Hydra-Tech S3CSL User Manual
3” HYDRAULIC SUBMERSIBLE
SAND / SLURRY PUMP with AGITATOR
MODEL S3CSL
3” (75 mm) Discharge
The S3CSL pump is designed to use in
applications requiring settled solids to be put
into suspension and pumped with the discharge
water. Primary applications include de-silting
ponds, lakes and streams. Other jobs may
include filling sand bags to prevent beach
erosion, tank and digester cleaning or pumping
residue from rail tank cars or barges.
FEATURES
Hardened Alloy Wear Parts
•
Built-in Agitator for stirring up solids
•
Oil Lubricated Seals (can run dry)
•
Variable Speed hydraulic drive
•
Small Size allows pump to fit through a
•
17 inch opening
Safe Hydraulic Drive can be used where
•
electric power is hazardous or impractical
Dependable gear type hydraulic motor
•
Operates with our HT10 to HT20 power
•
units or other hydraulic power sources
capable of flows to 10 GPM
B0109
SPECIFICATIONS
WEIGHT:..........................................231 lbs. (105 kg)
HEIGHT:..............................................30 1/4" (77 cm)
WIDTH (@ widest point):....................16 1/4" (41 cm)
DISCHARGE:..................................................3" NPT
SOLIDS HANDLING:..........................1 1/2" (38 mm)
HOSE PORTS:..........................1/2" and 3/4" NPT (F)
VOLUTE*:................................ Hardened Ductile Iron
IMPELLER:................................... High Chrome Alloy
WEAR PLATE............................... High Chrome Alloy
AGITATOR:...................................High Chrome Alloy
SHAFT:.........................................304 Stainless Steel
SHAFT SEALS: (upper)....................Carbon/Ceramic
(Lower)......................Silicon Carbide
HYDRAULIC OIL:.......214-320 s.s.u. @ 100°F (64°C)
INPUT FLOW:.........................Max 10 GPM (38 LPM)
OPERATING PRESSURE:....Max 3000 PSI (204 Bar)
POWER SOURCE:.. Any Open Center Hydraulic System
* Optional NI-Hard volute available for highly abrasive applications
Specifications are subject to change without notice
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Model S3CSL Overall Dimensions
30 1/4"
16 1/4"
(41cm)
(77cm)
14"
16 1/4"
(36cm)
(41cm)
HYDRAULIC INPUT:
(A) 5 GPM @ 700 - 1000 PSI
(B)* 7 GPM @ 1000 - 1600 PSI
(C) 9 GPM @ 1500 - 2400 PSI
(D) 9.7 -10 GPM @ 1850 - 2800 PSI
* Typical performance using HT11D
or HT13G Power Unit
0 50 100 150 200 250 300 350 400 450 500
100
90
80
706050
40
30
20
10
10
20
30
U.S.G.P.M.
Liters/Minute
Feet
Meters
300 600 900 1200 1500 1800
A
B
CAPACITY
TOTAL HEAD
C
D
S3CSL Typical Performance
Curves are based on pumping water at 60°F. For performance curves other than shown above, consult factory.
167 Stock Street, Nesquehoning, PA 18240 Phone: 570-645-3779 Fax: 570-645-4061
Website
: www.hydra-tech.com E-Mail: htpump@hydra-tech.com
Loading...