IBM SAN384B-2 Installation, Service And User Manual
IBM System Storage SAN384B-2
Installation, Service, and User Guide
Service information: 2499-416
Read Before Using
This product contains software that is licensed under written license agreements. Your use of such software is subject to
the license agreements under which they are provided.
GA32-0894-03
IBM System Storage SAN384B-2
Installation, Service, and User Guide
Service inf ormat ion: 2499-416
GA32-0894-03
Note:
Before using this information and the product it supports, read the information in “Notices” on page 145.
Portions Copyright © 2011, 2012 Brocade Communications Systems, Inc. All Rights Reserved.
The following paragraph does not apply to any country (or region) where such provisions are inconsistent with
local law.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states (or
regions) do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement
may not apply to you.
© Copyright IBM Corporation 2011, 2012.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Read this first
Summary of changes
|
|
|
|
|
|
|
|
Fourth edition
This is the fourth edition of the IBM System Storage SAN384B-2 Installation, Service,
and User Guide. The content changes since the last edition of this publication are
noted by a vertical line placed in the left margin beside each change. Minor edits
are not identified by this mark. A summary of the changes for each edition are
listed below.
The following changes were made in this edition:
v Addition of Enhanced 8 Gbps 32-port blade–Feature code 3633
v Addition of Enhanced 8 Gbps 48-port blade–Feature code 3649
v Addition of FIPS tamper-proof seals–Feature code 7230
v Enhanced inter-chassis link (ICL) capability–Feature code 7872
v Updated Fabric OS version to 7.0.1 or higher
Third edition
The following changes were made in this edition:
v Addition of FICON Accelerator and FICON with CUP Activation optional
features
v Updated FOS version to 7.0.0c
v Added port speed to Encryption blade information
Second edition
Getting help
The following changes were made in the second edition:
v The addition of 16 Gbps long wave length (LWL) SFP feature
v The addition of encryption, including the Encryption Blade (FS8-18)
v Updated instructions on ordering the lift tool load plate (now included with the
lift tool)
v Other minor content updates
For the latest version of your product documentation, visit the web at
www.ibm.com/shop/publications/order. Search by form number or title.
®
For more information about IBM
www.ibm.com/servers/storage/san/
®
IBM Redbooks
configurations, and more technical information. For redbooks associated with this
product, enter search terms on the following Web site: www.redbooks.ibm.com/.
For support information for this and other IBM products, see the IBM Support
Portal, www.ibm.com/supportportal. Search for the product Machine type or
product name.
often provide in depth information about product best practices,
SAN products, see the following Web site:
© Copyright IBM Corp. 2011, 2012 iii
For Fabric OS Release Notes and access to Fabric OS firmware downloads, go to
the IBM Support Portal, www.ibm.com/supportportal. Search for the product
Machine type or product name, and then follow links for Downloads. More
detailed instructions are available through the Accessing firmware updates and
OS documentation updates link on the product documentation CD that is shipped
with this product.
You can also contact IBM Service within the United States at 1-800-IBMSERV
(1-800-426-7378). For support outside the United States, you can find the service
number at: www.ibm.com/planetwide/.
To expedite your call, before contacting IBM Service, please have the following
information available:
v Machine type and model (2499-416)
v Product serial number
v License ID (you can use the licenseIdShow command to display the license ID)
v World Wide Name (WWN)
v FOS version installed
v Error numbers and messages received
v supportSave command output
v Detailed description of the problem and specific questions
v Description of any troubleshooting steps already performed and the results
v Serial console and Telnet session logs
v Syslog message logs
Visit www.ibm.com/contact for the contact information for your country or region.
