Hyundai DW12-BFM ME, DW12-BFM User Manual
Domestic Dishwasher
DW12-BFM
DW12-BFM ME
GB
Code:0120505275
Safety Is Very Important
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and
proper installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
-73/23/EEC of 19 February 1973 (Low Voltage) and subsequent modifications;
- 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility)
and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged.If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing
of household dishes and cooking utensils.
- The appliance is not intended for use by young children or
inform persons without supervision.
- Young children should be supervised to ensure that they do
not play with the appliance.
- Keep detergents out of the reach of children, who must also
be kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open as this could
over turn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting." If you cannot solve
the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.
- If the supply cord is damaged, it must be replaced by the manu
facture, its service agent of similarly qualified persons in order to
avoid a hazard.
- After installation, the power plug must be accessible.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple
sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power
supply.
To maintain the EFFICIENCY and SAFETY of this appliance,we
recommend:
- call only the Service Centers authorized by the manufacturer.
- always use original Spare Parts
Close-up View (Control Panel)
A
BC D
G
A
ON-OFF Light
B
"Eco" Button
C
Half-load Button
Low Salt Indicator Light
D
FE
E
Knob For Selecting Cycle
Handle For Opening Door
F
ON-OFF Button
G
.1.
GB
Close-up View (Interior)
Upper Rack
A
Rack Height Adjustor
B
Top Sprayer Arm
C
Lower Rack
D
Technical Characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Bottom Sprayer Arm
E
F
Washing Filter
G
Detergent and Rinse Aid Dispenser
12 standard place settings
220-240V~ 50Hz
60 cm
60 cm
85 cm
0.03-0.6 MPa
Total absorber power
GB
1950W
.2.
Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a
salt specifically designed to eliminate lime and minerals from
the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used. This is
intended to optimise and customise the level of salt consumption so that it remains at a minimum.
To adjust salt consumption, proceed as follows:
To prevent the formation of rust, load the salt just before
beginning a wash cycle.
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure).
- If necessary, rotate the ring in the anticlockwise direction from
the "-" setting towards the "+" sign, based on the hardness of
the water being used.
It is recommended that adjustments be made in accordance with
the following scheme:
Water Hardness
Level
1
2
3
Clarke
degrees
0 14
ºdH
mmol/l
Selector
position
Salt
consumption
(Grams/cycle)
Autonomy
(cycles/2kg)
.3.
4
GB
Loading...