Hustler Turf 3500, 3700 User Manual

Hustler 3500/3700

60”/72” Out Front Deck

Owner’s Manual

109631_0908

•••••

P.O. Box 7000

•••

Hesston, Kansas

•

67062-2097

109631_0908

GENERAL INFORMATION

This manual applies to the following Hustler equipment lines:

Hustler Front Mount Deck 60”
Hustler Front Mount Deck 72”

To the new o w n e r

The purpose of this manual is to assist owners and operators in maintain­ing and operating the Hustler Front Mount Decks. Please read it carefully;
information and instructions furnished can help you achieve years of de pen d ­able performance.

It is the owner’s responsibility to make certain that the operators and
mechanics read and understand this manual and all decals before operating
this machine. It is also the owner’s responsibility to make certain that the
operators and mechanics are qualified and physically able individuals, prop­erly trained in the operation of this equipment. All operator and mechanics
must become familiar with the safe operation of the equipment, operator con­trols and safety signs.

IMPORTANT: For more detailed maintenance and adjustment informa­tion refer to the proper parts manual for your machine.

The owner/user can prevent and is responsible for accidents or injuries
occurring to themselves, other people or property.

Using this manual

General operation, adjustment and maintenance guidance is outlined for
both the experienced and novice Hustler user . Operating conditions vary con­siderably and cannot all be addressed individually. Through experience,
however, operators should find no difficulty in developing good operating
skills suitable to most conditions.

Directions used in this manual, for example RIGHT or LEFT, refer to
directions when seated on tractor facing forward, unless otherwise stated.

Photographs and illustrations used were current at the time of printing,
but subsequent production changes may cause you r machine to vary slightly
in detail. Hustler Turf Equipment reserves the right to redesign and change
the machine as deemed necessary, without notification. If a change has been
made to your machine which is not reflected in this owner’s manual, or the
parts manual, see your Hustler dealer for current information and parts.

Warranty registration

The completed Warranty Registration and Delivery form must be sent to
Hustler Turf Equipment within ten (10) days of delivery to validate your war­ranty protection. As the new equipment owner, you are expected to see that
the form is completed and forwarded to Hustler Turf Equipment at time of
delivery. The warranty registration form can also be accomplished electroni­cally by the Hustler Dealer to validate the warranty.

This form must be on file for validation before any warranty claim appli­cations can be processed by Hustler Turf Equipment.

Be sure to register the tractor plus each attachment that displays a model
and serial identification number plate with Hustler Turf Equipment.

IMPORTANT: Any unauthorized modification, alteration, or use of
non-approved attachments voids the warranty and releases Hustler Turf
Equipment from any liability arising from subsequent use of this equipment.

Model and serial number

Model and serial numbers are found on the serial identification plate,
located on the left rear top of the deck.

These numbers are required on the Warranty Registration form. They
will also assure you of the correct service parts when replacement becomes
necessary.

Parts and service

Use original Hustler replacement parts only. These parts are available
through your local Hustler dealer. To obtain prompt, efficient service, always
provide the following information when ordering parts:

1. Correct part description

2. Correct model number.

3. Correct serial number.

All warranty repair and service must be handled through an authorized
Hustler dealer. Arrangem ents should be made th rough y our local service cen­ter.

109631_0908 1-1

1-2 109631_0908

HUSTLER FRONT MOUNT DECKS

TWO YEAR LIMITED WARRANTY FOR DECK

(THREE YEAR LIMITED WARRANTY ON DECK

SPINDLE BEARING & DECK GAUGE FORK BEARING)

WHAT IS COVERED BY THIS WARRANTY

Hustler Turf Equipment, makes the following warranty to the original pur­chaser only:

a. First and Second Year: Hustler Turf Equipment Tractors and Power

Units are warranted for two (2) years from date of deliver y on all
materials and workmanship.
If the Purchaser discovers within this warranty period a defect in
materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or an authorized
dealer, in writing of the defect. In no event shall such notification
be received by Hustler Turf Equipment, or an authorized dealer later
than twenty-five (25) months from date of delivery.

