Hyundai H-CDM8042 User Manual [ru]

H-CDM8042

CD/MP3/WMA-РЕСИВЕРCD/MP3/WMA RECEIVER

Руководство по эксплуатации Instruction manual

Table of contents Before you start

Dear customer!

Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Table of contents Before you start

Utilization of the product Important safeguards

Installation/Connection

Installation

General notes Din Front/Rear-Mount

1. DIN front-mount (Method A) Dismantling the unit Trim frame installation

2. DIN rear-mount (Method B) Detachable control panel Anti-theft system

Connection

Connection diagram ISO connection table

Operation

Control elements

Front panel Inner panel LCD layout General operations

Turning on/off

Volume control

Mute function

Audio parameter setting

Beep

Loudness

Mode setting

AUX in jack Radio operations

Band selection

Automatic tuning

Auto memory store

Preset scan

RDS function

AF (Alternative Frequencies)

function

TA (Traffic Alarm)/TP function

PTY (Program Type)

Other parameter setting

REG (Regional) functon

Mono/stereo control

Local radio statino search

Other parameter setting

Disc/USB/SD/MMC operations

USB/SD/MMC notes

Insert/Eject disc

Inserting an SD/MMC card/

USB device

Stopping playback

Previous/net track

Fast forward/rewind

Playback modes

File/folder search

Notes on MP3 and WMA

Notes on creating your own CD-Rs

or CD-RWs containing MP3 files

General information

Handling compact discs

Cleaning discs

Cleaning the unit body

Accessories

Troubleshooting guide

Specification 9 9 9 9 9 9 9

10 10 10

10 10 10 10 10 11 11 11 11 11

11 11 12 12 12 12 12

13 14 14 14 14 14 15 16

2 3

Utilization of the product

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Important safeguards

• Read carefully through the manual to

familiarize yourself with this unit.

• Keep this manual handy as a reference for operating procedures and precautions. Do not allow persons who have not read through this manual to use this unit.

• “CLASS 1 LASER PRODUCT”

This product contains a laser diode of higher class than 1. Laser beams from the optical pickup are dangerous to the eyes. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

• Do not allow this unit to come into contact with liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids or dust. Protect this unit from moisture.

• Make sure that foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock or laser beam exposure.

• The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.

• Using the unit with the temperature that goes beyond the operation temperature greatly

decreases the operation resource of the screen and other components of the unit and can result in an outage.

• Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.

• The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please ensure it before installation.

• When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.

• Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

• Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.

• Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Let a qualified technician check the system.

• Always keep the volume low enough so that you can hear sounds from outside the vehicle.

• Should this product fail to operate properly, contact your dealer or nearest service center.

Installation/Connection

Installation

General notes

• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.

• Before finally installing the unit, connect the wiring and make sure that the unit works properly.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

• If installation angle exceeds 30° from horizontal, the unit may not perform properly.

• Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

Din Front/Rear-Mount

This unit can be properly installed either from ‘Front’ (conventional DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilizing threaded screw Holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

1. DIN front-mount (Method A)

1. Car dashboard

2. Sleeve

3. Screw

4. Nut (5 mm)

5. Spring washer

6. Screw (5 х 25 mm)

7. Metal strap

8. Flat washer

182

1. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.

2. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.

3. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.

4. Make the necessary wire connections. Ensure the connections are correct.

5. Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

a – Trim frame b – Frame uninstall direction c – Release key insertion

Installation/Connection

1. Switch off the unit and detach the front

panel.

2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it.

3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap.

Trim frame installation

To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first.

2. DIN rear-mount (Method B)

For this method, use the screw holes in the lateral sides of the unit. Fix the unit with the help of the factory radio mounting brackets.

1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side.

2. Screw.

3. Factory radio mounting brackets.

4. Vehicle dashboard.

5. Lock (remove this part).

The outer trim frame and mounting

sleeve are not used for method of installation.

Detachable control panel

Insert the left locker of the body into the fixing hole on the side of the panel, then insert the right locker into the right hole of the panel. Press on the upper part of the panel until a click.

To detach the front panel, press OPEN button. Hold the panel at 45 degree angle and push it to the left to detach the right locker. Then detach the left locker.

The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

Anti-theft system

The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft.

Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you.

Installation/Connection

Connection

Connection diagram

Fuse

Line-out left (White)

ISO connector

ISO connection table

Location

Connector A

1 2 3 4 5 6 7 8

Battery 12V (+)/yellow Power Antenna/Blue Dimmer/Orange ACC+/Red Ground/Black

Line-out right (Red)

Antenna jack

Connector A

1. -

2. -

3. -

4. Memory +12V

5. Auto antenna output

6. To dimmer control

7. +12V (to ignition key)

8. Ground

Function

Connector B

1. Rear right speaker (+)

2. Rear right speaker (-)

3. Front right speaker (+)

4. Front right speaker (-)

5. Front left speaker (+)

6. Front left speaker (-)

7. Rear left speaker (+)

8. Rear left speaker (-)

Connector B Rear Right(+)---Violet Rear Right(-)---Violet/Black Stripe Front Right(+)---Grey Front Right(-)---Grey/Black Stripe Front Left(+)---White Front Left((-)---White/Black Stripe Rear Left(+)---Green Rear Left(-)---Green/Black Stripe

Power antenna wire is intended for power supply of the antenna and for remote control of

an additional amplifier.

