ICP ROCKY-C400EV User Manual

Intel

10/100Mb LAN & VGA

ROCKY-C400

®

Celeron® Processor

CPU Board with

User Manual

Version 1.0

March 29, 2004

Copyright Notice

The information in this document is subject to ch ange without prior notice in order to improve reliability , design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indir ect, special, incidental, or consequential damages arising out of the use or inability to use the p roduct or documentation, ev en if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

ROCKY-C400 is a registered trademark of ICP Electronics Inc., IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. AMI is a registered trademark of American Megatrends Inc. , Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

2

Table of Contents

CHAPTER 1. INTRODUCTION ......................................5

1.1 S

1.2 P

PECIFICATIONS

ACKAGE CONTENTS

...................................................... 6

................................................. 7

CHAPTER 2. INSTALLATION........................................8

2.1 L

2.2 C

2.3 C

2.4 B

2.5 D

2.6

RS422/485

AYOUT DIAGRAM

LEAR OMPACT FLASH CARD MASTER/SLAVE MODE SETTING UZZER FUNCTION SETTING

ISKONCHIP

CMOS S

ETUP

™ F

SETTING

IMENSIONS

& D

................................. 8

.............................................. 11

....... 11

...................................... 11

LASH DISK MEMORY ADDRESS SETTING

............................................. 13

... 12

CHAPTER 3. CONNECTION ........................................14

3.1 F

LOPPY DISK DRIVE CONNECTOR

3.2 PCI E-IDE D

3.3 P

3.4 USB P

3.5 P

3.6 S

3.7 K

3.8 I

3.9 F

3.10 VGA C

3.11 ATX C

3.12 E

3.13 PS-ON C

3.14 LAN RJ45 C

3.15 E

3.16 C

3.17 A

ARALLEL PORT

ORT CONNECTORS

OWER BUTTON SWITCH

ERIAL PORTS EYBOARD/MOUSE CONNECTOR

R

DA I

AN CONNECTOR

XTERNAL SWITCHES AND INDICATORS

XTERNAL

OMPACT FLASH STORAGE CARD SOCKET UDIO CONNECTORS

NFRARED INTERFACE PORT

ONNECTOR

LED C

3.18 RS422/485 C

ISK DRIVE CONNECTOR

..................................................... 16

......................................... 17

.......................................... 17

...................................................... 18

................................................... 20

.................................................. 20

.................................................. 21

............................................... 22

........................................... 23

ONNECTOR

...................................... 23

............................................... 25

ONNECTORS

....................................... 25

................................ 14

........................... 15

.................................. 18

............................... 19

......................... 22

...................... 24

CHAPTER 4. BIOS SETUP ..........................................27

4.1 I

4.2 S

4.3 S

4.4 M

NTRODUCTION

TARTING SETUP ETUP SUMMARY

AIN MENU SELECTIONS

..................................................... 27

................................................... 27

.......................................... 29

3

4.5 S

4.6 A

4.7 A

4.8 P

4.9 PCI / P

4.10 P

4.11 H

TANDARD DVANCED DVANCED CHIPSET SETUP SELECTIONS

OWER MANAGEMENT SETUP SELECTIONS

LUG AND PLAY SETUP SELECTIONS

ERIPHERAL SETUP SELECTIONS

ARDWARE MONITOR SETUP SELECTIONS

APPENDIX B. E

CMOS S CMOS S

2

KEY™ FUNCTION................................45

ETUP SELECTIONS ETUP SELECTIONS

................................. 41

......................... 29

......................... 31

........................ 36

...................... 37

..................... 39

...................... 42

APPENDIX C. ADDRESS MAPPING ...............................46

APPENDIX D. ATX POWER SUPPLY ..............................48

APPENDIX E. HOW TO USE THE WAKE-UP FUNCTION.50

4

Chapter 1. Introduction

The ROCKY-C400 ATX/AT main board is a high-performance computer mainboard based on the VIA VT8601T and VT82C686B chipset. It is designed fo r IN TEL® CELERON® processor, making it an ideal product for costeffective CPU board markets.

The VIA® Apollo PLE133 (VT8601T) is a INTEL® CELERON® processor system logic north bridge with the addition of 133 MHz capability for both the CPU and SDRAM interfaces. VIA® Apollo PLE133 may be used t o implement both desktop and notebook personal computer systems from 100MHz to 133MHz based on CELERON®. The primary features of the VIA® Apollo PLE133-North Bridge are: INTEL® CELERON® CPU (Front Side Bus) Interface (100 / 133MHz), SDRAM Memory Interface (100 / 133MHz), 32-bit PCI with Integrated 2D / 3D graphics accelerator.

®

Apollo PLE133

The VT82C686B PSIPC (PCI Super-I/O Integrated Peripheral Controller) is a high integ ration, high performance, powerefficient, and high compatibility device that supports both Intel and non-Intel based processors to PCI bus bridge functionality, ensuring a complete Microsoft PC99-compliant PCI/ISA system.

5

1.1 Specifications

Intel

•

Bus: PICMG Bus(Support PCI Master x 4)

•

DMA channels: 7

•

Interrupt levels: 15

•

Chipset: VIA

•

®

Celeron

®

(FSB: Supports 100/133MHz)

®

VT8601T (Integrated 2D / 3D graphics

accelerator.) & VT82C686B

RAM memory: Two 168-pin DIMM sockets . Maximum

•

memory is 1GB.

Ultra ATA/33/66/100 IDE Interface : Two PCI

•

Enhance IDE hard drives. The south bridge VT82C686B supports Ultra ATA/33/66/100 IDE interface.