● Within a reasonable time after such notification, Hustler Turf
Equipment, will correct any defect in material or workmanship on
the Hustler Turf Equipment, by repairing or replacing part(s) with
either new or used replacement parts.

● Such repair, including parts and labor shall be at the expense of
Hustler Turf Equipment, and,

b. Third Year: At the conclusion of the two year limited warranty

described in paragraph (a) above, there shall be an additional one year
limited warranty on deck gauge fork bearings and deck spindle bear­ings only, no labor.
If the Purchaser discovers within this warranty period a defect in
either of these bearings:

● He must promptly notify Hustler Turf Equipment, or an authorized
dealer, in writing of the defect. In no event shall such notification
be received by Hustler Turf Equipment, or an authorized dealer later
than thirty-seven (37) months from date of delivery.

● Within a reasonable time after such notification, Hustler Turf
Equipment, will provide new replacement bearing to install on the
Hustler Turf Equipment.

● The installation of the deck gauge fork bearing and deck spindle
bearing shall be at the expense of the owner, and,

c. Rental Units (9 0 days): Within 90 days of date of delivery Hustler

Turf Equipment, provides a limited warranty on all materials and
workmanship for units used for rental purposes.
If the Purchaser discovers within this warranty period a defect in
materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or an authorized
dealer, in writing of the defect. In no event shall such notification
be received by Hustler Turf Equipment, or an authorized dealer later
than 120 days from date of delivery.

● Within a reasonable time after such notification, Hustler Turf
Equipment, will correct any defect in material or workmanship on
the Hustler Turf Equipment, by repairing or replacing part(s) with
either new or used replacement parts.

● Such repair, including parts and labor shall be at the expense of
Hustler Turf Equipment, and,

WHO MUST PERFORM THE WARRANTY SERVICE

All warranty service will be performed by dealers authorized by Hustler Turf
Equipment. Service calls and/or transportation expense of the product to
and from the authorized dealer, for warranty work, will be paid by the owner
of the product. For warranty service you can contact an authorized dealer or
write Hustler Turf Equipment, 200 South Ridge Road, Hesston, Kansas
67062, or call 1-620-327-4911.

WHAT IS NOT COVERED BY THIS WARRANTY

Hustler Turf Equipment, does not warranty:

● Some product, components or parts not manufactured by Hustler
Turf Equipment

● Repairs made by unauthorized persons

● Damage caused by use of the Hustler Turf Equipment for purposes

other than those for which it was designed

● Damages caused by disasters such as fire, flood, wind, and lighten­ing

● Damages caused by foam filled or solid filled tires.

● Damages caused by neglect, abuse, abnormal use, improper or

unreasonable use, accident, negligence or misuse

● Repairs or replacement resulting from the use of unauthorized parts,
accessories or attachments

● Repairs or replacement as the result if any alterations or modifica­tions, in the determination of Hustler Turf Equipment, which
adversely affects the operation, performance or durability of the
equipment.

● Hustler Turf Equipment which has the serial number removed or
made illegible

● Depreciation or damage caused by normal wear, lack of reasonable
and proper maintenance, failure to follow the product’s owner’s
manual operating, maintenance and adjustment instructions or other
operational instructions provided by Hustler Turf Equipment.

● Normal maintenance parts and service including, but not limited to,
lubricants, belts, blades, blade sharpening, bearings

DISCLAIMER OF WARRANTY

The foregoing warranties are in lieu of all other warranties, expressed or
implied, including but not limited to the implied warranties of merchant­ability and fitness for a particular purpose. However, if the Hustler Turf
Equipment is purchased as a consumer product, any implied warranty of
merchantability or fitness for a particular purpose is limited to the dura­tion of this limited warranty. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not
apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

LIMITATION OF REMEDIES

In no case shall Hustler Turf Equipment, be liable for any special, incidental,
or consequential damages based upon breach of warranty, breach of contract,
negligence, strict liability in tort, or any other legal theory.
Such damages include, but are not limited to:

● Loss of profits

● Loss of savings or revenue

● Loss of use of Hustler Turf Equipment or any associated equipment

● Cost of capital

● Cost of any substitute equipment, facilities, services or downtime

● The claims of third parties including customers, and injury to prop-

erty

Some states do not allow the exclusion or limitation of incidental or conse­quential damages, so the above limitation or exclusion may not apply to you.