Control elements

Operation

Front panel

1. PWR/MUTE button

2. MODE button

3. VOLUME knob

4. button

5. Display

6. MEM button

1 2 3 4 5 6 7 8

13 12 11 10 9

7. OK button

8. OPEN button

9. USB slot

10. AUX in jack

11. button

12. BAND button

13. SEL button

Inner panel

1 2 3 54

1. SD/MMC memory card slot

2. EJECT button

3. Panel status indicator

4. RESET button (hole)

5. Disc slot

Pressing RESET hole will erase the

clock setting and stored stations.

Panel status indicator lights up when you slide the panel down, flashes when you remove the panel.

Operation Operation

LCD layout

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

16 17

18 19 20 21 22 23 24

25 26 27

1. WMA playback indicator

2. TA function indicator

3. Digit display

4. TP function indicator

5. Equalizer graphic indicator

6. Not active

7. Disc playback indicator

8. PTY function indicator

9. Intro playback indicator

10. EON function indicator

11. Repeat playback indicator

12. AF function indicator

13. Random playback indicator

14. Mute function indicator

8 9

15. Preset station number

16. Stereo reception indicator

17. Local reception indicator

18. Active equalizer mode indicator

19. MP3 playback indicator

20. USB connection indicator

21. Memory card connection indicator

22. Not active

23. Not active

24. Subwoofer indicator (not active)

25. CD playback indicator

26. Not active

27. Not active

28. Loudness indicator

General operations

Turning on/off

Press any button (except OPEN button) to turn on the unit. Press and hold PWR/MUTE button to switch the unit off.

After the unit is off, the volume level and radio current settings will be memorized, and when you turn the unit on it will resume the stored status you previously set. To protect your ear from too loud sound, the unit volume level will turn to 50 automatically when you turn the unit on if currect volume level setting is above 50 when your turn the unit off.

Volume control

Rotate VOLUME knob to adjust the volume

level.

Mute function

Press PWR/MUTE button to turn the sound

off. Press it again to turn the sound on.

LOUD ON/LOUD OFF. LOUD function is to emphasize the bass output; the word LOUD ON indicates that the LOUD mode is on.

Mode setting

Press MODE button to select between unit operation modes: TUNER => CD => SD => USB => AUX.

USB, CARD, DISC modes will only show on the display when a USB device, memory card or a disc is inserted into the unit.

AUX jack

AUX-in jack is intended for connecting an external audio or video equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be translated through the acoustics of the head unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3-player to listen to tracks using the car acoustic system.

Audio parameter setting

Press repeatedly SEL button to select the audio settings: VOLUME => BASS => TREBLE => BALANCE => FADER=> DSP. Rotate VOLUME knob to adjust each setting.

For DSP: Choose DSP OFF => FLAT => CLASSICS => POP => ROCK => DSP OFF.

If the unit is turned off, all the settings of each mode will be saved. If cutting off battery power or resetting the unit, all the settings will return to factory default settings.

Beep

Press and hold SEL button to select BEEP ON; rotate VOLUME knob to toggle between BEEP ON (beep sound will be heard when buttons are pressed) and BEEP OFF.

Loudness

Press and hold SEL button, then press it repeatedly to select LOUD ON (LOUD OFF). Rotate VOLUME knob to select between

Radio operations

Band selection

Press repeatedly BAND button to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1 (M1), AM2 (M2). In each set of the bands you can store up to 6 preset stations, making total 30 preset memory stations.

Automatic tuning

To find a station, select a band first, then press and hold downward/upward search will start. It will play when a station is found.

/ buttons, the automatic

Programming preset stations

• To store a station: Select a band (if needed); find a station by automatic tuning. Then press MEM button and rotate VOLUME knob to choose a memory position (1-6), and finally press OK button to confirm.

• To recall a station: Select a band (if

Operation

needed); press MEM button and rotate VOLUME knob to choose a number under which the needed station is stored (1-6), and finally press OK button to recall the station.

Auto memory store

Select a band, press and hold OK button to enter auto store mode. The radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto store, press this button again.

During auto station preset, the unit will search and store stations with the strong signal first, and then weaker signal stations until the memories are full.

Preset scan

Select a band, press OK button to scan all preset stations in the memories of the current band, each preset scan for 5 seconds. To stop preset scan, press the button again.