Floppy disk drive interface : Supports 2.88 MB,

•

1.44MB, 1.2MB, 720KB, or 360KB floppy disk drive.

Two high speed Series ports : NS16C550 compatible

•

UART’s

Bi-directional Parallel Port : IEEE1284 compatible

•

IrDA port : Supports Serial Infrared(SIR) and Amplitude

•

Shift Keyed IR(ASKIR) interface.

USB port : Equipped with four USB ports for future

•

expansion.

Intel 82551ER or REALTEK RTL8100 Fast Ethernet

•

Multifunction PCI Controller : IEEE 802.3u AutoNegotiation support for 10BASE-T/100BASE-TX standard. Fast back-to-back transmission support with minimum interframe spacing. Connected to your LAN via RJ45 connector.

Keyboard connector & PS/2 Mouse Port on-board

•

Power Consumption : +5VSB @ 200mA, +5V @ 2.8A,

•

+12V @ 170mA (400MHz with 512MB SDRAM x 2, Windows2000 )

Operating Temperature : 0° ~ 55° C ( CPU needs Cooler)

•

6

1.2 Package Contents

In addition to this User Manual, the ROCKY-C400 package includes the following items:



ROCKY-C400 Single Board Computer x 1



IDE HDD Cable x 1



FDD Cable x 1



RS-232/Print Cable x 1



Y Cable x 1



Driver CD x 1

If any of these items are missing or damaged, please contact the dealer from whom you purchased the product. Be su re to save the shipping materials and carton in case you want to ship or store the product in the future.

7

Chapter 2. Installation

This chapter describes how to install the ROCKY-C400. First a layout diagram of the ROCKY-C400 is shown, followed by unpacking information that should be carefully followed. The jumpers and switch settings for the ROCKY-C400 configuration, such as CPU type selection, system clock setting, and watchdog timer, are also listed.

2.1 Layout Diagram & Dimensions

(Please turn to the next two pages for layout diagram and

dimensions.)

8

9

10

2.2 Clear CMOS Setup

To clear the CMOS Setup (for example if you have forgotten the password, you should clear the CMOS and then re-set the password), you should close the JBAT1 (2-3) for about 3 seconds, then open it once more. This will s et back to normal operation mode.

JBAT1 : Clear CMOS Setup

•

  

1 2 3

JBAT1 DESCRIPTION

1-2

(default)*

Short 2-3 Clear CMOS Setup

Keep CMOS Setup

(Normal Operation)

2.3 Compact Flash Card Master/Slave Mode Setting

The Compact Flash socket is type II, and uses IDE 2.

JP3 : Master/Slave Mode Setting

•

2



1



JP3 DESCRIPTION

SHORT * MASTER

OPEN SLAVE

2.4 Buzzer Function Setting

CN4(2-4) : Enabled/Disabled Onboard Buzzer

•

Function

11

2 4 6 8 10 12

           

1 3 5 7 9 11

2 - 4 DESCRIPTION

SHORT * Enabled

OPEN Disabled

2.5 DiskOnChip™ Flash Disk Memory

Address setting

The DiskOnChip™ Flash Dis k Chip (DOC) is produced by MSystems. Since DOC is 100% compatible with the hard disk, no extra software utilities are required. It is, in other words , “plug and play” - easy and reliable. At the present time, the DOC is available with between 2MB and 144MB.The MD-

2200-Xmb series DOC will share only 8KB memory address.

• JP2: DiskOnChip Memory Address Settings

2 4 6 8 10 12 14

             

1 3 5 7 9 11 13

ADDRESS 1-2 3-4 5-6 7-8 9-10 11-12 13-14

CC000 OPEN OPEN CLOSE OPEN OPEN CLOSE CLOSE CE000 OPEN OPEN OPEN CLOSE OPEN CLOSE CLOSE D0000 CLOSE OPEN OPEN OPEN CLOSE OPEN CLOSE D2000 OPEN CLOSE OPEN OPEN CLOSE OPEN CLOSE D4000 OPEN OPEN CLOSE OPEN CLOSE OPEN CLOSE D6000 OPEN OPEN OPEN CLOSE CLOSE OPEN CLOSE

D8000 CLOSE OPEN OPEN OPEN OPEN OPEN CLOSE DA000 OPEN CLOSE OPEN OPEN OPEN OPEN CLOSE DC000 OPEN OPEN CLOSE OPEN OPEN OPEN CLOSE DE000 OPEN OPEN OPEN CLOSE OPEN OPEN CLOSE

12

2.6 RS422/485 setting

•

JP5:

JP5 DESCRIPTION

1-2* RS-232

2-3 RS-485/422

13

Chapter 3. Connection

This chapter describes how to connect peripherals, switches and indicators to the ROCKY-C400 board.

3.1 Floppy Disk Drive Connector

ROCKY-C400 board is equipped with a 34-pin daisy-chain driver connector cable.

FDD1 : FDC CONNECTOR

•

2 4 6 … 30 32 34

   …       …   

1 3 5 … 29 31 33

PIN DESCRIPTION PIN DESCRIPTION

1 GROUND 2 REDUCE WRITE 3 GROUND 4 N/C 5 GROUND 6 N/C 7 GROUND 8 INDEX#

9 GROUND 10 MOTOR ENABLE A# 11 GROUND 12 DRIVE SELECT B# 13 GROUND 14 DRIVE SELECT A# 15 GROUND 16 MOTOR ENABLE B# 17 GROUND 18 DIRECTION# 19 GROUND 20 STEP# 21 GROUND 22 WRITE DATA# 23 GROUND 24 WRITE GATE# 25 GROUND 26 TRACK 0# 27 GROUND 28 WRITE PROTECT# 29 N/C 30 READ DATA# 31 GROUND 32 SIDE 1 SELECT# 33 N/C 34 DISK CHANGE#

14

3.2 PCI E-IDE Disk Drive Connector

You can attach up to four IDE( Integrated Device Electronics) devices.

