Page 1
INSTRUCTION MANUAL
•
Connector
body
CONNECTION CABLE
Thank you for purchasing this Icom product.
The OPC-2274
CONNECTION CABLE is used to connect a
repeater to the VE-PG3.
READ ALL INSTRUCTIONS carefully and completely before using the cable.
CONNECTING THE OPC-2274
Set the repeater channel, TX output power, and other necessary settings.
1
(See the repeater and the VE-PG3 instruction manuals for setting details.)
Turn OFF both the repeater and the VE-PG3, and then connect the OPC-2274, as shown below.
2
VE-PG3 (Rear view)
PHONE
LINE2
LINE1
Icom’s repeater
(IC-FR5000/IC-FR6000 series)
To [TRX1] (Upper slots)
ABC
ABC
The [TRX1] and [TRX2] ports (upper slots) accept the OPC-2274 connectors,
however, follow the example to correctly connect the repeater to ONLY the [TRX1] on the VE-PG3.
Be sure to insert the
connectors top side up.
1234
To p
OPC-2274
A
Bottom
To the accessory connector
CAUTION
• Verify that both the repeater and the VE-PG3 are turned OFF when connecting or disconnecting the cable.
• Hold the connector body when connecting or disconnecting them.
When other cables are connected, you can
use needle-nose pliers to carefully insert or
remove connectors.
Connector
Needle-nose pliersNeedle-nose pliers
Connector
body
body
VE-PG3 (Rear view)VE-PG3 (Rear view)
NEVER pull the connector by holding the
cable. This will damage the cable.
*If the cable becomes damaged, replace the
connector(s). See “REPLACING THE
CONNECTOR” on the reverse side for
replacement details.
• Never bend or pinch the cable.
• Never place a heavy object on the cable.
• Never touch the cable with wet hands.
• Always connect the cable correctly. An incorrect connection could damage the VE-PG3 and/or the repeater.
Page 2
REPLACING THE CONNECTOR
Connector
(Supplied with
the VE-PG3)
Orange
Blue
Yellow
Gray
White
VE-PG3 (Rear view)
Brown
Black
Green
Red
1234
If the cable becomes damaged, replace the connector(s). Make wire connections as described below.
• Spare connectors*
1
*
Manufacturer: DDK. Name: 232D-04S1B-DA5-FA (Equivalent to the OPC-2274 connector.)
1
are supplied with the VE-PG3.
The connector has two parts; a black base and a clear insert. DO NOT lock the connector parts before inserting all wires.
1
Insert the wires into the holes
according to the assigned pin
Press the clear insert down
2
until it locks in place.
numbers.
Connector
Connector
(Supplied with
(Supplied with
the VE-PG3)
the VE-PG3)
The wires for each hole are
assigned by color. See the
illustration below.
• After the insert is locked, it is
impossible to release it again.
OPC-2274 connection and wires assignment
• Turn OFF the VE-PG3 and the repeater before connecting or disconnecting the OPC-2274.
RECOMMENDATION
If reconnecting is repeated about 30 times,
cut the wires
*2 *
3
near
the connector and replace the connector.
*2 Remove the cable from the VE-PG3,
before cutting the wires.
3
*
DO NOT cut the wires too short. Other-
wise it will be difficult to reconnect them
to the VE-PG3.
VE-PG3 (Rear view)
VE-PG3 (Rear view)
To [TRX1] (Upper slots)
ABC
To the repeater
OPC-2274
LINE1
LINE2
PHONE
BCA
Connector top (Expanded view)
A
1234 1234 1234
OrangeOrange
BlueBlue
YellowYellow
WhiteWhite
B
GrayGray
C
BrownBrown
BlackBlack
GreenGreen
RedRed
• Follow the example to correctly connect the repeater to [TRX1] on the VE-PG3.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia and/or other countries.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7043X-1EX
Printed in Japan
© 2012 Icom Inc.
Loading...