Hyundai H-LED24V3 Instruction Manual

ТЕЛЕВИЗОР

ЦВЕТНОГО ИЗОБРАЖЕНИЯ

ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Руководство по эксплуатации Instruction manual

LED TV

H-LED24V3

2 3

Table of contents Before you start

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read

this manual carefully before connecting, operating and/or adjusting the product and keep

the manual for reference in the future.

Table of contents

Before you start

Utilization of the product

Important safeguards

Installation/connection

Connection

Outdoor antenna connection

Other connections

Installation

Operation

Control elements

Front panel

Back panel

Remote controller

Changing the battery

General operations

AV signal sources

Teletext operations

PC screen

OSD operation

Picture setting

Sound setting

Setting

Function setting

Channel setting

PC setup

General information

Troubleshooting

Causes of interference

Accessories

Specifications

If you want to dispose this product, do not mix it with general household waste. There is

a separate collection system for used electronic products in accordance with legislation

that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so,

you will ensure that your disposed product undergoes the necessary treatment, recovery

and recycling and thus prevent potential negative effects on the environment and human

health.

Utilization of the product

Important safeguards

• Before connecting the AC power cord

to the DC adapter outlet, make sure that

the voltage designation of the DC adapter

corresponds to the local electrical supply.

• Accessories include a DC adaptor RS-

330/120-S325. Do not use other adaptors with

this unit.

• Please unplug the power cord from the AC

outlet and contact a service center for repair

if following occurs: any obvious abnormality

appears in the unit, such as smoky, peculiar

smell or strange sound; liquid has been spilled or

other objects have fallen into the unit; no picture

or sound; cover or panel is broken; although you

have operated the unit following the operating

instructions, it still cannot work normally.

• This unit should only be connected to a

wall socket having grounding.

• Always disconnect the power cord and

antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet;

also unplug the signal cables from the input

ports when the unit is unused for long periods

of time.

• When unplugging the plug, always hold

the wide slot, do not touch the metal part, and

do not destroy, refit, twist, pull or roast the

power cord.

• Please contact the service center

immediately if you found that the core is

showed in the air or has been broken.

• Please replace the AC outlet if the metal

bolt cannot be inserted into the power socket

completely or it cannot be fastened even when

it was pushed in, otherwise, any accidents of

shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket

with numerous devices jointed on one power

socket or cable device. The wire of non-

designated capacity may cause the fire due to

the generation of heat.

• All instructions must be read and

understood well before you operate the unit.

Heed all warnings and follow all instructions.

• Please use the accessories provided

by the manufacturer. Using inadequate

accessories may result in accidents.

• Please adjust the product through the

panel buttons or the remote controller, do

not remove the cover or attempt to service

the product by yourself. Do not disassemble

back cover and do not make maintenance by

yourself to avoid the electric shock.

• Over-press the panel may destroy the

product.

• Do not place the product on an unstable

cart, stand surface, tripod, bracket, or table.

The product may fall, causing serious accidents

Before you start

as well as the damage to the product.

• Please place the product on a flat surface

in a well-ventilated location. Keep it away from

the burning-light, direct sunlight, vibration,

high-temperature and humidity. Store the

product with a temperature from –20

C ~50

otherwise you may destroy the product.

• Do not place any vase, potted plant, cup,

medicine and any container with water on this

product. If the liquid is spilt, it may cause the

fire, electric shock or breakdown.

• Do not install it at the place on the strong

magnetic field or current field. It may cause

break down. This equipment may be observed

deterioration of the picture by electromagnetic

radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf

with wheels when installing this product. If it

moves or is tipped over, it may be damaged.

• Do not place any fire source such as

candlelight close to this product or place it on

this product. If it is tipped over or fallen down, it

may cause damage or fire.

• Do not place the unit into closed space

of TV for better ventilation; it can reduce the

product lifetime. Keep a space at list 10 cm at

above, left, and right of the TV.

• Please place all the signal cords behind of

rear panel.

• Do not overexert or touch the panel when

you convey the product. Do not transfer the

LCD TV up or down display direction.

• Do not transport it with the power cord

or the connection cable connected. If you

move this product with the power cord or the

connection cable connected, the damaged

power cord, connection cable or connection

terminal may cause the fire, the electric shock

or breakdown.

• 2 persons or more shall transport the

device, which is heavier than 18 kg. If you drop

or tip over the device, it may damage it.

