IBM 8306, 8309, 8314, 8313, 8301, 8315, 8305, 8308, 8302, 8304, 8303, 8312, 8311, 8310 User Manual

8.44 Mb
Loading...

IBM

 

Hardware Maintenance Manual Types 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310,

8311, 8312, 8313, 8314, and 8315

IBM

 

Hardware Maintenance Manual Types 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310,

8311, 8312, 8313, 8314, and 8315

Note: Before using this information and the product it supports, be sure to read the general information under “Notices” on page 305.

Second Edition (August 2004)

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS ISWITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimers or express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements or changes in the products or the programs described in this publication at any time.

Requests for technical information about IBM products should be made to your IBM Authorized Dealer or your IBM Marketing Representative.

© Copyright International Business Machines Corporation 2001. All rights reserved.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

Contents

Chapter 1. About this manual . . . .

.

1

Front bezel Types 8307, 8308, 8310, 8311, 8314, and

 

 

Important Safety Information . . . . . . . .

.

1

8315 . . . . . . . . . . . . . . . .

.

72

 

 

 

Replacing a microprocessor . . . . . . . .

.

72

Chapter 2. General Checkout. . . . .

.

3

Hard disk drive removal . . . . . . . . .

.

73

 

 

 

Types 8303, 8304, and 8312 . . . . . . .

.

73

Chapter 3. General information . . . .

.

5

Types 8305, 8306, 8309, and 8313 . . . . .

.

74

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 77

Features . . . . . . . . . . . . . . .

.

5

Power supply removal. . . . . . . . . .

.

77

Types 8301 and 8302 . . . . . . . . . .

.

5

Types 8301 and 8302 . . . . . . . . .

.

77

Types 8303, 8304, and 8312 . . . . . . .

.

7

Types 8303, 8304, and 8312 . . . . . . .

.

78

Types 8305, 8306, 8309, and 8313. . . . . .

.

9

Types 8305, 8306, 8309, and 8313 . . . . .

.

79

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 11

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 80

Physical specifications . . . . . . . . . .

.

13

System board removal . . . . . . . . . .

.

80

Types 8301 and 8302 . . . . . . . . .

.

13

Types 8301 and 8302 . . . . . . . . .

.

80

Types 8303, 8304 and 8312 . . . . . . .

.

14

Types 8303, 8304, and 8312 . . . . . . .

.

81

Types 8305, 8306, 8309, and 8313 . . . . .

.

16

Types 8305, 8306, 8309, and 8313 . . . . .

.

82

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 17

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 83

Available options . . . . . . . . . . .

.

18

Replacing the cover, Types 8301 and 8302 . . .

. 83

Types 8301 and 8302 . . . . . . . . .

.

18

 

 

 

Types 8303, 8304 and 8312 . . . . . . .

.

19

Chapter 7. Symptom-to-FRU Index . .

. 87

Types 8305, 8306, 8309, and 8313 . . . . .

.

20

Hard disk drive boot error . . . . . . . .

.

87

Types 8307, 8308, 8310, 8311, 8314, and 8315 .

. 21

Power Supply Errors . . . . . . . . . .

.

87

 

 

 

Chapter 4. Diagnostics . . . . . . . .

23

Diagnostic error codes . . . . . . . . . .

.

89

Beep symptoms . . . . . . . . . . .

.

107

Setup Utility program . . . . . . . . . .

.

24

No-beep symptoms . . . . . . . . . .

.

109

Product Recovery Program menu . . . . . .

. 25

POST error codes . . . . . . . . . . .

.

110

Diagnostics . . . . . . . . . . . . . .

26

Miscellaneous error messages . . . . . . .

.

125

Diagnostics program download. . . . . .

. 26

Undetermined problems. . . . . . . . .

.

127

Navigating through the diagnostics programs . . 26

 

 

 

Running diagnostics tests. . . . . . . .

.

26

Chapter 8. Parts listing . . . . . . .

129

Test selection . . . . . . . . . . . .

.

26

 

 

 

Test results . . . . . . . . . . . .

.

27

Chapter 9. Additional Service

 

 

Fixed disk advanced test (FDAT) . . . . .

. 27

 

 

Information . . . . . . . . . . . .

263

Quick and Full erase - hard drive . . . . .

.

29

Viewing the test log . . . . . . . . .

.

30

Security features . . . . . . . . . . .

.

263

 

 

 

Passwords . . . . . . . . . . . .

.

263

Chapter 5. Installing Options . . . . .

31

Vital product data . . . . . . . . . .

.

264

Installing external options . . . . . . . .

.

31

Management Information Format (MIF) . .

. 264

Alert on LAN . . . . . . . . . . .

.

265

Locating connectors on the front . . . . .

.

31

BIOS levels . . . . . . . . . . . . .

.

265

Locating the connectors on the rear . . . .

.

33

Flash update procedures. . . . . . . . .

.

265

Obtaining device drivers . . . . . . . .

.

39

Flash from Operating System (WinPhlash). . . 266

Installing internal options . . . . . . . .

.

39

Flash from CD-ROM ISO image . . . . .

. 266

Removing the cover . . . . . . . . .

.

40

Flash recovery boot block jumper. . . . . .

.

267

Locating components . . . . . . . . .

.

42

Power management . . . . . . . . . .

.

269

Identifying parts on the system board . . .

. 44

Automatic configuration and power interface

 

 

Installing memory . . . . . . . . . .

.

47

 

 

(ACPI) BIOS. . . . . . . . . . . .

.

269

Installing adapters . . . . . . . . . .

.

48

Advanced Power Management . . . . .

. 269

Installing internal drives . . . . . . . .

.

52

Automatic Hardware Power Management

 

 

Installing a rope clip . . . . . . . . .

.

64

 

 

features . . . . . . . . . . . . .

.

269

Changing the battery . . . . . . . . .

.

67

Setting Automatic Hardware Power

 

 

Replacing the cover and connecting the cables. . 67

 

 

Management features. . . . . . . . .

.

269

 

 

 

Chapter 6. FRU Removals . . . . . . 71

Automatic Power-On features . . . . . .

. 270

 

 

 

Removing the cover Types 8301 and 8302 . . .

. 71

 

 

 

Removing the CD-ROM drive Types 8301 and 8302

 

71

 

 

 

© Copyright IBM Corp. 2001

iii

Chapter 10. Related service

 

 

 

Grounding requirements . . . . . .

.

.

275

information . . . . . . . . . . .

.

271

Safety notices (multi-lingual translations) .

.

.

275

Safety information. . . . . . . . . .

.

.

271

Send us your comments! . . . . . . .

.

.

304

Problem determination tips. . . . . . .

.

.

305

General safety . . . . . . . . . .

.

.

271

Notices . . . . . . . . . . . . .

