ERserver
IBM xSeries 225
Type 8647
Option Installation Guide
ER s e r v e r
IBM xSeries 225
Type 8647
Option Installation Guide
Note:
Before using this information and the product it supports, read the general information in “Notices”, on
page 49.
Second Edition (August 2003)
© Copyright International Business Machines Corporation 2003. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety ............................v
Chapter 1. Introduction ......................1
Related publications .......................1
Notices and statements used in this book ...............1
Major components of the xSeries 225 Type 8647 server ..........2
System-board option connectors ...................3
System-board internal connectors ..................3
System-board external connectors ..................4
System-board error LEDs .....................4
Chapter 2. Installing options....................7
Installation guidelines .......................7
System reliability considerations ..................7
Handling static-sensitive devices ..................8
Server power features .......................8
Turning on the server ......................8
Turning off the server ......................9
Removing the side cover .....................10
Removing the bezel .......................11
Removing and installing the support bracket ..............12
Working with adapters ......................13
Adapter considerations .....................13
Installing an adapter ......................14
Cabling an optional SCSI adapter .................17
Installing internal drives ......................18
Internal drive bays ......................18
Working with hot-swap drives ..................20
Installing non-hot-swap hard disk drives ...............22
Installing a 5.25-inch removable-media drive .............25
Power and signal cables for internal drives .............27
Installing memory modules ....................28
Installing an additional microprocessor ................29
Configuring the operating system .................30
Installing the additional microprocessor ...............31
Installing a security rope clip ....................34
Replacing a hot-swap power supply .................35
Replacing the battery ......................37
Completing the option installation ..................39
Replacing the bezel ......................39
Replacing the side cover ....................40
Updating your server configuration.................40
Connecting external options ....................41
Installing the server in a rack ....................41
Chapter 3. Input/output ports ...................43
Audio connectors ........................43
Line in ...........................44
Line out ..........................44
Microphone .........................44
Auxiliary-device (pointing-device) connector ..............44
Ethernet (RJ-45) connector ....................44
Keyboard connector .......................44
© Copyright IBM Corp. 2003 iii
Parallel connector ........................45
Serial connectors ........................45
Ultra320 SCSI connector .....................45
SCSI cabling requirements ...................46
Universal Serial Bus connectors ..................46
Video connector ........................47
Appendix. Notices .......................49
Edition notice .........................49
Trademarks ..........................50
Important notes.........................50
Product recycling and disposal ...................51
Electronic emission notices ....................51
Federal Communications Commission (FCC) statement .........51
Industry Canada Class A emission compliance statement ........52
Australia and New Zealand Class A statement ............52
United Kingdom telecommunications safety requirement.........52
European Union EMC Directive conformance statement .........52
Taiwanese Class A warning statement ...............53
Chinese Class A warning statement ................53
Japanese Voluntary Control Council for Interference (VCCI) statement . . . 53
Power cords ..........................53
Index ............................57
iv IBM xSeries 225 Type 8647: Option Installation Guide
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2003 v
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Statement 1:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical
storm.
v Connect all power cords to a properly wired and grounded electrical
outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal
cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached
devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
vi IBM xSeries 225 Type 8647: Option Installation Guide
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Statement 2:
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has
a module containing a lithium battery, replace it only with the same module
type made by the same manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3:
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.
v Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Safety vii
Statement 4:
≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5:
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.
2
1
viii IBM xSeries 225 Type 8647: Option Installation Guide
Statement 8:
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts inside
these components. If you suspect a problem with one of these parts, contact
a service technician.
Statement 12:
CAUTION:
The following label indicates a hot surface nearby.
Statement 13:
DANGER
Overloading a branch circuit is potentially a fire hazard and a shock hazard
under certain conditions. To avoid these hazards, ensure that your system
electrical requirements do not exceed branch circuit protection
requirements. Refer to the information that is provided with your device for
electrical specifications.
Safety ix
Statement 15:
CAUTION:
Make sure that the rack is secured properly to avoid tipping when the server
unit is extended.
Statement 23
CAUTION:
Do not place any object weighing more than 50 kg (110 lb) on top of rack-mounted
devices.
>50 kg (110 lb)
Declaración 23
PRECAUCIÓN:
No coloque ningún objeto que pese más de 50 kg (110 libras) encima de los
dispositivos montados en bastidor.
>50 kg (110 libras)
x IBM xSeries 225 Type 8647: Option Installation Guide
Hinweis 23
ACHTUNG:
Keine Gegenstände, die mehr als 50 kg wiegen, auf Rack-Einheiten ablegen.
>50 kg
Notice nø 23
ATTENTION:
Ne posez pas d’objet dont le poids dépasse 50 kg sur les unités montées en armoire.
>50 kg
Varningsmeddelande 23
VARNING:
Placera inte något föremål som väger mer än 50 kg ovanpå rackmonterade enheter.
>50 kg
Merknad 23
ADVARSEL:
Ikke sett gjenstander som veier mer enn 50 kg oppå enheter som er montert i et
kabinett.
>50 kg
Safety xi
Avviso 23
ATTENZIONE:
Non poggiare oggetti che pesano più di 50 kg sulla parte superiore delle unità montate
in rack.
>50 kg
Turvaohje 23
Varoitus:
Telineeseen asennettujen laitteiden päälle ei saa asettaa yli 50 kilon painoista esinettä.
>50 kg
Voorschrift 23
WAARSCHUWING:
Plaats geen objecten die meer dan 50 kg wegen op apparaten die in het rek zijn
gemonteerd.
>50 kg
Forskrift 23
Pas på!:
Anbring ikke genstande, der vejer mere end 50 kg, oven på enheder, der er monteret i
rack.
>50 kg
xii IBM xSeries 225 Type 8647: Option Installation Guide
Instrução 23
CUIDADO:
Não coloque nenhum objeto com peso superior a 50 kg (110 lbs.) sobre dispositivos
montados em rack.
>50 kg (110 lbs)
50
110
23
50
110
Safety xiii
50
23
50
23
50
23
·
50
50
110
50
110
xiv IBM xSeries 225 Type 8647: Option Installation Guide
23
> 50 Kg
23
50
50
110
50
110
50 110
50 110
23
Safety xv
50
23
50
23
50 110
50
50 110
110
23
50 110
xvi IBM xSeries 225 Type 8647: Option Installation Guide
50 110
23
23
50
5 0 110
5 0 110
Safety xvii
23
50 110
50 110
Instrução 23
CUIDADO:
Não coloque nenhum objeto com peso superior a 50 kg (110 lbs.) sobre dispositivos
montados em rack.
>50 kg (110 lbs)
WARNING: Handling the cord on this product or cords associated with accessories
sold with this product, will expose you to lead, a chemical known to the State of
California to cause cancer, and birth defects or other reproductive harm. Wash
hands after handling.
ADVERTENCIA: El contacto con el cable de este producto o con cables de
accesorios que se venden junto con este producto, pueden exponerle al plomo, un
elemento químico que en el estado de California de los Estados Unidos está
considerado como un causante de cancer y de defectos congénitos, además de
otros riesgos reproductivos. Lávese las manos después de usar el producto.
xviii IBM xSeries 225 Type 8647: Option Installation Guide
Chapter 1. Introduction
This Option Installation Guide contains instructions for installing, removing, and
connecting optional devices that your server supports.
Your server might have features that are not described in the documentation that
you received with the server. The documentation might be updated occasionally to
include information about those features, or technical updates might be available to
provide additional information that is not included in your server documentation.
These updates are available from the IBM Web site. Complete the following steps
to check for updated documentation and technical updates:
1. Go to http://www.ibm.com/pc/support/.
2. In the Learn section, click Online publications.
3. On the ″Online publications″ page, in the Brand field, select Servers.
4. In the Family field, select xSeries 225.
5. Click Display documents.
Related publications
In addition to this Option Installation Guide, the following documentation comes with
your server:
v User’s Guide
This publication is in Portable Document Format (PDF) on the IBM
Documentation CD. It contains general information about your server.
v Installation Guide
This printed publication contains instructions for setting up your server and basic
instructions for installing some options.
v Safety Information
This publication is in PDF on the IBM xSeries Documentation CD. It contains
translated caution and danger statements. Each caution and danger statement
that appears in the documentation has a number that you can use to locate the
corresponding statement in your language in the Safety Information book.
v Hardware Maintenance Manual and Troubleshooting Guide
This publication is in PDF on the IBM xSeries Documentation CD. It contains
information to help you solve problems yourself, and it contains information for
service technicians.
®
xSeries
™
Depending on your server model, additional publications might be included on the
IBM xSeries Documentation CD.
Notices and statements used in this book
The caution and danger statements that appear in this book are also in the
multilingual Safety Information book, which is on the IBM xSeries Documentation
CD. Each statement is numbered for reference to the corresponding statement in
the Safety Information book.
The following notices and statements are used in the documentation:
v Notes: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
© Copyright IBM Corp. 2003 1
v Attention: These notices indicate potential damage to programs, devices, or
data. An attention notice is placed just before the instruction or situation in which
damage could occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Major components of the xSeries 225 Type 8647 server
The orange color on components and labels in your server identifies hot-swap or
hot-plug components. You can install or remove these components while the server
is running, provided that the server is configured to support hot-swap and hot-plug
features. For complete details about installing or removing a hot-swap or hot-plug
component, see the information in Chapter 2, “Installing options”, on page 7.
The blue color on components and labels indicates touch points where a
component can be gripped, a latch moved, and so on.
The following illustration shows the major components in the server.
Note: The illustrations in this publication might differ slightly from your hardware.
Cover
Rear adapterretaining bracket
Adapter airflow
guide
Microprocessor
Heatsink
Memory module
Air baffle
Large hot-swap
drive cage
Frame-support bracket
EMC shield
Front adaptersupport bracket
Bezel
Filler
panels
Bezel
door
2 IBM xSeries 225 Type 8647: Option Installation Guide
System-board option connectors
The following illustration shows the system-board connectors for user-installable
options.
Microprocessor 1
(CPU1)
Microprocessor 2
(CPU2)
DIMM 1
DIMM 2
DIMM 3
DIMM 4
AGP Pro slot
PCI slot 1
(PCI1)
PCI-X slot 2
(PCI2)
PCI-X slot 3
(PCI3)
PCI-X slot 4
(PCI4)
PCI-X slot 5
(PCI5)
System-board internal connectors
The following illustration shows the internal connectors on the system board.
Rear fan 1
(SYSFAN1)
Rear fan 2
(SYSFAN2)
CD audio
(JCD1)
Main power
(POWER1)
PCI fan
(SYSFAN5)
Center fan
(SYSFAN4) - some models
Battery
Video
adapter
Mini-PCI
type III slot 6
(PCI6)
Remote Supervisor Adapter (JMGT1)
Diskette
drive (FDD1)
Powe r
(POWER2)
Wake-on-LAN
(JWL)
Secondary IDE
(IDE2)
Primary IDE
(IDE1)
Error LED
(JER2)
Cover switch
(JCI2)
Front panel
switch/LEDs
(JFP1)
SCSI
channel A
(SCSI1)
SCSI
channel B
(SCSI2)
SCSI LED
(J18)
Chapter 1. Introduction 3
System-board external connectors
The following illustration shows the external input/output port connectors on the
system board.
Mouse
Keyboard
USB 1/
USB 2
Parallel
(LPT1)
Serial A/
Serial B
(COMA/
COMB)
Ethernet
Audio
System-board error LEDs
Front panel USB (JUSB3)
The following illustration shows the LEDs on the system board. You might need to
refer to this illustration when solving problems with the server.
Diskette
drive (FDD1)
Rear fan 1
(SYSFAN1)
Rear fan 2
(SYSFAN2)
CD audio
(JCD1)
Main power
(POWER1)
PCI fan
(SYSFAN5)
Center fan
(SYSFAN4) - some models
Powe r
(POWER2)
Wake-on-LAN
(JWL)
Secondary IDE
(IDE2)
Primary IDE
(IDE1)
Error LED
(JER2)
Cover switch
(JCI2)
Front panel
switch/LEDs
(JFP1)
SCSI
channel A
(SCSI1)
SCSI
channel B
(SCSI2)
SCSI LED
(J18)
4 IBM xSeries 225 Type 8647: Option Installation Guide
Table 1. Error LEDs
Without optional Remote
Error LED
DIMM error (D26, D27, D28,
D29)
Supervisor Adapter
Memory problem (also turns
on system error LED on the
front bezel)
Microprocessor 2 error (D32) Microprocessor 2 problem
(also turns on system error
LED on the front bezel)
Fan error (D2, D19, D55,
No function Fan failure
D56)
Hard disk error (LEDs on
hot-swap hard disk drives)
Hot-swap hard disk drive
failure
With optional Remote
Supervisor Adapter
Memory problem (also turns
on system error LED on the
front bezel)
Microprocessor 2 problem
(also turns on system error
LED on the front bezel)
Hot-swap hard disk drive
failure
Chapter 1. Introduction 5
Loading...