Hyundai H-LED24V11 Instruction Manual

H-LED24V11

LED TV

ЦВЕТНОГО ИЗОБРАЖЕНИЯ

ТЕЛЕВИЗОР

ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Руководство по эксплуатации Instruction manual

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards Installation

Base installation Wall mounting

Connection

Outdoor antenna connection Other connections

Operation

Control elements

Front panel

Back panel Remote controller

Changing the battery

General operations

Signal sources OSD operation

Picture setting Sound setting OSD setting

TV setting USB operation

General operations of file playback

General information

Troubleshooting

Causes of interference Accessories Specifications

2 3 3 3 4 4 4 5 5 5 6 6 6 6 7 7 8 8 8 9 9 9

9 10 11 12 12 12 13 13

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Before connecting the AC power cord to the mains supply outlet, make sure that the voltage designation of the unit corresponds to the local electrical supply.

• Please unplug the power cord from the AC outlet and contact a service center for repair if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

• This unit should only be connected to a wall socket having grounding.

• Always disconnect the power cord and antenna during a storm.

• Do not fix the power cord with a metal nail.

• Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

• When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

• Please contact the service center immediately if you found that the core is showed in the air or has been broken.

• Please replace the AC outlet if the metal

bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

• Never touch the antenna lie or power plug

if it stars to thunder.

• Do not touch the power plug with wet

hands.

• Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

• All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

• Please use the accessories provided by the manufacturer. Using inadequate accessories may result in accidents.

• Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

• Over-press the panel may destroy the product.

• Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

• Please place the product on a flat surface in a well-ventilated location. Keep it away from

Before you start

the burning-light, direct sunlight, vibration, high-temperature and humidity.

• Do not place any vase, potted plant, cup, medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

• Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

• Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

• Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

• Do not place the unit into closed space of TV for better ventilation; it can reduce the product lifetime. Keep a space at least 10 cm at above, left, and right of the TV.

• Please place all the signal cords behind of rear panel.

• Do not overexert or touch the panel when you convey the product. Do not transfer the LED TV up or down display direction.

• Do not transport it with the power cord or cables connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

• 2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

• The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic drawings of real objects and may differ from their real images.

Installation

Base instalation

Cover an even stable surface with a soft cloth. Place the TV unit facedown on the cloth. Align the holes in the stand with the fixing holes in the bottom of the TV casing rear panel. Fix the stand to the casing by fastening the 4 supplied screws.

Wall mounting

For wall mounting the back panel of this unit is equipped with 4 screw holes (4 mm diameter, 100 mm horizontal spread distance x 100 mm vertical spread distance). A wall-mount bracket should be used for wall mounting (the bracket is not included and should be acquired separately). Manufacturer is not responsible for improper mounting resulting in damage of the unit.

Connection

Before you start

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

• Connect a video source to the Composite

video input jack with RCA cable.

• Connect an audio source to the proper

Audio input jacks (Left and Right).

• When using the unit as a computer screen, connect the PC to the VGA jack of the unit by the relevant cable.

• Connect PC audio input to PC main unit with related audio cable in PC mode.

• If the video source has a HDMI output jack, you can connect the signal to the unit by HDMI cable (not supplied).

• Component input is intended for receiving

TVRF antenna jack

component video signal if connected to the component output of external signal source. To receive audio signal for component video, please use Left and Right stereo audio inputs for component video.

• Connect an external device (e.g., VCR-/ DVD-recorder) to the proper Audio/Video output jacks of this unit with AV RCA cable.

• Connect your headphones or earphones (not included) to the headphone socket of this unit. When headphones are connected, the sound output through the built-in speakers of this unit is mute.

• SPDIF digital output is intended for transmitting multi-channel sound to an external decoder (e.g. in 5.1-CH format). RCA cable should be used for connection.

Operation

Control elements

Front panel

Back panel

1. SOURCE button

2. CH+/CH- buttons

3. VOL+/VOL- buttons

4. Power cord socket

5. MENU button

6. Power switch*

7. Standby button

8. USB-1 port

9. USB-2 port

10. SPDIF digital output

11. Antenna jack

12. HDMI-1 input

13. Headphone output

14. HDMI-2/HDMI-3 inputs

15. Pb/Cb and Pr/Cr jacks of Component input

16. Y jack of Component input/Composite input-2

17. Audio stereo input for Component video and for Composite video input-2

18. Audio stereo input-1

19. Composite video input-1

20. VGA input

21. PC audio input

22. Video output

23. Audio stereo output

5 6 7

1. Display

2. IR sensor/Power indicator

*Positions of the Power switch:

power on power off

Operation

Remote controller (RC)

3 4 5

6 7

8 9

10 11 12 13

1. POWER button

2. Number buttons (Alphabetic function is unavailable for this model)

3. F1 button

4. SMART S. button

5. MENU button

6. VOL+/VOL- buttons

7. Cursor (UP/DOWN/LEFT/RIGHT) buttons/

17 18 19

21 22

23 24

25 26

OK button

8. TIME button

9. INFO button

10. Button not operable

11. COLOR button

12. PLAY button

13. PAUSE button

14. PREV/NEXT buttons

15. Button not operable

16. MUTE button

17. PROGRAM LIST button

18. SMART P. button

19. SOURCE button

20. CH+/CH- buttons

21. RETURN button

22. 16:9 button

23. AUDIO button (option)

24. P/N button

25. ROTATE button

26. STOP button

27. REV/FWD buttons

Changing the battery

1. Remove the battery compartment cover on the back of the RC.

2. Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3. Install the cover back.

• Use 2 x AAA (1.5 V) batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

• Take the battery out of the RC if it is not used for a long time.

• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

• Do not expose the RC to shock, liquids, and do not place it in an area with high humidity.

Operation

General operations

• Connect the terminal of the power cord to the power cord socket of the TV (the position of the socket is given in paragraph Control Elements above). Connect the plug of the power cord to the power supply outlet and then set the power switch on the rear panel to the on position, the power indicator will light up in blue showing that the unit is in standby mode. To switch on the unit, press STANDBY button on the panel or POWER button on the RC; when the TV is on, the power indicator is off. Press this button again to switch the unit to the standby mode, the power indicator will light up in blue. To switch off the unit completely, set the power switch on the rear panel to the off position and then disconnect the power cord plug from the power supply outlet.

When no signal input for 5 minutes, the

unit will switch to standby mode automatically.

• Press VOL- button repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

• Press TIME button repeatedly to set the sleep time (from 15 to 240 min).

• Press RETURN button on the RC to select from the present channel and the previously displayed channel.

• Press 16:9 button repeatedly to select a screen display size from the available list: FULL => 4:3 => SUBTITLE => FILM. Available aspects may differ for different signal sources.

• Press MUTE button to cut off sound, press this button again or adjust volume to resume sound.

• Select the TV function mode. Press CH-/CH+ buttons to select previous or next channels; or press number buttons to enter a channel number directly.

• Press SMART P. button repeatedly to cycle through the available video picture modes from the following types: Standard => Soft => User => Bright.

• Press SMART S. button repeatedly to cycle through the available sound modes from

the following types: Standard => Music => Movie => User.

• Press INFO button to display the preset

TV channel play information.

• Press P/N button to select PAL/NTSC/

SECAM/Auto color system.

• Press COLOR button to select Standard/

Warm/Cool color temperature mode.

• Press F1 button to freeze the picture on

or off.

• Press PROGRAM LIST button to scan or

set program list.

• Press AUDIO button in TV mode repeatedly to switch between various Nicam sound modes (can be unavailable for some channels). This function is optional.

Signal sources

Press SOURCE button, then press DOWN/ UP cursor buttons on the RC or CH+/CHbuttons on the panel to select a source from available source list: TV => AV1 => AV2 => YPbPr => PC=> HDMI1 => HDMI2 => HDMI3 => USB1 => USB2. Press OK button on the RC or MENU button on the panel to confirm.

OSD operation

1. Press MENU button to enter the setting

menu displayed on the screen.

2. Press LEFT/RIGHT cursor buttons on the RC or VOL+/VOL- buttons on the panel to go to the needed setting page.

3. Press UP/DOWN cursor buttons on the RC or CH+/CH- buttons on the panel to select a parameter to adjust.

4. Press LEFT/RIGHT buttons on the RC or VOL+/VOL- buttons on the panel to adjust the selected parameter.

5. Press MENU button to return to the root menu or exit menu setting.

Some menu items may be in grey color, in this case they are not adjustable. Pictures of OSD menu are for reference only; they may differ from the real pictures.

Operation

Picture setting

Picture mode Contrast Brightness Saturation Hue Sharpness Aspect ratio Color temp. Noise reduction

Adjust Select Menu:Exit

• Picture Mode: Standard/Soft/User/Bright.

• Contrast, Brightness, Saturation, Hue

(available only for NTSC system), Sharpness.

• Aspect ratio: Full/4:3/Subtitle/Film.

• Color temperature: Select color

temperaure mode of the picture - Standard/ Warm/Cool.

• Noise Reduction: Middle/High/Low/Off

level of noise reduction.

Sound setting

Sound mode Treble Bass Balance Auto volume

Adjust Select Menu:Exit

• Sound Mode: Standrard/Music/Movie/

User.

• Bass, Treble, Balance (adjust output

between left and right speakers).

• Auto volume: set the auto volume

correction on/off.

OSD setting

OSD language OSD duration OSD transparency Blue screen Sleep time Recall

Adjust Select Menu:Exit

• OSD-Language: select the language of

the on-screen menu.

• OSD-Duration: set OSD menu display

time from 15 to 60.

• OSD-Transparency: adjust the halftone of

the OSD menu from 0 to 100.

• Blue screen: set on or off blue screen.

• Sleep-timer: set the sleep time in minutes

(from 15 to 240 minutes).

• Recall: reset the parameters to initial

factory settings.

TV setting

Color system Sound system Skip Auto search Manual search Fine tune Channel edit

Adjust Select Menu:Exit

• Color system: PAL/NTSC/SECAM/AUTO.

• Sound system: select sound system: I,

D/K, M, B/G.

• Skip: set on or off skipping a channel.

• Auto search: press RIGHT cursor button

+ 20 hidden pages