IBM thinkpad pee schematic

IBM Mobile Systems

Hardware Maintenance Manual Volume 2: ThinkPad Computers

April 1995

We Want Your Comments! (Please see page 491)

S82G-1502-03

This Manual Supports:

ThinkPad 340x (2610) ThinkPad 355x (2619) ThinkPad 360x (2620) ThinkPad 370x (9545) ThinkPad 700x (9552) ThinkPad 701x (2630) ThinkPad 720x (9552) ThinkPad 750x (9545) ThinkPad 755x (9545)

IBM Mobile Systems

Hardware Maintenance Manual Volume 2: ThinkPad Computers

April 1995

We Want Your Comments! (Please see page 491)

S82G-1502-03

IBM

Note

Before using this information and the product it supports, be sure to read the general information under “Notices” on page 497.

Fourth Edition (April 1995)

The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL

BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time.

This publication was developed for products and services offered in the United States of America. IBM may not offer the products, services, or features discussed in this document in other countries, and the information is subject to change without notice. Consult your local IBM representative for information on the products, services, and features available in your area.

Requests for technical information about IBM products should be made to your IBM reseller or IBM marketing representative.

Note to U.S. Government users–Documentation related to Restricted rights–Use, duplication, or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

ii IBM Mobile Systems HMM

About This Manual

This manual contains service and reference information for IBM* ThinkPad* computer products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.

The manual is divided into sections as follows:

 The Introduction section provides general information,

guidelines, and safety information required to service computers.

 The majority of the manual consists of

product-specific sections that include service, reference, and product-specific parts information.

 The Common Devices Checkout section provides

procedures for testing the devices that are commonly attached to ThinkPad computers.

 The Miscellaneous Information section contains

information about acronyms, abbreviations, terms, and a telephone number listing.

Important

This manual is intended for trained servicers who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.

Before servicing an IBM mobile product, be sure to review the safety information under “Safety Notices (Multi-lingual Translations)” on page 7 and “Safety Information” on page 14.

Trademark of the IBM Corporation.

iii

Related Publications

The following mobile product publications are available through IBM or your IBM Authorized Dealer.

Publication Part, Form Number

Mobile Systems HMM Volume 1: Laptop, Notebook, Portable, and Thinkpad Computers

ThinkPad 700 (9552) HMS 42G2016, S42G-2016 ThinkPad 700 (9552) HMR 42G2015, S42G-2015 ThinkPad 700C (9552) HMS 42G2022, S42G-2022 ThinkPad 700C (9552) HMR 42G2021, S42G-2021 ThinkPad 720/720C (9552)

HMS ThinkPad 720/720C (9552)

HMR ThinkPad 730T (2524) HMM 82G5497, S82G-5497 ThinkPad Exp. Crtg. (3550)

HMS ThinkPad Exp. Crtg. (3550)

HMR PS/2 FaxConcentrator* HMS 15F2262, S15F-2262 PS/2 FaxConcentrator HMR 84F8541, S84F-8541 PS/2 Comm. Cartridge I

HMS PS/2 Comm. Cartridge I

HMR IBM High Speed Internal,

PCMCIA Data/Fax Modems

30H2356, S82G-1501-01

61G1193, S61G-1193

61G1187, S61G-1187

42G2338, S42G-2338

42G2339, S42G-2339

10G5993, S10G-5993

10G5992, S10G-5992

61G1556, S61G-1556

iv IBM Mobile Systems HMM

Obsolete Publications

This manual obsoletes the following publication:

Publication Part, Form Number

Mobile Systems HMM Volume 2: ThinkPad Computers

82G1502, S82G1502 19H1080, S82G1502

Related Diskettes

The following diskettes are available through IBM or your IBM Authorized Dealer.