For detailed information about the Fibre Channel standards, see the Fibre Channel
Industry Association (FCIA) Web site at: www.fibrechannel.org/
For information about storage industry standards, see the Storage Networking
Industry Association (SNIA) Web site at: www.snia.org/
Taiwan Contact Information
IBM Taiwan Product Service Contact Info:
IBM Taiwan Corporation
3F, No 7, Song Ren Rd., Taipei Taiwan
Tel: 0800-016-888
How to send your comments
Your feedback is important in helping us provide the most accurate and
high-quality information. If you have comments or suggestions for improving this
document, send us your comments by e-mail to starpubs@us.ibm.com . Be sure to
include the following:
v Exact publication title
v Publication form number (for example, GC26-1234-02)
f2c00790
iv SAN384B-2 Installation, Service, and User Guide
v Page, table, or illustration numbers
v A detailed description of any information that should be changed
Read this first v
vi SAN384B-2 Installation, Service, and User Guide
Contents
Read this first ............iii
Summary of changes ...........iii
Fourth edition ............iii
||
Third edition .............iii
Second edition ............iii
Getting help ..............iii
Taiwan Contact Information ........iv
How to send your comments ........iv
Figures ...............xi
Tables ...............xiii
Safety notices ...........xv
Safety notices and labels ..........xv
Danger notices ............xv
Caution notices ...........xviii
Safety labels .............xx
Attention notices ...........xxi
Rack safety ..............xxii
Rack installation ...........xxii
Rack relocation (19" rack) ........xxiii
Safety inspections ...........xxiv
Removing AC power .........xxiv
External machine checks ........xxiv
Internal machine checks ........xxiv
Product recycling and disposal .......xxv
About this document .......xxvii
Who should read this document ......xxvii
Product documents ...........xxvii
Brocade documents ...........xxvii
IBM and Brocade product matrix .....xxviii
Accessibility features for SAN384B-2 ....xxviii
Chapter 1. Introduction ........1
Overview of the SAN384B-2 .........1
Hardware components ...........2
SAN384B-2 blades ............5
High availability .............7
Reliability ...............8
Serviceability ..............8
Software features .............9
Security ...............9
Network Manageability .........10
Chapter 2. Installing a SAN384B-2 in a
cabinet...............11
Items included with the SAN384B-2 ......11
Ordering the lift tool ...........12
World trade locations ..........12
United States locations .........12
Installation guidelines ...........13
Installing a SAN384B-2 in a 2109 C36 cabinet . . . 14
Time required ............14
Unpacking and assembling the lift tool ....16
Unpacking the SAN384B-2 ........17
Installing the port-side exhaust kit ......18
Torque requirements ..........21
Installing the exhaust kit hardware .....21
Installing the SAN384B-2 into the cabinet . . . 25
Port numbering .............29
Chassis slots ..............31
Cable organization ............31
Chapter 3. Starting and configuring the
SAN384B-2 .............33
Providing power to the SAN384B-2 ......35
Connecting the SAN384B-2 and host with a serial
cable ................35
Logging in to the serial console port ......36
Configuring the IP addresses ........36
Logging off the serial console port and
disconnecting the serial cable .......38
Establishing an Ethernet connection ......38
Customizing the switch name ........38
Customizing a chassis name.........38
Setting the Domain ID...........39
Setting the date and time ..........39
Setting the date ............39
Setting the time zone ..........40
Synchronizing local time .........40
Verifying the persistent PID feature ......41
Determining installed software licenses .....41
Installing transceivers and attaching cables ....42
Managing cables.............44
Planning for encryption (optional).......45
Configuring for encryption (optional)......46
Summary of procedure .........46
Avoid double encryption .........47
Verifying correct operation and backing up the
configuration ..............47
Fabric OS firmware updates .........48
Downloading and installing firmware ....49
Powering off the SAN384B-2 ........49
Chapter 4. Monitoring system
components ............51
Port, application, or encryption blade status . . . 55
Control processor blade (CP8) status ......59
Core switch blade (CR16-4) status .......61
Power supply status ...........63
Blower assembly status ..........63
WWN card status ............65
Chapter 5. Removing and installing
components ............67
Removing and installing the chassis door ....67
© Copyright IBM Corp. 2011, 2012 vii
Time and items required .........67
Removing the chassis door ........67
Removing and installing cable management finger
assemblies ...............68
Time and items required .........68
Removing a cable management finger assembly 68
Installing a cable management finger assembly 69
Removing and installing port, application, and
encryption blades ............70
Time and items required .........70
Removing a port or application blade ....70
Installing a blade ...........72
Removing and installing blade filler panels ....72
Removing a filler panel .........72
Installing a filler panel..........73
Removing and installing a CP8 control processor