IDE1 : Primary IDE Connector IDE2 : Secondary IDE Connector

IDE1 / IDE2 : IDE Interface Connector

•

2 4 6 … 36 38 40

   …       …   

1 3 5 … 35 37 39

PIN DESCRIPTION PIN DESCRIPTION

1 RESET# 2 GROUND

3 DATA 7 4 DATA 8

5 DATA 6 6 DATA 9

7 DATA 5 8 DATA 10

9 DATA 4 10 DATA 11 11 DATA 3 12 DATA 12 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 DATA 0 18 DATA 15 19 GROUND 20 N/C 21 DRQ 22 GROUND 23 IOW# 24 GROUND 25 IOR# 26 GROUND 27 CHRDY 28 REV. PULL LOW 29 DACK 30 GROUND-DEFAULT 31 INTERRUPT 32 N/C 33 SA1 34 N/C 35 SA0 36 SA2 37 HDC CS0# 38 HDC CS1# 39 HDD ACTIVE# 40 GROUND

15

3.3 Parallel Port

Usually, a printer is connected to the parallel port. The ROCKY-C400 includes an on-board parallel port, accessed via a 26-pin flat-cable connector PRN1.

PRN1 : Parallel Port Connector

•

2 4 6 … 22 24 26

   …       …   

1 3 5 … 21 23 25

PIN DESCRIPTION PIN DESCRIPTION

1 STROBE# 2 DATA 0

3 DATA 1 4 DATA 2

5 DATA 3 6 DATA 4

7 DATA 5 8 DATA 6

9 DATA 7 10 ACKNOWLEDGE 11 BUSY 12 PAPER EMPTY 13 PRINTER SELECT 14 AUTO FORM FEED # 15 ERROR# 16 INITIALIZE 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC

16

3.4 USB Port Connectors

The ROCKY-C400 is equipped with two USB ports for the future new I/O bus expansion.

•

USB1 / USB2 : 4 ports USB Connector

USB1 / USB2 Pin 8,7,6,5 for PORT 3 / 1 USB1 / USB2 Pin 1,2,3,4 for PORT 2 / 0

2 4 6 8

       

1 3 5 7

PIN DESCRIPTION PIN DESCRIPTION

1. VCC 2. GROUND

3. DATA1- 4. DATA0+

5. DATA1+ 6. DATA0-

7. GROUND 8. VCC

3.5 Power Button Switch

•

CN5 : 2 Pin Power Button Switch

1

 

PIN DESCRIPTION

1 ATX SW Pin1 2 ATX SW Pin2

2

17

3.6 Serial Ports

The ROCKY-C400 offers two high speed NS16C550 compatible UART’s with 16-byte Read/Receive FIFO serial ports.

•

COM1 / COM2 : Serial Port 10-pin Connector

6 7 8 9 10

         

1 2 3 4 5

PIN DESCRIPTION

1 DATA CARRIER DETECT (DCD) 2 RECEIVE DATA (RXD) 3 TRANSMIT DATA (TXD) 4 DATA TERMINAL READY (DTR) 5 GROUND (GND) 6 DATA SET READY (DSR) 7 REQUEST TO SEND (RTS) 8 CLEAR TO SEND (CTS) 9 RING INDICATOR (RI)

10 N/C

3.7 Keyboard/Mouse Connector

The ROCKY-C400 has a 6-pin DIN keyboard/mouse connector and a 5-pin keyboard connector..

•

P2 : 6-pin DIN Keyboard/Mouse Connector

PIN DESCRIPTION

1 KEYBOARD DATA 2 MOUSE DATA 3 GROUND 4 +5V 5 KEYBOARD CLOCK 6 MOUSE CLOCK

18

•

CN3 : 5-pin External Keyboard Connector

5



4



3

 

2



1

PIN DESCRIPTION

1 KEYBOARD CLOCK

2 KEYBOARD DATA

3 NC

4 GROUND

5 +5V

3.8 IrDA Infrared Interface Port

The ROCKY-C400 comes with an integrated IrDA port which supports either a Serial Infrared (SIR) or an Amplitude Shift Keyed IR (ASKIR) interface. When using the IrDA port, please ensure that COM2 is set in SIR or ASKIR mode in the BIOS’s Peripheral Setup so that RS-232 mode on COM2 is disabled.

•

J1 : IrDA connector

    

1 2 3 4 5

PIN DESCRIPTION

1 VCC

2 N/C

3 IR-RX

4 Ground

5 IR-TX

19

3.9 Fan Connector

The ROCKY-C400 also has a CPU with cooling fan connector and chassis fan connector, which can supply 12V/500mA to the cooling fan. There is a “rotation” pin in the fan connector, which transfers the fan’s rotation signal to the system BIOS in order to recognize the fan s peed. Please note that only specific fans offer a rotation signal.

•

JFAN1 / JFAN2 : CPU / SYS. Fan Connector

  

1 2 3

PIN DESCRIPTION

1 Ground 2 12V 3 Rotation Signal

3.10 VGA Connector

•

P3 : 15-pin Female Connector

PIN DESCRIPTION PIN DESCRIPTION

1 RED 2 GREEN

3 BLUE 4 NC

5 GROUND 6 GROUND

7 GROUND 8 GROUND

9 VCC / NC 10 GROUND 11 NC 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDCCLK

20

3.11 ATX Connector

The ROCKY-C400 is equipped with one standard ATX power connector

•

ATX1: 20-pin Connector

11 1

    . . . .    

