Safety
Page 2
Battery
Page 2
Keypad
Page 3
Electrical
Interface
Page 4
Wi-Fi
Interface
Page 5
LED
Indicators
Page 6
Screen
Functions
Page 7
IP Settings
Page 8
Wi-Fi Setup
Page 9
Shortcut
Menu
Page 10
FTP Server
Page 11
Storage
(SD Card)
Page 12
HDMI OUT
Page 13
Remote
View
Page 14
System
Page 15
PoE Output
Page 16
DC 12v Output
Page 17
PoE and
Power Info
Page18
Page 4
SecuriTEST® IP User Manual
IP CAMERA TEST
HD COAX AND ANALOG CAMERA TEST
CABLE TESTING
IP Camera
Test Flow
Page 19
Direct Camera
Page 20
Network
Camera
Page 21
IP Discovery
Page 20
ONVIF
Page 21
PTZ
Page 22
Chrome
Page 23
Non ONVIF Test
Page 24
CVBS
Page 25
PTZ Address
Scanning
Page 27
Video Out
Page 28
TVI
Page 29
CVI
Page 30
AHD
Page 31
PTZ
Page 26
Cable Test
Page 32
RJ45 Cable
TDR
Page 33
Tone
Generator
Page 34
Page 5
SecuriTEST® IP User Manual
IP NETWORK TEST
RESULTS AND TRANSFER
MY APPS
SOFTWARE UPDATE
Ping
Page 35
IP Scan
Page 36
DHCP Server
Page 37
Available IP
Page 38
Network
IP Scan
Page 39
Data Monitor
(RS485)
Page 40
Test Report
Page 41
Jobs
Page 42
File
Explorer
Page 43
File
Transfer
Page 44
Rapid Video
Page 44
HIKVISION
Page 46
DAHUA
Page 47
RTSP Player
Page 48
Local
Update
Page 49
Page 6
SecuriTEST® IP User Manual
TOOLS
TECHNICAL SPECIFICATION
Notepad
Page 50
Interfaces
Page 51
Camera Test
Functions
Page 52
Electrical Test
Functions
Page 53
General Test
Functions
Page 54
Results,
Upgrade and
Help
Page 55
General
Page 56
Page 7
171810.01 SecuriTEST® IP 1
SecuriTEST® IP User Manual
GENERAL - Introduction
Page 8
171810.01 SecuriTEST® IP 2
SecuriTEST® IP User Manual
GENERAL - Safety
Exercise caution when handling rechargeable batteries.
All lithium-polymer battery packs, regardless of their indicated charge state, are
capable of producing electrical current sufficient to cause personal injury and/or
property damage.
GENERAL - Battery Handling
Do not dispose of battery packs in a fire or with regular waste. Battery packs may
explode if exposed to open flame. The battery packs are hazardous waste and may
contaminate ground water sources if disposed of in landfills.
The following battery pack handling precautions must be closely followed to avoid risk
of injury.
• When a battery pack is not installed in the tester, it should be kept in a clean, dry,
non-conductive package.
• Keep conductive materials away from the battery pack at all times.
• Keep contact sides of the battery pack away from each other at all times.
• Battery packs can only be charged while in the tester. Charging in any other
manner may cause the battery pack to explode.
• Always install, remove, store, and charge the battery packs in a non-explosive
atmosphere.
• Observe operating and storage temperatures (see Technical Specifications
section).
• Do not allow children or persons unfamiliar with the precautionary instructions in
this manual to handle or recharge the battery packs.
• Use only the charger supplied.
To remove the battery:
To replace the battery, reverse the above procedure.
1. Remove boot
3. Remove battery
2. Remove cover
Page 9
171810.01 SecuriTEST® IP 3
SecuriTEST® IP User Manual
INTERFACE AND STATUS INDICATION - Keypad
Long press to switch
the tester ON/OFF.
Home screen /
shortcut menu
Zoom in
Aperture open /
increase / confirm
Menu navigation
/ PTZ controls
Confirm settings and
return.
Long press to
capture
a screen
shot.
While the screen shot
is being created, a
smaller version of the
screen appears briefly,
then the screen shot is
stored in the Jobs /
Screenshots folder of
the internal SD card.
Short press to
sleep / wake
Digital zoom
toggle
Focus near
Aperture close / decrease
/ exit in
-camera menu
Return without confirming
settings. Long press to
return to home screen
Zoom out
Focus far
Page 10
171810.01 SecuriTEST® IP 4
SecuriTEST® IP User Manual
INTERFACE AND STATUS INDICATION - Electrical Interface
RS485 PTZ interface
HDMI input for NVR/DVR
checking (replacing display)
Video OUT / Coax tone generator
Coax video IN for analog, HD TVI/CVI/AHD
Direct connect to IP camera or LAN for access cameras
on the network. Selectable PoE output.
Passes network PoE or PoE injector PoE to camera does not pass data
Top panel connectors and indicators
LED flashlight
12 Volt / 2 Amp DC output to power non-PoE cameras
Bottom panel connectors and indicators
MicroSD card slot (push inwards to eject)
UTP cable test port
USB 5V 2A charging port - no data connection
Audio IN and OUT
12 Volt 2 Amp power adapter input
HDMI output for monitor testing
Battery isolation / storage switch. Set the isolating switch to the I
position to use
or charge the tester. Set to O position to isolate the
battery for long term storage and to
prevent the tester from being
swit
ched on accidentally when not in use. The battery can not be
charged in the
O position but the tester can be switched on if the
external supply is connected. The charge LED flashes when the
external supply is connected in the
O position.
Page 11
171810.01 SecuriTEST® IP 5
SecuriTEST® IP User Manual
INTERFACE AND STATUS INDICATION - Wi-Fi Interface
A 2.4G 802.11n Wi-Fi port is provided inside the tester. It can be used for:
• Connecting to Wi-Fi networks to access IP cameras for testing
• Connecting to Wi-Fi networks for file transfer via Internet or FTP
When the tester is connected to a Wi-Fi network, the Wi-Fi icon is displayed on top
right hand corner of the screen.
