Hydra-Tech S6150 User Manual
6” HYDRAULIC SUBMERSIBLE
HIGH PERFORMANCE,
SOLIDS HANDLING PUMP
MODEL S6150
6” (150 mm) Discharge
The S6150 is a High Performance
Solids Handling Pump for use on jobs
where higher heads or long discharge
runs are encountered such as Lift
Stations or Ship Offloading.
FEATURES
Balanced High Efficiency Two Vane
•
Closed Channel Impeller
Will pass 3" (75 mm) semi-solids
•
Variable Speed hydraulic drive provides
•
a wide range of performance
Oil Lubricated Seals (can run dry)
•
High Efficiency Balanced Vane
•
hydraulic motor
Can be bolted directly into a pipeline or
•
used as a booster pump
Safe Hydraulic Drive can be used where
•
electric power is hazardous or
impractical
Operates with our HT100 to HT200
•
power units or other hydraulic power
sources capable of flows of 50 - 90 GPM
B0109
SPECIFICATIONS
WEIGHT:..................................................... 650 lbs. (294 kg)
HEIGHT:.............................................................. 38" (79 cm)
WIDTH (@ widest point):.................................... 26" (66 cm)
DISCHARGE:....................................... 6", 125# ASA Flange
INLET:................................................... 6", 125# ASA Flange
SOLIDS HANDLING:.......................................... 3" (75 mm)
HOSE PORTS:......1-1/4" Code 61 Flange or 1-1/2" NPT (F)
PUMP BODY:...................................................... Ductile Iron
IMPELLER:.......................................................... Ductile Iron
WEAR RING........................................................ Ductile Iron
SHAFT:.............................................17-4 PH Stainless Steel
SHAFT SEAL:............................................... Silicon Carbide
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:................................. Max 90 GPM (340 LPM)
OPERATING PRESSURE:............. Max 2500 PSI (170 Bar)
POWER SOURCE:....... Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S6150 Overall Dimensions
21"
6"
(53cm)
(15cm)
(66cm)
6", 125# ASA Flanges
26"
24"
38"
(61cm)
(40cm)
(97cm)
15.6"
0
330
300
270
240
210
180
150
120
90
60
30
30
60
90
U.S.G.P.M.
Cu.Mtr./Hr.
Feet
Meters
100
CAPACITY
TOTAL HEAD
A
B
C
2700
2400
2100
1800
1200
1500
900
600
300
600
500
400
300
200
HYDRAULIC INPUT:
A) 53 GPM
!!!!!Typical Performance with
!!!! HT100 Power Unit
B) 70 GPM
!!!Typical Performance with
!!!!HT150 Power Unit
C) 90 GPM
!!!!Typical Performance with
!!!!!HT200 Power Unit
S6150 Typical Performance
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...