Hyundai H-LED32V9 Instruction Manual

H-LED32V9

LED TV

ТЕЛЕВИЗОР

ЦВЕТНОГО ИЗОБРАЖЕНИЯ

ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Руководство по эксплуатации Instruction manual

Table of contents Before you start

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation

Wall mounting Stand installation

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Teletext operations OSD operation

Channel setting Picture setting Sound setting Timer setting Option setting Lock setting Hotel mode Programme guide

USB operation

General operations of playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 4 5 5 5 6 6 6 6 7 7 8 8 8

9 10 10 11 11 12 12 12 13 13 14 14 14 15 15

2 3

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit should only be connected to a wall socket having grounding.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

• Please contact the service center immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup, medicine and any container with water on this

Before you start/Installation

product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LCD TV up or down display direction.

• Do not transport it with the power cord or the connection cable connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it can be damaged.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic

drawings and may differ from of real objects.

Installation

Wall mounting

For wall mounting the back panel of this unit is equipped with 4 screw holes (4 mm diameter, 450 mm horizontal spread distance x 250 mm vertical spread distance). A wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Stand installation

Place the LED TV on a solid flat surface. Use soft material to place over the front screen to avoid any damage. Then fix the protective pad, the ring and the stand base to the stand in the bottom rear part of the cabinet:

For fixing use the 6 included screws as shown below:

4 X 14 size screws

2 X 8 size screws

Connection

Сonnection

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect a TV or CATV antenna to the

antenna jack.

• Connect a video source to the Composite

video input jack with RCA cable.

• If the video source has a SCART output jack, you can connect the signal to the monitor by the SCART cable (not included).

• Connect an audio source to the proper Audio input jacks (left and right).

• Connect PC audio input to PC main unit with related audio cable in PC mode.

• When using the unit as a computer screen,

TVRF antenna jack

connect the PC to the VGA jack of the unit by the relevant cable.

• If the video source has a HDMI output jack, you can connect the signal to the unit by HDMI cable (not included).

• Component input is intended for receiving component video signal if connected to the component output of external signal source.

• Digital output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). RCA cable should be used for connection.

Operation

Control elements

Front panel

1 2 3 4 5 6 7

Back panel

1 2

5 6 7 8 9 10 11 12

1. CH+/CH- buttons

2. VOL+/VOL- buttons

3. MENU button

4. TV/AV button

5. POWER button

6. Power indicator

7. Remote control sensor

1. HDMI inputs x 3

2. PC (VGA) input

3. Stereo audio input for Component video-1

4. Component video input-1

5. Stereo audio input for Component video-2

6. Component video input-2

7. Audio-video input-2

8. Digital audio output

9. Power cord

10. SCART1 connector

11. SCART2 connector

12. Antenna input

13. HDMI4 input

14. PC audio input

15. PCMCIA slot

16. USB1 port

17. USB2 port

18. Audio-video input-1

Operation

Remote controller (RC)

6 7

9 10 11

12 13 14

INDEX

11. Red button/

12. TEXT (

13. HOLD (

14. CANCEL (

16 17

15. SUBTITLE/SUBPAGE (

16. INFO/INDEX (

17.

button

18. AUDIO (

button

)/ button

)/ STILL button

) button

19. EXIT button

20. INDEX button

21. VOL+/VOL- buttons

22. EPG button

23. RECALL (

24. Yellow button/

25. Blue button/

26. SIZE (

) button

button

)/ZOOM ( ) button

27. RADIO button

28.

button

29. DMP button

20 21

Changing the battery

1. Remove the battery compartment cover

on the back of the RC.

22 23 24 25

26 27

28 29

2. Insert two AAA batteries batteries into the battery compartment making sure that the correct polarity is observed.

3. Install the cover back.

1. POWER button

2. Number buttons

3. SOURCE/REVEAL ( ) button

4. MENU button

5. ENTER button/cursor buttons (LEFT/RIGHT/ UP/DOWN)

6. CH+/CH- buttons

7. LIST button

8. SLEEP button

9. button

10. Green button/ button

1 2 3

• The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time. Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose RC to shock, liquids, and do not place it in an area with high humidity.

Operation Operation

General operations

• Press POWER button on the unit or on the RC to switch on the power. Press POWER button again to switch the unit into standby mode. When the unit is on, the power indicator will be green.

• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

• Press button again or adjust volume to resume sound.

• Press SLEEP button repeatedly to set the sleep time (from 10 to 240 min or off). When sleep time is set, press this button to display the time remaining until the auto turn off.

• Press AUDIO ( ) button in TV mode repeatedly to switch between Nicam Stereo, Mono, Dual I and Dual II sound modes (can be unavailable for some channels).

• Press repeatedly TV/AV button on the unit or press SOURCE button on the RC, then press UP/DOWN cursor buttons to cycle through the available source list as follows: DTV - ATV - SCART1 - SCART2_CVBS

- Component1 - Component2 - PC-RGB HDMI1 - HDMI2 - HDMI3 - HDMI4 - AV1 - AV2

- SCART2_YC.

• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number from 0 to 200 directly.

• Press RECALL ( to select from the present channel and the previously displayed channel.