SETUP >> Wi-Fi
Tap to switch Wi-Fi on
Page 12
171810.01 SecuriTEST® IP 6
SecuriTEST® IP User Manual
INTERFACE AND STATUS INDICATION - LED Indicators
Power adapter connected
RS485 data receiving
RS485 data transmitting
LEDs lit together indicate sleep
mode (screen blanked)
Charging status:
lit=charging
off=
fully charged
flashing = external supply is connected while the
isolating switch is in the
O position (battery can not
be charged in this state)
or battery not fitted.
The charging status is also indicated
by the
icon at
the top right of
the screen
Page 13
171810.01 SecuriTEST® IP 7
SecuriTEST® IP User Manual
INTERFACE AND STATUS INDICATION - Screen Functions
Status indications
Quick Access Menu
Shortcut Menu
Icon re-arrangement
(
Camera/Network port link status
MicroSD card status
Date (yyyy-mm-dd)
Battery status
Time (hh:mm:ss in 24
hour format)
Drag down from the top right hand corner of the
screen to reveal the Quick Access Menu. This
provides quick access to a selection of commonly
used tester functions. (Note that this selection is
not user
-configurable.)
Press the
key to reveal the Shortcut Menu.
This provides shortcuts to up to 8 tester
functions, configurable under SETUP >> Shortcut
Menu.
Tap any of the Main Menu icons to display the
relevant menu
. Touch and hold any menu icon to
drag it into a new po
sition in the same menu.
Tap the
icon to turn it orange. Then touch
and hold a
ny menu icon to drag it and release in
the desired different menu folder.
(Note that a Factory Reset will restore all icons to
their standard positions, but any software updat
e
performed since the tester was manufactured will
need to be re
-installed following Factory Reset.)
Page 14
171810.01 SecuriTEST® IP 8
SecuriTEST® IP User Manual
SETTINGS - IP Settings
SETUP>>IP Settings
Tick RJ45 to enable
the LAN socket and
switch off Wi-
Fi
Tap to configure the
DHCP server
Select Static IP or
Dynamic IP (DHCP)
Edit static addresses
or display network
-
assigned Dynamic IP
addresses
PPPoE is used for authentication
of the network access with
known user name and password.
Enables preset IP addresses to be entered
for future use. The IP address could be in a
different subnet.
OK applies the new settings only if they
are valid
DHCP server status on/off
Page 15
171810.01 SecuriTEST® IP 9
SecuriTEST® IP User Manual
SETTINGS - Wi-Fi Setup
SETUP>>Wi-Fi
Tap to switch Wi-Fi
on/off
Tap a connected network to display
its details and to remove it from the
list:
Touch and hold to enter the IP
address details of the Wi
-Fi router:
Tap an available network to enter its password
and to connect to it:
Tap to enter network details manually:
Page 16
171810.01 SecuriTEST® IP 10
SecuriTEST® IP User Manual
SETTINGS - Shortcut Menu
SETUP>>Shortcut menu
Touch and hold an application icon to move it
automatically to the Shortcut menu. (Up to 8 icons
can be moved to the Shortcut Menu
Touch and hold an
application to move
it back automatically
to the main
applications list
Press the
key to reveal the Shortcut Menu or to return from the open App.
Page 17
171810.01 SecuriTEST® IP 11
SecuriTEST® IP User Manual
SETTINGS - FTP Server
The FTP server can be used to transfer files to and from the tester via network
interface.
SETUP>>FTP Server
Copy the tester’s ftp
address to the browser in
the PC
Wi-Fi or wired
network
Tap “Start FTP Server”
Select “Anonymous server login“
(no password required)
Browse the tester’s internal
or external SD card file
system, as set in the FTP
tab in File Explorer
Page 18
171810.01 SecuriTEST® IP 12
SecuriTEST® IP User Manual
SETTINGS - Storage (SD Card)
SETUP>>Storage
Displays the Total, Used and Available
capacity of the internal storage
Page 19
171810.01 SecuriTEST® IP 13
SecuriTEST® IP User Manual
SETTINGS - HDMI Out
SETUP>>HDMI Out
Used for testing monitors and projectors and for training. The tester’s screen (static or
video) is mirrored to the HDMI Output port.
Tap to switch the HDMI output on/off
(default is ON)
Select the required
HDMI resolution /
format
Page 20
171810.01 SecuriTEST® IP 14
SecuriTEST® IP User Manual
SETTINGS - Remote View
SETUP>>Remote View
Use Remote View to stream video from the tester’s screen to the LAN / Wi-Fi port. Use
an RTSP player (VLC recommended) to view the video on a PC or smart device
connected to the tester via a network.
Tap to start the Remote View
Select the required
Remote View
resolution / format
Wi-Fi or wired
network
Copy the URL from the tester screen
to the VLC settings (Network >>
Address) in the PC (or capture the QR
code on a smart device)
Page 21
171810.01 SecuriTEST® IP 15
SecuriTEST® IP User Manual
SETTINGS - System
The System settings are grouped under the heading of System.
Tap to expand the System group.
Tap to return to the top level Setup menu
SETUP>>System>>Date & Time
SETUP>>System>>Factory Reset
Tap then confirm to restore the tester configuration to the original
factory settings.
CAUTION! Any software updates performed since the tester was manufactured will
need to be re-installed following Factory Reset. (Note that the user software can not
be backed up. For standard software, the user needs to download latest SW from
IDEAL Networks web site to recover it. The user’s own software needs to be reinstalled
separately.
Tick to synchronise with local time
Set Date and Time
(when Auto is un
-
ticked)
Tap to select local time zone
Tap to apply the new
settings (when Auto
is un
-ticked)
Page 22
171810.01 SecuriTEST® IP 16
SecuriTEST® IP User Manual
POWER - PoE Output
The tester's LAN port is equipped with Power over Ethernet capability. It can be used
to provide power to PoE enabled cameras:
POWER >> PoE
PoE Camera
Power + Data
Tap the switch to turn PoE on/off
Floating indicator shows PoE
status, voltage and power
consumed. This floating
PoE
indicator can be dragged to any
convenient place on the screen,
and always appears on top.
Double-
tap the floating indicator
to display / hide more details:
Indicates that PoE is
present on the
LAN/Network port
Indicates the pin
numbers of the
actual PoE voltages
applied
Indicates the PoE
power consumed
by the load
Page 23
171810.01 SecuriTEST® IP 17
SecuriTEST® IP User Manual
POWER - DC 12V Output
The 12 volt DC socket on the top panel of the tester can supply up to 2 amps to non-
PoE cameras.
