Hydra-Tech S4VHLDI User Manual
4” HYDRAULIC SUBMERSIBLE
SLUDGE / SLURRY PUMP
MODEL S4VHL (Aluminum Body)
MODEL S4VHLDI (Ductile Iron Body)
4” (100 mm) Discharge
The S4VHL is designed to handle wastewater
and sewage and will fit through a 20" diameter
manhole . Primary uses for this pump are:
Sewer by-pass into force mains and general
transfer of solids laden fluids. This versatile
pump is offered in aluminum or ductile iron
construction.
FEATURES
Small Overall Size allows pump to fit
•
through a 20" diameter opening
Oil Lubricated Seals (can run dry)
•
Variable Speed hydraulic drive
•
Fully Recessed Vortex Impeller
•
(will pass 3" semi-solids)
Can be bolted directly into a pipeline or
•
fitted with a suction hose for underwater
dredging
Safe Hydraulic Drive can be used where
•
electric power is hazardous or impractical
Dependable gear type hydraulic motor
•
Operates with our HT25 to HT60 power
•
units or other hydraulic power sources
capable of flows of 14 - 26 GPM
C0413
SPECIFICATIONS
WEIGHT: (Aluminum)................................... 160 lbs. (72 kg)
(Ductile Iron)............................. 265 lbs. (120 kg)
HEIGHT:............................................................. 33" (84 cm)
WIDTH(@ widest point):............................. 19 3/4" (50 cm)
DISCHARGE:...................................................... 4", NPT(F)
INLET FLANGE:............................................ 4", 125# ASA
SOLIDS HANDLING:.............................................. 3" (8 cm)
HOSE PORTS:................................................ 1" (-16) SAE
PUMP BODY: (S4VHL)................. Heat Treated Aluminum
(S4VHLDI)................................. Ductile Iron
IMPELLER:................................................... Stainless Steel
WEAR RING and WEAR PLATE.................. Stainless Steel
SHAFT:......................................................... Stainless Steel
SHAFT SEAL:.................................... Carbon/Ceramic (Std)
Silicon Carbide (Optional)
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:.................................. Max 26 GPM (98 LPM)
OPERATING PRESSURE:............ Max 3000 PSI (204 Bar)
POWER SOURCE:....... Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S4VHL Overall Dimensions
S4VHL Typical Performance
19 3/4"
39"
33"
(99 cm)
(84 cm)
(50 cm)
15"
(38 cm)
0
220
200
180
160
140
120
100
80
60
40
20
20
40
60
U.S.G.P.M.
Liters/Minute
Feet
Meters
600
CAPACITY
TOTAL HEAD
70
240
30
50
10
100
200
300
400
500
600
700
800
900
1000
1200
1800
2400
3000
3600
HYDRAULIC INPUT:
A) *14 GPM @ 800 - 2600 PSI
B) 16 -18 GPM @ 1300 - 2900 PSI
C) 18 -20 GPM @ 1500 - 2900 PSI
D) **15 -25 GPM @ 2500 - 2900 PSI
A
B
D
C
* Typical perf. with HT25 Power Unit
** Typical perf. with HT60 Power Unit
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...