RDS function

RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either.

AF (Alternative Frequencies) function

Press and hold SEL button, then press it repeatedly to select AF. Rotate VOLUME knob to set this function on/off. If the AF function is on, the display will show “AF”.

When the radio signal strength is poor, enabling the AF function will allow the unit to automatically search another station with the same PI (Program Identification) as the current station but with stronger signal strength, so that you do not have to retune the stations when driving between different transmitter coverage areas. When AF symbol is on, it means RDS information is received; when AF symbol is flashing, it means RDS information is not yet received. If RDS service is not available in your area, turn off the AF mode.

TA (Travel Announcement) / TP

(Travel Program Identification)

Enable or disable TA mode by pressing and

holding BAND button. Default setting is OFF.

When TA function is activated, it will search the station with TA information automatically. If there is no TA information, it will search the station with TP information automatically, if there is no TP information either, it will return to the previous station after searching.

When receiving the station with TP information but without TA information, TP icon is on and TA icon keeps blinking; when receiving the station with TP and TA information, both TP and TA icons are on.

When playing in other mode and TA information is received, it will change to the radio mode automatically. After playing over, it will return to the previous mode.

PTY (Program Type) (for FM radio)

Press and hold MEM button to open PTY program type list, and turn VOLUME knob to select a PTY type. After selecting the program type you want, press MEM button to search. Press the button again to stop the PTY search. If PTY code is different or not available, then display blinks with “PTY NONE”.

REG (Regional) function

Press and hold SEL button, then press it repeatedly to select REG, then rotate VOLUME knob to set this function on/off. Default setting is off for REG.

When REG is enabled (on), the receiver accepts regional variants of the tuned station with REG icon turned on.

When REG is disabled (off), the receiver ignores regional variants.

Mono/Stereo control (in FM radio mode)

Press and hold SEL button, then press it repeatedly until the display shows STEREO (MONO). Turn VOLUME knob to switch between ON (stereo reception) or OFF (mono

Operation

reception). Improvement of reception of distant stations can be done by selecting mono mode, which may cut down some reception noise.

Local radio station search

Press and hold SEL button, then press it repeatedly until the display shows LOCAL (DISTANT). When the LOCAL function is on, the local stations (stations with weak radio signal) can be played. When the DISTANT function is on, both local and distant stations (stations with strong radio signal) can be played.

Setting other features

Press and hold SEL button, then press it repeatedly until the display shows one of these settings: MASK DPI => EON TA => TA VOL. Rotate VOLUME knob to adjust each setting, and press OK button to confirm the adjustment.

MASK DPI: During MASK DPI mode, the unit will mask only the AF which has different PI, this is the default mode; during MASK ALL mode, the unit will mask the AF which has different PI and no RDS signal with high field strength.

EON TA: Choose EON TA DX/LO. If you want to receive information from local stations only, select EON TA LO mode. Otherwise, select EON TA DX mode.

TA VOL: Adjust the volume for TA announcement.

Disc/USB/SD/MMC operations

USB/SD/MMC notes

USB functions (flash memory type) MP3 music play.

SD/MMC card support, 2in1 (SD/MMC) support.

USB flash memory.

FAT 12/ FAT 16/ FAT 32 is possible

• FAT 12/16 (dir: 200 support, file: 500

support),

• FAT 32 (dir: 200 support, file: 500 support).

• Filename: 32 byte/ Dir name: 32 byte.

• Tag (id3tag ver2.0).

• Title/ Artist/ Album: 32 byte support. Multi card reader not support. USB 2.0

support.

USB format supports 2.0. Capacity: up

to 4 Gb.

For correct and satisfactory operation, licensed SD/MMC memory cards of famous brands should be used with this unit. Avoid using memory cards of unknown brands. Capacity: up to 4 Gb.

Loading/Ejecting a disc

Open the front panel and insert a disc into the disc slot with label side up. The disc will be automatically loaded into the unit. The first file in the root folder will be played.

Open the front panel and press EJECT button to eject the disc from the slot. If the disc is not removed from the slot within several seconds, it will be automatically loaded into the slot again. When the disc is ejected and removed, the unit will automatically switch to another mode.

Inserting the SD/MMC card/USB device

Open the front panel and insert an SD/ MMC memory card into the card slot. Open the USB slot cover on the front panel and insert a USB into the USB slot. Then the playing mode will be changed into MMC/SD or USB mode automatically. The first card/USB device track playback will start.

When SD/MMC card and USB device are both inserted, the playing mode will be changed into the mode of the device inserted later.

Stopping playback

The unit will automatically play from the first

sound track recorded on a disc/SD/ MMC /USB device. To ensure good system performance, wait until the unit finishes reading the disc /device information before proceeding. To stop playback, press MODE button and

+ 24 hidden pages