Note that the power is always present on the socket, regardless of the setting of the
PoE switch.
TOOLS >> PoE & Power Info
Non-PoE
Camera
Power
Indicates the output
voltage
Indicates the output
power
Page 24
171810.01 SecuriTEST® IP 18
SecuriTEST® IP User Manual
POWER - PoE and Power Info
TOOLS >> PoE & Power Info
(Note – when this screen is displayed, the PoE output is switched off if the tester is
running on battery power. At the same time the PoE Input power and data will be
passing through to the LAN/Network port.)
Indicates PoE input status
Use the 12 v input for testing
camer
a power supplies
Indicates the pin numbers
of the PoE
input voltages.
The
PSE voltage will pass
through to LAN/Network
port while data will not
pass through.
Indicates the power
consumed by the
load or provided by
the camera or PoE
supply
Indicates the PoE / DC
voltages present
Page 25
171810.01 SecuriTEST® IP 19
SecuriTEST® IP User Manual
IP CAMERA TEST - IP Camera Test Flow
A typical test sequence consists of providing power to the camera,
connecting to it and accessing its controls, setting it up and creating a
report to record its correct operation:
1. POWER
Provide power to the camera and allow time to boot up.
2. IP SET
Use IP Discovery to find the IP address of a single camera or use
NETWORK CAMERA or ONVIF to find the IP address of a network
connected camera.
3. ACCESS
User name or password may be needed to access the camera.
4. SETUP
Setup camera parameters such as name, IP address, video format etc via
ONVIF and web browser.
5. DOCUMENT
Create test reports for ONVIF IP cameras and screen shots for Analog &
HD coax cameras.
Page 26
171810.01 SecuriTEST® IP 20
SecuriTEST® IP User Manual
IP CAMERA TEST - IP Discovery / DIRECT IP CAMERA
Quick IP Device Discovery
The IP Discovery tool provides facilities for discovering and testing
a single directly connected IP camera
.
Touch ONVIF CAMERA to connect to ONVIF-compliant cameras.
Displays the IP address of the tester and the discovered IP address of the
connected camera
. The tester sets its IP address in the same sub-net as the camera.
Displays the results of the PING test. Touch start to PING the
detected camera to verify network connection.
Touch WEB BROWSER to access the camera via Chrome
Controls and indicates DHCP status
Touch REFRESH to start the IP Discovery again following a
timeout.
Touch NON-ONVIF CAMERA to access the Non-ONVIF test
function.
Displays the status of the discovered camera
Page 27
171810.01 SecuriTEST® IP 21
SecuriTEST® IP User Manual
IP CAMERA TEST – ONVIF / NETWORK CAMERA
ONVIF Camera Test
Cameras that are compliant with the standard
methods of communication established by the Open
Network Video Interface Forum (ONVIF) can be
connected and tested without the need to make any
manual
adjustments to the connection details
regardless of camera brand.
(Note that some cameras
may be only partially ONVIF compliant)
Touch an icon to display the camera setup menu, capture and play
photos and videos, Pan/Tilt/Zoom
(see PTZ section)
, RTSP address,
preview and create test
reports (see Test Report section). Touch
and drag tool bar to display the "?" icon.
Touch setting to adjust the ONVIF settings
Touch Add to add a new camera using its URL. Touch Refresh
to update the Device List
Displays the video stream from the connected camera. Double-tap
to switch full
-screen display on/off.
Displays a list of available cameras. Touch a camera to connect to it.
Displays the user name of the connected camera when logged in. When
logged out, allows user name and password to be entered.
Page 28
171810.01 SecuriTEST® IP 22
SecuriTEST® IP User Manual
ONVIF CAMERA TEST - PTZ
Touch Close to return to the ONVIF screen.
Touch Delete to remove the highlighted preset from the list
Highlight a preset then touch goto to instruct the camera to go to the specified
PTZ settings
Create a new preset by moving the camera to the desired position then touch set
preset
to add it to the list
Displays a list of PTZ settings previously set by the user.
Touch Left cruise or Right cruise to test the left/right pan position.
The Pan/Tilt/Zoom (PTZ) functions of IP cameras
can be tested using the
keypad arrow buttons or
screen gestures or by using user
-defined presets of
the angle, distance and objective as well as speed for
the PTZ.
PTZ presets can be programmed into the camera
and tested using this software tool.
The other parameters of the IP ca
mera can be
configured via ONVIF menu or WEB BROWSER.
Page 29
171810.01 SecuriTEST® IP 23
SecuriTEST® IP User Manual
IP CAMERA TEST - Chrome
The Chrome web browser provides an interface for connecting to the web servers in
connected cameras. This allows setting of the cameras through their web interface.
Note: Many cameras require the Microsoft ActiveX plug-in to display live video in a web
browser. ActiveX is not supported by the Android operating system.
Some non-ONVIF compliant cameras will display live video using alternative video
compression protocols.
Some of the cameras do not support all functions on Chrome browser. Please be aware
of this.
Enter the URL / IP address of the required camera .
Press
to close the browser
Page 30
171810.01 SecuriTEST® IP 24
SecuriTEST® IP User Manual
IP CAMERA TEST - Non ONVIF IP Camera Test
The Non ONVIF (IPCam) test screen provides facilities for discovering, viewing and
testing connected non-ONVIF compliant cameras using their IP address.
Touch Reset to cancel all settings. Touch Restore to go back to
the previous settings.
Touch Enter to connect to the specified camera
Enter the TCP / UDP port number for the required camera
Enter the user name and password of the camera
Search camera IP address
Touch Edit to go to the IP settings screen to set the IP address and Subnet
Mask of the tester, and the address of the gateway and
DNS.
RTSP stream subject availability of camera under test.
Show password
Select camera brand and model or select Auto to search automatically
Page 31
171810.01 SecuriTEST® IP 25
SecuriTEST® IP User Manual
ANALOG CAMERA TEST - CVBS
Cameras using the Composite Video Blanking and Sync (CVBS) analog standard can be
tested
Settings for Photo or Video file naming. Auto creates a file name
automatically. Manual allows user to set file name.
Touch +/- or drag the sliders to adjust the picture settings
Displays the video stream from the connected camera
Touch to display the Video Levels on the bottom left
corner. Displays the levels of the different
components of the Composite Video stream from
the connected camera
as shown on the right.