TIME LIMIT

Any action for breach of warranty must be commenced within twenty-five
(25) months following delivery of the goods in a non-rental application. Any
action for breach of warranty must be commenced within 120 days following
delivery of the goods in a rental application.

NO OTHER WARRANTIES

Unless modified in writing, signed by both parties, and approved by the Pres­ident of Hustler Turf Equipment, this agreement is understood to be the com­plete and exclusive agreement between the parties, superseding all prior
agreements, oral or written, and all other communications between the parties
relating to the subject matter of this agreement. No employee of Hustler Turf
Equipment, or any other party is authorized to make any warranty in addition
to those made in this agreement.

109631_0908 1-3

ALLOCATION OF RISKS

This agreement allocates the risks of product failure between Hustler Turf
Equipment, and the purchaser. This allocation is recognized by both parties
and is reflected in the price of the goods.

OWNER'S RESPONSIBILITY

You must maintain your Hustler Turf Equipment product following the main­tenance procedures described in your owner's manual. Such routine mainte­nance, whether performed by a dealer or by you, is at your expense.

This machine like any other powered equipment is potentially dangerous
unless properly operated. Any operator must be cautious and keep safety in

mind at all times. Any operator, prior to using the Hustler Turf Equipment,
should thoroughly familiarize himself with the owner's manual regarding
operation and safety of the machine, as well as all safety warnings on the
machine itself.

WARRANTY REGISTRATION

1. Dealers must register the unit on-line at www.Hustler dealer.com or by

filling out the Warranty registration fo rm, provided in the owner’s packet.
If using the Warranty registration form it MUST be completed and signed
by the authorized dealer and original purchaser.

2. For validation, the completed Warranty registration form MUST be for-

warded to Hustler Turf Equipment, within ten (10) days following date of
purchase.

3. The date of purchase constitutes delivery.

1-4 109631_0908

SAFETY PRECAUTIONS

This safety alert symbol is used to call attention to a message intended to
provide a reasonable degree of PERSONAL SAFETY for operators and other
persons during the normal operation and servicing of this equipment. Obey
all safety messages that follow this symbol to avoid possible injury or death.

DANGER – denotes immediate hazards which WILL result in severe per­sonal injury or death.

WARNING – denotes a hazard or unsafe practice which COULD result in
severe personal injury or death.

This manual uses two other words to highlight information. IMPORTANT
calls attention to special mechanical information and NOTE: emphasizes
general information worthy of special attention.

All operators and mechanics should read this manual, and be instructed
about safe operating and maintenance procedures. If the operators or
mechanics cannot read and understand English, it is the owner’s responsibil­ity to explain this material to them.

Incorrect usage of this machine may result in severe injury. Personnel
operating and maintaining it should be trained in the proper use and
should read the manuals completely and thoroughly before attempting to
set-up, operate, adjust, or service this machine.

It is the owner’s responsibility to make certain that the operators and

mechanics read and understand this manual and all decals before operating
this machine. It is also the owner’s responsibility to make certain that the
operators and mechanics are qualified and physically able individuals, prop­erly trained in the operation of this equipment. All operator and mechanics
must become familiar with the safe operation of the equipment, operator con­trols and safety signs.

Never let children or untrained people operate or service the equipment.

Local regulations may restrict the age of the operator.

IMPORTANT: For more detailed maintenance and adjustment informa-

tion refer to the proper parts manual for your machine.

The owner/user can prevent and is responsible for accidents or injuries

occurring to themselves, other people or property.

The owner should also ensure that the operator/mechanic know that they

are responsible for their own safety as well as the safety of other persons
within the vicinity. Remember, the operator is responsible for accidents or
hazards occurring to other people or their property.