blade ................73
Time and items required .........74
Verifying the need for replacement .....74
Recording critical SAN384B-2 information . . . 75
Removing a control processor blade (CP8) . . . 76
Installing a control processor blade (CP8) . . . 77
Verifying operation of the new CP blade....78
Downloading firmware from an FTP server. . . 78
Downloading firmware from a USB device . . . 80
Completing the CP8 blade replacement ....81
Removing and installing a CR16-4 core switch blade 82
Verifying the necessity of replacement ....82
Time and items required .........82
Removing a CR16-4 core switch blade ....83
Installing a CR16-4 core switch blade .....83
Removing and installing a power supply ....84
Time and items required .........84
Removing a power supply ........84
Installing a power supply ........86
Removing and installing a blower assembly . . . 86
Time and items required .........86
Removing a blower assembly .......87
Installing a blower assembly........87
Removing and installing a WWN bezel and WWN
card.................88
Time and items required .........88
Verifying necessity of replacement ......88
Removing the WWN bezel and WWN card. . . 88
Installing the WWN bezel and WWN card . . . 89
Removing and installing transceivers ......89
Time required ............90
Items required ............90
Removing and installing an SFP+ optical
transceiver..............90
Removing and installing an mSFP optical
transceiver..............92
Removing and replacing inter-chassis link (QSFP)
cables ................93
Time and items required .........94
Removing an inter-chassis link (QSFP) cable . . 94
Installing an ICL cable ..........94
Possible ICL configurations ........95
Removing and replacing a SAN384B-2 chassis . . . 98
Time required ............99
Items required ............99
Verifying need for replacement .......99
Recording critical SAN384B-2 and SAN
information .............99
Disconnecting from the network and fabric . . 102
Removing components from the chassis . . . 103
Removing a SAN384B-2 from the cabinet . . . 104
Installing the replacement chassis .....105
Installing components into the new chassis . . 105
Downloading the configuration ......106
Verifying correct operation of system ....107
Reconnecting the system to the network and
fabric ...............108
Verifying correct configuration of the fabric . . 108
Cable routing table template .......110
Removing the batteries ..........111
Chapter 6. Installing new features . . 115
FC3632, FC3648- Installing a 16-Gb port blade (32
or 48 ports) ..............115
Time required ............115
Items required ............116
Procedures .............116
FC3633, FC3649- Installing an Enhanced 8-Gb port
|
blade (32 or 48 ports) ...........117
||
Time required ............117
||
Items required ............117
||
Procedures .............117
||
FC3864 - Installing an 8-Gb 64-port port blade . . 118
Time required ............118
Items required ............118
Procedures .............119
FC3890 - Installing an 8 Gbps Extension Blade
(FX8-24) ...............120
Time required ............120
Items required ............120
Procedures .............120
FC3895 - Installing an Encryption Blade (FS8-18) 121
Time required ............121
Items required ............122
Procedures .............122
Avoid double encryption ........123
FC7230 - Installing FIPS 140-2 Level 2 tamper proof
|
seals ................123
||
FC7871 - Installing a QSFP and inter-chassis license 123
Time required ............123
Items required ............123
Procedures .............123
FC7872 - Installing a QSFP and Enterprise
|
inter-chassis license ...........124
||
Time required ............124
||
Items required ............124
||
Procedures .............124
||
Appendix A. Product specifications 125
General specifications ..........125
System architecture ...........125
System size and weights..........127
System blade and FRU weights ......128
Facility requirements ...........128
Environmental requirements ........129
viii SAN384B-2 Installation, Service, and User Guide
Fibre Channel port specifications .......129
Power specifications ...........130
Data transmission ranges .........132
Powercords..............132
Appendix B. Application and
encryption blades .........133
FS8-18 blade..............133
FX8-24 blade .............133
Appendix C. Diagnostics and
troubleshooting ..........135
Obtaining chassis and component status ....135
Interpreting POST and boot results ......136
POST...............136
Boot ...............137
Diagnostics ..............137
Troubleshooting ............137
Appendix D. Port numbering .....141
Notices ..............145
Trademarks ..............146
Electronic emission notices .........146
Federal Communications Commission (FCC)
Class A Statement ...........146
Industry Canada Class A Emission Compliance
Statement .............147
Avis de conformité à la réglementation
d'Industrie Canada ..........147
European Union EMC Directive Conformance
Statement .............147
Germany Electromagnetic Compatibility
Directive ..............147
People's Republic of China Class A Electronic
Emission Statement ..........148
Japan Voluntary Control Council for Interference
(VCCI) Class A Statement ........149
Japan Electronics and Information Technology
Industries Association (JEITA) Statement . . . 149
Korea Communications Commission (KCC)
Class A Statement ...........149
Russia Electromagnetic Interference (EMI) Class
A Statement .............149
Australia and New Zealand Class A Statement 149
Taiwan Class A Electronic Emission Statement 150
Index ...............151
Contents ix
x SAN384B-2 Installation, Service, and User Guide
Figures
1. Port side of the SAN384B-2 (sample
configuration) ............3
2. Port side of the SAN384B-2 with the exhaust kit
installed (sample configuration) ......4
3. Blower (non-port) side of the SAN384B-2 5
4. Assembled lift tool with 24-inch load plate 17
5. Lift tool positioned next to the chassis on the
shipping tray ............18
6. Port-side exhaust kit assembly for 27 to 31 in.
(68.58 to 78.74 cm) cabinets .......20
7. Clip and retainer nut locations on exhaust side
cabinet rails (example showing relative
positions) .............22
8. Shelf installed in cabinet ........23
9. Air duct installed into side slot in shelf 23
10. Installing the top rail assembly to the duct
assembly and cabinet rails .......24
11. Lift tool and chassis positioned at rear of
cabinet ..............25
12. Load plate extended inside the cabinet to the
exhaust kit shelf ...........26
13. Chassis half way into cabinet on load plate 27
14. Location of screws to attach the chassis to the
cabinet rails ............28
15. Attaching the vertical cable management
finger assemblies to the cabinet rails ....29
16. Cable design for the mSFP patch cables for the
FC8-64 high density port blade ......32
17. Flow of configuration tasks for the SAN384B-2 34
18. Encryption configuration ........47
19. FC16-32 port blade ..........55
20. FC16-48 port blade ..........56
21. FC8-32E port blade ..........56
||
22. FC8-48E port blade ..........56
||
23. FC8-64 port blade ..........57
24. FS8-18 encryption blade ........57
25. FX8-24 extension blade.........58
26. Control processor blade (CP8) ports and LEDs 60
27. Core switch blade (CR16-4) .......61
28. Power supply ............63
29. Blower assembly LEDs .........64
30. WWN bezel ............66
31. Chassis door ............68
32. Cable management finger assemblies ....69
33. Port, application, and encryption blade
removal and installation (FC16-48 port blade
shown) ..............71
34. Filler panel removal and installation ....73
35. Removing the control processor (CP8) blade 77
36. Removing and replacing the core switch blade 83
37. Location of the two power supplies ....85
38. Removing and installing a power supply 86
39. Blower assembly removal and replacement 87
40. WWN bezel and card removal and installation 89
41. Optical transceiver (SFP+) extraction tool 90
42. Installing and removing a 16 Gbps SFP+ with
pull tab (shown without cable attached) . . . 91
43. Removing and replacing an SFP+ optical
transceiver .............91
44. Optical mSFP transceiver ........92
45. QSFP cable and transceiver .......94
46. QSFP cable and transceiver (bail open) 94
47. QSFP cable connections for two SAN768B-2
chassis (sample configuration) ......96
48. Core/edge ICL topology for SAN384B-2 and
|
||
|
||
||
||
||
SAN768B-2 chassis ..........97
49. full mesh ICL topology for SAN384B-2 and
SAN768B-2 chassis ..........98
50. Battery locations on the CP8 blade ....112
51. Encryption blade battery location .....113
52. CR16-4 core blade ..........141
53. FC16-32 port blade..........142
54. FC16-48 port blade..........142
55. FC8-32E port blade .........142
56. FC8-48E port blade .........143
57. FC8-64 port blade ..........143
58. FS8-18 encryption blade ........143
59. FX8-24 extension blade ........143
© Copyright IBM Corp. 2011, 2012 xi
xii SAN384B-2 Installation, Service, and User Guide
Tables
1. Brocade and IBM product and model
number matrix ..........xxviii
2. Blades available for the SAN384B-2 .....5
3. Installation tasks, time, and items required 15
4. Parts list for port-side exhaust kit for C36
cabinets ..............19
5. Torque requirements for mounting screws 21
6. Port and application blades available on the
SAN384B-2.............29
7. Configuration parameters ........36
8. Port, application, and encryption blade LED
descriptions ............58
9. CP blade LED descriptions .......60
10. CR16-4 blade LED descriptions ......62
11. Power supply LED descriptions ......63
12. Blower assembly LED descriptions .....64
13. Messages that may indicate WWN card failure 65
14. Steps for upgrading through multiple versions
of Fabric OS ............78
15. ICL connector port LEDs ........93
16. Critical information checklist example 100
17. Cable routing table for SAN384B-2 (64 ports
shown)..............110
18. General product specifications ......125
19. System architecture .........125
20. System sizes and weights .......127
21. System FRU weights .........128
22. Environmental requirements ......129
23. Power specifications .........130
24. Power demands per component .....131
||
25. Supported optics, speeds, cables, and
distances .............132
26. Environmental status and maintenance
commands ............136
27. Troubleshooting...........137
28. External port to slotShow port mapping for
|
||
CR16-4 core blades..........141
© Copyright IBM Corp. 2011, 2012 xiii
xiv SAN384B-2 Installation, Service, and User Guide
Safety notices
This section contains information about:
v “Safety notices and labels”
v “Rack safety” on page xxii
v “Safety inspections” on page xxiv
Safety notices and labels
When using this product, observe the danger, caution, and attention notices
contained in this guide. The notices are accompanied by symbols that represent the
severity of the safety condition. The danger and caution notices are listed in
numerical order based on their IDs, which are displayed in parentheses, for
example (D004), at the end of each notice. Use this ID to locate the translation of
|
|
these danger and caution notices in the IBM System Storage SAN b-type Safety
Notices publication, which is shipped with this product.
The following notices and statements are used in IBM documents. They are listed
below in order of increasing severity of potential hazards. Follow the links for
more detailed descriptions and examples of the danger, caution, and attention
notices in the sections that follow.
v Note: These notices provide important tips, guidance, or advice.
v “Attention notices” on page xxi: These notices indicate potential damage to
programs, devices, or data.
v “Caution notices” on page xviii: These statements indicate situations that can be
potentially hazardous to you.
v “Danger notices”: These statements indicate situations that can be potentially
lethal or extremely hazardous to you. Safety labels are also attached directly to
products to warn of these situations.
v In addition to these notices, “Safety labels” on page xx may be attached to the
product to warn of potential hazards.
Danger notices
A danger notice calls attention to a situation that is potentially lethal or extremely
hazardous to people. A lightning bolt symbol accompanies a danger notice to
represent a dangerous electrical condition. Read and comply with the following
danger notices before installing or servicing this device.
DANGER
To prevent a possible shock from touching two surfaces with
different protective ground (earth), use one hand, when possible, to
connect or disconnect signal cables. (D001)
© Copyright IBM Corp. 2011, 2012 xv
DANGER
Overloading a branch circuit is potentially a fire hazard and a
shock hazard under certain conditions. To avoid these hazards,
ensure that your system electrical requirements do not exceed
branch circuit protection requirements. Refer to the information
that is provided with your device or the power rating label for
electrical specifications. (D002)
DANGER
If the receptacle has a metal shell, do not touch the shell until you
have completed the voltage and grounding checks. Improper wiring
or grounding could place dangerous voltage on the metal shell. If
any of the conditions are not as described, STOP. Ensure the
improper voltage or impedance conditions are corrected before
proceeding. (D003)
DANGER
An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the devices that
attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent
an electrical shock. (D004)
A general electrical danger notice provides instructions on how to avoid shock
hazards when servicing equipment. Unless instructed otherwise, follow the
procedures in the following danger notice.
xvi SAN384B-2 Installation, Service, and User Guide
DANGER
When working on or around the system, observe the following
precautions:
Electrical voltage and current from power, telephone, and
communication cables are hazardous. To avoid a shock hazard:
v Connect power to this unit only with the IBM provided power
cord. Do not use the IBM provided power cord for any other
product.
v Do not open or service any power supply assembly.
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an
electrical storm.
v The product might be equipped with multiple power cords. To
remove all hazardous voltages, disconnect all power cords.
v Connect all power cords to a properly wired and grounded
electrical outlet. Ensure that the outlet supplies proper voltage
and phase rotation according to the system rating plate.
v Connect any equipment that will be attached to this product to
properly wired outlets.
v When possible, use one hand only to connect or disconnect
signal cables.
v Never turn on any equipment when there is evidence of fire,
water, or structural damage.
v Disconnect the attached power cords, telecommunications
systems, networks, and modems before you open the device
covers, unless instructed otherwise in the installation and
configuration procedures.
v Connect and disconnect cables as described below when
installing, moving, or opening covers on this product or attached
devices.
To Disconnect:
1. Turn off everything (unless instructed otherwise).
2. Remove the power cords from the outlets.
3. Remove the signal cables from the connectors.
4. Remove all cables from the devices.
To Connect:
1. Turn off everything (unless instructed otherwise).
2. Attach all cables to the devices.
3. Attach the signal cables to the connectors.
4. Attach the power cords to the outlets.
5. Turn on the devices.
(D005)
The weight of the SAN cabinet (2109-C36) with two SAN384B-2s is greater than
227 kg (500 lb), and has a fully loaded capacity of 816 kg (1795 lb). Under these
conditions, the following statement and notice apply.
Safety notices xvii
Delivery and subsequent transportation of the equipment
The customer should prepare his environment to accept the new product based on
the installation planning information provided, with assistance from an IBM
Installation Planning Representative (IPR) or IBM authorized service provider. In
anticipation of the equipment delivery, the final installation site should be prepared
in advance such that professional movers/riggers can transport the equipment to
the final installation site within the computer room. If for some reason, this is not
possible at the time of delivery, the customer will need to make arrangements to
have professional movers/riggers return to finish the transportation at a later date.
Only professional movers/riggers should transport the equipment. The IBM
authorized service provider will only perform minimal frame repositioning within
the computer room, as needed, to perform required service actions. The customer
is also responsible for using professional movers/riggers in the case of equipment
relocation or disposal.
>(>)500 lbs. 227 kg.
Caution notices
A caution notice calls attention to a situation that is potentially hazardous to
people because of some existing condition. A caution notice can be accompanied
by different symbols, as in the examples below:
DANGER
Heavy equipment—personal injury or equipment damage might
result if mishandled. (D006)
a69i0333
If the symbol
is... It means....
A hazardous electrical condition with less severity than electrical danger.
A generally hazardous condition not represented by other safety
symbols.
A specification of product weight that requires safe lifting practices. The
weight range of the product is listed below the graphic, and the wording
of the caution varies, depending on the weight of the device.
55 kg ( 121.2 lbs)
svc00169
>55kg (121.2 lb)
A potential hazard of pinching the hand or other body parts between
parts.
P/N 18P5850-B
SJ000752
A hazardous condition due to moving parts nearby.
A hazardous condition due to the use of a laser in the product. Laser
symbols are always accompanied by the classification of the laser as
defined by the U.S. Department of Health and Human Services (for
example, Class I, Class II, and so forth).
xviii SAN384B-2 Installation, Service, and User Guide
Read and comply with the following caution notices before installing or servicing
this device.
CAUTION:
Energy hazard present. Shorting may result in system outage and
possible physical injury. Remove all metallic jewelry before servicing.
(C001)
CAUTION:
The weight of this part or unit is more than 55 kg (121.2 lb). It takes
specially trained persons, a lifting device, or both to safely lift this
55 kg ( 121.2 lbs)
>55kg (121.2 lb)
part or unit. (C011)
svc00169
CAUTION:
The system contains circuit cards, assemblies, or both that may contain
lead solder. To avoid the release of lead (Pb) into the environment, do
not burn. Discard the circuit card as instructed by local regulations.
(C014)
CAUTION:
This product is equipped with a 3-wire (two conductors and ground)
power cable and plug. Use this power cable with a properly grounded
electrical outlet to avoid electrical shock. (C018)
CAUTION:
This product might contain one or more of the following devices:
CD-ROM drive, DVD-ROM drive, DVD-RAM drive, or laser module,
which are Class 1 laser products. Note the following information:
v Do not remove the covers. Removing the covers of the laser product
could result in exposure to hazardous laser radiation. There are no
serviceable parts inside the device.
v Use of the controls or adjustments or performance of procedures
other than those specified herein might result in hazardous
radiation exposure.
(C026)
CAUTION:
The power-control button on the device does not turn off the electrical
current supplied to the device. The device might also have more than
one connection to dc power. To remove all electrical current from the
device, ensure that all connections to dc power are disconnected at the
dc power input terminals. (C031)
CAUTION:
Servicing of this product or unit is to be performed by trained service
personnel only. (C032)
Safety notices xix
CAUTION:
For CA residents only: IBM recommends installing this product in a room size
of 62 cubic meters (2190 cubic feet) or larger at 0.4 ACH ventilation rate to
reduce the concentrations of any chemicals emitted by the product.
Safety labels
As an added precaution, safety labels are often installed directly on products or
product components to warn of potential hazards. These can be either danger or
caution notices, depending upon the level of the hazard.
The actual product safety labels may differ from these sample safety labels:
DANGER
Hazardous voltage, current, or energy levels are present inside
any component that has this label attached. Do not open any
cover or barrier that contains this label. (L001)
DANGER
Rack-mounted devices are not to be used as a shelf or work space.
(L002)
DANGER
Multiple power cords. The product might be equipped with
multiple power cords. To remove all hazardous voltages,
disconnect all power cords. (L003)
DANGER
Hazardous voltage present. Voltages present constitute a shock
hazard, which can cause severe injury or death. (L004)
CAUTION:
Hazardous energy present. Voltages with hazardous energy might
cause heating when shorted with metal, which might result in
splattered metal, burns, or both. (L005)
CAUTION:
Hazardous moving parts nearby (L008)
xx SAN384B-2 Installation, Service, and User Guide
P/N 18P5850-B
SJ000752
Attention notices
An attention notice indicates the possibility of damage to a program, device, or
system, or to data. An exclamation point symbol may accompany an attention
notice, but is not required. A sample attention notice follows:
Attention: Do not bend a fibre cable to a radius less than 5 cm (2 in.); you can
damage the cable. Tie wraps are not recommended for optical cables because they
can be easily overtightened, causing damage to the cable.
ESD precautions
Attention: Many of the field replaceable units (FRUs) are sensitive to electrostatic
discharge (ESD), and can potentially be damaged by improper handling. Wear a
wrist grounding strap connected to chassis ground (if the SAN384B-2 is plugged
in) or a bench ground. Store all ESD-sensitive components in antistatic packaging.
CAUTION:
Pinch hazard. (L012)
Safety notices xxi
Rack safety
Rack installation
DANGER
Observe the following precautions when working on or around your IT rack system:
v Heavy equipment—personal injury or equipment damage might result if
mishandled.
v Always lower the leveling pads on the rack cabinet.
v Always install stabilizer brackets on the rack cabinet.
v To avoid hazardous conditions due to uneven mechanical loading, always install the
heaviest devices in the bottom of the rack cabinet. Always install servers and
optional devices starting from the bottom of the rack cabinet.
v Rack-mounted devices are not to be used as shelves or work spaces. Do not place
objects on top of rack-mounted devices.
v Each rack cabinet might have more than one power cord. Be sure to disconnect all
power cords in the rack cabinet when directed to disconnect power during servicing.
v Connect all devices installed in a rack cabinet to power devices installed in the
same rack cabinet. Do not plug a power cord from a device installed in one rack
cabinet into a power device installed in a different rack cabinet.
v An electrical outlet that is not correctly wired could place hazardous voltage on the
metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock.
(R001 part 1 of 2)
CAUTION:
v Do not install a unit in a rack where the internal rack ambient temperatures will
exceed the manufacturer’s recommended ambient temperature for all your
rack-mounted devices.
v Do not install a unit in a rack where the air flow is compromised. Ensure that air flow
is not blocked or reduced on any side, front, or back of a unit used for air flow
through the unit.
v Consideration should be given to the connection of the equipment to the supply circuit
so that overloading of the circuits does not compromise the supply wiring or
overcurrent protection. To provide the correct power connection to a rack, refer to the
rating labels located on the equipment in the rack to determine the total power
requirement of the supply circuit.
v (For sliding drawers) Do not pull out or install any drawer or feature if the rack stabilizer
brackets are not attached to the rack. Do not pull out more than one drawer at a time.
The rack might become unstable if you pull out more than one drawer at a time.
v (For fixed drawers) This drawer is a fixed drawer and must not be moved for servicing
unless specified by the manufacturer. Attempting to move the drawer partially or
completely out of the rack might cause the rack to become unstable or cause the
drawer to fall out of the rack.
(R001 part 2 of 2)
xxii SAN384B-2 Installation, Service, and User Guide
Rack relocation (19" rack)
CAUTION:
Removing components from the upper positions in the rack cabinet improves
rack stability during relocation. Follow these general guidelines whenever you
relocate a populated rack cabinet within a room or building:
v Reduce the weight of the rack cabinet by removing equipment starting at the
top of the rack cabinet. When possible, restore the rack cabinet to the
configuration of the rack cabinet as you received it. If this configuration is not
known, you must do the following:
– Remove all devices in the 32U position and above.
– Ensure that the heaviest devices are installed in the bottom of the rack
cabinet.
– Ensure that there are no empty U-levels between devices installed in the
rack cabinet below the 32U level.
– If the rack cabinet you are relocating is part of a suite of rack cabinets,
detach the rack cabinet from the suite.
– Inspect the route that you plan to take when moving the rack to eliminate
potential hazards.
– Verify that the route that you choose can support the weight of the loaded
rack cabinet. Refer to the documentation that came with your rack cabinet
for the weight of a loaded rack cabinet.
– Verify that all door openings are at least 760 x 2030 mm (30 x 80 in.).
– Ensure that all devices, shelves, drawers, doors, and cables are secure.
– Ensure that the four leveling pads are raised to their highest position.
– Ensure that there is no stabilizer bracket installed on the rack cabinet
during movement.
– Do not use a ramp inclined at more than 10 degrees.
– Once the rack cabinet is in the new location, do the following:
- Lower the four leveling pads.
- Install stabilizer brackets on the rack cabinet.
- If you removed any devices from the rack cabinet, repopulate the rack
cabinet from the lowest position to the highest position.
– If a long distance relocation is required, restore the rack cabinet to the
configuration of the rack cabinet as you received it. Pack the rack cabinet in
the original packaging material, or equivalent. Also, lower the leveling
pads to raise the casters off of the pallet and bolt the rack cabinet to the
pallet.
(R002)
Safety notices xxiii
Safety inspections
Perform the following safety checks to identify unsafe conditions. Be cautious of
potential safety hazards that are not covered in the safety checks. If unsafe
conditions are present, determine how serious the hazards are and whether you
should continue before you correct the problem.
Removing AC power
Perform the following steps to remove the alternating current (ac) power:
1. Perform a controlled system shutdown.
2. Set the power switch on the product to the off position.
3. Disconnect the power cables from the power source.
External machine checks
Perform the following external machine checks:
1. Verify that all external covers are present and are not damaged.
2. Ensure that all latches and hinges are in correct operating condition.
3. Check the power cable for damage.
4. Check the external signal cable for damage.
5. Check the cover for sharp edges, damage, or alterations that expose the internal
6. Check that any unused serial ports are covered for dust and ESD protection.
7. Correct any problems that you find.
DANGER
Multiple power cords. (L003)
parts of the device.
The cover should be kept on the serial port whenever it is not being used.
Internal machine checks
Perform the following internal machine checks:
1. Check for any non-IBM changes that might have been made to the machine. If
any are present, obtain the “Non-IBM Alteration Attachment Survey” form,
number R009, from the IBM branch office. Complete the form and return it to
the branch office.
2. Check the condition of the inside of the machine for:
v Metal or other contaminants
v Indications of water or other fluid
v Fire or smoke damage
3. Check for any obvious mechanical problems, such as loose components.
4. Check any exposed cables and connectors for wear, cracks, or pinching.
xxiv SAN384B-2 Installation, Service, and User Guide
Product recycling and disposal
Refer to the IBM Systems Environmental Notices and User Guide (Z125-5823) on the
CD shipped with the product for translated environmental statements and
information regarding product recycling and disposal. This document may be
provided either in printed version or on a CD-ROM. See “Removing the batteries”
on page 111 for battery removal instructions, if needed to meet environmental
regulations.
Safety notices xxv
xxvi SAN384B-2 Installation, Service, and User Guide
About this document
This document describes how to install and service the IBM System Storage
SAN384B-2 fabric backbone product (Machine type 2499-416). Throughout this
document, the product is referred to as the SAN384B-2, or more generically as
system, device,orchassis, where appropriate. This document includes information
|
|
specific to the SAN384B-2 running Fabric OS version 7.0.1 and later. For
information about a Fabric OS version other than 7.0.1, refer to the documentation
specific to your Fabric OS version.
The sections that follow provide information about:
v “Who should read this document”
v “Product documents”
v “Brocade documents”
v “Accessibility features for SAN384B-2” on page xxviii
Who should read this document
This document is intended for trained service representatives who are responsible
for installing and servicing the SAN384B-2, and for network administrators
responsible for maintaining and using the SAN384B-2.
Product documents
The following documents contain information related to this product. The
documentation may be printed material, on the documentation CD that is shipped
with the product, or available on the web through the IBM Support Portal or IBM
Publications Center.
v IBM System Storage SAN384B-2 Installation, Service, and User Guide, GA32-0894
(this document, which is also available in accessible HTML format on the
documentation CD)
v IBM System Storage SAN b-type Safety Notices
v IBM Systems Environmental Notices and User Guide, Z125-5823
v IBM Warranty
v Implementing an IBM/Brocade SAN with 8 Gbps Directors and Switches, (an IBM
Redbook), SG24-6116
®
Note: This publication was written for earlier products, but many of the
practices still apply.
|
|
v IBM System Storage FIPS 140-2 Security Seal Application Procedures (GA32-2220-00),
available online only for this optional feature.
Brocade documents
IBM switches and directors use software licensed from Brocade Communications
Systems, Inc. You can find information related to the software that supports the
SAN384B-2 in the following documents on the CD-ROM supplied with this
product. More recent versions of the Fabric Operating System (FOS) documentation
may be available to match the version of FOS that you have installed. The
© Copyright IBM Corp. 2011, 2012 xxvii
publication CD includes information on how to locate and download the latest
versions of FOS documentation and firmware updates.
Brocade Fabric OS
v Fabric OS Administrator's Guide
v Fabric OS Command Reference Manual
v Fabric OS MIB Reference
v Fabric OS Message Reference
v Fabric OS Troubleshooting and Diagnostics Guide
v Fabric OS FCIP Administrator's Guide
v Fabric OS Encryption Administrator’s Guide Supporting Tivoli Key Lifecycle Manager
(TKLM) Environments
v FICON Administrator's Guide
Brocade Fabric OS optional features
v Fabric Watch Administrator's Guide
v Web Tools Administrator's Guide
IBM and Brocade product matrix
When you use any of the Brocade documents, such as Fabric Operating System
(FOS) publications, you will notice that the model numbers reflect the
corresponding Brocade products. Table 1 provides a product matrix for you to use
to correlate the Brocade products and models to the IBM product names and
machine types and model numbers. Products withdrawn from marketing are not
listed.
Table 1. Brocade and IBM product and model number matrix
Brocade product name IBM product name
Brocade 6505 SAN24B-5 2498 Model F24, 249824G
Brocade 6510 SAN48B-5 2498 Model F48
Brocade DCX 8510-4 SAN384B-2 2499 Model 416
Brocade DCX 8510-8 SAN768B-2 2499 Model 816
Brocade DCX-4S SAN384B 2499 Model 192
Brocade DCX SAN768B 2499 Model 384
Brocade Encryption Switch SAN32B-E4 2498 Model E32
Brocade 8000 IBM Converged Switch B32 3758 Models B32 and L32
Brocade 7800 SAN06B-R 2498 Model R06
Brocade 5300 SAN80B-4 2498 Model B80
Brocade 5100 SAN40B-4 2498 Models B40 and 40E
Brocade 300 SAN24B-4 2498 Models B24 and 24E
Accessibility features for SAN384B-2
Accessibility features help users who have a disability, such as restricted mobility
or limited vision, to use information technology products successfully.
IBM machine type and
model number
xxviii SAN384B-2 Installation, Service, and User Guide
Loading...