Diskette Part, Form Number

ThinkPad 300 (2615) Advanced Diagnostics

ThinkPad 350, 350C, 425, 425C (2618) Advanced Diagnostics Diskette

ThinkPad 500 (2603) Adv. Diagnostics Diskette

ThinkPad 510 (2604) Adv. Diagnostics Diskette

ThinkPad 700 (9552) Reference Diskette

ThinkPad 700C (9552) Reference Diskette

ThinkPad 720/720C (9552) Reference Diskette

ThinkPad 750Ce (9545) Hardware Maintenance (for all Models 355x, 360x, 750x, and 755x)

ThinkPad Dock I (3545) 71G4140, S71G-4140 Docking Station (3550) 42G2428, S42G-2428 Data/Fax Modem 61G1556, S61G-1556 FaxConcentrator/A 84F8540, S84F-8540

33G9361, S33G-9361

A211000, GA21-1000

71G3702, S71G-3702

83G8095, S83G-8095

42G2017, S42G-2017

42G2023, S42G-2023

61G1194, S61G-1194

82G3891, S82G-3891

Trademark of the IBM Corporation.

vi IBM Mobile Systems HMM

Contents

Introduction . . . . . . . . . . . . . . . . . . . 1

Portable Computer Descriptions .......... 2

Drive and Diskette Compatibility Matrix ....... 4

Important Service Information ........... 5

Safety Notices (Multi-lingual Translations) ..... 7

Safety Information . . . . . . . . . . . . . . . . 14

Laser Compliance Statement ........... 19

Screw Size Chart ................. 20

ThinkPad 340x (IBM 2610) ............ 23

General Checkout . . . . . . . . . . . . . . . . . 25

Symptom-to-FRU Index . . . . . . . . . . . . . . 34

Related Service Procedures ............ 43

Product Overview . . . . . . . . . . . . . . . . . 48

FRU Removals and Replacements ......... 49

Locations . . . . . . . . . . . . . . . . . . . . . 59

Parts Listing . . . . . . . . . . . . . . . . . . . 62

ThinkPad 700, 700C, 720, 720C (9552) ...... 67

General Checkout . . . . . . . . . . . . . . . . . 68

Symptom-to-FRU Index . . . . . . . . . . . . . . 82

Related Service Procedures ............ 94

Product Overview . . . . . . . . . . . . . . . . 102

FRU Removals and Replacements ........ 104

Locations . . . . . . . . . . . . . . . . . . . . 110

Parts Listing (700) ............... 115

Parts Listing (720, 720C) ............ 118

ThinkPad 701C/701CS (2630) .......... 125

Checkout Guide . . . . . . . . . . . . . . . . 127

Symptom-to-FRU Index . . . . . . . . . . . . . 141

Related Service Procedures ........... 154

Product Overview . . . . . . . . . . . . . . . . 159

FRU Removals and Replacements ........ 161

Locations . . . . . . . . . . . . . . . . . . . . 181

Parts Listing . . . . . . . . . . . . . . . . . . 190

ThinkPad 355x, 360x, 370C, 750x, 755C, 755Cs . 195

Read This First ................. 197

General Checkout . . . . . . . . . . . . . . . . 200

Symptom-to-FRU Index . . . . . . . . . . . . . 216

Related Service Procedures ........... 228

Product Overview . . . . . . . . . . . . . . . . 232

FRU Removals and Replacements ........ 236

Removals Models 355x, 360x .......... 237

Removals Models 370C, 750x, 755C, 755Cs . . . 261

Locations . . . . . . . . . . . . . . . . . . . . 289

Parts Listing . . . . . . . . . . . . . . . . . . 296

ThinkPad 755CD, 755CDV (9545) ........ 315

General Checkout . . . . . . . . . . . . . . . . 317

 Copyright IBM Corp. 1995 vii

Symptom-to-FRU Index . . . . . . . . . . . . . 331

Related Service Procedures ........... 344

Product Overview . . . . . . . . . . . . . . . . 349

FRU Removals and Replacements ........ 350

