Hyundai H-LCD2216 Instruction Manual

H-LCD2216

ТЕЛЕВИЗОР ЦВЕТНОГО ИЗОБРАЖЕНИЯ LCD TV ЖИДКОКРИСТАЛЛИЧЕСКИЙ

(LCD)

Instruction manual

Руководство по эксплуатации

Table of contents

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents	2
Before you start	3
Utilization of the product	3
Important safeguards	3
Installation and connection	5
Connection	5
Outdoor antenna connection	5
Other connections	5
Operation	6
Control elements	6
Front panel	6
Back panel	6
Remote controller	7
Changing the battery	7
General operations	8
Signal sources	8
Teletext operations	8
PC screen	9
OSD operation	9
Picture setting	9
Sound setting	9
Setting	9
Function setting	10
Channel setting	10
PC setup	12
Picture setup	12
General information	13
Troubleshooting	13
Causes of interference	13
Accessories	14
Specifications	14

Before you start

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

•Please unplug the power cord from the AC outlet and contact a service center for repair

if following occurs: any obvious abnormality appears in the unit, such as smoky, peculiar smell or strange sound; liquid has been spilled or other objects have fallen into the unit; no picture or sound; cover or panel is broken; although you have operated the unit following the operating instructions, it still cannot work normally.

•This unit should only be connected to a wall socket having grounding.

•Always disconnect the power cord and antenna during a storm.

•Do not fix the power cord with a metal nail.

•Unplug the power cord from the AC outlet; also unplug the signal cables from the input ports when the unit is unused for long periods of time.

•When unplugging the plug, always hold the wide slot, do not touch the metal part, and do not destroy, refit, twist, pull or roast the power cord.

•Please contact the service center immediately if you found that the core is showed in the air or has been broken.

•Please replace the AC outlet if the metal bolt cannot be inserted into the power socket completely or it cannot be fastened even when it was pushed in, otherwise, any accidents of shocks and fires would happen.

•Never touch the antenna lie or power plug if it stars to thunder.

•Do not touch the power plug with wet hands.

•Do not use any non-rated power socket with numerous devices jointed on one power socket or cable device. The wire of nondesignated capacity may cause the fire due to the generation of heat.

•All instructions must be read and understood well before you operate the unit. Heed all warnings and follow all instructions.

•Please use the accessories provided

by the manufacturer. Using inadequate accessories may result in accidents.

•Please adjust the product through the panel buttons or the remote controller, do not remove the cover or attempt to service the product by yourself. Do not disassemble back cover and do not make maintenance by yourself to avoid the electric shock.

•Over-press the panel may destroy the product.

•Do not place the product on an unstable cart, stand surface, tripod, bracket, or table. The product may fall, causing serious accidents as well as the damage to the product.

•Please place the product on a flat surface in a well-ventilated location. Keep it away from the burning-light, direct sunlight, vibration, high-temperature and humidity. Store the product with a temperature from –200C ~500C; otherwise you may destroy the product.

Before you start

•Do not place any vase, potted plant, cup, medicine and any container with water on this product. If the liquid is spilt, it may cause the fire, electric shock or breakdown.

•Do not install it at the place on the strong magnetic field or current field. It may cause break down. This equipment may be observed deterioration of the picture by electromagnetic radiation in electromagnetic environment.

•Fasten the wheel of the product or shelf with wheels when installing this product. If it moves or is tipped over, it may be damaged.

•Do not place any fire source such as candlelight close to this product or place it on this product. If it is tipped over or fallen down, it may cause damage or fire.

•Do not place the unit into closed space

of TV for better ventilation; it can reduce the product lifetime. Keep a space at list 10 cm at above, left, and right of the TV.

•Please place all the signal cords behind of rear panel.

•Do not overexert or touch the panel when you convey the product. Do not transfer the LCD TV up or down display direction.

•Do not transport it with the power cord

or the connection cable connected. If you move this product with the power cord or the connection cable connected, the damaged power cord, connection cable or connection terminal may cause the fire, the electric shock or breakdown.

•2 persons or more shall transport the device, which is heavier than 18 kg. If you drop or tip over the device, it may damage it.

•The temperature of the product’s body becomes a little higher after a long period use. This phenomenon indicates that heat exchange in normal working mode, thus please do not let children or anyone who is sensitive of temperature to touch.

All images provided herein are schematic drawings of real objects and may differ from their real images.

Installation and connection

Connection

Antenna cable connector

75 Ohm co-axis cable

Outdoor Antenna Connection

Use 75Ω coaxial cable plug or 300-75Ω impedance converter to plug in antenna input terminal on the rear of the cabinet.

Other connections

•Connect the audio sources (Including DVD, VCDR, CAMCORDER and PC) to the proper AUDIO input jacks ‘L’ and ‘R’.

•Connect the video source to the VIDEO jack by RCA cable.

•If the video source has a SCART output jack, you can connect the signal to the monitor by the SCART cable.

•Connect the video source to the S-VIDEO input jack of the monitor by the S-video cable (provided that the video source has S-video output jack).

•When using the LCD as a computer screen, connect the PC to the VGA jack from

TVRF antenna jack

the monitor by the relevant cable.

•This unit has PC audio in jack. Connect this jack to PC main unit with related audio cable in PC mode and adjust the volume to what you want.

•If the video source has a HDMI output jack, you can connect the signal to the monitor by the HDMI cable.

•Connect your headphones or earphones (not included) to the headphone socket of this unit. When earphones are connected, the sound output through the built-in speakers of this unit is mute.

Operation

Control elements

Front panel

			Power indicator
	Back panel
	1		8
	1
	2		9
	3
	4		10
	4
	5		11
	6		11
	6		12
			12
	7		13
			14
			15
			16
			17
1.	POWER button	7. VOL+ button	13. Audio (right) input
2.	SOURCE button	8. HDMI input	14. Audio (left) input
3.	MENU button	9. VGA input	15. PC audio input
4.	CHbutton	10. SCART connector	16. Headphone output
5.	CH+ button	11. S-Video input	17. TVRF antenna input
6.	VOLbutton	12. Composite video input

Operation

Remote controller (RC)

1	17
2
3
	18
4	19
5	20
6
7
8	21
9	22
10	23
11	24
12	25
13	26
14	27
15	28
16	29

1.POWER button

2.SLEEP button

3.Number buttons

4.P.MODE button

5.SOURCE button

6.OK button

7.Cursor buttons ( / //)

8.VOL+/VOLbuttons

9.INFO button

10.EXIT button

11.CANCEL button

12.TTX/MIX button

13.REVEAL button

14.INDEX button

15.GREEN button

16.RED button

17.MUTE button

18. button

19.S.MODE button

20.MENU button

21.PROGRAM+/PROGRAMbuttons

22.ASPECT button

23.AUDIO I/II button

24.SIZE button

25.HOLD/FAV button

26.SUBPAGE button

27.SUBTITLE button

28.YELLOW button

29.CYAN button

Changing the battery

1.Remove the battery compartment cover on the back of the RC.

2.Insert the batteries into the battery compartment making sure that the correct polarity is observed.

3.Install the cover back.

•Use two AAA batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.

•Take the battery out of the RC if it is not used for a long time.

•Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.

•Do not expose the RC to shock, liquids, and do not place it in an area with high

humidity.

Operation

General operations

•Press POWER button on the unit or on the RC to switch on the power, the indication light will be in blue color. Press POWER button again to switch off the power, and the light will be in red color.

•Press VOLbutton repeatedly to decrease the volume; press VOL+ button repeatedly to increase the volume.

•Press SLEEP button repeatedly to set the sleep time (from 0 to 120 min). To check the remaining sleep time, press SLEEP button; the time remaining until the unit is off will be displayed.

•Select the TV function mode. Press PROGRAM-/PROGRAM+ buttons on the RC or CH-/CH+ buttons on the unit to select previous or next channel; or press number buttons to enter a channel number directly; or press [-/--] button until the screen displays ‘-’ or ‘--’, then use number buttons to enter a channel number from 1 to 99.

•Press button on the RC to select from the present channel and the previously displayed channel.

•Press P.MODE button repeatedly to cycle through the available video picture modes from the following 4 types: Standard => Movie => Vivid => Personal.

•Press S.MODE button repeatedly to cycle through the available sound modes from the following 4 types: Standard => Movie => Music => Personal.

•Press MUTE button to cut off sound, press this button again or adjust volume to resume sound.

•Press INFO button to display the preset TV channel play information including channel number, color/sound system, etc.

•Press ASPECT button repeatedly to select a screen display size from the available list: Full => Zoom => Subtitle => 4:3 => 14:9 => Auto. Available aspects may differ for different signal sources.

•This function is only available if the

channel has NICAM signal. Press AUDIO I/II button on the RC repeatedly to select mono/ NICAM mono/stereo/Main dual/SUB dual, depending on the NICAM signal style.

Signal sources

Press SOURCE button on the RC, then press / cursor buttons to cycle through the available source list as follows: TV - HDMI - SCART - AV - S-VIDEO - VGA. Press cursor button or OK button to confirm.

Teletext operations

•In TV mode select a TV channel in order to pick up the picture signal of Teletext.

•Teletext button functions are as follows: Press number buttons (0~9) on the RC to

select a teletext of corresponding number. Press / buttons to go the previous or next teletext page.

TTX/MIX: Press this button to enter into Teletext mode. Press this button again to display TV image and teletext at the same time. Press this button again to exit Teletext mode.

CANCEL: Press this button to hide the teletext page content. Press this button again to display the content.

SIZE: Press this button to enlarge the content of upper part of the page. Press this button again to enlarge the content of lower part of the page. Press this button third time for normal size text page view.

HOLD/FAV: Press this button to stop the move to the next page. Press this button again to cancel operation.

INDEX: Press this button to go to the index page.

REVEAL: Press this button to reveal the concealed information. Press this button again to hide the information.

SUBPAGE: Press this button to select subpage (if available). Enter the number of subpage. The teletext will search for the sub page.

Red/Green/Yellow/Cyan buttons: Press these 4 color buttons to access directly to corresponding color page displayed at the lower part of teletext screen.

Operation

PC screen

Select the VGA input (TV into PC) mode. The unit has a VGA jack for a normal computer. Connect the monitor with a PC by this jack and the unit can be used as the monitor for the PC.

OSD operation

Press MENU button on the RC to enter the

OSD menu. Use use / buttons to select a setting page displayed on the screen. Press / buttons to go to the needed

item, then use / buttons to select available setting or to adjust the selected item. Press OK button to confirm

After setting, press MENU button to return to the root menu or press EXIT button to exit menu setting.

Picture setting

PICTURE

PICTURE MODE

CONTRAST

BRIGHTNESS

COLOR

TINT

SHARPNESS

COLOR TEMP.

NOISE REDUCTION

MOVE

SELECT

EXIT

•Picture Mode: Personal/Standard/Movie/ Vivid.

•Contrast

•Brightness

•Color

•Tint: adjust the tone of color when your system is in NTSC.

•Sharpness

•Color Temperature: Normal/Warm/Cool.

•Noise reduction: Digital noise reduction effect for reducing the video noise level: Off/

On, if the broadcast signal received is weak.

Sound setting

SOUND

SOUND MODE

BASS

TREBLE

BALANCE

AVL

MOVE

SELECT

EXIT

•Sound Mode: Music/Personal/Standard/ Movie.

•Bass

•Treble

•Balance: adjust output between left and right speakers.

•AVL: set the auto volume leveller on/off.

Setting

SETTING

LANGUAGE

OSD TIMER

TRANSPARENCE

OVERSCAN

RESET

MOVE

SELECT

EXIT

•Language: select an OSD menu language

•OSD Timer: select OSD menu display last time.

•Transparence: set the level of the OSD window transparence.

•Overscan: set ON or OFF enlargement

of the OSD window (function available only in HDMI source).

• Reset: setting to the factory default.

+ 20 hidden pages