109631_0708 2-1

Safety and Instruction Decals

601624

V Specific safety warning decals are located on the equipment near the immediate areas of potential hazards. These decals should not be removed or oblit-

erated. Replace them if they become non-readable.

The following illustrations show the various decals that are located on the machine. A brief explanation, for those requiring one, is shown to help the operator
understand the meanings of these decals.

WAR NI NG :
Read Owner’s Manual before attempting
to operate or service this machine.

Wear ear protection, eye protection and safety shoes when
operating this equipment.

WARNING: Rotating driveshaft!

Part Number

601623

Part Number

601625

601623

• Keep hands, feet and clothing clear of
this area.

• Keep a safe distance from the
machine.

• Keep shields or covers in place while
machine is in operation.

Part Number

601624

WARNING: Thrown
objects

• Never operate the mower deck with side
deflector damaged, altered, removed or
in raised position, except when the
entire grass catcher attachment or
mulching system is being used.

Part Number

601603

WARNING:
Thrown objects

• Always maintain a
safe distance from
people and pets
when mowing.

• Always stop
machine if some­one enters the
area.

DANGER
Rotating blades, pulleys & belts

Part Number

601603

• Keep hands, feet and clothing away.

• Keep shields or covers in place while
machine is in operation.

2-2 109631_0708

OPERATION

1. Gauge wheel assemblies 5. Deck carrier arm

2. Discharge chute 6. PTO shaft

3. Gearbox 7. Rear height adjustment

4. Front height adjustment 8. Anti-scalp wheels

9. Locking pin





























Safe Operating Practices

This product is capable of amputating hands and feet and throwing
objects. Always follow all safety instructions to avoid serious injury or
death.

Operation

V Always keep safety shields and covers in place, except for servicing.

V Follow daily and weekly checklists, making sure hoses are tightly

secured and bolts are tightened.

V Always inspect machine for damage after striking a foreign object. If

damage is found, repair machine immediately. Be sure to stop on
level ground, place park brake lever in the brake engaged position,
place the PTO lever in the “OFF” position, lower attachment, remove
ignition switch key before leaving operator’s seat to inspect damage.

V Never turn the PTO switch on unless the PTO shaft is securely con-

nected to a power driven attachment.

V Never operate a poorly maintained machine.

V Always operate machine in daylight or with adequate workinglights.

V Never put hands or feet under any part of the machine while it is run-

ning.

V Never direct discharged material toward anyone. Avoid discharging

material against a wall or obstruction. Material may ricochet back
toward the operator. Always disengage the blades and wait for them
to stop before crossing gravel drives, walks or roads.

V Always be alert for hazards such as rocks, metal objects and other

debris which may be thrown or en tangled by mower blades. Watch
out for holes or deep depressions.

V Inspect area to be mowed for hazards such as rocks, metal objects and

other debris which may be thrown o r entangled by mower blades.
Remove these objects before mowing.

V Always keep clear of the mower blades and attachments during their

operation.

V Always maintain a safe distance from people and pets when mowing.

Always stop machine if someone enters the area.

V Never attempt high speed maneuvering in crowded or congested areas
V Turn off blades when not mowing.
V Never raise the mower deck with the blades engaged to avoid small

obstacles, drive over curbs and so forth. Disengage the pto clutch
before raising the deck.

V Stop the engine before removing the grass catcher or unclogging the

discharge chute. Never clear the discharge chute with the engine run­ning. Turn off the engine and be sure the blades have stopped before
cleaning. Use a stick to clear a plugged discharge area. Never use

your hand!

V Follow the manufacturer’s recommendation for wheel weights or

counterweights.

V Never attempt to back machine onto transport trailer with mower

deck or attachment in the raised position.

V Clean flammable material from machine. Prevent fires by keeping

the mower deck clean of accumulated trash, grass clippings, and other
debris.