Locations . . . . . . . . . . . . . . . . . . . . 381

Parts Listing . . . . . . . . . . . . . . . . . . 383

ThinkPad 755CE, 755CSE, 755CV, 755CX (9545) 391

General Checkout . . . . . . . . . . . . . . . . 393

Symptom-to-FRU Index . . . . . . . . . . . . . 408

Related Service Procedures ........... 420

Product Overview . . . . . . . . . . . . . . . . 424

FRU Removals and Replacements ........ 426

Locations . . . . . . . . . . . . . . . . . . . . 458

Parts Listing . . . . . . . . . . . . . . . . . . 460

Common Devices Checkout .......... 469

External Diskette Drive Test ........... 470

External Display Self-Test ............ 470

External Keyboard/Auxiliary Input Device Checkout 471

Fax/Modem Checkout . . . . . . . . . . . . . . 472

Printer Checkout . . . . . . . . . . . . . . . . 474

Port Replicator Checkout ............ 475

TrackPoint II Checkout ............. 476

TV Tuner . . . . . . . . . . . . . . . . . . . . 477

Common Parts Listing ............. 483

Miscellaneous Information . . . . . . . . . . . 489

Acronyms, Abbreviations and Terms ....... 489

Send Us Your Comments! ............ 491

Do You Need Technical References? ...... 492

Problem Determination Tips ........... 493

Phone Numbers, U.S. and Canada ........ 494

Notices . . . . . . . . . . . . . . . . . . . . . 497

viii IBM Mobile Systems HMM

Introduction

Portable Computer Descriptions .......... 2

Drive and Diskette Compatibility Matrix ....... 4

Important Service Information ........... 5

How to Use Error Messages .......... 6

How to Read POST Error Messages ...... 6

Safety Notices (Multi-lingual Translations) ..... 7

Safety Information . . . . . . . . . . . . . . . . 14

General Safety . . . . . . . . . . . . . . . . 14

Electrical Safety . . . . . . . . . . . . . . . . 15

Safety Inspection Guide ............ 16

Handling Electrostatic Discharge-Sensitive Devices 18

Grounding Requirements . . . . . . . . . . . . 18

Laser Compliance Statement ........... 19

Screw Size Chart ................. 20

 Copyright IBM Corp. 1995 1

Portable Computer Descriptions

All models in the following table have VGA video. Models N51, CL57, and P70/75 and Thinkpads 700x and 720x are Micro Channel* systems. All others are AT* bus systems.

Model Type Processor Memory Hrd Dsk

Model L40SX 8543-044 386SX-20 2M/18M 60M Model N45 SL 2614-065 386SL-25 2M/8M 80M

Model N51 SLC 8551-025 386SLC-16 2M/10M 80M Model N51 SX 8551-033 386SX-16 2M/10M 40M Model CL57 SX 8554-045 386SX-20 2M/16M 80M Model P70 386 8573-031 80386-16 2M/8M 30M

Model P75 486 8573-161 80486-33 8M/16M 160M

ThinkPad 300 2615-065 386SL-25 4M/12M 80M

ThinkPad 340 2610 486SLC2-50 4M/12M 125M ThinkPad 350 2618-AOE 486SL-25 4M/20M 85M

ThinkPad 350C 2618-NOA 486SL-25 4M/20M 125M

ThinkPad 355 2619 486SX-33 4M/16M 125M ThinkPad 355C 2619 486SX-33 4M/16M 125M

ThinkPad 355Cs 2619 486SX-33 2M/16M 170M

ThinkPad 360 2620 486SX-33 4M/16M 170M

ThinkPad 360C 2620 486SX-33 4M/16M 170M

ThinkPad 360Cs 2620 486SX-33 4M/16M 170M

ThinkPad 360Ce 2620 486DX2-50/25 4M/16M 170M

ThinkPad 360Cse 2620 486DX2-50/25 4M/16M 170M

ThinkPad 360P 2620 486SX-33 4M/16M 170M

ThinkPad 370C 9545 486DX4-75/25 4M/32M 340M

ThinkPad 500 2603-081 486SLC2-50/254M/12M 80M

ThinkPad 510 2604 486BLC2-50/254M/20M 200M ThinkPad 700 9552-300 486SLC-25 4M/16M 80M

ThinkPad 700C 9552-30B 486SLC-25 4M/16M 120M

C Color M Megabyte P Pen

2614-067 386SL-25 2M/8M 120M

8573-061 80386-20 2M/8M 60M 8573-121 80386-20 2M/8M 120M

8573-401 80486-33 8M/16M 400M

2615-067 386SL-25 4M/12M 120M

2618-JOA 486SL-25 4M/20M 125M 2618-LOA 486SL-25 4M/20M 250M

2618-POA 486SL-25 4M/20M 250M

2619 486SX-33 4M/16M 250M

2619 486SX-33 2M/16M 250M

2620 486SX-33 4M/16M 340M

2620 486DX2-50/25 4M/16M 340M 2620 486DX2-50/25 4M/16M 540M

2620 486SX-33 4M/16M 340M

9545 486DX4-75/25 4M/32M 540M 9545 486DX4-75/33 4M/32M 810M

2603-171 486SLC2-50/254M/12M 170M

9552-301 486SLC-25 4M/16M 120M

T Tablet TPF ThinkPad File

Trademark of the IBM Corporation.

2 IBM Mobile Systems HMM

Model Type Processor Memory Hrd Dsk

ThinkPad 701C 2630 486DX2-25/50 4M/32M 360MB

ThinkPad 701Cs 2630 486DX2-25/50 4M/32M 360MB

ThinkPad 710T 2523-09Y 486SLC2-25 4M/12M TPF

ThinkPad 720 9552-307 486SLC-25/50 4M/16M 120M

ThinkPad 720C 9552-30J 486SLC-25/50 4M/16M 160M ThinkPad 730T 2524 486SLC2-25 4M/12M 0M

ThinkPad 750 9545-006 486SL-33 4M/20M 170M

ThinkPad 750C 9545-306 486SL-33 4M/20M 170M

ThinkPad 750Ce 9545 P24S-50/25 4M/20M 340M ThinkPad 750Cs 9545 486SL-33 4M/20M 170M

ThinkPad 750P 9545-40C 486SL-33 4M/20M 170M

ThinkPad 755C 9545 486DX4-50/25 4M/32M 170M

ThinkPad 755CD 9545 486DX4-100/33 8M/32M 540M

ThinkPad 755CDV 9545 486DX4-100/33 8M/32M 540M

ThinkPad 755Ce 9545 486DX4-100/33 8M/32M 340M

ThinkPad 755Cs 9545 486DX4-50/25 8M/32M 170M

ThinkPad 755Cse 9545 486DX4-100/33 8M/32M 340M

ThinkPad 755CV 9545 486DX4-100/33 8M/32M 540M

C Color M Megabyte P Pen

2630 486DX2-25/50 4M/32M 540MB 2630 486DX4-25/75 8M/32M 360MB 2630 486DX4-25/75 8M/32M 540MB

2523-302 486SLC2-25 4M/12M 60M 2523-303 486SLC2-25 4M/12M 60M

9552-308 486SLC-25/50 4M/16M 160M

2524 486SLC2-25 4M/12M 60M

9545-008 486SL-33 4M/20M 340M

9545-308 486SL-33 4M/20M 340M

9545 486SL-33 4M/20M 340M

9545-40E 486SL-33 4M/20M 340M

9545 486DX4-50/25 4M/32M 340M 9545 486DX4-50/25 4M/32M 540M 9545 486DX4-75/25 4M/32M 170M 9545 486DX4-75/25 4M/32M 340M 9545 486DX4-75/25 4M/32M 540M

9545 486DX4-100/33 8M/32M 810M

9545 486DX4-100/33 8M/32M 540M 9545 486DX4-100/33 8M/32M 810M

9545 486DX4-50/25 8M/32M 340M 9545 486DX4-50/25 8M/32M 540M 9545 486DX4-75/25 8M/32M 170M 9545 486DX4-75/25 8M/32M 340M 9545 486DX4-75/25 8M/32M 540M

9545 486DX4-100/33 8M/32M 540M 9545 486DX4-100/33 8M/32M 810M

9545 486DX4-100/33 8M/32M 810M

T Tablet TPF ThinkPad File

Introduction 3

Drive and Diskette Compatibility Matrix

The following table provides identification information for

3.5-inch drives.

Diskette Drive

3.5-Inch - 1.44MB 1.44 on the eject button

3.5-Inch - 2.88MB 2.88 on the eject button

Identifying Mark

The following table provides compatibility information for

3.5-inch diskettes and 3.5-inch diskette drives.

Diskette Capacity

1.0MB Read/Write Read/Write

2.0MB Read/Write Read/Write

4.0MB Not Compatible Read/Write

1.44MB Drive

2.88MB Drive

The following table provides identification information for

5.25-inch diskette drives.

Diskette Drive

5.25-Inch - 360KB (External) Asterisk on bezel

5.25-Inch - 1.2MB (Internal) 1.2 on the eject button

Identifying Mark

The following table provides compatibility information for

5.25-inch diskettes and 5.25-inch diskette drives.

Diskette Capacity

360KB Read/Write Read/Write

1.2MB Not Compatible Read/Write

360KB Drive

1.2MB Drive

Note: A 360KB diskette written to or formatted on a

1.2MB drive can be read reliably only on a 1.2MB drive.

4IBM Mobile Systems HMM

Important Service Information

Important

Diskette fixes are customer installable. The diskette fixes are located on the PC Company Bulletin Board Service (BBS). The direct phone line for modem connection is 919-557-0001 or tieline 255-0001.

Advise customers to contact the PC Company HelpCenter at 800-772-2227 if they need assistance in obtaining or installing any diskette fixes.

Customers in Canada should call IBM HelpPC at 800-565-3344 for assistance or down-load information. The Canadian BBS phone numbers are:

Montreal 514-938-3022 Toronto 905-316-4255 Vancouver 604-664-6464 Winnipeg 204-934-2735

FRU Replacement Strategy

Before Replacing Parts

Ensure that all diskette fixes are installed prior to replacing any FRUs listed in this manual.

Use the following strategy to prevent unnecessary FRU replacement and service expense:

 If you are instructed to replace a FRU and that

does not correct the problem, reinstall the original FRU before you continue.

 Some computers have both a processor board and a

system board. If you are instructed to replace either the processor board or the system board, and the first board that you replaced does not correct the problem, reinstall the original board, then replace the other (processor or system) board.

 If an adapter or device consists of more than one

FRU, an error code may be caused by any of the FRUs. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms.

Warning: A customized setup configuration (other than default settings) may exist on the computer you are servicing. Running Automatic Configuration may alter those settings. Note the current configuration settings (using the View Configuration option) and verify that the settings are in place when service is complete.

Introduction

The advanced diagnostic tests are intended to test

only

IBM products. Non-IBM products or modified options can give false errors and invalid responses.

Hard Disk Drive Replacement Strategy:

Always try to run a low-level format before replacing a hard disk drive.

Warning: The drive startup sequence in the computer you are servicing might have been changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.

How to Use Error Messages

Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. The cause of the first error code can result in false error codes being displayed. If no error code is displayed, see if the error symptom is listed in the Symptom-to-FRU Index for the computer you are servicing.

How to Read POST Error Messages

POST error messages are displayed on the screen as three, four, five, or eight digits. The error messages that can be displayed as shorter POST messages are highlighted in this index. Some digits will represent different information for SCSI errors versus non-SCSI errors.

The following example shows which digits display the shorter POST error messages and also defines the SCSI information in an eight-digit error message.

Shorter POST Messages

┌────┬────┬────┬────┐

│ │ │ │ │ ┌────┬────┬────┬────┬────┬────┬────┬────┐ │ ð│ ð│ ð│ ð│ ð│ ð│ ð│ ð│ └────┴────┴────┴────┴────┴────┴────┴────┘

│ │ │ │ │ │ │ │

Reserved ││││││Size (SCSI)

└────┴────┘ │ │ Slot Number (SCSI)

ID (SCSI)

All SCSI devices are set to a different SCSI ID. Duplicate SCSI ID settings can generate a false error message. Use the SCSI ID to determine whether the error message is coming from an internal or an external device.

Device Code │ Logical Unit Number (SCSI)

6 IBM Mobile Systems HMM

Safety Notices (Multi-lingual Translations)

In this manual, safety notices appear in English with a page number reference to the appropriate multi-lingual, translated safety notice found in this section.

The following safety notices are provided in English, French, German, Italian, and Spanish languages.

Safety Notice 1

Before the computer is powered-on after FRU replacement, make sure all screws, springs, or other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.

Avant de remettre l'ordinateur sous tension après remplacement d'une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l'unité et assurez-vous qu'aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit.

Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder

-splitter können Kurzschlüsse erzeugen. Prima di accendere l'elaboratore dopo che é stata

effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all'interno dell'elaboratore. Verificare ciò scuotendo l'elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.

Introduction 7

Safety Notice 2

Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble it, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.

Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l'eau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de l'horloge temps réel, veillez à n'utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre feu ou d'exploser.

Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Bereitschafts- oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell'acqua né cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dell'RTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nell'appropriato Catalogo parti. L'impiego di una batteria non adatta potrebbe determinare l'incendio o l'esplosione della batteria stessa.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma.

8 IBM Mobile Systems HMM

Safety Notice 3

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery.

La batterie contient du nickel. Ne la démontez pas, ne l'exposez ni au feu ni à l'eau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n'utiliser que les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie inappropriée risque de prendre feu ou d'exploser.

Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o nell'acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nell'appropriato Catalogo parti. L'impiego di una batteria non adatta potrebbe determinare l'incendio o l'esplosione della batteria stessa.

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al sustituir la batería. La utilización de una batería no apropiada puede provocar la ignición o explosión de la misma.

Introduction 9

Safety Notice 4

The lithium battery can cause a fire, explosion, or severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.

La pile de sauvegarde contient du lithium. Elle présente des risques d'incendie, d'explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur polarisé et ne la démontez pas. Ne l'exposez pas à une temperature supérieure à 100°C, ne la faites pas brûler et n'en exposez pas le contenu à l'eau. Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile inappropriée risque de prendre feu ou d'exploser.

Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). L'impiego di una batteria non adatta potrebbe determinare l'incendio o l'esplosione della batteria stessa.

La bateria de repuesto es una bateria de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local.

10 IBM Mobile Systems HMM

Safety Notice 5

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.

Si le panneau d'affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.

Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht werden.

Nel caso che caso l'LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.

Introduction 11

Safety Notice 6

To avoid shock, do not remove the plastic cover that surrounds the lower portion of the inverter card.

Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d'alimentation.

Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida.

Safety Notice 7

Though main batteries have low voltage, a shorted or grounded battery can produce enough current to burn combustible materials or personnel.

Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d'une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.

Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.

12 IBM Mobile Systems HMM

Safety Notice 8

Before removing any FRU, power-off the computer, unplug all power cords from electrical outlets, remove the battery pack, then disconnect any interconnecting cables.

Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d'alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d'interface.

Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de conexión entre dispositivos.

Introduction 13

Safety Information

The following section contains the safety information that you need to be familiar with before servicing an IBM mobile computer.

General Safety

Follow these rules to ensure general safety:

 Observe good housekeeping in the area of the

machines during and after maintenance.

 When lifting any heavy object:

1. Ensure you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.

objects that weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.

 Do not perform any action that causes hazards to the

customer, or that makes the equipment unsafe.

 Before you start the machine, ensure that other

service representatives and the customer's personnel are not in a hazardous position.

 Place removed covers and other parts in a safe

place, away from all personnel, while you are servicing the machine.

 Keep your tool case away from walk areas so that

other people will not trip over it.

 Do not wear loose clothing that can be trapped in the

moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

 Insert the ends of your necktie or scarf inside clothing

or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.

 Do not wear jewelry, chains, metal-frame eyeglasses,

or metal fasteners for your clothing. Remember: Metal objects are good electrical

conductors.

 Wear safety glasses when you are: hammering,

drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

 After service, reinstall all safety shields, guards,

labels, and ground wires. Replace any safety device that is worn or defective.

 Reinstall all covers correctly before returning the

machine to the customer.

Do not attempt to lift any

14 IBM Mobile Systems HMM

Electrical Safety

Observe the following rules when working on electrical equipment.

Important

Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

 Find the room emergency power-off (EPO) switch,

disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

 Do not work alone under hazardous conditions or

near equipment that has hazardous voltages.

 Disconnect all power before:

– Performing a mechanical inspection – Working near power supplies – Removing or installing main units

 Before you start to work on the machine, unplug the

power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.

 If you need to work on a machine that has

electrical circuits, observe the following precautions:

– Ensure that another person, familiar with the

power-off controls, is near you. Remember: Another person must be there to

switch off the power, if necessary.

– Use only one hand when working with

powered-on electrical equipment; keep the other hand in your pocket or behind your back.

Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.

– When using testers, set the controls correctly

and use the approved probe leads and accessories for that tester.

– Stand on suitable rubber mats (obtained locally,

if necessary) to insulate you from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.

exposed

Introduction

 Regularly inspect and maintain your electrical hand

tools for safe operational condition.

 Do not use worn or broken tools and testers. 

Never assume

from a circuit. First, powered-off.

 Always look carefully for possible hazards in your

work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds.

 Do not touch live electrical circuits with the reflective

surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.

 Do not service the following parts

when they are removed from their normal operating places in a machine:

– Power supply units

– Pumps

– Blowers and fans

– Motor generators and similar units. (This practice ensures correct

grounding of the units.)

 If an electrical accident occurs:

– Use caution; do not become a victim

yourself.

– Switch off power. – Send another person to get medical aid.

that power has been disconnected

check

that it has been

with the power on

Safety Inspection Guide

The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

 Electrical hazards, especially primary power (primary

voltage on the frame can cause serious or fatal electrical shock).

 Explosive hazards, such as a damaged CRT face or

bulging capacitor

 Mechanical hazards, such as loose or missing

hardware

16 IBM Mobile Systems HMM

The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power-off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition.

Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and frame ground.

b. The power cord should be the appropriate type

as specified in the parts listings.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious non-IBM alterations. Use good judgment as to the safety of any non-IBM alterations.

6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Introduction

Handling Electrostatic Discharge-Sensitive Devices

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

 Keep the parts in protective packages until they are

inserted into the product.

 Avoid contact with other people.  Wear a grounded wrist strap against your skin to

eliminate static on your body.

 Prevent the part from touching your clothing. Most

clothing is insulative and retains a charge even when you are wearing a wrist strap.

 Use the black side of a grounded work mat to provide

a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

 Select a grounding system, such as those listed

below, to provide protection that meets the specific service requirement.

Note: The use of a grounding system is desirable

but not required to protect against ESD damage.

– Attach the ESD ground clip to any frame ground,

ground braid, or green-wire ground.

– Use an ESD common ground or reference point

when working on a double-insulated or battery-operated system. You can use coax or connector-outside shells on these systems.

– Use the round ground-prong of the AC plug on

AC-operated computers.

Grounding Requirements

Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.

18 IBM Mobile Systems HMM

Laser Compliance Statement

The CD-ROM drive in the ThinkPad computer is a laser product. The CD-ROM drive's classification label (shown below) is located on the drive.

CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 KLASSE 1 LASER APPARAT

The CD-ROM drive is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.

In other countries, the drive is certified to conform to the requirements of EN60825.

CAUTION: Do not open the drive; no user adjustments or serviceable parts are inside.

Class 1 laser products are not considered to be hazardous. The CD-ROM drive has an internal Class I (1),

0.5-milliwatt, aluminum gallium-arsenide laser that operates at a wavelength of 760 to 810 nanometers.

The design of the laser system and the CD-ROM drive ensures that there is no exposure to laser radiation above a Class 1 (1) level during normal operation, user maintenance, or servicing conditions.

Introduction

Screw Size Chart

Use the chart below to match the size and shape of the screws used in the computer you are servicing.

Silver

Black

Silver

Brass

Black

Brass

Silver

Brass

Silver

Black

Brass

20 IBM Mobile Systems HMM

+ 478 hidden pages