Page 1
CF-FR5000MT
CF CARD
Thank you for choosing the CF-FR5000MT CF CARD. The CF
card will upgrade your UC-FR5000
TROLLER and enable the Multi-Site Conventional/Trunking
mode use.
using the CF card.
Please read these instructions carefully before
TRUNKING/NETWORK CON-
DISPOSAL
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you that
in the European Union, all electrical and electronic products, batteries, and accumulators
(rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as
unsorted municipal waste. Dispose of them
according to the laws in your area.
ABOUT CE
The CF-FR5000MT complies with the essential
requirements of the 2014/30/EU directive for
Electromagnetic Compatibility and the 2001/95/
EC directive for General Product Safety.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany,
France, Spain, Russia, Australia, New Zealand, and/or other countries.
PRECAUTIONS
RWARNING! NEVER
when the repeater’s power is ON. Otherwise a fire, electric shock
may occur, or the data on the CF card may become corrupted.
CAUTION: DO NOT insert the CF card into the UC-FR5000 if
dust or dirt is on the connector. This may cause the CF card,
and the UC-FR5000, to malfunction.
CAUTION: DO NOT touch the connector part of the CF card
directly. It may cause a breakdown of the internal circuit by
static electricity.
CAUTION: DO NOT turn OFF the repeater while the data is
being transferred. Otherwise, the data on the CF card may become corrupted.
CAUTION: DO NOT use the CF card in a controller other than
the UC-FR5000. Inserting the CF card into other equipment
may corrupt the card’s data.
CAUTION: DO NOT keep the CF card in areas with extremely
high temperatures, high humidity, or in direct sunlight.
BE CAREFUL! DO NOT submerge the CF card in water, or
get it wet.
BE CAREFUL! DO NOT bend the CF card.
BE CAREFUL! DO NOT drop or strike the CF card against
another object.
insert the CF card into the UC-FR5000
Page 2
INSERTION AND REMOVAL
UPGRADE
• Insertion
Be sure to insert the CF card with the “CF-FR5000MT”
label (serial label) facing up.
Slowly insert the CF card into the CF card slot of the UCFR5000.
• If the CF card seems to jam, or is too tight, carefully remove
it. Ensure that the card is properly oriented and that there are
no obstructions in the sides of the card insertion slots, then
reinsert the card.
CF card slot
UC-FR5000
Serial label
CF card
• Removal
Hold the edge of the CF card, and slowly pull it out.
When no CF card is inserted, the UC-FR5000 cannot be
used for Multi-Site Conventional/Trunking mode operation,
even after the up
grade.
To upgrade the UC-FR5000, and enable the Multi-Site Conventional/Trunking mode, perform the following steps after inserting
the CF card. The following instructions are for reference only.
Please refer to the UC-FR5000’s help file for upgrade details.
q Access the setting screen of the UC-FR5000.
• The opening screen appears.
Refer to the UC-FR5000’s instruction manual for information on how to access the setting screen.
w Click “Maintenance” in the Top Menu.
• The Maintenance menu appears on the left side of the screen.
e Click “Application Add-on” in the Maintenance menu.
r Select “by on board CF card” in the Application Package,
then click [CHECK].
• The Application Package list appears.
t Select “idas_multisite_trunking_r300” from the list, then
click [Add].
• A confirmation screen appears.
Depends on the revision
y After carefully reading the warning text on the confirmation
screen, check the “Yes, I agree” box. Then click [Start].
• The installation starts to upgrade the firmware of the UC-FR5000.
“Now Adding, Please Wait...” appears during the installation.
u After the installation is complete, “Finish.” appears. Then
click [OK].
• The installed application appears on the Application list.
i Turn the repeater OFF, then turn it ON again.
• The upgrade process is now complete.
A6919W-1EX-2 © 2011–2020 Icom Inc.Jan 2020
Loading...