109631_0908 3-1

Fig. 3-1

Attaching mower deck to tractor

HST foot pedals

Brake pedal

Forward

travel
pedal

Reverse

travel
pedal

Engine shaft

PTO shaft

Input shaft

Woodruff key

Clevis pin

Tool bar

Hair pin

Carrier arm

Universal joint

5/16” cap screw

Flat washer

5-16” nut

To attach the Front Mount Mower Deck to a tractor, follow these recom-

mended steps:

1. Insert the woodruff key into the keyway on the gearbox’s input shaft.

Align the woodruff key with keyway on universal joint of PTO shaft.
Coat the gearbox input shaft with NEVER-SEEZ compound. Slide uni­versal joint onto gearbox shaft. Secure PTO shaft to gearbox shaft with
5/16” cap screw, flat washer , and 5/16” nut provided. Fig. 3-2 and 3-3

2. Lower tractor tool bar.

3. Block rear of mower deck up so that the deck carrier arms are at the

same height as the tractor tool bar.

4. Drive the tractor ahead slowly and insert mower deck carrier arms into

the tractor tool bar. Stop tractor engine, engage park brake and remove
key from the igniton switch. Fig. 3-4

WARNING: Stop engine. Make sure PTO switch is off.
Engage park brake and remove ignition key before getting off
machine.

5. By moving the mower deck, align the holes in deck carrier arms and

tractor tool bar.

6. Insert tractor clevis pins through holes in tool bar and carrier arms and

lock clevis pins in place using hair pins provided. Fig. 3-4

7. Attach the PTO shaft to the engine shaft. Fig. 3-5

NOTE: Never attach the PTO shaft to the engine shaft without it being
attached to the mower deck gearbox.

8. The mower deck is now ready for the deck leveling procedure. To

remove deck from tractor, reverse above procedure.

Fig. 3-4

Leveling mower deck

affect levelness of cut in mowing position. Mower deck will mow (cut) level
if it is level when set on level surface.

NOTE: Levelness of mower deck when lifted from surface does not

Fig. 3-2

Fig. 3-3

Fig. 3-5

Refer to tractor owner’s manual for correct tractor tire pressure. To level

mower deck use the following procedure:

1. Park the unit on a flat surface and set the park brake. Shut off tractor

engine and remove key from the igniton switch.

WARNING: Stop engine. Remove ignition key before getting
off machine.

2. Check the deck’s tire pressure and adjust it accordingly. Tire pressure

should be 8-12 psi (55-83 KPa).

3. Set the 3500/3700 tractor’s Tool Bar Lift Control Lever in the fully for-

ward position. (Refer to tractor’s owner’s manual for complete informa­tion.)

4. Rotate the 3500/3700 tractor’s Weight Control Valve knob counter-

clockwise as far as it will turn to achieve the minimum weight transfer
setting. (Refer to tractor’s owner’s manual for complete information.)

5. Set the deck cutting height to 3.5” at the two front gauge wheel forks and

at the two rear height adjusting linkages.
(Refer to Cutting Height Adjustment section to set cutting height.)

6. Measure from the level surface to the top of the deck. Fig. 3-6

The top of the deck is 5.09” higher than the actual cutting height. Take
the measurements at each of the areas shown (Fig. 3-6) and subtract

5.09” from them. That will give the actual cutting height for that loca­tion.

Example: 8.59” (top of deck height)

-5.09”

(top of deck to blade distance)

3.50” (cutting height)

NOTE: The rear of the deck should be .2” - .5” higher than the front of
the deck.

3-2 109631_0908

7. If the measured cutting height is significantly different than the 3.5”

Rear height
adjustment

anchor

Rear height shown set at 2.5”

Rear height

adjusting yoke

Clevis pin

Measure
to top of

deck here

Measure
to top of

deck here

Measure
to top of

deck here

Measure
to top of

deck here

2”

2.5”
3”

4”

5”
6”

3.5”

4.5”

5.5”

Recesses on gauge

arm mount

Gauge wheel

assembly

Measure, then subtract 5.09”

Gauge arm

mount

Loosen cap screw
for adjustments of

less than 1/4”

When mower deck is set in the 2” – 6” range.