20 10

PIN DESCRIPTION PIN DESCRIPTION

1 NC 11 NC

2 NC 12 -12V

3 GND 13 GND

4 +5V 14 PSON#

5 GND 15 GND

6 +5V 16 GND

7 GND 17 GND

8 Power Good 18 -5V

9 +5V SB 19 +5V 10 +12V 20 +5V

21

3.12 External Switches and Indicators

There are several external swit c h es an d indicators for monitoring and controlling yo u r CPU board. All functions are in the CN4 connector.

•

CN4 Pin Assignment and Functions :

2 4 6 8 10 12

           

1 3 5 7 9 11

FUNCTION PIN DESCRIPTION

SPEAKER

2 SPK SIGNAL 4 Buzzer6 NC

8 VCC 10 RESET RESET 12 GROUND

9 IDE_LED+ HDD LED 11 IDE_LED-

1 LED+ POWER LED

3 LED-(GROUND)

5 GROUND Reserved

7 NC

Jump for

Buzzer

3.13 PS-ON Connector

This connector is used to control the ATX power supply.

•

CN9 : PS-ON Connector (refer to Appendix D for

details )

  

1 2 3

PIN DESCRIPTION

1 Ground 2 PS-ON 3 +5V Standby

22

3.14 LAN RJ45 Connector

The ROCKY-C400 is equipped with dual Ethernet Controllers (Intel 82559 10/100Mbps, which are connected to the LAN via an RJ45 LAN connector. The pin assignments are as follows:

•

P1 LAN1 RJ45 Connector (10/100)

PIN DESCRIPTION PIN DESCRIPTION

1 TX+ 7 N/C 2 TX- 8 N/C 3 RX+ 9 Speed + 4 N/C 10 Speed 5 N/C 11 Active/LINK + 6 RX- 12 Active/LINK -

3.15 External LED Connector

The LED connector includes an Ethernet Link/Active LED, and an Ethernet speed LED.

•

CN1 External LED Connector

1 2

   

3 4

LED - LED + LED Function

1 2 LAN LINK LED 3 4 LAN Speed LED

23

3.16 Compact Flash Storage Card Socket

The ROCKY-C400 includes a slot for a Compact Flash Storage Card in IDE Mode(Using IDE 2).

•

CN2 : Compact Flash Storage Card Socket pin

assignment

PIN DESCRIPTION PIN DESCRIPTION

1 GROUND 26 CARD DETECT1 2 D3 27 D11 3 D4 28 D12 4 D5 29 D13 5 D6 30 D14 6 D7 31 D15 7 CS1# 32 CS3# 8 N/C 33 N/C

9 GROUND 34 IOR# 10 N/C 35 IOW# 11 N/C 36 OBLIGATORY TO PULL HIGH 12 N/C 37 IRQ15 13 VCC 38 VCC 14 N/C 39 MASTER/SLAVE 15 N/C 40 N/C 16 N/C 41 RESET# 17 N/C 42 IORDY 18 A2 43 N/C 19 A1 44 OBLIGATORY TO PULL HIGH 20 A0 45 ACTIVE# 21 D0 46 PDIAG# 22 D1 47 D8 23 D2 48 D9 24 N/C 49 D10 25 CARD DETECT2 50 GROUND

24

3.17 Audio Connectors

The onboard AC’97 CODEC supports several audio functions. The audio connectors are described below.

•

CN8:

2 4 6 8 10 12

           

1 3 5 7 9 11

PIN DESCRIPTION PIN DESCRIPTION

1 EAR OUT (LEFT) 2 EAR OUT (RIGHT)

3 GROUND 4 GROUND

5 LINE OUT (LEFT) 6 LINE OUT (RIGHT)

7 LINE IN (LEFT) 8 LINE IN (RIGHT)

9 GROUND 10 GROUND 11 MIC IN 12 GROUND

•

CD_IN1:

   

1 2 3 4

PIN DESCRIPTION

1. CD SIGNAL (LEFT)

2. GROUND

3. GROUND

4. CD SIGNAL (RIGHT)

3.18 RS422/485 Connectors

•

CN13:

   

1 2 3 4

25

PIN DESCRIPTION

1. TX2+

2. TX2-

3. RX2+

4. RX2-

26

Chapter 4. BIOS Setup

4.1 Introduction

This chapter discusses the Setup program built into the BIOS. which allows users to configure the system. This configuration is then stored in battery-backed CMOS RAM so that Setup information is retained whilst the power is o f f.

4.2 Starting Setup

The BIOS is immediately active when you turn on the computer. While the BIOS is activated, the Setup program can be entered in one of two ways:

1. By pressing <Del> immediately after switching the system on, or

2. by pressing the <Del> key when the following message appears briefly at the bottom of the screen during the POST (Power On Self-Test).

Press DEL to run SETUP.

4.3 Setup Summary

 Standard CMOS Setup:

Standard CMOS Setup to change time, date, hard disk type, etc.

 Advanced CMOS Setup:

Advanced CMOS Setup to configure system options.

 Advanced Chipset Setup:

Advanced Chipset Setup to configure chipset features.

27

 Power Management Setup:

Power Management Setup to configure power management features.

 PCI / Plug and Play Setup:

Configures PCI / Plug and Play features.

 Peripheral Setup:

Configures peripheral features.

