Hydra-Tech S6200 User Manual
8” HYDRAULIC SUBMERSIBLE
HIGH PERFORMANCE,
SOLIDS HANDLING PUMP
MODEL S6200
8” (200 mm) Discharge
The S6200 is a Highly Efficient Solids
Handling Effluent Pump for use on jobs
such as Waste Lagoons, Sewer By-Pass,
Barge Transfer, Municipal Lift Stations
and Tank Pumping.
FEATURES
Balanced High Efficiency Two Vane
•
Closed Channel Impeller
Will pass 4" (100 mm) semi-solids
•
Variable Speed hydraulic drive provides
•
a wide range of performance
Oil Lubricated Seals (can run dry)
•
High Efficiency Balanced Vane
•
hydraulic motor
Can be bolted directly into a pipeline or
•
used as a booster pump
Safe Hydraulic Drive can be used where
•
electric power is hazardous or
impractical
Operates with our HT100 to HT200
•
power units or other hydraulic power
sources capable of flows of 50 - 90 GPM
B0109
SPECIFICATIONS
WEIGHT:..................................................... 715 lbs. (324 kg)
HEIGHT:............................................................ 41" (104 cm)
WIDTH (@ widest point):................................. 28.5" (72 cm)
DISCHARGE:....................................... 8", 125# ASA Flange
INLET:.................................................. 8", 125# ASA Flange
SOLIDS HANDLING:........................................ 4" (100 mm)
HOSE PORTS:......1-1/4" Code 61 Flange or 1-1/2" NPT (F)
PUMP BODY:...................................................... Ductile Iron
IMPELLER:.......................................................... Ductile Iron
WEAR RING........................................................ Ductile Iron
SHAFT:.............................................17-4 PH Stainless Steel
SHAFT SEAL:............................................... Silicon Carbide
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:................................ Max 90 GPM (340 LPM)
OPERATING PRESSURE:............. Max 2500 PSI (170 Bar)
POWER SOURCE:....... Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S6200 Overall Dimensions
23"
7"
(58cm)
(18cm)
(72cm)
8", 125# ASA Flanges
28.5"
24"
41"
(61cm)
(44cm)
(104 cm)
17.2"
CAPACITY
0
220
200
180
160
140
120
100
80
60
40
202040
60
U.S.G.P.M.
Cu. Mtr./Hr.
Feet
Meters
TOTAL HEAD
ABC
5000
4500
4000
3500
3000
2500
2000
1500
1000
500
1000
600
800
400
200
HYDRAULIC INPUT:
A) 53 GPM
!!!!!Typical Performance with
!!!! HT100 Power Unit
B) 70 GPM
!!!Typical Performance with
!!!!HT150 Power Unit
C) 90 GPM
!!!!Typical Performance with
!!!!!HT200 Power Unit
S6200 Typical Performance
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...