.25” Spacer

desired height than the front of the deck will have to be adjusted at the
two front gauge wheel forks. The rear of the deck will have to be
adjusted by moving the pins up or down in the adjusting holes. Refer to
Cutting hieght adjustment section for more detailed information.
NOTE: Minor leveling can be accomplished by moving the 1/2” cap
screw on either front gauge arm mount forward in the slot, to raise cut­ting height, or backwards to lower cutting height. Fig. 3-7

8. If one side of the deck is more than .25” higher than the other side, lower

the high side of the deck by transferring the .25” gauge w heel spacer
from under the gauge wheel fork bearing to the top side. (Fig. 3-8 and 3-

11)
Lower the rear of the deck .25” at the rear height adjustment pin one
hole. Fig. 3-9 and 3-13

9. The mower deck should now be level.

Cutting height adjustment

WARNING: Make sure PTO clutch switch is off, engage trac-

tor parking brake, stop engine, and remove ignition key before
making any adjustments to mower deck.

For best results, make cutting height adjustments on a hard flat surface.

The mower deck can be height adjusted in back as well as in front.

Fig. 3-6

Fig. 3-8

Fig. 3-9

The mower deck has two different cutting height range settings: 2” – 6”

or 1” – 5”. The deck is preset at the factory to the 2” – 6” setting.

Both front and rear height adjustment are in 1/4” increments.

For a quick check of height adjustments: Measure from level surface to
top of mower deck (as indicated in Fig. 3-7) and subtract 5.09 inches. The
balance will be blade height. To be sure mower deck is level, measure at
front and back on both left and right side of deck. Fig. 3-6

To adjust front cutting height

1. Park the unit on a flat surface, set the park brake and using the tractor’s

hydraulic system lift mower deck off the ground. Shut off tractor engine.

Place 8” tall blocks at the four corners of the deck. Restart engine and

lower the deck onto the blocks. Shut off tractor engine and remove key

from the igniton switch.

109631_0908 3-3

Fig. 3-7

WARNING: Stop engine. Remove ignition key before getting

off machine.

WARNING: The deck must rest on the blocks to prevent the
deck from being lowered suddenly by the accidental move­ment of the tractor’s tool bar lift control lever.

2. Pull up and forward on gauge wheel handle and lift or lower wheel to

desired height (Fig. 3-10). Both gauge wheels should be adjusted to

same height for uniform cutting.

NOTE: To change cutting height range setting to the 1” – 5” range,
reposition the two .5” spacers, located below the gauge wheel bearings, to
above the bearings. Fig. 3-11 & Fig. 3-12

NOTE: 2” – 6” cutting height range: Recesses on side of gauge arm
mounts visually indicate cutting height in 1/2” increments. Each notch
between recesses represents a 1/4” adjustment. When the bottom (lowest)
recess is just visible over top of gauge wheel assembly, cutting height is set
at 6”, when the mower deck is set in the 2” – 6” range (see Fig. 3-7). Next
mark up indicates 5-1/2”, then 5” and so forth. Top mark indicates 2”. Move
gauge wheel assemblies all the way to top of arms for 2” cutting height.

mounts visually indicate cutting height in 1/2” increments. When the bottom

.5” Spacers

.25” Spacer

.5” Spacers

Gauge wheel

fork

Handle

(lowest) recess is just visible over top of gauge wheel assembly, cutting
height is set at 5”, when the mower deck is set in the 1” – 5” range. Next
mark up indicates 4-1/2”, then 4” and so f orth. Top mark indicates 1”. Mo ve
gauge wheel assemblies all the way to top of arms for 1” cutting height.

closed (down) position, follow procedures outlined in Gauge Wheel Tension
Adjustment section of this manual.

To adjust rear cutting height

IMPORTANT: Deck cutting height will be affected by the use of the 3500/

3700 tractor’s Weight Control Valve. This allows the operator to transfer
weight from the front gauge wheels to the front drive wheels to increase trac­tion. Using this feature will result in the cutting height being increased and

Fig. 3-10

NOTE: 1” – 5” cutting height range: Recesses on side of gauge arm

If gauge wheels do not remain securely in place when handles are in

1. Park the unit on a flat surface, set the park brake and using the tractor’s

hydraulic system lift mower deck off the ground. Shut off tractor engine
and remove key from the igniton switch. Place 8” tall blocks under the
rear of the deck.
NOTE: The deck must be in the raised position to release pressure from
the lift chains

WARNING: Stop engine. Remove ignition key before getting
off machine.