 Hardware Monitor Setup:

Configures hardware monitor features.

Auto-Detect Hard Disks:



Selecting these options allow the user to configure th e drive named in the option. S elect Auto-Detect Hard Disks to allow AMIBIOS to automatically configure the drive. A list of drive parameters the appears on the screen.

 Change User Password:

Change the user password.

 Change Supervisor Password:

Change the supervisor password.

 Auto Configuration with Optimal Settings:

Load configuration settings that ensure the highest performance.

 Auto Configuration with Fail Safe Settings:

Load fails-safe configuration settings.

 Save Settings and Exit:

Write the current settings to CMOS and exit.

 Exit Without Saving:

Exit without saving the current settings.

28

4.4 Main Menu Selections

AMIBIOS HIFLEX SETUP UTILITY – VERSION 1.52

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI / Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Standard CMOS Setup for changing time, date, hard disk type, etc.

ESC:Exit ↑↓:Sel F2/F3:Color F10:Save & Exit

Figure 1:The Main Menu

4.5 Standard CMOS Setup Selections

AMIBIOS SETUP – STANDARD CMOS SETUP

Date (mm/dd/yyyy): Tue Mar 19,2002 Base Memory: 639 KB Time (hh/mm/ss) : 17:18:10 Extd Memory: 247 MB

Floppy Drive A: Not Installed Floppy Drive B: Not Installed LBA Blk PIO 32Bit Type Size Cyln Head WPcom Sec Mode Mode Mode Mode Pri Master: Auto On Pri Slave : Auto On Sec Master: Auto On Sec Slave : Auto On

Boot Sector Virus Protection Disabled Month: Jan – Dec ESC:Exit ↑↓:Sel

Day: 01 – 31 PgUp/PgDn:Modify Year: 1980 – 2099 F1:Help F2/F3:Color

Figure 2:Standard CMOS Setup

29

 Floppy A, B

Move the cursor to these fields and select the floppy type.

 Primary/Secondary Master/Slave LBA Mode

LBA(Logical Block Addressing) is a new IDE HDD access method to developed to overcome the 528-megabyte capacity bottleneck. If your IDE hard disk capacity is greater than 528MB, AMIBIOS can enable this LBA mode feature. The option is only for Primary Master IDE LBA mode.

 Primary/Secondary Master/Slave Block Mode

If your hard disk drive supports IDE block transfer mode, enable this option for a faster IDE hard disk drive transfer rate. The option is only for Primary Master Block mode.

 Primary/Secondary Master/Slave PIO Mode

This option enables Primary Master IDE PIO mode on the IDE, which can set proper cycle timings. The cycle timing between the IDE PIO mode value and IDE cycle timing is shown below : Mode 0 -> Timing ( 600ns ) Mode 1 -> Timing ( 383ns ) Mode 2 -> Timing ( 240ns ) Mode 3 -> Timing ( 180ns ) Mode 4 -> Timing ( 120ns ) Mode 5 -> Timing ( 60ns )

 Primary/Secondary Master/Slave 32Bit Mode

This option enables Primary Master IDE 32-bit data transfers on the IDE data port. If disabled,16-bit data transfer is used by the BIOS.32-bit data transfers can only be enabled if IDE prefetch mode is also enabled.

 Boot Sector Virus Protection

When this option is enabled, AMIBIOS issues a warning when any program or virus issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The settings are Disabled, Enabled.

30

4.6 Advanced CMOS Setup Selections

AMIBIOS SETUP – ADVANCED CMOS SETUP

Quick Boot 1st Boot Device 2nt Boot Device 3rd Boot Device Try Other Boot Devices S.M.A.R.T. for Hard Disks BootUP Num-Lock Floppy Drive Swap Floppy Drive Seek PS/2 Mouse Support System Keyboard Primary Display Boot To OS/2 Wait For ‘F1’ If Error Hit ‘DEL’ Message Display CPU MicroCode Updation L1 Cache L2 Cache System BIOS Cacheabled C000 32K Shadow

Enabled Disabled Disabled Disabled Yes Disabled On Disabled Disabled Enabled Present VGA/EGA No Enabled Enabled Enabled Enabled Enabled Enabled Cached

Available Options: Disabled > Enabled

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 3:Advance CMOS Setup

 S.M.A.R.T. for Hard Disks

Self-Monitoring, Analys is and Reporting Technolo gy. This option can help the BIOS to warn the user of a possible device failure and give the user a chance to back up the device before the failure actually happens. The settings are Auto, Disabled, Enabled.

Floppy Drive Seek



Set this option to Enabled to specify that floppy drive A: will perform a Seek operation at s ystem boot. The settings are Enabled or Disabled.

Quick Boot



When Quick Boot is selected, DRAM testing function will be disabled.

 1st Boot Device

This option sets the type of device for the first boot drives that the AMIBIOS

31

attempts to boot from after AMIBIOS POST completes. The settings are Disabled, IDE-0, IDE-1, IDE-2, IDE-3, Floppy, ARMD-FDD, ARMD-HDD, CDROM, SCSI.

2nd Boot Device



This option sets the type of device for the second boot drives that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, IDE-0, IDE-1, IDE-2, IDE-3, Floppy, ARMD-FDD, ARMD-HDD, CDROM.

 3rd Boot Device

This option sets the type of device for the third boot drives that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, IDE-0, IDE-1, IDE-2, IDE-3, Floppy, ARMD-FDD, ARMD-HDD, CDROM.

