ICOM CS-IP110H Instruction Manual

INSTRUCTION MANUAL

PROGRAMMING SOFTWARE

CS-IP110H

The CS-IP110H is an application software to setup the IP110H from your PC.
To use the software, a computer system and some items described in “System requirements” are required.

L The instructions are based on using Microsoft Windows 10.

Thank you for choosing this Icom product. READ
ALL INSTRUCTIONS carefully and completely

before using this product.

System requirements (As of December 2021)

• Operating System (OS)
Microsoft Windows 10 (32/64bit)
Microsoft Windows 8.1 (32/64bit)*

* Except for Microsoft Windows RT.

• USB port
A USB 1.1, 2.0 or 3.0 port

L Icom is not responsible for problems using a PC with

an OS other than one of the above installed.

• Cables

The USB cable supplied with the transceiver
or
OPC-478UC or OPC-478UC-1 programming cable

+ OPC-1655 programming adapter cable

NOTE for the OPC-478UC programming cable

Conrm your OPC-478UC has a “B” on its label.

Only the cables with a “B” are usable with Windows

8.1 and Windows 10.

Operation note

• The contents of this sheet, the software associated
with the CS-IP110H, and the appearance of the
CS-IP110H are all subject to change without notice.

• The displays, indications, or operations may differ
slightly, depending on your system settings, type of
OS, and its service pack level.

Procedure outline

To setup from a PC, rst follow the steps described below.

Step 1 Preparations

Conrm the system requirements in these instructions.

Step 2 CS-IP110H installation

Install the CS-IP110H following these instructions.

Step 3 USB driver installation

Install the USB driver following these instructions and the optional programming cable’s installation guide.

Step 4 Connection

Connect the transceiver and a PC following these instructions, and then turn ON the transceiver.

– 1 –

Installing the programming software

1. Sign in as an administrator.

L BE SURE no other applications are running.

2. Download and unzip the file.

L If “Security Warning” is displayed, click <Yes> to

continue.

3. Double-click “setup.exe” contained in the
unzipped folder.

Double-Click

L If “User Account Control” is displayed, click <Yes> to

continue.

4. “Welcome to the InstallShield Wizard for Icom
CS-IP110H #21” is displayed, and then click
<Next>>.

Click

L If your PC already has the software installed, the

uninstallation screen is displayed.

5. Click <Nex t >>.

6. After the installation is completed, “InstallShield
Wizard Complete” is displayed, and then click
<Finish>.

Click

Uninstalling the software

Before uninstalling the software, conrm the
CS-IP110H is closed.

1. Sign in as an administrator.

2. Click the <Start> button, then click the “Settings”
icon, and then click “Apps.”

• Microsoft Windows 8.1:
Place the mouse pointer in the bottom right corner of
the screen.
Click the “Settings” charm, then click “Control Panel,”
and then click “Uninstall a program.”

3. Click “Icom CS-IP110H #21,” and then click
“Uninstall.”

L If “User Account Control” is displayed, click <Yes> to

continue.

4. Follow the instructions on the screen to uninstall.

If you want to install the software in
a different location, click [Browse...]
then select a desired location on the
displayed screen.

Click

Reinstalling the software

Once the uninstallation is complete, you can reinstall
the CS-IP110H by following the steps in “Installing the
programming software.”

– 2 –

USB driver installation

D Connecting with the USB cable that

comes with the transceiver

Windows 10

When you connect the USB cable to a PC USB port,
the PC automatically installs the USB driver.

L An Internet connection is required for the USB driver

installation.

Windows 8.1

The USB driver is not supported by the automatic
recognition system. Download the driver from the
Icom website and manually install it.

NOTE:

• Sign in on the PC as an administrator.

• NEVER connect the USB cable between the
transceiver and the PC until the USB driver has
been installed. Disconnect the cable, if connected,
before starting the USB driver installation.

1. Confirm that the transceiver and the PC are not
connected, and no other application is running.

2. Extract the downloaded USB driver, and then
open the folder that contains the installer.

3. Double-click the following file:

• For the 32 bit version OS: setup32.exe

• For the 64 bit version OS: setup64.exe

L When the “User Account Control” dialog is

displayed, click <Yes>.

4. When the install screen is displayed, click
<Next>>.

5. When the “Ready to Install the Program” dialog is
displayed, click <Install>.

L If the “Windows Security” dialog is displayed, click

<Install>.

Click

• Windows starts installing the driver.

6. After the installation has completed, click
<Finish>.

Click

D Connecting with the programming cable

When you connect OPC-478UC-1 to a PC USB port,
the PC automatically installs the USB driver.

L An Internet connection is required for the USB driver

installation.

If the automatic USB driver installation is not
successful, or when you use the OPC-478UC,
download the driver from the Icom website and

Click

manually install it.

Downloading the driver:

Go to the Icom website. (https://www.icomjapan.com/support/)
In the “Firmware / Software”* menu, enter the model name and click the “Search” button to download the latest
USB driver.
* The menu name may be changed without notice.

