ICP H9MVX080J20A1, H9MVX100L20A1, T9MVX060F12A1 Installation Guide
INSTALLATION INSTRUCTIONS
90+ Upper Door Replacement
This kit is designed to replace the upper door on the N9MP1, N9MP2, N9MPD, *9MPD, *9MPT, *9UHX, *9MPV and
*9MVX series furnace.
* Denotes Brand
Read the entire instructions completely before starting the installation.
Examine kit to determine that the following parts are present with the
replacement upper door:
Parts List
Description Part# Qty
Model: Entry Level, C, H
Door Screw * 1014488 2
Diagnostic Labels
Single Stage 1012899 1
2-Stage 1013348 1
Operating Instruction 1013494 1
Seal Strip 1013144 3
Instructions 441 06 1063 01 1
Model: Tempstar
Door Screw * 1014488 2
Wiring Label
Single Stage 329530-101 1
2-Stage
Variable Speed (050)
Variable Speed
Warning Label
Operating Instruction
Instructions 441 06 1063 01 1
Diagnostic Label
Single Stage 1012899 1
2-Stage 1013348 1
Seal Strip 1013144 3
Faceplate
1013489 or 1013490 or 1013491 or 1013488 1
Trim Strip 1013487 2
or 330709-101 1
330605-101 1
or 330710-101 1
329548-101 1
330711-101 1
or 329532-101 1
1013810 1
or 330713-101 1
1013494 1
or 330712-201 1
Hole Plug 1/4"(634mm ) Diameter 1010714 2
If any part is missing, immediately contact your parts supplier.
Not all parts will be used.
* Denotes parts available through Fast Parts.
Others are available only through 90+ Upper Door Kits.
Figure1! N9MP1
_.,ii i
_.
_,_lnstall Diagn,
_ticLabelasshown
Model: N9MP2, *9MPD, *9MPT, *9MPV Series B (See Figure 2)
* Denotes Brand
1.
Place one Diagnostic Label below the sight glass on the inside
of the door.
NOTE: Part 1012899 for N9MP2, *9MPD
Part 1013348 for *9MPT, *9MPV
2.
Place Operating Instruction Label part 1013494 below the
diagnostic label on the inside of the door.
3.
Place seal strips (2) along the side edge on the inside of the
door and trim to length.
4.
Place another seal strip along the bottom edge on the inside of
the door and trim to length.
5.
(Tempstar only) Insert Face Plate on the designated holes on
the front of the door.
6.
(Tempstar only) Insert Hole plugs (2).
7.
(Tempstar only) Place Trim Strips (2) along the front side edge
of the door.
8.
Insert the two (2) screws into the screw holes located at the
front bottom of the door to install the door on the furnace.
Installation (Series B)
Model: N9MP1 Series B (See Figure 1)
1. Place Diagnostic Label part 1012899 at the right bottom cor-
ner on the inside of the door.
2. Insert the two (2) screws into the screw holes located at the
front bottom of the door to install the door on the furnace.
CUT HAZARD
Failure to follow this caution could results in bodily
injury.
Sheet metal parts may have sharp edges or burrs.
Use care and wear appropriate protective clothing
and gloves when handling parts.
NOTE: If replacing front door with machine thread thumbscrews, drill
new door screw holes from 1/8" (3.2mm) diameter to 1/4" (6.4mm)
diameter before inserting thumbscrews. Use machine thread thumb-
screws from original (old) door. Discard black door screws included
with this kit.
441 06 1063 01 Sept 2008
Figure 2 *9UHX, *9MPV, *9MVX
N9MP2, N9MPD, *9MPD, *9MPT,
_-_ZZZZZZZZZZZZZZZZZZZZZZ°__
-f
_ B
SEAL STRIP 12)
NOTE: LOCATE ON
BACKSIDE OF FLANGE.
FLUSH AT TOP OF
BOTTOM SEAL STRIP &
OUTSIDE FLANGES
Installation (Series A)
Model: N9MPD, *9UHX, *9MVX
* Denotes Brand
1.
(T9MVX only) Place Operating Instruction Label part
330712-201 below the sight glass on the inside of the door.
(See Figure 3)
2.
Place seal strips (2) along the side edge on the inside of the
door and trim to length.
3.
Place another seal strip along the bottom edge on the inside of
the door and trim to length.
4.
(Tempstar only) Insert Face Plate on the designated holes on
the front of the door.
5.
(Tempstar only) Insert Hole plugs (2).
6.
(Tempstar only) Place Trim Strips (2) along the front side edge
of the door.
7.
Insert the two (2) screws into the screw holes located at the
front bottom of the door to install the door on the furnace.
Installation (Series C & D)
Model: N9MP1 Series C
1. Insert the two (2) screws into the screw holes located at the
front bottom of the door to install the door on the furnace.
Model: N9MP2, *9MPD, *9MPT, *9MPV
* Denotes Brand
(T9MPT, T9MPV only) Place Operating Instruction Label part
330712-201 below the sight glass on the inside of the door.
(See Figure 3)
2.
Place seal strips (2) along the side edge on the inside of the
door and trim to length.
3.
Place another seal strip along the bottom edge on the inside of
the door and trim to length.
4.
(Tempstar only) Insert Face Plate on the designated holes on
the front of the door.
5.
(Tempstar only) Insert Hole plugs (2).
6.
(Tempstar only) Place Trim Strips (2) along the front side edge
of the door.
7.
Insert the two (2) screws into the screw holes located at the
front bottom of the door to install the door on the furnace.
CUT HAZARD
Failure to follow this caution could results in bodily
injury.
Sheet metal parts may have sharp edges or burrs.
Use care and wear appropriate protective clothing
and gloves when handling parts.
If door screws from original door are not available, use 10-32 UNF
thread screws available at local hardware stores.
NOTE: If replacing front door with machine thread thumbscrews, drill
new door screw holes from 1/8" (3.2mm) diameter to 1/4" (6.4mm) di-
ameter before inserting thumbscrews. Use machine thread thumb-
screws from original (old) door. Discard black door screws included
with this kit.
Figure 3 IT9MPT, T9MPV, T9MVX
FACEPLATE / _OOR/ _oo_ ASSY
L
/
\ /
STRIP TRI_ _2}
NOTE: ON FRONT SIDE OR RLANS£
FLUSH A1BO1TON & OUT$[OE EOGE OR FLANGE
f
oPR #J
INST
J
/
441 06 1063 01 -2 -
Loading...