 Try Other Boot Devices

Set this option to Yes to instruct AMIBIOS to attempt to boot from any other drive in the system if it cannot find a boot drive among the drives specified in the 1st Boot Device, 2nd Boot Device, 3rd Boot Device, 4th Boot Device options. The settings are Yes or No.

BootUp Num-Lock



When this option is selected, Num Lock is turned off when the system is powered on s o the user can use the arrow keys on both the numeric keypad and the keyboard.

PS/2 Mouse Support



When this option is enabled, BIOS supports a PS/2- type mouse.

 System Keyboard

This option does not specify if a keyboard is attached to the computer. Rather,it specifies if error messages are displayed if a keyboard is not attached.This option permits you to configure workstation with no keyboard. The settings are Absent, Present.

 Primary Display

Select this option to configure the type of monitor attached

32

to the computer. The settings are Monochrome, Color 40x25,Color 80x25,VGA/PGA/EGA, or Not Install.

 Boot To OS/2

Set this option to Enabled if running OS/2 operating system and using more than 64MB of system memory on the motherboard. The settings are Disabled or Enabled.

 Wait For 'F1' If Error

If this option is enabled , AMIBIOS waits for the end u ser to press <F1> before continuing. If this option is disabled, AMIBIOS continues the boot process without waiting for <F1> to be pressed. The settings are Disabled or Enabled.

Hit 'DEL' Message Display



Disabling this option prevents "Hit <DEL> if you want to run Setup" from appearing when the system boots. The settings are Disabled or Enabled.

System BIOS Cacheable



When this option is set to enabled, the System ROM area from F0000-FFFFF is copied (shadowed) to the RAM for faster execution.

33

AMIBIOS SETUP – ADVANCED CMOS SETUP

C800 16K Shadow CC00 16K Shadow D000 16K Shadow D400 16K Shadow D800 16K Shadow DC00 16K Shadow

Disabled Disabled Disabled Disabled Disabled Disabled

Available Options: > Disabled Enabled Cached

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 4: Advance CMOS Setup

 C000,32k Shadow

When this option is set to enab led, the Video ROM area from C0000-C7FFF is copied (shadowed) to the RAM for faster execution. Disabled : The contents of the video ROM are not copied to

the RAM.

Cached: The contents of the video ROM area from

C0000h - C7FFFh are copied from the ROM to the RAM and can be written to or read from the cache memory.

Enabled: The contents of th e video ROM area from

C0000h - C7FFFh are copied (shadowed) from the ROM to the RAM for faster execution.

C800,16k Shadow



These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

34

 CC00,16k Shadow

These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

 D000,16k Shadow

These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

 D400,16k Shadow

These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

D800,16k Shadow



These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

 DC00,16k Shadow

These options enable shadowing of the contents of the ROM area named in the option title. The settings are Enable Disable, Cached. The ROM area that is not used by ISA adapter cards will be allocated to PCI adapter cards.

35

4.7 Advanced Chipset Setup Selections

AMIBIOS SETUP – ADVANCED CHIPSET SETUP

******** DRAM Timing ******** Configure SDRAM Timing by SPD DRAM Frequency SDRAM CAS# Latency

Memory Hole AGP Mode AGP Read Synchronization AGP Fast Write AGP Aperture Size AGP Master 1 W/S Write AGP Master 1 W/S Read USB Controller USB Device Legacy Support Port 64/60 Emulation

Disabled 133Mhz 3

Disabled 4x Enabled Disabled 64MB Disabled Disabled All USB Port Disabled Disabled

Available Options: > Disabled Enabled

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 5: Advanced Chipset Setup

36

4.8 Power Management Setup

Selections

AMIBIOS SETUP – POWER MANAGEMENT SETUP

ACPI Aware O/S ACPI Standby State Re-Call VGA BIOS at S3 Resuming Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Standby Time Out (Minute) Suspend Time Out (Minute) Throttle Slow Clock Ratio Display Activity IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ13 IRQ14 IRQ15

No S1/POS Enabled Enabled Disabled Disabled Disabled Disabled 50%-56.25% Ignore Monitor Monitor Ignore Monitor Ignore Ignore Ignore Ignore Monitor Ignore

Available Options: > No Yes

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 6: Power Management Setup

Power Management/APM



Set this option to Enabled to run APM (Advanced Power Management).

 Video Power Down Mode

Set this option to Enabled to allow the BIOS to power down the Video adapter and Monitor.

 Hard Disk Power Down Mode

Set this option to Enabled to allow the BIOS to power down the Hard Disk .

 Standby/Suspend Time Out (Minutes)

This option specifies the amount of system inactivity (in minutes) before the system will enters Standby/Suspend state.

37

AMIBIOS SETUP –POWER MANAGEMENT SETUP

Power Button Function Restore on AC/Power Loss

Resume On Ring/LAN Resume On LAN Resume On RTC Alarm RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second Power Type Select

Figure 7: Power Management Setup

On/Off Last State

Disabled Disabled Disabled 15 12 30 30 AT

Available Options: > On/Off Suspend

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

38

4.9 PCI / Plug and Play Setup

Selections

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

Plug and Play Aware O/S Clear NVRAM On Board PCI LAN Controller OnChip VGA Frame Buffer Size PCI Latency Timer (PC I C locks) The Vga Card After Bridge Primary Graphics Adapter Primary Graphics Adapter Allocate IRQ to PCI VGA PCI Slot1 IRQ Priority PCI Slot2 IRQ Priority PCI Slot3 IRQ Priority PCI Slot4 IRQ Priority DMA Channel 0 DMA Channel 1 DMA Channel 3 DMA Channel 5 DMA Channel 6 DMA Channel 7 IRQ3

No No Enabled 8MB 32 No PCI PCI Yes Auto Auto Auto Auto PnP PnP PnP PnP PnP PnP PCI/PnP

Available Options: No > Yes

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15

Figure 8: PCI / Plug and Play Setup

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP PCI/PnP

Available Options: > PnP ISA/EISA

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 9: PCI / Plug and Play Setup

39

 Plug and Play Aware O/S

If enabled, BIOS will configure only PnP ISA boot devices(i.e. all PnP ISA cards which have boot flag set). And PnP aware OS will co nfigure all other devices. If disabled, BIOS will configu re all devices.