• Press or «Favorite Off». When «Favorite On» is selected, press CH+/CH- buttons to select favorite channels.

• Press LIST button to call or hide the channel list.

• Press INFO button to display the preset TV channel play information.

• Press ZOOM ( ) button repeatedly to select an aspect ratio: Auto/4:3/16:9/Zoom1/ Zoom2/14:9. The set of available aspects can

button to cut off sound, press this

) button on the RC

button to select «Favorite On»

vary depending on the current signal source.

Teletext operations (option)

Select a TV channel in order to pick up the picture signal of Teletext. Teletext button functions are as follows:

TEXT ( ): Press this button to enter into TEXT mode. Press this button again to enter mixed mode. Press the button again to return to the channel you are watching.

HOLD ( ): Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX ( ): Press this button to go to the index page.

SIZE ( ): Press this button to enlarge the top part of the page. Press this button again to enlarge the bottom part of the page. Press this button third time to normal size text page view.

REVEAL ( ): Press this button to reveal the cancelled information. Press this button again to cancel the information.

SUBPAGE ( ): Press this button to select sub-page. Input the number of sub-page and use numeric buttons in the format 0001 for sub page 1. The teletext will search for the sub page. Press SUBPAGE button again to exit the subpage mode.

CANCEL ( ): Press this button to exit from the teletext mode.

Red/Green/Yellow/Blue buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower parts of teletext screen.

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/- buttons on the panel to select setting page.

3. Press DOWN cursor button on the RC or CH- button on the panel to go to the parameter list.

4. Press UP/DOWN cursor buttons on the

8 9

RC or CH+/- buttons on the panel to select a parameter to adjust.

5. Press cursor buttons on the RC or VOL+/or CH+/- buttons on the panel to adjust the selected parameter.

6. Press MENU button to return to the previous menu page. Press EXIT button on the RC to quit the menu.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real screens.

Channel setting

CHANNEL

Auto Tuning DTV Manual Tuning ATV Manual Tuning Programme Edit Signal Information CI information

Exit

• Auto tuning: press ENTER buttons to

start automatic search and saving of available ATV channels. After the search is finished, the unit will skip to searching DTV channels, Radio channels and Data. In course of ATV search, press MENU button to skip to DTV, Radio and Data search.

• DTV manual search: Press LEFT/RIGHT

cursor buttons to select channel number. Press ENTER button to start searching. When the nearest available channel is found, the search will stop and the channel will be saved under the selected number. Press EXIT button to quit.

• ATV manual search: Storage to 1: select channel number. System: select corresponding sound system. Current CH 2: search for next available

channel starting from current frequency.

Search: press LEFT/RIGHT buttons; the

Enter

unit will search for next available channel downward or upward and save it under the current number.

Fine: perform fine adjustment of the current

frequency.

• Program Edit: this item allows you to sort

TV programs according to your preferences. Enter into program edit menu:

Delete: Select the channel you want to delete.

Press red button to delete the channel.

Rename (in TV mode): Highlight the needed channel. Press green button; then press UP/ DOWN buttons to select a symbol. Press LEFT/RIGHT buttons to select the next symbol. Press green button to confirm.

Move (not available for DTV channels with LCN): Highlight the needed channel. Press yellow button; select the position to put the channel into. Press yellow button to confirm.

Skip: Highlight the needed channel. Press blue button; now this channel will be skipped when you select previous/next channels.

Favorite: Select the channel you want to edit. If this channel is your favorite channel, you can add the mark to the channel as your favorite channel by pressing button.

• Signal Information (only in DTV mode):

Display the current signal information.

• CI Information (only in DTV mode): This

function enables you to watch some encrypted services (pay services). Please insert a CI card into the PCMCIA slot according to the arrow on the CI card.

• The function can only be gotten when

CI slot is available.

• It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

• Please do not insert or pull out the CI card when power on. During initialization of the CI card, please don’t operate the TV.

• Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.

Operation

Picture setting

PICTURE

Picture Mode Colour Temp Aspect Ratio DNR Screen

Exit

• Picture Mode: Home/Vivid/Standard/

Soft/User. When User mode is selected, you can adjust contrast, brightness, saturation, sharpness and tint (in NTSC) of the image.

• Colour Temperature: Normal/Warm/User/

Cool.

• Aspect ratio: Set the picture format:

Auto/4:3/16:9/Zoom1/Zoom2/14:9.

• DNR: Dynamic noise reduction effect for

reducing the video noise level.

• Screen (only in PC-RGB mode): Auto adjust: automatical setting of the

parameters.

Horizontal Position: adjust horizontal position

of the image.

Vertical Position: adjust vertical position of

the image.

Size: adjust the image frequency manually. Phase: adjust the phase manually.

Enter

Sound setting

SOUND

Sound Mode Balance AVL Surround Sound AD Switch

Exit

• Sound mode: Standard/Music/Theater/

Sport/User. When User mode is selected, you can adjust bass and treble.

• Balance: adjust balance between left and

right speaker.

• AVL: set the auto volume correction on/

off. Volume automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time when the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.

• Surround Sound: set the surround sound

effect on or off.

• AD Switch (in DTV mode): This is an

auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off and control the volume.

Enter

+ 23 hidden pages