Hydra-Tech S6TCAL User Manual
6” HYDRAULIC SUBMERSIBLE
TRASH PUMP
MODELS:
S6TC (Ductile Iron Body)
S6TCAL (Aluminum Body
6” (150 mm) Discharge
The S6TC is a 6" discharge trash
pump designed specifically to easily
pass through a 22" manhole. The
S6TC uses a high efficiency two
channel impeller with adjustable
wear surface. It is available with a
durable ductile iron or lightweight
aluminum casing.
S6TC
FEATURES
High Efficiency Closed Channel Impeller
•
(will pass 3" semi-solids)
Compact Design allows this pump to fit
•
through a 21” opening
Variable Speed hydraulic drive provides a
•
wide range of performance
Oil Lubricated Seals (can run dry)
•
Adjustable Wear Ring
•
Can be bolted directly into a pipeline or
•
used as a booster pump
Safe Hydraulic Drive can be used where
•
electric power is hazardous or impractical
Operates with our HT35 to HT60 power
•
units or other hydraulic power sources
capable of flows to 28 GPM
D0413
WEIGHT: S6TC.......................................... 270 lbs. (122 kg)
S6TCAL....................................... 175 lbs. (80 kg)
HEIGHT:............................................................. 34" (86 cm)
WIDTH (@ widest point):............................. 20-3/4" (53 cm)
DISCHARGE:....................................................... 6" NPT(F)
INLET FLANGE:............................................. 6" 125# ANSI
SOLIDS HANDLING:.......................................... 3" (75 mm)
HOSE PORTS:................................................ 1" (-16) SAE
PUMP BODY: S6TC........................................... Ductile Iron
S6TCAL......................................... Aluminum
IMPELLER:........................................................ Ductile Iron
WEAR RING...................................................... Ductile Iron
SHAFT:........................................... 17-4 PH Stainless Steel
SHAFT SEAL:.................................. Carbon / Ceramic (Std)
Silicon Carbide (Opt)
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:............................... Max. 28 GPM (106 LPM)
OPERATING PRESSURE:............. Max 2900 PSI (197 Bar)
POWER SOURCE:...... Any Open Center Hydraulic System
S6TCAL
SPECIFICATIONS
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S6TC Overall Dimensions
S6TC Typical Performance
0
150
135
120
105
90
75
60
45
30
15
15
30
45
U.S.G.P.M.
Liters/Minute
Feet
Meters
1200
CAPACITY
TOTAL HEAD
2000
200
400
600
800
1000
1200
1400
1600
1800
7200
6000
4800
3600
2400
A
B
HYDRAULIC INPUT:
A) 15 GPM @ 550 - 1000 PSI
B) 21 GPM @ 1000 - 1850 PSI
C)* 25 -28 GPM @ 1900 - 2900 PSI
* Typical Performance with
HT60 Power Unit
C
34"
(86 cm)
6" NPT (F)
20 3/4"
14 1/2"
(53 cm)
(37 cm)
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...