.

.

305

Electrical safety. . . . . . . . . .

.

.

272

Trademarks . . . . . . . . . . . .

.

.

306

Safety inspection guide . . . . . . .

.

.

273

 

 

 

 

Handling electrostatic discharge-sensitive

 

 

 

 

 

 

 

devices . . . . . . . . . . . .

.

.

274

 

 

 

 

iv Hardware Maintenance Manual

Chapter 1. About this manual

This manual contains service and reference information for IBM® computer Types 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, and 8315.

This manual is divided into product service sections and a related service section, as follows:

vThe product service sections include procedures for isolating problems to a FRU, a Symptom-to-FRU Index, additional service information and an illustrated parts catalog.

vThe related service section includes safety notices and safety information, and problem determination tips.

Note:

This manual is intended for trained servicers who are familiar with IBM Personal Computer products. Use this manual along with advanced diagnostic tests to troubleshoot problems effectively.

Before servicing an IBM product, be sure to review the “Safety information” on page 271.

Important Safety Information

Be sure to read all caution and danger statements in this book before performing any of the instructions.

Prenez connaissance de toutes les consignes de type Attention et Danger avant de procéder aux opérations décrites par les instructions.

Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.

Accertarsi di leggere tutti gli avvisi di attenzione e di pericolo prima di effettuare qualsiasi operazione.

© Copyright IBM Corp. 2001

1

Leia todas as instruções de cuidado e perigo antes de executar qualquer operação.

Lea atentamente todas las declaraciones de precaución y peligro ante de llevar a cabo cualquier operación.

2 Hardware Maintenance Manual

Chapter 2. General Checkout

This general checkout procedure is for Types 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, and 8315 computers.

Attention:

The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving or formatting. Data or programs can be overwritten if you select an incorrect drive.

Diagnostic error messages appear when a test program finds a problem with a hardware option. For the test programs to properly determine if a test Passed, Failed or Aborted, the test programs check the error-return code at test completion. See “Diagnostics” on page 26.

General error messages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

Notes:

vTypes 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8313, 8314, and 8315 computers default to come up quiet (no beep and no memory count and checkpoint code display) when no errors are detected by POST.

vTo enable beep and memory count and checkpoint code display when a successful POST occurs, do the following:

1.Select Start Options in the Configuration/Setup Utility program (see “Setup Utility program” on page 24).

2.Set Power-On Self-Test to Enhanced.

vBefore replacing any FRUs, ensure that the latest level of BIOS is installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the system board. For more information on how to determine and obtain the latest level BIOS, see “BIOS levels” on page 265.

vIf multiple error codes are displayed, diagnose the first error code displayed.

vIf the computer hangs with a POST error, go to Symptom-to-FRU Indexon page 87.

vIf the computer hangs and no error is displayed, go to “Undetermined problems” on page 127.

vIf an installed device is not recognized by the diagnostics program, that device might be defective.

001

1.Power-off the computer and all external devices.

2.Check all cables and power cords.

3.Make sure the system board is seated properly.

4.Set all display controls to the middle position.

5.Power-on all external devices.

6.Power-on the computer.

7.Check for the following response:

v Readable instructions or the Main Menu.

© Copyright IBM Corp. 2001

3

DID YOU RECEIVE THE CORRECT RESPONSE?

If NO, continue to 002 .

If YES, proceed to 003 .

002

If the Power Management feature is enabled, do the following:

1.Start the Configuration/Setup Utility program (see “Setup Utility program” on page 24)

2.Select Power Management from the Configuration/Setup Utility program menu.

3.Select APM.

4.Be sure APM BIOS Mode is set to Disabled. If it is not, press Left Arrow (}) or Right Arrow (Æ) to change the setting.

5.Select Automatic Hardware Power Management.

6.Set Automatic Hardware Power Management to Disabled.

7.If the problem persists, continue to 003 .

003

Run the Diagnostic programs. If necessary, refer to “Diagnostics” on page 26.

vIf you receive an error, replace the part that the diagnostic program calls out or go to Symptom-to-FRU Indexon page 87.

vIf the test stops and you cannot continue, replace the last device tested.

4 Hardware Maintenance Manual

Chapter 3. General information

This IBM® computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change.

Adding hardware options to your computer is an easy way to increase its capabilities. Instructions for installing external and internal options are included in this publication. When adding an option, use these instructions along with the instructions that come with the option.

Go to Access IBM for general information about the use, operation, and maintenance of your computer. Access IBM also contains information to help solve problems and get repair service or other technical assistance.

Features

This section details the features available in each computer machine Type.

Types 8301 and 8302

This section provides an overview of the computer features and preinstalled software.

Microprocessor

Intel® Pentium® 4 processor with 512 KB of internal L2 cache memory and Intel NetBurstmicro-architecture

Memory

vSupport for two dual inline memory modules (DIMMs)

v512 KB flash memory for system programs

Internal drives

vInternal hard disk drive

Note: The hard disk drive should only be removed for maintenance or upgrade and not for daily security.

vEIDE CD-ROM drive (some models)

Video subsystem

Intel Extremegraphics

Audio subsystem

Integrated SoundMAX 3 audio

Connectivity

10/100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN® feature

© Copyright IBM Corp. 2001

5

System management features

vRemote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)

vWake on LAN

vWake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem)

vRemote Administration

vAutomatic power-on startup

vSystem Management (SM) BIOS and SM software

vAbility to store POST hardware test results

Input/output features

v25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)

vTwo 9-pin serial connectors

vSix 4-pin, USB connectors

vPS/2® mouse connector

vPS/2 keyboard connector

vEthernet connector

vVGA monitor connector

vThree audio connectors (line in, line out, and microphone)

Expansion

Two drive bays

Power

v125 W power supply with manual voltage selection switch

vAutomatic 50/60 Hz input frequency switching

vAdvanced Power Management support

vAdvanced Configuration and Power Interface (ACPI) support

Security features

vUser and administrator passwords

vSupport for the addition of a rope clip and lockable cable

vSupport for the addition of an integrated cable lock

vStartup sequence control

vStartup without keyboard or mouse

vUnattended start mode

vSerial and parallel port I/O control

vSecurity profile by device

IBM preinstalled software

Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

Operating systems (preinstalled) (varies by model type)

Note: Not all countries or regions will have these operating systems. v Microsoft® Windows® XP Home

6 Hardware Maintenance Manual

vMicrosoft Windows XP Professional

vMicrosoft Windows 2000 Professional

Operating systems (tested for compatibility)1

vMicrosoft Windows NT® Workstation Version 4.0

vMicrosoft Windows 98 Second Edition

vMicrosoft Windows Millennium®

vOS/2®

Types 8303, 8304, and 8312

This section provides an overview of the computer features and preinstalled software.