• The temperature of the product’s body

becomes a little higher after a long period use.

This phenomenon indicates that heat exchange

in normal working mode, thus please do not

let children or anyone who is sensitive of

temperature to touch.

All images provided herein are schematic

drawings of real objects and may differ

from their real images.

Сonnection/Installation

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75 Ω

impedance converter to plug in antenna input

terminal on the rear of the cabinet.

Other connections

• Connect the audio sources (Including

DVD, VCDR, CAMCORDER and PC) to the

proper AUDIO input jacks ‘L’ and ‘R’.

• Connect the video source to the VIDEO

jack by RCA cable.

• If the video source has a SCART output

jack, you can connect the signal to the monitor

by the SCART cable.

• Component input Y/Pb/Pr is intended

to receive component video signal from the

external device.

• Insert the AC power to the DC adaptor,

then connect 12V input jack from the monitor

to it’s DC output jack.

Connection

• When using the LCD as a computer

screen, connect the PC to the VGA jack from

the monitor by the relevant cable.

• This unit has PC audio in jack. Connect

this jack to PC main unit with related audio

cable in PC mode and adjust the volume to

what you want.

• If the video source has a HDMI output

jack, you can connect the signal to the monitor

by the HDMI cable.

• Connect your headphones or earphones

(not included) to the headphone socket of

this unit. When earphones are connected, the

sound output through the built-in speakers of

this unit is mute.

75 Ohm co-axis cable

TVRF antenna jack

Antenna cable connector

Connection/Installation

Installation

Place the LED TV on a solid flat surface.

Use soft material to place over the front screen

to avoid any damage. Then position the stand

on the below angle and turn it anti-clockwise

to ensure that the stand is locked to the TV as

shown below:

To easily disassemble the TV stand,

please lift the plastic tab as shown in the

middle picture below and then turn the stand

clockwise to unlock. To avoid breaking, please

do not lift the plastic tab with too much force.

Operation

Control elements

Front panel

Back panel

1. POWER button

2. TV/AV button

3. CH+/UP cursor button

4. CH-/DOWN cursor button

5. VOL+/RIGHT cursor button

6. VOL-/LEFT cursor button

7. MENU button

8. DC power input

9. HDMI input

10. VGA input

11. PC audio input

12. SCART connector

13. Earphone output

14. TVRF antenna jack

15. Audio in (left) jack

16. Audio in (right) jack

17. Video input

18. Component (YPbPr) input

1. Power indicator

2. Remote control sensor

8 9 10 11 12 13

8 9

Operation Operation

Remote controller (RC)

1. POWER button

2. Number buttons

3. ASPECT button

4. VOL+/VOL- buttons

5. DISPLAY button

6. ENTER button/cursor buttons ( / /

/ )

7. MENU button

8. P.MODE button

9. INPUT button

10. HOLD button

11. TEXT button

12. INDEX button

13. SIZE button

14. RED button

15. GREEN button

16. AUTO button

17. MUTE button

18.

button

19. NICAM button

20. CH+/CH- buttons

21. EXIT button

22. S.MODE button

23. SLEEP button

24. PGUP button

25. PGDW button

26. SUBPAGE button

27. REVEAL button

28. CYAN button

29. YELLOW button

Changing the battery

1. Remove the battery compartment cover

on the back of the RC.

2. Insert the batteries into the battery

compartment making sure that the correct

polarity is observed.

3. Install the cover back.

• Use two AAA batteries for the RC. The RC

should be pointed at remote sensor within 8

meters and within 30 degrees at the left or the

right side.

• Take the battery out of the RC if it is not

used for a long time.

• Do not mix new and used batteries or

different types of batteries. Weak batteries can

leak and severely damage the RC.

• Do not expose the RC to shock, liquids,

and do not place it in an area with high

humidity.

1 2 3

General operations

• Press POWER button on the unit or on the

RC to switch on the power, the indication light

will be in green color. Press POWER button

again to switch off the power, and the light will

be in red color.

• The picture setup, sound setup, previous

channel can be memorized before you switch

off the unit. The unit will restart under the

previous state when you switch on it again.

• Press VOL- button repeatedly to decrease

the volume; press VOL+ button repeatedly to

increase the volume from 0 to 100.

• Press SLEEP button repeatedly to set the

sleep time (from 0 to 120 min).