12VDC
Page 32
171810.01 SecuriTEST® IP 26
SecuriTEST® IP User Manual
ANALOG CAMERA TEST - PTZ
The Pan / Tilt / Zoom of Analog cameras can be controlled by the keypad or by screen
gestures.
Tap to display the PTZ control screen (may vary depending on the type of
camera):
To set each parameter, tap it and select from the displayed list or enter the required
number:
Protocol – Must match the camera setting
Coaxitron – Choose PTZ (controlled by keypad) or Menu ( controlled by on-screen
controls)
Port Type – Must match the camera setting
Baud Rate - Must match the camera setting
Address - Must match the camera setting
Pan Speed – Enter the required speed (0-63)
Tilt Speed - Enter the required speed (0-63)
Set Preset Position – Save the current PTZ setting and give it a number
Recall Position – Recall – Go to a previously saved PTZ position
Use screen gestures to control PTZ:
Slide left / right to control Pan and up / down to control Tilt
Pinch to Zoom out. Spread to Zoom in.
Use the keypad to control PTZ ( see Keypad section). Press to switch
Digital Zoom on. A thumbnail of the zoomed view is displayed at the bottom let of the
screen. Use the zoom and pan keys to adjust the zoomed view.
Page 33
171810.01 SecuriTEST® IP 27
SecuriTEST® IP User Manual
ANALOG CAMERA TEST - PTZ Address Scanning
When enabled, SecuriTEST IP will scan PTZ addresses in the analog video
modes. Scanning will stop when exiting analog video mode. Used for
connecting a single camera only. If connected to a head-end, multiple
cameras will be activated during the scanning process.
Note that the PTZ parameters must first be set to match the camera (
see
PTZ section).
SETUP >> PTZ Address Scanning >> ON
then ANALOG & HD CAMERA>>CVBS>>PTZ
Set protocol, communication port, communication rate, to match the PTZ
camera under test, then to press "Scanning" to start the PTZ camera's
address searching.
Touch “Auto scan +”. The address increments in steps of 1. When the
address is found, the PTZ camera will continue to pan right. Touch "Auto
scan(+) to stop address incrementing. Then use "Manual scan (-)" to
search the address until the camera stops panning right. At this point, the
address field shows the camera's PTZ address.
Touch “Auto scan -”. The address decrements in steps of 1. When the
address is found, the PTZ camera will continue to pan left. Touch "Auto
scan(+) to stop address decrementing. Then use "Manual scan (-)" to
search the address until the camera stops panning left. At this point, the
address field shows the camera's PTZ address.
Page 34
171810.01 SecuriTEST® IP 28
SecuriTEST® IP User Manual
ANALOG CAMERA TEST - Video Out
The Video Out function generates and displays a test pattern which can be used to test
TV monitors and cabling infrastructure via Analog/Test Output interface.
Select a coloured bars test pattern or a blue screen to be used for
the VIDEO OUT test stream.
Displays the Output test picture
Displays the received test pattern (for cable testing)
Select PAL or NTSC picture format
TV Monitor
Testing
Cable Testing
Page 35
171810.01 SecuriTEST® IP 29
SecuriTEST® IP User Manual
ANALOG CAMERA TEST – HD TVI
Cameras using the High Definition Transport Video Interface (TVI) standard can be
tested. HD Coax Camera - TVI/AHD/CVI are protocols that allow HD video from digital
cameras to be transmitted over coaxial cable allowing improved video quality with
existing cabling. SecuriTEST IP supports fixed and PTZ versions of these cameras.
Touch Photo to select and view snapshots
Touch Snapshot to capture a snapshot of the current scene
Touch Record to record video. Touch Stop to stop recording
Touch Play
back to select and play video recordings
Touch PTZ to set the Pan/Tilt/Zoom see
PTZ section
Touch Set to control Auto or manual naming of the photos and videos
Touch to display captured photos.
Displays video format (width x height in pixels) and frame rate
Touch to capture photos and videos.
Touch to play recorded videos.
(Common functions for
all
HD coax camera
types)
12VDC
Page 36
171810.01 SecuriTEST® IP 30
SecuriTEST® IP User Manual
ANALOG CAMERA TEST – HD CVI
Cameras using the High Definition Composite Video Interface (CVI) standard can be
tested.
Create and recall preset PTZ positions.
Set response speed of PTZ controls. Common functions for all HD Coax (
TVI, CVI and AHD)
UTC or RS485 Port settings
12VDC
Touch Photo to select and view snapshots
Touch Snapshot to capture a snapshot
of the current scene
Touch Record to record video. Touch Stop to stop recording
Touch Playback to select and play video recordings
Touch PTZ to set the Pan/Tilt/Zoom see
PTZ section
Touch Set to control Auto or manual naming of the
photos and videos
Page 37
171810.01 SecuriTEST® IP 31
SecuriTEST® IP User Manual
ANALOG CAMERA TEST - AHD
Cameras using the Analog High Definition (AHD) standard can be tested.
Navigate and use the camera-based settings menus with the On
Screen Display (OSD) menu navigation controls. (Also supported
on TVI, CVI and Coax cameras.)
12VDC
Touch Photo to select and view snapshots
Touch Snapshot to capture a snapshot of the current scene
Touch Record to record video. Touch Stop to stop recording
Touch Playback to select and play video recordings
Touch PTZ to set the Pan/Tilt/Zoom see
PTZ section
Touch Set to control Auto or manual naming of the photos and videos
Page 38
171810.01 SecuriTEST® IP 32
SecuriTEST® IP User Manual
CABLE TESTING - Cable Test
Cables connected between the Cable Test port (bottom of the tester) and the UTP port
of a Cable Tracer / Remote (powered by two AAA batteries - not included in package)
can be checked for correct continuity and identified as straight-through or crossover
cables. (The shield of STP cables is not tested)
Touch to display wiring diagrams for straight-through and
crossover cables
Diagrams showing the colour code and pin numbers. Faulty pins are
shown by a red cross
Displays the end-to-end connections of the cable being tested (only
if the test has passed)
Displays the ID number of the remote
Displays the detected configuration of the cable being tested.
UTP Port
Switch on
power
Page 39
171810.01 SecuriTEST® IP 33
SecuriTEST® IP User Manual
CABLE TESTING - RJ45 cable TDR
A Time Domain Reflectometer (TDR) in the tester can be used to measure the length
and estimated cable quality of a cable (excluding STP shield) with the other end
opened or shorted. To measure the impedance, reflectivity and skew, the cable need to
be connected to a Camera / Network port (top of tester). The length of each of the
four individual pairs in the cable is independently measured. (Note that this test does
not require a remote unit. However the skew can only be measured at 1000Mb/s when
the tester is connected to an active network port such as a switch)
Touch to display wiring diagrams for straight-through and
crossover cables
Touch to display diagrams of the ports
Displays open / short status of each cable pair
Displays the length of each cable pair
Touch to start single, continuous or advanced test. Use Advanced test
for reflection, impedance and skew. Use Continuous for best accuracy
and result stability.
Displays the approximate attenuation per 100m and cable quality ( good / poor /
contaminated
) for cables longer than 10 m. Threshold of colour is as following for
100m:
<=8dB Green
<=10dB Yellow
>10dB Red
Page 40
171810.01 SecuriTEST® IP 34
SecuriTEST® IP User Manual
CABLE TESTING - Tone Generator
The tester can generate a digital tone on the cable (UTP only – not STP) connected to
the Cable Test port. This tone can be detected using a non-contact tone probe to allow
the cable to be traced.
Touch a number to select the desired tone
Page 41
171810.01 SecuriTEST® IP 35
SecuriTEST® IP User Manual
IP NETWORK TEST - Ping
Ping is a standard network debugging tool used for testing if the connected IP camera
or other network equipment’s Ethernet port is working normally and the IP address is
correct.
TOOLS >> Network Tool >> Ping
Connect a network cable to the LAN port and click the icon to open the PING
tool. You can set your LOCAL (native) IP address, Remote IP address (e.g. IP camera),
Packet count, Packet Size, Packet delay time and Timeout. Press “Start” to start
pinging. If the IP camera or network device is not configured properly or not plugged
in, it will say “Destination host unreachable,” or have 100% packet loss. If the tester
connects to the device, the send and receive packets will have a 0% packet loss.
Page 42
171810.01 SecuriTEST® IP 36
SecuriTEST® IP User Manual
IP NETWORK TEST - IP Scan
TOOLS >> Network Tool >> IP Scan
Connect the cable to the LAN port, click icon . Set the IP address search range
by changing the Start and End IP addresses. (Note that the IP Scan test can only scan
within the local subnet.)
Click the “Start” button to scan the IP address range. You can also input an IP address
in the Port Number Scan to scan for open ports. (Note that the port scan can take a
long time and it is not recommended to use this function unless necessary.)
The “IPC” indication means that
this may be the address of a
camera.
Port number scan is mainly to check if the port is open and available for
service/traffic passing through. Often i
t takes much longer time to test
and it
is not recommended t
o use this test unless necessary.
Page 43
171810.01 SecuriTEST® IP 37
SecuriTEST® IP User Manual
IP NETWORK TEST - DHCP Server
Cameras that are equipped to use the Dynamic Host Control Protocol (DHCP) can
request an IP address from the tester’s DHCP server instead of using a fixed IP address.
TOOLS >> Network Tool >> DHCP Server
Switch the DHCP Server on/off
CAUTION!
Enabling a DHCP server in a network
that already has another DHCP server enabled can
cause the network to become unstable. Always
consult the network administrator before enabling
the DHCP server in a tester connected to a
network
Set up a pool of
addresses that the
DHCP serv
er can
assign
Double-tap to display DHCP
clients in the network,
updated in real time
Set the length of time that the
address will be valid in the camera
Lists all of the cameras that
have been assigned IP
addresses
Set up the IP address of the tester
(Note that the tester must have a
static address and not be in Wi
-Fi
mode) Refer to IP Settings section.
Page 44
171810.01 SecuriTEST® IP 38
SecuriTEST® IP User Manual
IP NETWORK TEST - Available IP
TOOLS >> Network Tool >> Available IP
This tool is used to check the network to find available IP addresses. A camera with a
fixed IP address will only work correctly in the network if its IP address is not already in
use by another device. If the camera’s IP address is already in use, it must be changed
to a free one before it can be connected to the network.
IP address is
available
IP address is
already in use
-
camera address
must be changed
to a free one
Add a new IP address to include in
the scan
Remove the selected IP
address from the scan
Start the scan
Page 45
171810.01 SecuriTEST® IP 39
SecuriTEST® IP User Manual
IP NETWORK TEST - Network IP Scan
TOOLS >> Network Tool >> Network IP Scan
Connect the cable to the LAN port, click icon . This test scans the network over
multiple sub-nets. (Note that this can take a long time to complete.)
Page 46
171810.01 SecuriTEST® IP 40
SecuriTEST® IP User Manual
IP NETWORK TEST - Data Monitor (RS485)
This tool is used to check the RS485 communication codes transmitted by a DVR or
control keyboard.
TOOLS >> Data Monitor
Transmit the message
Edit the message
Adjust the port settings:
Transmitted and
received messages
Page 47
171810.01 SecuriTEST® IP 41
SecuriTEST® IP User Manual
RESULTS AND TRANSFER - Test Report
Touch to open the report
information window
Touch a saved report to select it
for viewing
Touch to open the selected
report
Report Information Window
Touch to create and save the
report
Touch to attach snap shots and
logo for the test report
PDF is created and stored on
the internal storage
in the JOBS
folder
.
The final step in testing and commissioning cameras is to
record the testing in the form of a Test Report that can be
given to the client as proof of correct installation and
operation.
Fill in the project and operator
details
Page 48
171810.01 SecuriTEST® IP 42
SecuriTEST® IP User Manual
RESULTS AND TRANSFER - JOBS
Jobs are used to organise all of the test results and resources into a folder structure in
the internal storage (internal SD card). The contents are categorised by type of file:
Shortcut copies all files from
internal SD card to external SD
card
.
Page 49
171810.01 SecuriTEST® IP 43
SecuriTEST® IP User Manual
RESULTS AND TRANSFER - File Explorer
The File Explorer provides a method for navigating the file structures of the various
tester memories, including the internal and external SD cards.
MY APPS >> File Explorer
To Copy a file to another folder in the tester:
• Navigate to the file
• Either:
o Select the file by ticking the box on the right hand side of the screen
o Tap the icon at the top of the screen
• Or:
o Touch and hold the file name
o Select Copy from the menu
• Navigate to the destination folder
• Tap Paste
To Copy a file from the tester to another device (PC or smart device):
• See File Transfer section
Page 50
171810.01 SecuriTEST® IP 44
SecuriTEST® IP User Manual
RESULTS AND TRANSFER - File Transfer
Three methods can be used to transfer files to and from external devices such as PCs
and smart devices:
1. Removable microSD card
• Use the Copy / Paste procedure described in the Jobs section to copy the
required file(s) on to the external SD card
• Eject the SD card by pushing it inwards
• Insert the SD card into an SD port or SD / USB adapter (provided as
standard accessory) in the target device
• Copy the required file(s) into the appropriate folder in the target device.
• (Reverse the process to copy from the external device to the tester)
2. File Transfer Protocol (FTP) Server
MY APPS >> File Explorer>> FTP
An FTP server can run in the tester. (
See FTP server.) This can be accessed by an external
device connected via a Wi-Fi or wired network.
3. Internet
Select Anonymous
login (no password
required)
Tap to start the FTP server
(
See FTP server)
This is the FTP address of the
tester. Enter it into the URL
bar of
the browser.
Files can be sent and received
over the Internet using
applications such as web e
-mail
or Dropbox as illustrated on the
right.
Select external or
internal SD card
Page 51
171810.01 SecuriTEST® IP 45
SecuriTEST® IP User Manual
MY APPS - Rapid Video
Rapid video is an App that allows the tester to quickly detect all cameras in the
connected network and to display the video streams. It quickly combines IP Discovery
and ONVIF into a single operation.
MY APPS >> Rapid Video
The tester automatically connects to a camera and displays the video stream (see
ONVIF):
If the camera is disconnected, tap Refresh to re-connect :
Page 52
171810.01 SecuriTEST® IP 46
SecuriTEST® IP User Manual
MY APPS - HIK (HIKVISION)
The HIK App searches for all Hikvision cameras in the network and allows the user to
activate any cameras and to view the video streams from them. This is specially
designed for Hikvision cameras and mainly used for large scale or batch camera
configuration to improve the efficiency.
MY APPS >> HIK
Tap to refresh the search list
Indicates the IP
details of the
selected camera
Modify / reset the settings
Tap to login to the selected
camera
Enter the login details
of the selected camera
Play the video stream
from the selected
camera
Out of the box cameras need
to be activated before they
can be used. Tap to activate
the selected camera
Lists the available cameras
and their activation status.
Tap a camera to select it
Page 53
171810.01 SecuriTEST® IP 47
SecuriTEST® IP User Manual
MY APPS - DH (DAHUA)
The DH App searches for all Dahua cameras in the network and allows the user to
activate any cameras and to view the video streams from them. This is specially
designed for Dahua cameras and mainly used for large scale or batch camera
configuration to improve the efficiency.
MY APPS >> DH
Tap to refresh the search list
Indicates the IP
details of the
selected camera
Modify / reset the settings
Tap to login to the selected
camera
Enter the login details
of the selected camera
Play the video stream
from the selected
camera
Out of the box cameras need
to be activated before they
can be used. Tap to activate
the selected camera
Lists the available cameras
and their activation status.
Tap a camera to select it
Page 54
171810.01 SecuriTEST® IP 48
SecuriTEST® IP User Manual
MY APPS - RTSP Player
The RTSP Player app will allow you to view the RTSP video stream from an IP camera.
If you were unable to view your camera via the ONVIF or Test apps, it is possible your
camera will have an RTSP stream and you can view live video using this method.
MY APPS >> RTSP Player
Indicates the tester's IP address
Set the user name
and Password of the
IP camera
Tap to show a list of used
RTSP address search for RTSP
enabled cameras in
the
network and to select one
from the list to play
Set up or scan for the
Camera's IP address
Tap to view the RTSP stream
Edit the tester's IP address
Page 55
171810.01 SecuriTEST® IP 49
SecuriTEST® IP User Manual
SOFTWARE UPDATE - Local Update
The tester software can be updated in two ways - Manual and Auto update. Auto is
recommended for end users and Manual is for IDEAL and service engineers to use.
Note: The AUTO function will only update the IDEAL Networks' own software. Any
third party software will not be updated automatically unless MANUAL update is used.
SETUP >> System >> Update
Note: Users who install / update unapproved third party APPs into the tester take full
responsibility for the consequences. IDEAL Networks will not take any responsibility or
support these APPs if operation issues are caused.
Page 56
171810.01 SecuriTEST® IP 50
SecuriTEST® IP User Manual
TOOLS - Notepad
Notepad is a useful tool for making notes about the tests to attach to Test Reports
TOOLS >> Notepad
Open an existing text file:
Save the new text note to a file:
Write a new text note
Page 57
171810.01 SecuriTEST® IP 51
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION - Interfaces:
Ethernet port:
o Ethernet 100/1000Base-T - LAN/Network/Camera/RJ45 TDR test (1000Base-T), mRJ45 cable TDR test (1000Base-T)
RJ45 port:
o PoE IN - Pass-through PoE to the Ethernet port only no data pass through.
o Cable test - Cable test only Not Ethernet, no network connection.
Wi-Fi:
o Built in Wi-Fi 802.11b/g/n (2.4GHz only) up to speed 150Mb/s client to access the network for testing.
Coax port:
o BNC (f) video IN/HD Coax IN – Analog, TVI, CVI, AHD input
o BNC (f) video out – Analog video bar output
RS485 port: RS485 male “Phoenix” type connector for PTZ control and communications test
HDMI port:
o HDMI IN:
o HDMI supports: 720×480p /720×576p /1280×720p /1920×1080p /1024×768p/1280×1024p /1280×900p
/1440×900p video formats.
o Does not support HDCP copy protected video sources
o HDMI OUT: 1 channel HDMI output1280x720p, 1920x1080p user selectable.
Audio port:
o Audio IN: 3.5mm female socket for audio line in
o Audio Out: 3.5mm female socket for audio line out
DC output: 4.0x1.7mm female socket for 12V/2A DC output (center positive polarity)
USB port: Type A USB on 5V/2A DC power output only (No data transfer)
SD card slot: MicroSD card reader
DC input: 12V DC charge port with 5.5x2.1mm socket. Tester can operate and charge battery simultaneously.
LED Indication
Battery:
o ON - charging,
o OFF - fully charged when charge is ON or
o OFF – no charging when charge is OFF
o Flash – battery switch is OFF or no battery fitted (charge LED is ON)
Charge:
o ON - External DC 12V IN is plugged in
o OFF - External DC 12V IN is not plugged in
Tx & Rx:
Flash - Tx & Rx data for RS485
ON – Standby (both Tx & Rx ON)
Page 58
171810.01 SecuriTEST® IP 52
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION – Camera Test Functions
IP Camera Test:
o Max video input resolution: 4K (8MP).
o Codec support: MJPEG, MPEG4, H.264, H.265 (mainstream)
o ONVIF support: relevant part of profile S,Q,G
o IP address discovery & assign: auto discover static IP address of direct-connected camera or assign IP address to the
camera with dynamic IP address setting ( from internal DHCP server) automatically.
o Stream support: RTSP (Real Time Streaming Protocol)
o Non ONVIF and proprietary IP camera support: manual IP address, port and model selection for non ONVIF supported
cameras brand including ACTi, AIPU, APD, Axis, Aebell, Arecont Vision, BILL, BM, Bestecher, Bosch, CityTech, CYZ,
Changying, Colin, Costar, Dahua , DOZENY, DVO, DVSONE, Devele, Etrovision, FOKO, FORSECU, FS, Finetida, GOLBONG,
GREAT, Geovision, Grandeye, HI-SHARP, Hikvision, HISIDE, HZWS, HanbangGaoKe, HawKeye, Hitron, Honewell, HuiSun,
hongben, ISEC, Infinova, JETVIEW, JOOAN, JOVISION, JUAN, Jbvideo, JieGao, JingShiKang, KEDACOM, KINPUS, KeJun,
KumKang, LEFOUND, LILIN, LanDunSiAn, Longse, MaxxOne, NJBESTWAY, Neitway, OSKA, PN3D, Panasonic, Pelco,
PengRunDa, Pinshi, QIDUN, Samsung, SANTACHI, SHIKO,SONY, STJIATU, STYCO, Safer, SecurityTronix, Seeyou, SongXin,
Sunell, SuperSight, TBTEC, TIANDY, TP-LINK, TVT, TianLong, TruVue, Uniview, VIDIACNET,VIVOTEK, VSTON,VVS-CCTV,
VideoNet, Vista, WAPA, WATCHMAN, WEISKY, Woshida, XiangWei, XinLong, YH, YIDUN, YJX, YSJ, YXAF, YueTian,
YunShiAn, ZKTeco, ZLD …
o PTZ, focus, aperture: Key pad and screen gesture to control of aperture, zoom, focus, pan, tilt.
o Digital zoom: Up to 20 times (subject to camera availability)
o Rapid video: One key discovery of active network cameras and access to camera setup and programming via ONVIF.
Web browser: Chrome
Analog (CVBS) camera test:
o Video input: 1 channel analog CVBS signal PAL & NTSC auto detection
o Video level meter: Peak video signal level, Sync signal level, Colour, Chroma level measurement
o Video output: colour bar, blue or black full screen in NTSC or PAL formats.
o Dual window display: CVBS floating on screen and IP camera test results at the same time for analog and IP converter
test monitor
o PTZ control: Supports RS485 control, Baud 600-115200bps, Compatible with more than 30 protocols such as PELCO-
D/P, Samsung, Panasonic, Bosch etc. (detail see HD Coax PTZ part)
o PTZ address scan: auto detect camera’s PTZ address
o PTZ data monitoring: Captures and analyses the command data from PTZ controller. Manual transmit of hexadecimal
codes in RS485 for PTZ control testing.
HD Coax (TVI, CVI, AHD) camera test:
o TVI: 8MP (4K) 3840 x 2160 15 fps, 5MP 2592 x 1944P 12.5/20 fps, 4MP 2688 x 1520P 15fps; 2560 x 1440P 15/25/30 fps,
3MP 2048 x 1536P 18/25/30 fps, 2MP (1080P) 1920 x 1080P 25/30 fps, 720P 1280 x 720P 25/30/50/60 fps, UTC control/
call OSD menu
o CVI: 8MP (4K) 3840 x 2160 12.5/15 fps, 4MP 2560x1440P 25F/30 fps, 1080p 1920 x 1080P 25/30 fps, 720p 1280 x 720P
25/30/50/60fps, UTC control d call OSD menu
o AHD: 5MP 2592 x 1944P 12.5/20 fps, 4MP 2560x1440P 15/25/30 fps, 3MP 2048x1536P 18/25/30 fps, 1080p 1920x1080P
25/30fps,720P 1280x720P 25/30 fps ,UTC control d call OSD menu
o Images: Snapshot/view, video record/play, screenshot
o PTZ control:
Port type - UTC Coaxitron®:
PTZ - Address, pan speed, tilt speed, set & recall position
Menu - arrows control with address
Port type - RS485:
Protocol: ALEC, AD168(M-B), Bosch OSRD, CBC, DAT-SD, DH-YTC06, Fastrax, HD600, Hikvision,
Kalatel ASC, LC-NEW, LG-MULTIX, Lilin-FAST, Lilin-MLP2, Minking A01, Minking B01, Molynx, Panasonic,
Pelco D, Pelco P, Samsung, Samsung SPD, SIEMENS, SONY-EVI, Santachi, TeleEye DM2, Vcltp, Vicon,
WV-CS850, YAAN, YAAN-0, YAAN-1
Baud rate: 150, 300, 600,1200,2400,4800,9600,19200, 38400,115200
Address, Pand & Tilt speed, Position set & Recall
o Zoom: Key pad control manual & digital (5x max)
Page 59
171810.01 SecuriTEST® IP 53
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION – Electrical Test Functions
Power output:
o PoE: DC48V PoE/PoE+, 24W max
o DC 12V: DC12V/2A power for IP & analog cameras
o DC 5V: DC5V 2A power output via USB to charge portable devices
PoE & Voltage test
o PoE IN: voltage, power and pins used
o LAN/Network: voltage, power and pin used
o 12V DC IN: voltage, power consumed (operating and charging power consumption)
o 12V DC OUT: voltage, power consumed by attached device
o PoE link check: PD (Powered Device) port on cable Tracer/Remote Test’s PoE status of link and pairs used with LED
indicators for 12,36 or 45,78 pins.