Microprocessor (varies by model type)

Intel® Pentium® 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurstmicro-architecture

Memory

vSupport for two dual inline memory modules (DIMMs)

v512 KB flash memory for system programs

Internal drives

v3.5-inch, 1.44 MB diskette drive

vInternal hard disk drive

vEIDE CD-ROM drive or DVD-ROM drive (some models)

Video subsystem

vIntel Extremegraphics

vAccelerated graphics port (AGP) video adapter slot on the system board (some models)

Audio subsystem

Integrated SoundMAX 3 audio

1.The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.

Chapter 3. General information 7

Connectivity

v10/100/1000 Mbps integrated Intel Ethernet controller that supports the Wake on LAN® feature

vSoft modem V.90/V.44 (some models)

System management features

vRemote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)

vWake on LAN

vWake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem)

vRemote Administration

vAutomatic power-on startup

vSystem Management (SM) BIOS and SM software

vAbility to store POST hardware test results

Input/output features

v25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)

vTwo 9-pin serial connectors

vSix 4-pin, USB connectors

vPS/2® mouse connector

vPS/2 keyboard connector

vEthernet connector

vVGA monitor connector

vThree audio connectors (line in, line out, and microphone)

vFront connectors for headphone, microphone, IEEE 1394, and S/PDIF (some models)

Expansion

vThree drive bays

vThree 32-bit peripheral component interconnect (PCI) adapter slots (supports low-profile adapters only)

vOne accelerated graphics port (AGP) expansion slot (supports low-profile adapters only)

Power

v160 W power supply with manual voltage selection switch

vAutomatic 50/60 Hz input frequency switching

vAdvanced Power Management support

vAdvanced Configuration and Power Interface (ACPI) support

Security features

vUser and administrator passwords

vSupport for the addition of a rope clip and lockable cable

vSupport for the addition of an integrated cable lock

vStartup sequence control

vStartup without diskette drive, keyboard, or mouse

vUnattended start mode

8 Hardware Maintenance Manual

vDiskette and hard disk I/O control

vSerial and parallel port I/O control

vSecurity profile by device

IBM preinstalled software

Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

Operating systems (preinstalled) (varies by model type)

Note: Not all countries or regions will have these operating systems.

vMicrosoft® Windows® XP Home

vMicrosoft Windows XP Professional

vMicrosoft Windows 2000 Professional

Operating systems (tested for compatibility)2

vMicrosoft Windows NT® Workstation Version 4.0

vMicrosoft Windows 98 Second Edition

vMicrosoft Windows Millennium®

vOS/2®

Types 8305, 8306, 8309, and 8313

This section provides an overview of the computer features and preinstalled software.

Microprocessor (varies by model type)

Intel® Pentium® 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurstmicro-architecture

Memory

vSupport for two dual inline memory modules (DIMMs)

v512 KB flash memory for system programs

Internal drives

v3.5-inch, 1.44 MB diskette drive

vInternal hard disk drive

vEIDE CD drive or DVD drive (some models)

Video subsystem

vIntel Extremegraphics

vAccelerated graphics port (AGP) video adapter slot on the system board (some models)

Audio subsystem

Integrated SoundMAX 3 audio

2.The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.

Chapter 3. General information 9

Connectivity

10/100/1000 Mbps integrated Intel Ethernet controller that supports the Wake on LAN® feature

System management features

vRemote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)

vWake on LAN

vWake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem)

vRemote Administration

vAutomatic power-on startup

vSystem Management (SM) BIOS and SM software

vAbility to store POST hardware test results

Input/output features

v25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)

vTwo 9-pin serial connectors

vSix 4-pin, USB connectors

vPS/2® mouse connector

vPS/2 keyboard connector

vEthernet connector

vVGA monitor connector

vThree audio connectors (line in, line out, and microphone)

Expansion

vFour drive bays

vThree 32-bit peripheral component interconnect (PCI) adapter slots

vOne accelerated graphics port (AGP) expansion slot

Power

v185 W power supply with manual voltage selection switch

vAutomatic 50/60 Hz input frequency switching

vAdvanced Power Management support

vAdvanced Configuration and Power Interface (ACPI) support

Security features

vUser and administrator passwords

vSupport for the addition of a rope clip and lockable cable

vSupport for the addition of an integrated cable lock

vStartup sequence control

vStartup without diskette drive, keyboard, or mouse

vUnattended start mode

vDiskette and hard disk I/O control

vSerial and parallel port I/O control

vSecurity profile by device

10 Hardware Maintenance Manual

IBM preinstalled software

Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

Operating systems (preinstalled) (varies by model type)

Note: Not all countries or regions will have these operating systems.

vMicrosoft® Windows® XP Home

vMicrosoft Windows XP Professional

vMicrosoft Windows 2000 Professional

Operating systems (tested for compatibility)3

vMicrosoft Windows NT® Workstation Version 4.0

vMicrosoft Windows 98 Second Edition

vMicrosoft Windows Millennium®

vOS/2®

Types 8307, 8308, 8310, 8311, 8314, and 8315

This section provides an overview of the computer features and preinstalled software.

Microprocessor (varies by model type)

Intel® Pentium® 4 processor with 256 KB or 512 KB of internal L2 cache memory and Intel NetBurstmicro-architecture

Memory

vSupport for two dual inline memory modules (DIMMs)

v512 KB flash memory for system programs

Internal drives

v3.5-inch, 1.44 MB diskette drive

vInternal hard disk drive

vEIDE CD drive or DVD drive

Video subsystem

vIntel Extremegraphics

vAccelerated graphics port (AGP) video adapter slot on the system board (some models)

Audio subsystem

Integrated SoundMAX 3 audio

Connectivity

v10/100 Mbps integrated Intel Ethernet controller that supports the Wake on LAN® feature

3.The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.

Chapter 3. General information 11

v Soft modem V.90/V.44 (some models)

System management features

vRemote Program Load (RPL) and Dynamic Host Configuration Protocol (DHCP)

vWake on LAN

vWake on Ring (in the IBM Setup Utility program, this feature is called Serial Port Ring Detect for an external modem and Modem Ring Detect for an internal modem)

vRemote Administration

vAutomatic power-on startup

vSystem Management (SM) BIOS and SM software

vAbility to store POST hardware test results

Input/output features

v25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP)

vTwo 9-pin serial connectors

vSix 4-pin, USB connectors

vPS/2® mouse connector

vPS/2 keyboard connector

vEthernet connector

vVGA monitor connector

vThree audio connectors (line in, line out, and microphone)

vIEEE 1394 connector (some models)

vFront connectors for microphone and headphone (some models)

Expansion

vFive drive bays

vThree 32-bit peripheral component interconnect (PCI) adapter slots

vOne accelerated graphics port (AGP) expansion slot

Power

v185 W power supply with manual voltage selection switch

vAutomatic 50/60 Hz input frequency switching

vAdvanced Power Management support

vAdvanced Configuration and Power Interface (ACPI) support

Security features

vUser and administrator passwords

vSupport for the addition of a rope clip and lockable cable

vSupport for the addition of an integrated cable lock

vStartup sequence control

vStartup without diskette drive, keyboard, or mouse

vUnattended start mode

vDiskette and hard disk I/O control

vSerial and parallel port I/O control

vSecurity profile by device

12 Hardware Maintenance Manual

IBM preinstalled software

Your computer might come with preinstalled software. If it does, an operating system, device drivers to support built-in features, and other support programs are included.

Operating systems (preinstalled) (varies by model type)

Note: Not all countries or regions will have these operating systems.

vMicrosoft® Windows® XP Home

vMicrosoft Windows XP Professional

vMicrosoft Windows 2000 Professional

Operating systems (tested for compatibility)4

vMicrosoft Windows NT® Workstation Version 4.0

vMicrosoft Windows 98 Second Edition

vMicrosoft Windows Millennium®

vOS/2®

Physical specifications

This section details the physical specifications for each computer Type.

Types 8301 and 8302

This section lists the physical specifications for Type 8301 and 8302 computers.

4.The operating systems listed here are being tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by IBM as compatible with your computer following the publication of this booklet. Corrections and additions to this list are subject to change. To determine if an operating system has been tested for compatibility, check the Web site of the operating system vendor.

Chapter 3. General information 13

Dimensions

Height: 110 mm (4.3 in.)

Width: 310 mm (12.2 in.)

Depth: 343 mm (13.5 in.)

Weight

Minimum configuration as shipped: 8.1 kg (18 lb)

Maximum configuration: 9.1 kg (20 lb)

Environment

Air temperature:

System on: 10° to 35°C (50° to 95° F)

System off: 10° to 43°C (50° to 110° F)

Maximum altitude: 2134 m (7000 ft)

Note: The maximum altitude, 2134 m (7000 ft), is the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified.

Humidity:

System on: 8% to 80%

System off: 8% to 80%

Electrical input

Input voltage:

Low range:

Minimum: 90 V ac

Maximum: 137 V ac

Input frequency range: 57–63 Hz

Voltage switch setting: 115 V ac

High range:

Minimum: 180 V ac

Maximum: 265 V ac

Input frequency range: 47–53 Hz

Voltage switch setting: 230 V ac

Input kilovolt-amperes (kVA) (approximate):

Minimum configuration as shipped: 0.08 kVA

Maximum configuration: 0.30 kVA

Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use.

Heat output (approximate) in British thermal units (Btu) per hour:

Minimum configuration: 257 Btu/hr (75 watts)

Maximum configuration: 497 Btu/hr (145 watts)

Airflow

Approximately 0.40 cubic meters per minute (14 cubic feet per minute) maximum

Acoustical noise-emission values

Average sound-pressure levels:

At operator position:

Idle: 34 dBA

Operating: 36 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 31 dBA

Operating: 34 dBA

Declared (upper limit) sound-power levels:

Idle: 4.4 bels

Operating: 4.7 bels

Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate.

Note: See the Quick Reference for the classification of your computer.

Types 8303, 8304 and 8312

This section lists the physical specifications for Type 8303, 8304, and 8312 computers.

14 Hardware Maintenance Manual

Dimensions

Height: 104 mm (4.1 in.)

Width: 360 mm (14.2 in.)

Depth: 412 mm (16.2 in.)

Weight

Minimum configuration as shipped: 8.1 kg (18 lb)

Maximum configuration: 9.1 kg (20 lb)

Environment

Air temperature:

System on: 10° to 35°C (50° to 95° F)

System off: 10° to 43°C (50° to 110° F)

Maximum altitude: 2134 m (7000 ft)

Note: The maximum altitude, 2134 m (7000 ft), is the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified.

Humidity:

System on: 8% to 80%

System off: 8% to 80%

Electrical input

Input voltage:

Low range:

Minimum: 90 V ac

Maximum: 137 V ac

Input frequency range: 57–63 Hz

Voltage switch setting: 115 V ac

High range:

Minimum: 180 V ac

Maximum: 265 V ac

Input frequency range: 47–53 Hz

Voltage switch setting: 230 V ac

Input kilovolt-amperes (kVA) (approximate):

Minimum configuration as shipped: 0.08 kVA

Maximum configuration: 0.30 kVA

Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use.

Heat output (approximate) in British thermal units (Btu) per hour:

Minimum configuration: 257 Btu/hr (75 watts)

Maximum configuration: 806 Btu/hr (235 watts)

Airflow

Approximately 0.45 cubic meters per minute (16 cubic feet per minute) maximum

Acoustical noise-emission values

Average sound-pressure levels:

At operator position:

Idle: 32 dBA

Operating: 35 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 29 dBA

Operating: 33 dBA

Declared (upper limit) sound-power levels:

Idle: 4.4 bels

Operating: 4.7 bels

Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate.

Note: See the Quick Reference for the classification of your computer.

Chapter 3. General information 15

Types 8305, 8306, 8309, and 8313

This section lists the physical specifications for your computer.

Dimensions

Height: 140 mm (5.5 in.)

Width: 425 mm (16.7 in.)

Depth: 414 mm (16.3 in)

Weight

Minimum configuration as shipped: 10.0 kg (22 lb)

Maximum configuration: 11.4 kg (25.0 lb)

Environment

Air temperature:

System on: 10° to 35°C (50° to 95° F)

System off: 10° to 43°C (50° to 110° F)

Maximum altitude: 2134 m (7000 ft)

Note: The maximum altitude, 2134 m (7000 ft), is the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified.

Humidity:

System on: 8% to 80%

System off: 8% to 80%

Electrical input

Input voltage:

Low range:

Minimum: 90 V ac

Maximum: 137 V ac

Input frequency range: 57–63 Hz

Voltage switch setting: 115 V ac

High range:

Minimum: 180 V ac

Maximum: 265 V ac

Input frequency range: 47–53 Hz

Voltage switch setting: 230 V ac

Input kilovolt-amperes (kVA) (approximate):

Minimum configuration as shipped: 0.08 kVA

Maximum configuration: 0.3 kVA

Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use.

Heat output (approximate) in British thermal units (Btu) per hour:

Minimum configuration: 257 Btu/hr (75 watts)

Maximum configuration: 890 Btu/hr (260 watts)

Airflow

Approximately 0.56 cubic meters per minute (20 cubic feet per minute) maximum

Acoustical noise-emission values

Average sound-pressure levels:

At operator position:

Idle: 33 dBA

Operating: 36 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 30 dBA

Operating: 33 dBA

Declared (upper limit) sound-power levels:

Idle: 4.4 bels

Operating: 4.7 bels

Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate.

Note: See the Quick Reference for the classification of your computer.

16 Hardware Maintenance Manual

Types 8307, 8308, 8310, 8311, 8314, and 8315

This section lists the physical specifications for your computer.

Dimensions

Height: 413 mm (16.25 in.)

Width: 191 mm (7.5 in.)

Depth: 406 mm (16 in.)

Weight

Minimum configuration as shipped: 9.1 kg (20 lb)

Maximum configuration: 10.2 kg (22.5 lb)

Environment

Air temperature:

System on: 10° to 35°C (50° to 95° F)

System off: 10° to 43°C (50° to 110° F)

Maximum altitude: 2134 m (7000 ft)

Note: The maximum altitude, 2134 m (7000 ft), is the maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified.

Humidity:

System on: 8% to 80%

System off: 8% to 80%

Electrical input

Input voltage:

Low range:

Minimum: 90 V ac

Maximum: 137 V ac

Input frequency range: 57–63 Hz

Voltage switch setting: 115 V ac

High range:

Minimum: 180 V ac

Maximum: 265 V ac

Input frequency range: 47–53 Hz

Voltage switch setting: 230 V ac

Input kilovolt-amperes (kVA) (approximate):

Minimum configuration as shipped: 0.08 kVA

Maximum configuration: 0.3 kVA

Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use.

Heat output (approximate) in British thermal units (Btu) per hour:

Minimum configuration: 257 Btu/hr (75 watts)

Maximum configuration: 890 Btu/hr (260 watts)

Airflow

Approximately 0.76 cubic meters per minute (26 cubic feet per minute) maximum

Acoustical noise-emission values

Average sound-pressure levels:

At operator position:

Idle: 30 dBA

Operating: 34 dBA

At bystander position - 1 meter (3.3 ft):

Idle: 29 dBA

Operating: 33 dBA

Declared (upper limit) sound-power levels:

Idle: 4.4 bels

Operating: 4.7 bels

Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate.

Note: See the Quick Reference for the classification of your computer.

Chapter 3. General information 17

Available options

This section details the options available in each computer Type.

Types 8301 and 8302

The following are some available options:

vExternal options

Parallel port devices, such as printers and external drives

Serial port devices, such as external modems and digital cameras

Audio devices, such as external speakers for the sound system

USB devices, such as printers, joysticks, and scanners

Monitors

vInternal drives, such as

CD-ROM drive (some models)

Hard disk drive

For the latest information about available options, see the following World Wide Web pages:

vhttp://www.ibm.com/pc/us/options/

vhttp://www.ibm.com/pc/support/

You can also obtain information by calling the following telephone numbers:

vWithin the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative.

vWithin Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.

vOutside the United States and Canada, contact your IBM reseller or IBM marketing representative.

18 Hardware Maintenance Manual

Types 8303, 8304 and 8312

The following are some available options:

vExternal options

Parallel port devices, such as printers and external drives

Serial port devices, such as external modems and digital cameras

Audio devices, such as external speakers for the sound system

USB devices, such as printers, joysticks, and scanners

Security device, such as a rope clip

Monitors

IEEE 1394 devices (requires an IEEE 1394 adapter)

vInternal options

System memory, called dual inline memory modules (DIMMs)

Peripheral component interconnect (PCI) adapters (supports low-profile adapters only)

Accelerated graphics port (AGP) adapters (supports low-profile adapters only)

Internal drives, such as:

-CD-ROM drive and DVD-ROM drive (some models)

-Hard disk drive

-Diskette drives and other removable media drives

For the latest information about available options, see the following World Wide Web pages:

vhttp://www.ibm.com/pc/us/options/

vhttp://www.ibm.com/pc/support/

You can also obtain information by calling the following telephone numbers:

vWithin the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative.

vWithin Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.

vOutside the United States and Canada, contact your IBM reseller or IBM marketing representative.

Chapter 3. General information 19

Types 8305, 8306, 8309, and 8313

The following are some available options:

vExternal options

Parallel port devices, such as printers and external drives

Serial port devices, such as external modems and digital cameras

Audio devices, such as external speakers for the sound system

USB devices, such as printers, joysticks, and scanners

Security device, such as a rope clip

Monitors

vInternal options

System memory, called dual inline memory modules (DIMMs)

Peripheral component interconnect (PCI) adapters

Accelerated graphics port (AGP) adapters

Internal drives, such as:

-CD drive or DVD drive (some models)

-Hard disk drive

-Diskette drives and other removable media drives

For the latest information about available options, see the following World Wide Web pages:

vhttp://www.ibm.com/pc/us/options/

vhttp://www.ibm.com/pc/support/

You can also obtain information by calling the following telephone numbers:

vWithin the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative.

vWithin Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.

vOutside the United States and Canada, contact your IBM reseller or IBM marketing representative.

20 Hardware Maintenance Manual

Types 8307, 8308, 8310, 8311, 8314, and 8315

The following are some available options:

vExternal options

Parallel port devices, such as printers and external drives

Serial port devices, such as external modems and digital cameras

Audio devices, such as external speakers for the sound system

USB devices, such as printers, joysticks, and scanners

Security device, such as a rope clip

Monitors

IEEE 1394 devices (requires an IEEE 1394 adapter)

vInternal options

System memory, called dual inline memory modules (DIMMs)

Peripheral component interconnect (PCI) adapters

Accelerated graphics port (AGP) adapters

Internal drives, such as:

-CD drive and DVD drive

-Hard disk drive

-Diskette drives and other removable media drives

For the latest information about available options, see the following World Wide Web pages:

vhttp://www.ibm.com/pc/us/options/

vhttp://www.ibm.com/pc/support/

You can also obtain information by calling the following telephone numbers:

vWithin the United States, call 1-800-IBM-2YOU (1-800-426-2968), your IBM reseller, or IBM marketing representative.

vWithin Canada, call 1-800-565-3344 or 1-800-IBM-4YOU.

vOutside the United States and Canada, contact your IBM reseller or IBM marketing representative.

Chapter 3. General information 21

22 Hardware Maintenance Manual

Chapter 4. Diagnostics

The following tools are available to help identify and resolve hardware-related problems.

vSetup Utility program

vPower-On Self-Test (POST)

POST Beep Codes

Error Code Format

vDiagnostics program

vRecovery utility

Factory Contents

Partial recovery

vRepair utility

© Copyright IBM Corp. 2001

23

Setup Utility program

Attention:

A customized setup configuration (other than default settings) might exist on the computer you are servicing. Running the Setup Utility program might alter those settings. Note the current configuration settings and verify that the settings are in place when service is complete.

The Setup Utility (configuration) program is stored in the permanent memory of the computer. This program includes settings for the following:

vSystem Summary

vProduct Data

vDevices and I/O Ports

vStart Options

vDate and Time

vSystem Security

vAdvanced Setup

vPower Management

To run the Setup Utility program, use the following procedure.

1.Power-off the computer and wait for a few seconds until all in-use lights go off.

2.Power-on the computer.

3.When the Setup Utility prompt appears on the screen during start-up, press F1. The Setup Utility menu will appear.

4.Follow the instructions on the screen.

5.When finished, select System Summary to verify that any configuration changes have been accepted.

24 Hardware Maintenance Manual

Product Recovery Program menu

Type 8301, 8302, 8303, 8304, 8305, 8306, 8307, 8308, 8309, 8310, 8311, 8312, 8314, and 8315 machines have recovery and diagnostics programs on a separate hard drive partition. The Enhanced Diagnostics diskette is not shipped with the machine. To download the Diagnostics program, see “Diagnostics program download” on page 26.

At startup, the machine displays the following prompt:

To start the Product Recovery Program, press F11

Attention: Make sure all data is backed up to avoid loss when the Product

Recovery program is used.

After depressing F11, you are given the following options.

vFactory Contents

This utility reformats the hard drive and restores all original files.

vSystem utilities

1.Repair (Windows NT 4.0 and 2000 Only)

This runs the Windows NT 4.0 emergency repair utility.

2.Run Diagnostics

Runs the IBM Enhanced Diagnostic Program.

3.Create a Diagnostics Diskette

Creates a bootable diagnostic diskette.

4.System Information

Displays information about your computer configuration and allows the user to gather system information that would be needed during a Help Center call.

5.Create Recovery/Repair Diskette (Disk to Disk Solution Only)

Creates a startable diskette to restore access to the IBM Product Recovery program on the hard disk.

6.Recovery CD

In the event of a Hard Disk Drive failure, a Recovery CD can be used to restore the Hard Disk Drive to the original factory preset. Be sure to use the Recovery CD FRU list to obtain the proper recovery CD for the computer model you are servicing.

Chapter 4. Diagnostics 25

Diagnostics

The Diagnostics program uses a full range of diagnostic utilities to determine the operating condition of the computer’s hardware components.

For a complete list of error codes and messages, see Symptom-to-FRU Indexon page 87.

Note: The fans in this system may turn off under normal operation. This is a noise-level reduction feature, and should not be taken to mean there is something wrong with the system.

Diagnostics program download

To download the Diagnostics program, do the following:

vGo to http://www.ibm.com/.

vSelect Support.

vSelect Personal computing from the Get product support forpull-down menu.

vSearch for the machine type in the Quick Pathbox on the left.

vSelect Downloadable files from the options on the left.

vSelect Diagnostics from the pull down menu.

Navigating through the diagnostics programs

Use the cursor movement keys to navigate within the menus.

vThe Enter key is used to select a menu item.

vThe Esc key is used to back up to the previous menu.

vFor online help select F1.

Running diagnostics tests

There are four ways to run the diagnostic tests.

1.Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics menu and then press Enter.

This will automatically run a pre-defined group of tests from each test category. Run Normal Test runs a more extensive set of tests than does Run Quick Test and takes longer to execute.

2.Press F5 to automatically run all selected tests in all categories. See Test Selection.

3.From within a test category, press Ctrl-Enter to automatically run only the selected tests in that category. See Test Selection.

4.Using the cursor movement keys, highlight a single test within a test category, then press Enter. This will run only that test.

Press Esc at any time to stop the testing process.

Test results, (N/A, PASSED, FAILED, ABORTED), are displayed in the field beside the test description and in the test log. See “Viewing the test log” on page 30.

Test selection

To select one or more tests, use the following procedure.

1.Open the corresponding test category.

2.Using the cursor movement keys, highlight the desired test.

26 Hardware Maintenance Manual

3.Press the space bar.

A selected test is marked by >>. Pressing the space bar again de-selects a test and removes the chevron.

4.Repeat steps 2 and 3 above to select all desired tests.

Test results

Diagnostics test results will produce the following error code format:

Function

Failure Type DeviceID

Date

ChkDigits

Text

Code

 

 

 

 

 

 

 

 

 

vFunction Code:

Represents the feature or function within the PC.

vFailure Type:

Represents the type of error encountered.

vDeviceID:

Contains the component’s unit-ID which corresponds to either a fixed disk drive, removable media drive, serial or parallel port, processor, specific RIMM, or a device on the PCI bus.

vDate:

Contains the date on which the diagnostic test was run. The date is retrieved from CMOS and displayed using the YYYYMMDD format.

vChkDigits:

Contains a 2-digit check-digit value to ensure the following:

Diagnostics were run on the specified date.

Diagnostics were run on the specified IBM computer.

The diagnostic error code is recorded correctly.

vText:

Description of the error.

Note: See “Diagnostic error codes” on page 89 for error code listings.

Fixed disk advanced test (FDAT)

PC-Doctor’s (PCDR) Fixed-Disk Advanced Test module (FDAT) is a full-featured highly configurable fixed-disk test suite. The configurable capabilities of FDAT allow users to enable or disable specific tests, enable or disable testing features, control the test log detail, alter testing parameters, etc. FDAT will test for and report most commonly found errors on a fixed-disk drive and is able to test up to 128 SCSI and 4 IDE drives (up to 132 total drives). Drive information is gathered through FDAT’s enumeration of available devices and user specific configuration parameters located in the FDAT.INI. FDAT uses information supplied by these features to indicate specifically what devices are available for test, what tests are available for the device, device properties, etc. Modify the FDAT.INI file in PC Doctor for DOS to change testing parameters

FDAT consists of the following subtests and features.

Fixed-Disk Tests:

vSeek Tests: - checks the physical operation of the drive head.

– Linear Seek

Chapter 4. Diagnostics 27

Random Seek

Min-Max Seek

Butterfly Seek

v Verify Tests: - checks the integrity of the data present on the media.

Linear Verify

Random Verify

vSurface Scan Tests: - checks the drive media for defects.

Surface Scan (Linear)

Surface Scan (Aggressive) - this is disabled for normal customer use.

Surface Scan (Random)

vSMART: - checks the SMART functionality for drives that support SMART.

Start SMART Self-Test

Get SMART test results

Other Test Features:

vWrite-Splice Repair - detects and corrects Error Correction Code errors during Verify tests.

vAuto Spin Down - a gradual spin down of the drive platters to avoid damaging the media.

vManufacturer Log - an in-depth manufacturer supported log of errors on the drive.

Multitasking:

To allow simultaneous testing of multiple hard drives whenever possible, the FDAT module is written as a set of multitasking functions. Each drive under test can run the same test or run a different test at the same time. Each subtest is written to handle a single test pass and all test variables are kept track of in a structure unique for each drive . However, when testing IDE drives, FDAT will not perform simultaneous testing of IDE drives that are attached to the same IDE cable. For example, if FDAT is testing four IDE drives on a PC, it will perform simultaneous testing on drives 1 and 3 first (master drives), then perform tests on 2 and 4 (slave drives). FDAT will also perform simultaneous testing on a master and slave that are on separate IDE cables, but will not perform simultaneous tests on a master and slave on the same IDE cable. This generally increases the amount of time needed to test multiple IDE drives. Another limitation of FDAT’S multitasking capability is the use of Ultra DMA (UDMA). Only one drive at a time can access the UDMA channel and the UDMA channel buffer must be kept high in order to maintain a speed advantage over other data transfer modes. In order to use the UDMA channel during testing, users must disable the multitasking feature.

Destructive vs non-destructive testing:

Most of the tests found in FDAT are non-destructive. This means that PCDR will preserve any data that is present on the tested media prior to beginning any destructive operations (i.e. write operations). However, users can run certain tests in destructive mode (i.e. surface scan tests). Destructive tests will speed up testing because FDAT does not preserve the data on the media prior to the test beginning. Unlike non-destructive tests, any data present on the media prior to the test beginning is lost. FDAT allows for enabling or disabling destructive tests, as well as specifying a range of destructive and non-destructive sectors on the tested drive. This is done through the configuration of the FDAT.INI .If destructive and

28 Hardware Maintenance Manual

non-destructive ranges somehow overlap, then the overlapped area is considered non-destructive. For example, if users specify both destructive and non-destructive ranges as the same, then the entire drive is tested as non-destructive.

Quick and Full erase - hard drive

The Diagnostics program offers two hard drive format utilities:

vQuick Erase Hard Drive

vFull Erase Hard Drive

The Quick Erase Hard Drive provides a DOS utility that performs the following steps.

vDestroys the Master Boot Record (MBR) on the hard drive.

vDestroys all copies of the FAT Table on all partitions (both the master and backup).

vDestroys the partition table.

vProvides messages that warn the user that this is a non-recoverable process.

Chapter 4. Diagnostics 29

The Full Erase Hard Drive provides a DOS utility that performs the following steps.

vPerforms all the steps in Quick Erase.

vProvides a DOS utility that writes random data to all sectors of the hard drive.

vProvide an estimate of time to completion along with a visual representation of completion status.

vProvides messages that warn the user about non-recoverable process.

Important: Make sure that all data is backed up before using the Quick or Full Erase functions.

To select the Quick Erase or Full Erase Hard Drive utility, use the following procedure.

1.Select the UTILITY option on the toolbar and press Enter.

2.Select either the QUICK ERASE or FULL ERASE HARD DISK option and follow the instructions.

Viewing the test log

Errors reported by the diagnostic test will be displayed by the program as a failed test.

To view details of a failure or to view a list of test results, use the following procedure from any test category screen.

vPress F3 to activate the log file.

vPress F3 again to save the file to diskette or F2 to print the file.

30 Hardware Maintenance Manual

Chapter 5. Installing Options

Installing external options

This chapter shows the various external connectors on the computer to which can be attached external options, such as external speakers, a printer, or a scanner. For some external options, additional software must be installed in addition to making the physical connection. When adding an external option, use the information in this chapter to identify the required connector, and then use the instructions that come with the option to help make the connection and install any software or device drivers that are required for the option.

Important: Before you install or remove any option, read “Safety information” on page 271. These precautions and guidelines will help you work safely.

Locating connectors on the front

Types 8301 and 8302

The following illustration shows the locations of the connectors on the front of the computer.

1USB connector 2USB connector

Types 8303, 8304, and 8312

The following illustration shows the locations of the connectors on the front of the computer.

 

 

 

 

 

 

 

 

31

© Copyright IBM Corp. 2001

1USB connector 2USB connector

Types 8305, 8306, 8309, and 8313

The following illustration shows the locations of the connectors on the front of the computer.

1USB connector 2USB connector

Types 8307, 8308, 8310, 8311, 8314, and 8315

The following illustration shows the locations of the connectors on the front of the computer.

Note: Not all computer models will have the following connectors.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1IEEE 1394 connector

4USB connector

 

2Microphone connector

5USB connector

 

3Headphone connector

 

 

32 Hardware Maintenance Manual

Locating the connectors on the rear

Types 8301 and 8302

The following illustration shows the locations of the connectors on the rear of the computer.

1Serial connector 2Mouse connector 3Parallel connector 4Ethernet connector 5Audio line in connector 6Power connector 7Audio line out connector

8 Microphone connector 9 USB connectors 10VGA monitor connector 11Serial connector 12USB connectors 13Keyboard connector

Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.

Chapter 5. Installing Options 33

Connector

Description

Serial connector

Used to attach an external modem, serial printer, or other

 

devices that use a 9-pin serial connector.

Mouse connector

Used to attach a mouse, trackball, or other pointing device that

 

uses a standard mouse connector.

Parallel connector

Used to attach a parallel printer, parallel scanner, or other

 

devices that use a 25-pin parallel connector.

Ethernet connector

Used to attach an Ethernet cable for a local area network

 

(LAN).

 

Note: To operate the computer within FCC Class B limits, use

 

a Category 5 Ethernet cable.

Audio line in connector

Used to receive audio signals from an external audio device,

 

such as a stereo system. When you attach an external audio

 

device, a cable is connected between the audio line out

 

connector of the device and the audio line in connector of the

 

computer.

Audio line out connector

Used to send audio signals from the computer to external

 

devices, such as powered stereo speakers (speakers with

 

built-in amplifiers), headphones, multimedia keyboards, or the

 

audio line in connector on a stereo system or other external

 

recording device.

Microphone connector

Used to attach a microphone to your computer when you want

 

to record voice or other sounds on the hard disk if you use

 

speech-recognition software.

USB connectors

Used to attach a device that requires a Universal Serial Bus

 

(USB) connection, such as a USB scanner or USB printer. If you

 

have more than four USB devices, you can purchase a USB

 

hub, which you can use to connect additional USB devices.

Keyboard connector

Used to attach a keyboard that uses a standard keyboard

 

connector.

34 Hardware Maintenance Manual

Types 8303, 8304, and 8312

The following illustration shows the locations of the connectors on the rear of the computer.

1Serial connector 2Mouse connector 3Parallel connector 4Ethernet connector 5Audio line in connector 6Power connector 7PCI slots

8AGP slot (some models)

9 Audio line out connector 10Microphone connector 11USB connectors 12VGA monitor connector 13Serial connector 14USB connectors 15Keyboard connector

Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.

Chapter 5. Installing Options 35

Connector

Description

Serial connector

Used to attach an external modem, serial printer, or other

 

devices that use a 9-pin serial connector.

Mouse connector

Used to attach a mouse, trackball, or other pointing device that

 

uses a standard mouse connector.

Parallel connector

Used to attach a parallel printer, parallel scanner, or other

 

devices that use a 25-pin parallel connector.

Ethernet connector

Used to attach an Ethernet cable for a local area network

 

(LAN).

 

Note: To operate the computer within FCC Class B limits, use

 

a Category 5 Ethernet cable.

Audio line in connector

Used to receive audio signals from an external audio device,

 

such as a stereo system. When you attach an external audio

 

device, a cable is connected between the audio line out

 

connector of the device and the audio line in connector of the

 

computer.

Audio line out connector

Used to send audio signals from the computer to external

 

devices, such as powered stereo speakers (speakers with

 

built-in amplifiers), headphones, multimedia keyboards, or the

 

audio line in connector on a stereo system or other external

 

recording device.

Microphone connector

Used to attach a microphone to your computer when you want

 

to record voice or other sounds on the hard disk if you use

 

speech-recognition software.

USB connectors

Used to attach a device that requires a Universal Serial Bus

 

(USB) connection, such as a USB scanner or USB printer. If you

 

have more than four USB devices, you can purchase a USB

 

hub, which you can use to connect additional USB devices.

Keyboard connector

Used to attach a keyboard that uses a standard keyboard

 

connector.

36 Hardware Maintenance Manual

Types 8305, 8306, 8309, and 8313

The following illustration shows the locations of the connectors on the rear of the computer.

1Power connector 2Mouse connector 3Serial connector 4Parallel connector 5Ethernet connector 6Audio line in connector 7PCI slots

8AGP slot (some models)

9 Audio line out connector 10Microphone connector 11USB connectors 12VGA monitor connector 13Serial connector 14USB connectors 15Keyboard connector

Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.

Types 8307, 8308, 8310, 8311, 8314, and 8315

The following illustration shows the locations of the connectors on the back of the computer.

Chapter 5. Installing Options 37

1Serial connector 2Mouse connector 3Keyboard connector 4USB connectors 5Serial connector 6Parallel connector 7VGA monitor connector 8USB connectors

9 Ethernet connector 10Microphone connector 11Audio line out connector 12Audio line in connector 13AGP slot (some models) 14PCI slots

15Power connector

Note: Some connectors on the rear of the computer are color-coded to help you to determine where to connect the cables on your computer.

38 Hardware Maintenance Manual

Connector

Description

Serial connector

Used to attach an external modem, serial printer, or other

 

devices that use a 9-pin serial connector.

Mouse connector

Used to attach a mouse, trackball, or other pointing device that

 

uses a standard mouse connector.

Keyboard connector

Used to attach a keyboard that uses a standard keyboard

 

connector.

USB connectors

Used to attach a device that requires a Universal Serial Bus

 

(USB) connection, such as a USB scanner or USB printer. If you

 

have more than four USB devices, you can purchase a USB

 

hub, which you can use to connect additional USB devices.

Parallel connector

Used to attach a parallel printer, parallel scanner, or other

 

devices that use a 25-pin parallel connector.

Ethernet connector

Used to attach an Ethernet cable for a local area network

 

(LAN).

 

Note: To operate the computer within FCC Class B limits, use

 

a Category 5 Ethernet cable.

Microphone connector

Used to attach a microphone to your computer when you want

 

to record voice or other sounds on the hard disk if you use

 

speech-recognition software.

Audio line out connector

Used to send audio signals from the computer to external

 

devices, such as powered stereo speakers (speakers with

 

built-in amplifiers), headphones, multimedia keyboards, or the

 

audio line in connector on a stereo system or other external

 

recording device.

Audio line in connector

Used to receive audio signals from an external audio device,

 

such as a stereo system. When you attach an external audio

 

device, a cable is connected between the audio line out

 

connector of the device and the audio line in connector of the

 

computer.

Obtaining device drivers

Device drivers can be obtained for operating systems that are not preinstalled at http://www.ibm.com/pc/support/ on the World Wide Web. Installation instructions are provided in README files with the device driver files.

Installing internal options

The capabilities of the computer can be expanded by adding memory, drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option.

Chapter 5. Installing Options 39

Removing the cover

Types 8303, 8304, and 8312

Important: Read “Safety information” on page 271 and “Handling electrostatic discharge-sensitive devices” on page 274 before you begin.

To remove the cover:

1.Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer.

2.Unplug all power cords from electrical outlets.

3.Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.

4.Press the buttons on the sides of the computer and pivot the rear end of the cover up toward the front of the computer.

Types 8305, 8306, 8309, and 8313

Important: Read “Safety information” on page 271 and “Handling electrostatic discharge-sensitive devices” on page 274 before you begin.

To remove the cover:

1.Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer.

2.Unplug all power cords from electrical outlets.

3.Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.

40 Hardware Maintenance Manual

4.Press the buttons on the sides of the computer and pivot the rear end of the cover up toward the front of the computer.

Types 8307, 8308, 8310, 8311, 8314, and 8315

Important: Read “Safety information” on page 271 and “Handling electrostatic discharge-sensitive devices” on page 274 before you begin.

To remove the cover:

1.Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer.

2.Unplug all power cords from electrical outlets.

3.Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer.

4.Press the cover-release button on the left side cover and remove the cover.

Chapter 5. Installing Options 41

Locating components

Types 8303, 8304, and 8312

The following illustration will help you locate the various components in your computer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Power supply

 

 

 

 

 

5DIMM

2PCI slot

 

 

 

 

 

6Hard disk drive

3AGP slot (some models)

 

 

 

 

 

7CD-ROM drive or DVD-ROM drive

4Support bar

 

 

 

 

 

8Diskette drive

42 Hardware Maintenance Manual

Types 8305, 8306, 8309, and 8313

The following illustration will help you locate the various components in your computer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1CD drive or DVD drive

6 DIMMs

2USB connector

7System Board

3USB connector

8 Microprocessor and heat sink

4Hard disk drive

9PCI slots

5Diskette drive

 

 

 

 

 

 

 

 

 

 

 

Chapter 5. Installing Options 43

Types 8307, 8308, 8310, 8311, 8314, and 8315

The following illustration will help you locate the various components in your computer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1Microprocessor and heat sink

 

 

 

4PCI adapter

 

 

 

 

 

 

 

 

 

 

 

 

2DIMMs

 

 

 

5Power supply

3AGP slot (some models)

 

 

 

 

 

 

 

 

Identifying parts on the system board

Types 8303, 8304, and 8312

The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are IBM-installed or that you can install later.

44 Hardware Maintenance Manual

+ 264 hidden pages