Hydra-Tech S4TLPAL User Manual
4” HYDRAULIC SUBMERSIBLE
TRASH PUMP
MODELS
S4TLP (Ductile Iron Body)
S4TLPAL (Aluminum Body)
4” (100 mm) Discharge
The S4TLP trash pump is designed to
fit into tighter spaces and can be used
for tank truck mounting for direct
loading/offloading using on-board
hydraulics. It is well suited for operating
with smaller hydraulic tool power units.
Your preference of durable ductile iron
or lightweight aluminum body makes
this pump an all around choice.
FEATURES
2-Vane Channel Impeller
•
(will pass 3" (75 mm) semi-solids)
Variable Speed hydraulic drive
•
Wide Range of performance
•
Can be bolted directly to a tank or truck.
•
Safe Hydraulic Drive can be used where
•
electric power is hazardous or impractical
Dependable gear type hydraulic motor
•
Operates with our HT10 to HT20 power
•
units or other hydraulic power sources
capable of flows of 5-10 GPM
A1110
SPECIFICATIONS
WEIGHT: S4TLP................................ 107 lbs. (48 kg)
S4TLPAL ............................ 68 lbs. (31 kg)
HEIGHT:............................................. 13-3/4” (40 cm)
WIDTH (@ widest point):.................... 19-1/2" (50 cm)
DISCHARGE:.............................................. 4" NPT(F)
INLET FLANGE:................................... 4", 125# ASA
SOLIDS HANDLING:................................ 3" (75 mm)
HOSE PORTS:.................... 7/8-14 UNF (-10) SAE(F)
PUMP BODY: S4TLP................................ Ductile Iron
S4TLPAL............................. Aluminum
IMPELLER:............................................... Ductile Iron
SHAFT SEAL:...................... Grease Lube Double Lip
ELASTOMERS:..................................... Buna N (Std)
HYDRAULIC OIL:..... 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:....................... Max. 10 GPM (38 LPM)
OPERATING PRESSURE:. Max. 2800 PSI (190 Bar)
POWER SOURCE:.. Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S4TLP Overall Dimensions
0 100 200 300 400 500 600 700 800 900
80
70
60
50
40
30
20
10
10
20
U.S.G.P.M.
Liters/Minute
Feet
Me
t
ers
600 1200 1800 2400 3000 3400
CAPACITY
TOTAL HEAD
90
A
B
C
D
E
F
Hydraulic Input
(A) 5 GPM @ 100-1000 PSI
(B) 6 GPM @ 200- 1050 PSI
(C) 7 GPM @ 400-1600 PSI
(D) 8 GPM @ 600-2100 PSI
(E) 9 GPM @ 900-2800 PS I
(F) 10 GPM @ 1000-2800 PSI
25
5
15
4" NPT (F)
15-3/4" (40 cm)
12" (30.5 cm)
Motor Ports
7/8 -14 UNF-2B
(SAE -10)
19 1/2" (50 cm)
1
5
"
(
3
8
c
m
)
S4TLP Typical Performance
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...