Ethernet cable test:
o Twisted-pair test: Reports: – straight, crossed-pair, open, short and cross-over (MDI-MDIX) with Tracer/Remote.
o RJ45 TDR test: Length 180m (max), Resolution +/-1m; estimated attenuation (dB/100m or dB/100feet) with good, poor
and bad colour status; reflection %; impedance (Ω); delay skew (ns) (when connected to 1000Mb/s network device only),
pin number with pair length. Continuous and single test mode.
o Digital Tone generator: 4 different tone selections for cable tracing.
o Cable trace: Trace and locate cables with the included Tracer/Remote. Digital tone technology eliminates electrical
noise/hum associated with traditional analogue tracing probes. Eight (8) volume levels, headphone jack for use in noisy
environments, non-conductive tip to prevent short circuits and integrated LED flashlight. Requires 2 x 1.5V AAA (LR03)
batteries (not included).
Page 60
171810.01 SecuriTEST® IP 54
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION – General Test Functions
IP Network test:
o Traffic monitoring: real-time upstream/downstream bandwidth histogram, tester IP address and link speed and full/half-
duplex condition.
o Ping: Local & destination IP address, packet size, number of ping tests and inter-packet delay.
o IP Scan: Scan for active devices within selected IP address range (subnet). Scan selected IP address for available
TCP/UDP port services.
o Port flash: Flash the link LED on of the switch to visually identify the port to which SecuriTEST IP is connected.
o DHCP Server: Fully configurable DHCP server to allow dynamically configured devices to operate when a network router
is not installed. Start/stop IP address range, lease time, connected client list display.
o Trace Route: Display IP address and delay time of up to 30 hops (routers) between device and target URL/IP address.
o Available IP: Create list of IP addresses and to scan for availability checking. Tester will scan each address and identify if
the address is available or in use by a network device. Use to find available IP addressed when before configuring a new
device with a static address.
o Network IP Scan: Cross-subnet IP scan on any linked network. Lists IP address of devices on multiple subnets compared
to IP Scan function which only lists devices on the same subnet as the tester.
Media playback/record applications:
o Video: RTSP player, Video player, VLC
o Audio: Audio recorder, Audio player
Image capture:
o Capture still image from connected camera (can be attached to test reports).
o Record video stream from connected camera.
o Capture current tester screen.
Audio:
o Audio IN: 1 channel audio signal input from camera to record, listen and play via media player or audio recorder/player;
2.5 mm (1/8”) connector.
o Audio OUT: 1 channel audio signal output to monitor audio from cameras with microphone; 2.5 mm (1/8”) connector.
o Speaker: Internal two speakers for system indicators and audio playback from cameras or other media files.
Test report (ONVIF only): PDF format with
o Company/customer project details,
o Tester information,
• Serial number/hardware version/firmware version/software version
• Date/time set
o Date/time of test conducted
o Camera manufacturer/model/name/software version/Date & time
o Camera network configuration,
o Link speed and duplex
o IP/gateway/DNS/MAC addresses, subnet mask
o Dynamic/static configuration
o Video stream information,
o Video resolution
o Frame rate
o Bit rate (kb/s)
o Encoding (CODEC) type
o Attach up to six (6) video still snapshot images,
o Operator’s notes
o Attach company/customer logo
Quick Access Shortcut menu: Single button access to eight (8) user-selectable functions
Remote view: View tester screen on other network device using RTSP (Real Time Streaming Protocol).
Page 61
171810.01 SecuriTEST® IP 55
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION – Results, Upgrade and Help
JOBS: Shortcut to user storage area with folders for Audio/ Logos/ Photos/ Reports/ Screenshots/ Videos.
Single button copy all files/directories from internal JOBS folder to external SD card.
File management:
o File explorer: copy, save, delete, cut, paste, transfer to internal and external SD card
o FTP: results to be accessed and managed via FTP with tester configured as a server or client.
o MicroSD card: transfer results to other devices or install software updates.
Upgrade: Auto & manual updates from microSD card.
Help
Video introduction: a quick video clip for basic operation introduction
User guide: Context sensitive on-line help
Quick reference guide: a quick reference guide for starting to operate the tester
FAQ: a list of commonly asked questions regarding to tester operation.
Page 62
171810.01 SecuriTEST® IP 56
SecuriTEST® IP User Manual
TECHNICAL SPECIFICATION – General
Display:
o Screen: 7 inch capacitive touch screen with 1920x1200 resolution (324 ppi).
o Screen locking: user password setting for secured tester access.
o Screen rotation: rotating screen for ceiling camera adjustment before mounting.
o Sleep timer: 1-30 min, disengage.
Storage: 10GB internal SD card, 8GB external microSD card included (supports up to 16 GB).
Date & Time: Date, Time & time zone selection, 24 hours format, manual and auto sync.
Power: Charger: input 110-240VAC, 50/60Hz, 0.6A; output 12VDC, 2A, centre pin positive polarity; US, UK, EU, Australia AC plug
adapters.
Battery:
o Capacity: Field user exchangeable 7.4V Lithium polymer battery, 5000mAh, 37Wh
o Operation time: 10 hour (typical) continuous operation without external PoE/DC12V load; 4.5hours (typical) with 3.5 watt
PoE camera load.
o Charge time: < 8 hours from empty.
Language: English, French, German, Spanish, Italian, Portuguese, Chinese
Length units: meter, feet
Operating Temperature: -10oC - +50 oC (50 oF - 122 oF)
Operating Humidity: 30% - 90%
Dimension 252 mm x 160 mm x 48 mm/ 10.0 in x 6.3 in x 1.9 in (approximate)
Weight: 1.0 Kg/2.2 lbs (including battery)
Standard compliance
CE RED directive:
• EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
• EN 301 489-1 V1.9.2 (2011-09)
• EN 301 489-17 V2.2.1 (2012-09)
• EN 300 328 V1.9.1 (2015-02)
• EN 62479:2010
FCC:
• FCC Part 15 Subpart B
RoHS:
• EN62321:2012
• EN 14372:2004
• EPA 3540:1996
Tone Tracer/Remote CE Directive:
• EN55032:2015
• EN61000-3-2:2014
• EN61000-3-3:2013
• EN55024:2010+A1:2015
Page 63
Loading...