 DMA Channel 0, 1, 3, 5, 6, 7

The option allow the user to specify the bus type used by each DMA channel. The settings are PnP or ISA/EISA

 IRQ3, 4, 5, 7, 9, 10, 11, 14, 15

The option specifies the bus that the specified IRQ line is used on. The user can reserve IRQs for legacy ISA adapter cards whilst determinin g if AMIBIOS should remove an IRQ from the pool of available IRQs passed to devices that are configurable by the system BIOS. The available IRQ pool is determined by reading the ESCD NVRAM. If more IRQs need to be removed from the pool, the user can optionally reserve the IRQ by assigning an ISA setting to it. Onboard I/O is configured by AMIBIOS. All IRQs used by onboard I/O are configured as PCI/PnP.

40

4.10 Peripheral Setup Selections

AMIBIOS SETUP – PERIPHERAL SETUP

OnBoard FDC Enabled

OnBoard Serial Port1 3F8/COM1 OnBoard Serial Port2 2F8/COM2 Serial Port2 Mode Normal Duplex Mode N/A OnBoard Parallel Port 378 Paralled Port Mode ECP EPP Version N/A Parallel Port DMA Channel 3 Parallel Port IRQ 7 OmBoard IDE Both OnBoard AC’97 Audio Enabled

 On-Board Parallel Port

This option specifies the base I/O port address of the parallel port on the moth erboard. The settings are Disabled, 378h, 278h, or 3BCh.

 Parallel Port Mode

This option specifies the parallel port mode. The settings are Normal, Bi-Dir, ECP, EPP. Normal : The n ormal parallel port mode is used. Bi-Dir : Use this setting to support bi-directional transfers

EPP : The parallel port can be used with devices that

ECP : The parallel port can be used with devices that

Available Options: Disabled > Enabled

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify F1:Help F2/F3:Color

Figure 10: Peripheral Setup

on the parallel port. adhere to Enhanced Parallel Port(EPP)

specifications. EPP uses the existing parallel port signals to provide asymmetric bi-d irectional data transfer driven by the host device.

adhere to Extended Capabilities Port (ECP) specifications. E CP uses the DMA protocol to achieve data transfer rates of up to 2.5 Megabits

41

per second, and provides symmetric bi-directional communication.

 Parallel Port IRQ

This option specifies the IRQ used by the parallel port. The settings are (IRQ)5, (IRQ)7. Parallel Port DMA Channel This option is only available if the setting for the Parallel Port Mode option is set to ECP. It sets the DMA channel used by the parallel port. The available settings are DMA Channel 0, 1, or 3.

4.11 Hardware Monitor Setup

Selections

AMIBIOS SETUP – HARDWARE MONITOR SETUP

System Temperature CPU Temperature CPU Fan Speed Chassis Fan Speed + 2.500V + 3.300V + 5.000V +12.000V

─＝≣

System Hardware Monitor

31ºC/87ºF 29ºC/84ºF 6300 RPM 0 RPM

2.625 V

3.490 V

5.070 V

12.046 V

≣＝─

ESC:Exit ↑↓:Sel PgUp/PgDn:Modify

F1:Help F2/F3:Color

Figure 11: Hardware Monitor Setup

42

Appendix A. Watch-Dog Timer

The WatchDog Timer is a device which ensure that standalone systems can recover from abnormal conditions that cause the system to crash. These conditions may result from an external EMI or a software bug. When the system stops working, hardware on the board will perform a hardware reset (cold boot) to bring the system back to a functioning state.

Three I/O ports control the operation of WatchDog Timer.

443 (hex) Write Set WatchDog Time period 443 (hex) Read 043/843

Read Disable the Watchdog Timer.

(hex)

Prior to enabling the Watchdog Timer, the user has to set the time-out period. The range of the timer is 1 to 255 sec, set in increments of 1 second. The user will need to send the timeout value to the I/O port – 443H, and then enable it by reading data from the same I/O port. This will activate the timer that will eventually time out and check and monitor the CPU board. This must be done within the time-out period that is set by the software, For additional help, please refer to the example program. Finally, disable the Watchdog timer by reading the I/O port -843H or 043H - otherwise the system could reset unconditionally.

Enable the refresh the Watchdog Timer.

A tolerance of at least 5% must be maintained to avoid unknown routines in the operating system (DOS), such as disk I/O that can be very time-consuming. Therefore if th e timeout period has been set to 10 seconds, the I/O port 443H must be read within 7 seconds.

43

Example assembly program:

TIMER_PORT = 443H TIMER_START = 443H TIMER_STOP = 843H

;;Initial Timer Counter

MOV DX, TIMER_PORT MOV AL, 8

;;8 seconds

OUT DX, AL MOV DX, TIMER_START IN AL, DX

. ;;Start counter

W_LOOP: MOV DX, TIMER_STOP IN AL, DX MOV DX, TIMER_START IN AL, DX

;;Restart counter

;;Add Your Application Here

CMP EXIT_AP, 0 JNE W_LOOP MOV DX, TIMER_STOP IN AL, DX

;;Exit AP

44

Appendix B. E2 Key™ Function

The ROCKY-C400 pro v ides an outstanding E2KEY™ function for system integrators. Based on the E

Passwords or Critic al Data can be stored in the 1Kbit EEPROM. Because the EEPROM is non-volatile memory, you don’t have to worry about losing important data.

