IBM IC35L036UWPR15, IC35L036UCPR15, IC35L018UWPR15, IC35L018UCPR15 Quick Installation Guide

Address 7 is normally reserved for the host adapter

Reserved

N

Disable Unit Attention

M

Target Initiated Sync Negotiation

L

Disable Parity

K

Delay Start 6/12

J

Auto Start Delay

I

(80-pin model) Disable Auto Spin

Force Single-ended Mode

C

Termination Power (68-pin model only)

B

Pin pair for LED connection

A

IC35L018UCPR15

IC35L018UWPR15

IBM storage products

Quick installation guide

Ultrastar 36Z15

Ultra 160 SCSI

Models:

IC35L036UWPR15
IC35L036UCPR15

Handling precautions

Ÿ Do not open the electrostatic discharge (ESD) bag

containing the drive until required.

Ÿ Do not apply pressure on the drive during handling

or installation.

Ÿ To prevent damage from impact or vibration

always set the drive down gently.

Ÿ Handle the drive carefully by the edges. Do not

touch the exposed printed circuit board or any
electronic components.

Ÿ Do not cover the breather hole! Covering the

breather hole may result in loss of data.

Ÿ Save the packaging materials including the ESD

bag in the event that the drive must be returned.

Installing the drive

Address jumper and drive option blocks

1. Backup all data.

2. Record the serial number and part number of your
hard drive for future reference.

3. Turn off the computer and remove the computer
system cover.

4. Before handling the hard disk drive, discharge any
static electricity from yourself and your clothing.
With one hand touch an unpainted metal surface
on the computer chassis, then touch the ESD bag
with the other hand for a minimum of two seconds.

5. Remove the hard drive from the ESD bag.

6. Unplug the computer.

7. Assign a SCSI address (0 through 15) to the drive
by installing a jumper on the appropriate ID bits
(pin pairs D, E, F, and G) on jumper block J4 as
shown on the shaded area in the following
illustration.

Address 6 is the shipping default for 68-pin models

IBM Technology Group Support Center version 1.0

8. Select the desired options by placing a jumper on
the pin pair for that option. The options are listed
below cross-referenced by a letter to the two
jumper blocks in the above illustration. Refer to
the Ultrastar 36Z15 product summary for a
description of the options.

(68-pin model) Enable Auto Spin

H

Page 1

IBM storage products

SPECIAL NOTES:

Ÿ For this drive to operate in LVD mode all SCSI

devices including the SCSI bus host adapter must
be LVD devices.

Ÿ The drive is designed to detect if the SCSI bus is

LVD or SE. The drive will function based upon the
mode that it detects. If for some reason the drive
cannot detect an SE mode bus, place a jumper on
pins 5 & 6 of jumper block J-4 to force SE mode.

Ÿ On 68-pin drives termination power must be

provided. In most cases it is provided by the host
adapter. If it is not, install a jumper on pins 3 & 4
of jumper block J-4 to enable termination power.
See the illustration above. (The 80-pin drive does
not provide termination power.)

9. For a 68-pin drive attach the power cable and en­sure that one end of the SCSI cable is connected
to the host adapter. Attach a terminator to the end
of the SCSI cable furthest from the host adapter. If
the drive is the only device on the SCSI cable,
attach it to the cable connector closest to the ter­minator. Additional drives may be attached to any
unused connector. (The 80-pin drive is plugged
into server backplanes and requires no cables.)

10.Using the appropriate brackets or rails, mount the
drive with any of its six surfaces facing down.
Retrieve any loose screws or parts from within the
computer.

11.Ensure that cables are properly routed.

12.Plug in your computer. Do not turn it on.

13.Insert the operating system (OS) setup diskette
into the floppy drive.

14.Turn on your computer.

Ÿ If the system boots up, turn off your computer

and replace the cover.

Ÿ If your system does not boot up, turn off your

computer and check all connections and set­tings. Turn on and boot the system.

Ÿ If the system still fails to boot up, turn off your

computer and remove the new drive to return
the system to its original configuration. Contact
the IBM Technology Group Support Center.

Partitioning and formatting (using DOS 5.0 or later)

CAUTION: Partitioning and formatting will destroy any
previous data. When partitioning and formatting a drive
in a system with more than one drive be sure that you
select the correct hard drive.

1. With the OS setup diskette inserted in the floppy
drive, turn on the computer.

2. At the DOS prompt type FDISK, press ENTER,
and follow the instructions on the screen.

3. To format the primary system drive, type
FORMAT C:/S at the DOS command prompt and
press ENTER. The /S parameter makes C: the
startup drive of the operating system.

4. To format a second drive (not C:), type
FORMAT X: (where X is the drive letter assigned
by FDISK) at the DOS prompt and press ENTER.

5. Remove the diskette and restart your computer.
The partitioning and formatting is complete.

6. Install the operating system.

®

© International Business Machines Corporation 2001

www.ibm.com/harddrive
IBM Technology Group Support Center

Telephone: [phone] or 507.286.5825
E-mail: [e-mail]

Singapore Technology Group Support Center

Telephone: [phone] or 65.6.418.9595
E-mail: [e-mail]

UK Technology Group Support Center

Telephone: [phone]
E-mail: [e-mail]

Germany Technology Group Support Center

Telephone: [phone]
E-mail: [e-mail]

IBM Systems Storage Division

5600 Cottle Road
San Jose CA 95193
www.ibm.com/storage

Printed in the United States of America
04-2001
All Rights Reserved

IBM is the registered trademark and Ultrastar is the trademark of International Business
Machines Corporation.

Other company, product, and service names may be trademarks or service marks of others.
Produced by the IBM Technology Group Support Center.
Hard Disk Drive Specifications for Ultrastar 36Z15 (Revision 1.0)
Product Description data represents IBM’s design objectives and is provided for comparative

purposes; actual results may vary based on a variety of factors. This product data does not
constitute a warranty. Questions regarding IBM’s warranty terms or methodology used to
derive this data should be referred to the IBM Technology Group Support Center. Data
subject to change without notice.

Date: 16 April 2001

IBM Technology Group Support Center version 1.0

Page 2