IBM 1173-841 User Manual

PANEL1173-841

17” TFT Expandable Intel

Industrial Panel PC with 2 PCI

User’s Manual

Core™ 2 Duo

Disclaimers

This manual has been carefully checked and believed to contain accurate information. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.

AXIOMTEK reserves the right to change or revise this document and/or product at any time without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AXIOMTEK Co., Ltd.

Safety Approvals

 CE Marking  FCC Class A

 FCC Compliance

This equipment has been tested in compliance with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are meant to provide reasonable protection against harmful interference in a residential installation. If not installed and used in accordance with proper instructions, this equipment might generate or radiate radio frequency energy and cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to another outlet of a circuit that doesn’t connect with the receiver.

4. Consult the dealer or an experienced radio/TV technician for help.

格式化: 項目符號及編號

Shielded interface cables must be used in order to comply with the emission limits.

iii

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The PANEL1173-841 Series does not come equipped with

an operating system. An operating system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when

installing the internal components. Use a grounding wrist strap and place all electronic components in any staticshielded devices. Most electronic components are sensitive to static electrical charge.

3. Disconnect the power cord from the PANEL1173-841 Series

before any installation. Be sure both the system and external devices are turned OFF. A sudden surge of power could ruin sensitive components that the PANEL1173-841 Series must be properly grounded.

4. The brightness of the flat panel display will be getting weaker

as a result of frequent usage. However, the operating period varies depending on the application environment.

5. Turn OFF the system power before cleaning. Clean the

system using a cloth only. Do not spray any liquid cleaner directly onto the screen. The PANEL1173-841 Series may come with or w/o a touchscreen. Although the touchscreen is chemical resistant, it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen. In case your system comes without the touchscreen, you must follow the same procedure and not spray any cleaner on the flat panel directly.

6. Avoid using sharp objects to operate the touchscreen.

Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen.

7. The flat panel display is not susceptible to shock or vibration.

When assembling the PANEL1173-841 Series, make sure it is securely installed.

8. Do not open the system’s back cover. If opening the cover

for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:

z Before handling a board or integrated circuit, touch an

unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body.

z When handling boards and components, wear a wrist-

grounding strap, available from most electronic component stores.

Trademarks Acknowledgments

AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.

and Pentium® are registered trademarks of Intel Corporation.

Intel MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation. VIA is a trademark of VIA Technologies, Inc. SST is a trademark of Silicon Storage Technology, Inc. UMC is a trademark of United Microelectronics Corporation. Other brand names and trademarks are the properties and registered brands of their respective owners.

Table of Contents

Disclaimers........................................................................................................... ii

Safety Approvals................................................................................................. iii

Safety Precautions...............................................................................................iv

C h a p t e r 1...................................................................................1

1.1 General Description.......................................................................... 2

1.2 System Specifications...................................................................... 3

1.2.1 Main CPU Board .............................................................................. 3

1.2.2 I/O System....................................................................................... 3

1.2.3 System Specification....................................................................... 4

1.3 Dimensions....................................................................................... 6

1.4 Front View and I/O Outlets............................................................... 7

1.4.1 Front View....................................................................................... 7

1.4.2 I/O Outlets....................................................................................... 8

1.5 Package List..................................................................................... 9

C h a p t e r 2.................................................................................11

2.1 Installing the CPU and DRAM........................................................ 11

2.2 Installing the the Hard Disk Drive................................................... 14

2.3 CD-ROM Installation ...................................................................... 21

2.4 Add-on Card Installation................................................................. 22

2.5 Serial Port Interface........................................................................ 24

2.6 DVI-I............................................................................................... 24

2.7 Ethernet.......................................................................................... 26

2.8 Mountings Way – Panel/ Rack ....................................................... 27

2.8.1 Panel Mounting ............................................................................. 27

2.8.2 Rack Mounting .............................................................................. 28

C h a p t e r 3.................................................................................29

3.1 Entering Setup................................................................................ 29

3.2 Control Keys................................................................................... 30

3.3 Getting Help ................................................................................... 30

3.4 The Main Menu .............................................................................. 31

3.5 Standard CMOS Setup Menu......................................................... 32

3.6 Advanced BIOS Features............................................................... 34

3.7 Advanced Chipset Features........................................................... 40

3.8 Integrated Peripherals.................................................................... 42

3.9 Power Management Setup............................................................. 47

3.10 PnP/PCI Configuration Setup......................................................... 52

3.11 PC Health Status............................................................................ 54

3.12 Frequency/Voltage Control............................................................. 55

3.13 Load Optimized Defaults................................................................ 56

3.14 Set Supervisor/User Password ...................................................... 57

3.15 Save & Exit Setup .......................................................................... 58

3.16 Exit Without Saving........................................................................ 59

C h a p t e r 4.................................................................................61

4.1 System ........................................................................................... 61

4.2 Touch Screen................................................................................. 62

4.2.1 Specification................................................................................... 62

4.2.2 Driver Installation – Windows 2000/XP/Vista.................................... 63

4.2.3 Driver Installation - DOS ................................................................... 66

A p p e n d i x Power Supply Specification................................ 69

vii

MEMO

viii

PANEL1173-841 User’s Manual

C h a p t e r 1

Introduction

This chapter contains general information and detailed specifications of the PANEL1173-841. Chapter 1 includes the following sections:

 General Description  System Specification  Dimensions  Front View & I/O Outlets  Package List

Introduction

PANEL1173-841 User’s Manual

1.1 General Description

The PANEL1173-841 is a 17” Industrial panel PC which features

Core™ 2 Duo processor and Intel® Q965 chipset to provide

Intel powerful computing performance. This panel PC also offers the expansion ability with two PCI slots. It adopts built-in speaker and WLAN module for wireless connectivity. Further, the PANEL1173-841 fits in with Aluminum IP65/NEMA4 compliant front bezel.

Powerful computing: Intel® Core™2 Duo processor

The PANEL1173-841 features Intel FSB 1066 MHz and Intel

Q965+ICH8 chipset. It features two 1394a ports, two gigabit Ethernet ports and up to 4GB of dual-channel DDR2 system memory which deliver high computing capability for high performance-demanding applications.

Expandable for 2 PCI slots

The PANEL1173-841 has two PCI slots for expansion purpose. User can easily plug in standard half-size PCI cards such as motion card, communication card and so on.

Speaker & WLAN antenna supported

Core™ 2 Duo with a maximum of

The PANEL1173-841 features built-in speaker, optional WLAN module and antenna for wireless network connectivity.

This ideal industrial-grade panel computer PANEL1173-841 can be applied to the several of industrial or commercial projects, such as transportation, factory automation, HMI machine controller, Point Of Sales, KIOSK and more. Moreover, PANEL1173-841 provides highly reliable and highly flexible industrial-grade products in all-in-one solutions.

Introduction

PANEL1173-841 User’s Manual

1.2 System Specifications

1.2.1 Main CPU Board

z CPU

 Socket LGA775 for Intel

CoreTM 2 Duo/CoreTM Solo

Processor with FSB 533/800/1066 MHz

, max up to

E6400.

NOTE It doesn’t support the processor with FSB 1333 MHz,

and it is not recommended to use Quad-Core CPU.

z System Chipset

 Intel

z BIOS

 Phoenix-Award BIOS, 16Mbit with RPL/PXE LAN Boot ROM,

Q965 + ICH8

SmartView and Customer CMOS Backup

z System Memory

 Two 240-pin DDR2 DIMM maximum up to 4GB

z L2 Cache

 Integrated in CPU

z Bus Clock

 533/800/1066 MHz

z Watchdog Timer

 Up to 255 levels as Reset feature

1.2.2 I/O System

z Standard I/O

 Three serial ports with power, two RS-232 and one RS-

232/422/485

 One PS/2 for Keyboard and Mouse Interface  Four USB Ports 2.0 compliant  Two IEEE1394a Ports

Introduction

PANEL1173-841 User’s Manual

 One DVI-I Output

z Ethernet

 First port with i82566DM Gigabit Ethernet PHY, Second port

with RTL8111B for Gigabit/Fast Ethernet

z Audio

 HD Audio for two channels output  MIC-In, Line-Out

z Storage

 Four SATA-300 interface

z Box-Header

 One 26-pin for shared LPT/FDD(optional)

z Expansion Slot

 Two 32-bit PCI Master slots

1.2.3 System Specification

z 17” TFT LCD z Disk Drive Housing

 One built-in slim type CD-ROM dive,  One internal 3.5” drive (Optional 2 X 3.5” or 2 X 2.5” HDD)

z AC Power Supply (100V ~ 240V)

Introduction

PANEL1173-841 User’s Manual

z Heat Dispensing Design z Two slots for PCI expansion z Net Weight

 15 Kgs

z Dimension (Main Body Size)

 450mm (17.71”)(W) x 150mm (5.90”)(D) x 370mm

(14.56”)(H)

z Operation Temperature

 0℃to 40℃; Relative Humidity 50%

z Relative Humidity

 10% to 85% @ 40℃, Non-Condensing

z Altitude

 10,000 ft. (3,000 meters)

z Vibration (Operating)

 5 to 500 Hz, 1 G random

z Shock (Operating)

 10 G peak acceleration (11 msec. duration)

NOTE All specifications and images are subject to change

without notice.