The E

2

KEY™ is based on a 1Kbit EEPROM which is configured to 64 words(from 0 to 63). The user can access (read or write) each word at any time.

When you start to use the E

2

KEY™ the utility is already in the

package. The software utility will include four files as follows,

README.DOC E2KEY.OBJ EKEYDEMO.C EKEYDEMO.EXE.

2

KEY™, ID Code,

The E2KEY.OBJ provides two library functions for the user to

2

integrate in to their application with E

KEY™ function. These library functions (read_e2key and write_e2key) are written and compiled in C language. Please check the following statement, in order to easily implement it.

unsigned int read_e2key(unsigned int address)

2

/* This funct ion w ill ret urn t he E

KEY™’s data at address. The

address range is from 0 to 63. Return data is one word,16 bits */void write_e2key(unsigned int address,unsigned data)

2

/* This function will write the given data to the E

KEY™ at a certain address. The address range is from 0 to 63. The data value is from 0 to 0xffff. */ To start using the function, please refer to the included EKEYDEMO.C code.

45

Appendix C. Address Mapping

 IO Address Map

I/O address Range Description

000-01F DMA Controller #1 020-021 Interrupt Controller #1, Master 040-05F 8254 timer 060-06F 8042 (Keyboard Controller) 070-07F Real time Clock, NMI Mask 080-09F DMA Page Register 0A0-0BF Interrupt Control ler #2

0C0-0DF DMA Controller #2

0F0 Clear Math Coprocessor Busy 0F1 Reset Math Coprocessor 0F2 Core logic programming configuration

0F8-0FF Math Coprocessor 1F0-1F8 Fixed Disk 200-207 Game I/O

278-27F Parallel Printer Port 2 (LPT3) 2E8-2EF Serial Port 4

2F8-2FF Serial Port 2 300-31F Prototype Card 360-36F Reserved 378-37F Parallel Printer Port 1 (LPT2)

3B0-3BF Monochrome Display and Printer Adapter

(LPT1) 3C0-3CF Reserved 3D0-3DF Color/Graphics Monitor Adapter

3E8-3EF Serial Port 3 3F0-3F7 Diskette Controller

3F8-3FF Serial Port 1

46

 1st MB Memory Address Map

Memory address Description

00000-9FFFF System memory A0000-BFFFF VGA buffer C0000-C7FFF VGA BIOS F0000-FFFFF System BIOS 1000000- Extend BIOS

*Default setting

 IRQ Mapping Table

IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 Available

IRQ2 Cascade to IRQ Controller IRQ10 Available IRQ3 COM2 IRQ11 Available IRQ4 COM1 IRQ12 PS2 mouse IRQ5 Available IRQ13 FPU

IRQ6 FDC IRQ14 Primary IDE IRQ7 Printer IRQ15 Secondary IDE

 DMA Channel Assignments

Channel Function

0 Available 1 Available 2 Floppy disk ( 8-bit transfer ) 3 Available 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available

47

Appendix D. ATX Power Supply

The following notes show how to connect the ATX Power Supply to the backplanes and / or the ISBC card.

A. For backplanes with an ATX

Connector

1.

First disconnect the AC cord of the Power Supply from the AC source to prevent sudden electrical surge to the board.

2.

Next, check the type of your CPU board. All CPU boards listed on the next page support ATX power supply but have two types of power switch connection:

2.1. ROCKY-C400 (through Power Button & GND):

Connect the ATX power button switch to the pin 1 (power button) and pin 2 of the CN5 on the board, and connect the power cable from backplane to CN9 of the CPU card. If you want to turn ON the system, just press the button once. And If you want to turn off the power supply, please press the ATX power switch button for about 4 seconds. (Please refer to diagram on the next page.)

48

B. For backplanes with an ATX power

supply connector

For some SBC with no ATX power ON/OFF function, the user can control the ATX power supply via the backplane’s PS ON connector. Refer to the figure below: for the backplanes with ATX connector, the connection can be made simply as follows:

1. Connect the ON/OFF switch to Pin 2 (PS ON) and Pin 1 (GND) of connector CN2

2. You may now turn the power On and OFF by using the power switch

49

Appendix E. How to use the Wake-Up Function

The ROCKY-C400 provides two kind of Wake Up Function. This page describes how to use the Modem Wake-Up and LAN Wake-Up functions. Wake-Up function works whilst using ATX power supply,

Wake-Up By Modem Ring On: In CMOS SETUP, the user must set the option

LAN/Ring

on when there is a ring signal detected on the pin “RI” of the serial port.

Wake-Up On LAN (for Intel 82559 LAN-chip): In CMOS SETUP, the user must set the option

LAN/Ring

status, a LAN Link/Active LED is flashing. This status indicates that the LAN chip has entered standby mode and is waiting for a Wake-Up signal. You can use other computers to wake up your computer by sending ID to it.

: ID is the address of your system LAN. Every LAN chip has

ID a factory- set ID which you can find it from network information in WINDOWS.

ID’s format is xx-xx-xx-xx-xx-xx Example ID: 00905C21D4D5

to enabled. The ATX power su pply will be switched

to enabled. When th e computer is in power-down

Wake Up On

50

ICP ROCKY-C400EV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual