Hydra-Tech S3VHLDI User Manual
3” HYDRAULIC SUBMERSIBLE
SLUDGE / SLURRY PUMP
MODEL S3VHL (Aluminum Body)
MODEL S3VHLDI (Ductile Iron Body)
3” (75 mm) Discharge
The S3VHL is designed to pump sludge,
slurries and liquids with stringy solids.
Uses for this pump include liquid manure
pumping, water treatment slurries and
clarifier tanks. This versatile pump is
offered in aluminum or ductile iron
construction.
FEATURES
Small Overall Size allows pump to fit
•
through a 20" diameter opening
Oil Lubricated Seals (can run dry)
•
Variable Speed hydraulic drive
•
Fully Recessed Vortex Impeller
•
(will pass 3" semi-solids)
Can be bolted directly into a pipeline or
•
fitted with a suction hose for underwater
dredging
Safe Hydraulic Drive can be used where
•
electric power is hazardous or impractical
Dependable gear type hydraulic motor
•
Operates with our HT15 to HT35 power
•
units or other hydraulic power sources
capable of flows of 10 - 18 GPM
D0413
SPECIFICATIONS
WEIGHT: (Aluminum)................................... 176 lbs. (80 kg)
(Ductile Iron)............................. 289 lbs. (131 kg)
HEIGHT:............................................................. 33" (84 cm)
WIDTH(@ widest point):............................. 19 3/4" (50 cm)
DISCHARGE:...................................................... 3", NPT(F)
INLET FLANGE:.................Drilled for 3" and 4", 125# ASA
SOLIDS HANDLING:.............................................. 3" (8 cm)
HOSE PORTS:................................................ 1" (-16) SAE
PUMP BODY: (S3VHL)................. Heat Treated Aluminum
(S3VHLDI)................................. Ductile Iron
IMPELLER:................................................... Stainless Steel
WEAR RING and WEAR PLATE.................. Stainless Steel
SHAFT:......................................................... Stainless Steel
SHAFT SEAL:.................................... Carbon/Ceramic (Std)
Silicon Carbide (Optional)
ELASTOMERS:................................................ Buna N (Std)
HYDRAULIC OIL:................ 214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:.................................. Max 18 GPM (68 LPM)
OPERATING PRESSURE:............ Max 3000 PSI (204 Bar)
POWER SOURCE:....... Any Open Center Hydraulic System
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S3VHL Overall Dimensions
S3VHL Typical Performance
19 3/4"
39"
33"
(99 cm)
(84 cm)
(50 cm)
15"
(38 cm)
0
200
180
160
140
120
100
80
60
40
20
20
40
60
U.S.G.P.M.
Liters/Minute
Feet
Meters
600
CAPACITY
TOTAL HEAD
30
50
10
100
200
300
400
500
600
700
800
900
1000
1200
1800
2400
3000
3600
HYDRAULIC INPUT:
A) 10 GPM @ 950 - 2800 PSI
B) *10 - 15 GPM @ 1800 - 2600 PSI
C) **11 - 18 GPM @ 2500 - 2900 PSI
A
B
C
* Typical perf. with HT25 Power Unit
** Maximum performance
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...