Introduction

PANEL1173-841 User’s Manual

1.3 Dimensions

This diagram shows you dimensions and outlines of the PANEL1173-

841.

Introduction

PANEL1173-841 User’s Manual

1.4 Front View and I/O Outlets

1.4.1 Front View

Please refer to the following illustration for features and controls of the PANEL1173-841 front bezel.

Introduction

No Function

SEL+

SEL-

Backlight ON/OFF

PANEL1173-841 User’s Manual

1.4.2 I/O Outlets

The following figure shows the I/O locations of the PANEL1173-841.

No Connector No Connector

COM1

(RS-232/422/485)

DVI-I

Giga LAN x 2

IEEE 1394a x 2

USB v2.0 x 4

Mic-in, Line-Out

COM 2 & COM 3

(RS-232)

Power Switch

AC power

PCI slots x 2

P/S2

Introduction

PANEL1173-841 User’s Manual

1.5 Package List

The package bundled with your PANEL1173-841 should contain the following items:

z P1173-841 x 1 z AC power cord x 1 z Panel mount kit x 7 z Driver CD x1 z LGA 775 CPU Cooler x 1 z DVI TO VGA Adaptor x 1 z PS/2 Splitter – Y Cable x 1 z SATA Cable x 1 z Dual 3.5” HDD bracket kit with fan x 1 (Optional) z Small HDD Kit for 2.5” HDD (Optional) z VIA WLAN Kit (Optional)

z Rack Mount Bracket Kit x 1 (Optional)

If you can not find this package or any items are missing, please contact AXIOMTEK distributors immediately.

Introduction

PANEL1173-841 User’s Manual

MEMO

Introduction

PANEL1173-841 User’s Manual

C h a p t e r 2

Hardware Installation

The PANEL1173-841 is convenient for your various hardware configurations in flexible ways, such as CPU (Central Processing Unit), HDD (Hard Disk Drive), Memory Module (DRAM), CD-ROM, Add-On card, and more. The chapter 2 will show you how to install the hardware. It includes:

 CPU  DRAM  Hard Disk  CD-ROM  Add-On Card  Serial Port  VGA  Ethernet  Mounting Ways

2.1 Installing the CPU and DRAM

The standard PANEL1173-841 system is designed for Intel® CoreTM 2 Duo processors. The built-in CPU board provides two 240-pin DDR2 DIMM sockets that support system memory up to 4GB.

Please refer to the instructions below, illustrated with concise images, to upgrade the CPU, DRAM, PCI step by step:

Hardware Installation

PANEL1173-841 User’s Manual

Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit.

Hardware Installation

PANEL1173-841 User’s Manual

Step 3 Install the CPU and DDR DRAM in the PANEL1173-841.

DRAM

CPU

Hardware Installation

PANEL1173-841 User’s Manual

2.2 Installing the the Hard Disk Drive

The PANEL1173-841 offers a convenient drive bay module for users to install HDD. The system offers users one 3.5” Hard Disk Drives for installation. If you want to install dual 3.5” HDD, or 2.5” HDD, the PANEL1173-841 also provides the dual 3.5” and dual 2.5” drive holder to meet your requirement. Please follow the steps:

Note The hardware limitation is that the 2.5” HDD and 3.5”

HDD CAN NOT exist simultaneously.

Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit. Step 3 Unscrew 4 screws from the HDD drive bracket, and take out

HDD bracket kit to install 3.5” HDD.

Hardware Installation

PANEL1173-841 User’s Manual

Step 4 Fix the Hard Disk to the HDD bracket and connect the cable

to complete the installation.

(4-1)

(4-2)

¾ Installing Dual 3.5” HDD

If installing the dual 3.5” HDD, please follow the steps: Step 1 Change HDD bracket from 3.5” to dual 3.5”.

Hardware Installation

PANEL1173-841 User’s Manual

Step 2 Fix the Hard Disk to the HDD bracket to complete the

installation.

Hardware Installation

+ 56 hidden pages