• Press INPUT button on the RC to select

the TV function mode. Channel ‘1’ will appear

on the right top corner after channel searching

is completed. Press CH-/CH+ buttons to select

previous or next channels; or press number

buttons to enter a channel number directly;

or press [-/--] button until the screen displays

‘-’ or ‘--’, then use number buttons to enter a

channel number from 1 to 99.

• Press

button on the RC to select

from the present channel and the previously

displayed channel.

• Press P.MODE button repeatedly to cycle

through the available video picture modes from

the following 4 types: Personal => Standard =>

Movie => Vivid.

• Press S.MODE button repeatedly to

cycle through the available sound modes from

the following 4 types: Music => Personal =>

Standard => Movie.

• Press MUTE button to cut off sound, press

this button again or adjust volume to resume

sound.

• Press DISPLAY button to display the

preset TV channel play information.

• Press ASPECT button repeatedly to select

a screen display size from the available list: Full

=> ZOOM => Subtitle => 4:3 => 14:9 => Auto.

Available aspects may differ for different

signal sources.

AV signal sources

Press INPUT button on the RC, then press

/ cursor buttons to cycle through

the available source list as follows: ATV -

HDMI - SCART - YPBPR - AV - VGA . Press

cursor button to confirm.

TELETEXT operations (option)

• Press INPUT button to select the TV

mode. Then press CH-/CH+ buttons to select

TV channel in order to pick up the picture

signal of TELETEXT.

• Press PGUP/PGDW buttons to select the

previous page or the next page; use number

buttons and the [-/- -] button to enter into a page.

• Teletext button functions are as follows:

TEXT: Press TEXT button to enter into

TEXT mode. Press this button again to return

to the channel you are watching.

PGDW: Press this button to view the next

teletext page’s program.

PGUP: Press this button to view the previous

teletext page’s program.

HOLD: Press this button to stop the move to

the next page, and the hold symbol will appear

in the top left hand corner of the screen. Press

this button again to cancel operation.

INDEX: Press this button to go to the index

page.

SIZE: Press this button to enlarge the text

shown on the teletext screen, and one half of

page could be shown.

Press this button again to view the second

half of this page.

Press this button third time to normal size

text page view.

REVEAL: Press this button to reveal the

cancelled information. Press this button again

to cancel the information.

SUBPAGE: Press this button to select sub

page, and the sub-page symbol will appear in

the left top hand corner of the screen. Enter the

number of sub page and use numeric buttons

in the format 0001 for sub page 1. The teletext

will search for the sub page.

Red/Green/Yellow/Blue buttons: Press

these 4 color buttons to access directly to

Operation

corresponding color page displayed at the

lower parts of teletext screen.

PC screen

Select the VGA input (TV into PC) mode.

The unit has a VGA jack for a normal

computer. Connect the monitor with a PC

by this jack and the unit can be used as the

monitor for the PC.

OSD operation

Press MENU button on the RC to enter the

OSD menu. Use use

/ buttons to select a

setting page displayed on the screen. Press

/ buttons to go to the needed

item, then use

/ buttons to select available

setting or to adjust the selected item. Press

ENTER button to confirm

After setting, press MENU button to return

to the root menu or press EXIT button to exit

menu setting.

Picture setting

PICTURE

MOVE SELECT EXIT

PICTURE MODE

CONTRAST

BRIGHTNESS

COLOR

TINT

SHARPNESS

COLOR TEMP.

NOISE REDUCTION

• Picture Mode: Personal/Standard/Movie/

Vivid.

• Contrast

• Brightness

• Color

• Tint: adjust the tone of color when your

system is in NTSC.

• Sharpness

• Color Temperature: Normal/Warm/Cool.

• Noise reduction: Digital noise reduction

effect for reducing the video noise level: Off/

On, if the broadcast signal received is weak.

Sound setting

SOUND

MOVE SELECT EXIT

SOUND MODE

BASS

TREBLE

BALANCE

AVL

• Sound Mode: Music/Personal/Standard/

Movie.

• Bass

• Treble

• Balance: adjust output between left and

right speakers.

• AVL: set the auto volume leveller on/off.

Setting

SETTING

MOVE SELECT EXIT

LANGUAGE

OSD TIMER

TRANSPARENCE

OVERSCAN

RESET

• Language: select an OSD menu language

• OSD Timer: select OSD menu display last

time.

• Transparence: set the level of the OSD

window transparence.

• Overscan: set ON or OFF enlargement

of the OSD window (function available only in

+ 21 hidden pages