– 3 –

Connection

L Before connecting or disconnecting the cables, turn OFF the transceiver.

1. Connect the USB cable that comes with the transceiver between the transceiver and the PC, as shown below.

L You can also program using the programming cable, the plug adapter cable, and the USB cable that comes with the

programming cable instead.

2. Turn ON the transceiver.

NOTE:

• Be sure to disconnect the transceiver from the charger and connect the USB cable while programming.

• If your PC does not recognize the USB cable, try to change the order in which you connect the cables.

Programming

L Use a coin or standard

screwdriver to protect

your ngernails.



adapter cable

OPC-1655

Programming cable

OPC-478UC-1 or OPC-478UC



Jack cap



To the USB
connector

Transceiver

Starting the CS-IP110H

1. Click “Icom CS-IP110H #21” in the Start menu to
start the software.

• Microsoft Windows 8.1:
<Start> ➔

L You can also start the software by simply double-

clicking the Icom CS-IP110H #21 short cut on the
desktop.

2. Edit necessary settings for each function.

TIP: See the Help le of the software for assistance

with the functions or settings.

To open the Help le, click “Contents” in the <Help>

menu of the software.
As of December 2021, the IP1000C and VE-PG4
can be used as the controller of the IP110H. In this
manual, and the Help le, the IP1000C and
VE-PG4 are written as “controller.”

➔ Icom CS-IP110H #21

USB cable

( comes with the

programming cable)

to a USB port

USB cable

(comes with the transceiver)

NOTE:

• To prevent data loss, you should rst read all the
transceiver’s setting data into the programming
software. Before editing or entering, make a

backup le onto your PC. A backup le enables

easy restoring even if the setting data in the
transceiver is accidentally deleted. After that,
enter or edit parameters using the programming
software. If you write the setting data into your
transceiver before reading, the settings are
overwritten.
See page 6 to read the data from the

transceiver settings and save the settings le.

• DO NOT turn OFF the transceiver or the PC, and
DO NOT disconnect the cable while reading or

writing setting data. Otherwise, the data could be
lost or deleted.

• If the VOX function* of the transceiver is set to
ON, programming with the programming cable is
not possible.
* The VOX function can be set on the controller.

PC

– 4 –

For your reference

D COM Port Searching

NOTE: Before searching for the COM port, con rm

the transceiver is turned ON and the transceiver and
the PC are correctly connected together.

Select “Search” in the <COM Port> menu to
automatically set the COM port number that the cable
is connected to.

L You can also check the COM port number in the

Device Manager screen.

To check the COM port number

For Windows 10

1. Right-click Windows icon, and then click
[Device Manager].

2 Click

1 Right-click

2. Double-click “Ports (COM & LPT)” on the “Device
Manager” screen.

Double-click

– 5 –

For your reference (Continued)

D COM Port Searching

To check the COM port number

For Windows 8.1

1. Click the folder icon on the taskbar.

Click

2. Right-click “This PC,” and then click “Properties.”

1 Right-click

D About the basic operation

To read the data from the transceiver

Click
menu.

To save the settings le to a folder on your PC

Click
menu.

, or select “Read ← TR” in the <Program>

or select “Save” or “Save As...” in the <File>

2 Click

3. Click [Device Manager].

• The “Device Manager” screen is displayed.

Click

4. Double-click “Ports (COM & LPT).”

Double-click

To write the setting data into the transceiver

Click

, or select “Write → TR” in the <Program>

menu.

– 6 –

For your reference (Continued)

D About the basic operation

Bluetooth Setting

You can conrm the Bluetooth connection settings

and the pairing list from the transceiver and the
programming software.
Click “Bluetooth Setting” in the <Program> menu to
open the window.

L See the CS-IP110H #21 Help for the details.

D Firmware updating

Basically, the IP110H rmware is automatically

updated through the controller.
See the transceiver’s Instruction manual for updating

the rmware.

If you need to update the transceiver’s rmware
ofine, select “Update...” in the <Firmware> menu.

L You cannot download the rmware le from the

Icom website. If the dealer orders you to update

the transceiver ofine, use the CS-IP110H to

update it.

NOTE:

• Before updating, conrm the transceiver is turned
ON and the transceiver and the PC are correctly
connected together.

• While updating, NEVER turn OFF the transceiver
or the PC, and NEVER disconnect the cables.

Otherwise, the transceiver rmware will be

corrupted.

CAUTION: Firmware is important for the basic
system control of your equipment. An interruption
or a malfunction during downloading may cause
a failure in the data rewriting, and your equipment
may stop functioning normally. If such a failure of

the rmware rewriting results in your equipment not

functioning normally, Icom Inc. expressly denies
any and all responsibility arising from the result of
damage from such an event.

Icom, Icom Inc., and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
Microsoft and Windows are trademarks of the Microsoft group of companies.
The Bluetooth
by Icom Inc. is under license.
All other products or brands are registered trademarks or trademarks of their respective holders.

®

word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Dec. 2021

– 7 –

A7663-1EX

© 2021 Icom Inc.