WARNING: Placing the blocks under the rear of the deck will
help prevent injury in the event the deck is lowered suddenly
by the accidental movement of the tractor’s tool bar lift control
lever.

2. Remove the clevis pin from the rear height adjusting yoke. Locate the

appropriate hole in the yoke and in the rear height adjustment anchor and
insert the clevis pin through both and secure in place. Fig. 3-9 & Fig. 3­13
NOTE: Adjust the rear of the mower deck to match the front cutting
height setting.

3. Set the opposite side rear height adjustment using procedures in preced-

ing steps.

Fig. 3-11

Fig. 3-12

the deck pitch (angle from front to back of deck) being decreased. Addi­tional cutting height adjustments may be necessary if the W eight C ontrol fea­ture is used consistently.

Anti-scalp rollers

Anti-scalp rollers are standard on Hustler Front Mount mower decks.
These anti-scalp rollers are designed to minimize scalping when mowing on
rough uneven terrain. Fig. 3-1

After setting the cutting height, adjust the front anti-scalp roller so it
extends below the mower deck but does not contact the ground. It can be set
at either 3/4” or 1-3/4” 19.05mm to 44.45mm) below the cutting height. Fig.
3-14

The rear anti-scalp roller is not adjustable.

Mowing suggestions

The following list is not all inclusive. Additional suggestions can be
found in operation section of tractor manual.

1. Keep blades sharp. Many professional mowing companies have addi-

tional sets of blades and change blades twice a day: once in the morning

and again at noon. Many problems with incorrect cutting patterns are

due to dull blades or blades which have been sharpened incorrectly.

Information on sharpening blades is listed in this manual’s maintenance

section. In addition, most communities have individuals or companies

which specialize in sharpening mower blades. Blade sharpness should

be checked daily.

3-4 109631_0908

Front anti-scalp wheel

Mount hole

Rear height

adjustment anchor

+.75”

+.50”

+.25”

+0”

6” 5” 1”4” 3” 2”

Fig. 3-13

2. Use high blade speed. Your Hustler tractor and mower are designed to

operate at full throttle. As explained in tractor manual, throttle setting
directly controls blade speed. The highest blade speed generally gives
best cut.

3. Direct grass discharge to right, away from unmown area. Select a

mowing pattern that directs grass discharge towards the outside, not
towards center, of mowing area. Generally, this means using a pattern
utilizing left turns because side discharge is to right. In any case, avoid

Fig. 3-14

throwing grass discharge onto unmowed area because grass is then
mowed “twice”. Mowing twice puts an unnecessary load on tractor and
reduces mowing efficiency.

4. Avoid sudden turns on wet turf. These can damage turf unnecessarily .

5. Never raise the mower deck with the blades engaged to avoid small
obstacles, drive over curbs and so forth. Disengage the PTO before rais-
ing the deck, using the tractor’s tool bar lift control lever. See tractor
owner’s manual for additional information.

6. Always check area to be mown for rocks and other debris before mow-

ing and remove them from operator’s path.

109631_0908 3-5

3-6 109631_0908

MAINTENANCE

Safe Servicing Practices

This product is capable of amputating hands and feet and throwing

objects. Always follow all safety instructions to avoid serious injury or death.

Service

V Unless specifically required, DO NOT have engine running when ser-

vicing or making adjustments to tractor. Park the machine on level
ground. Place park brake lever in the brake engaged position, place the
PTO lever in the “OFF” position, lower deck, remove ignition switch
key and disconnect negative battery cable before doing any mainte­nance. Wait for all movement to stop before adjusting, cleaning or
repairing. Repairs or maintenance requiring engine power should be
performed by trained maintenance personnel only. To prevent carbon
monoxide poisoning, be sure proper ventilation is available when
engine must be operated in an enclosed area. Read and observe safety
warnings in front of manual.

V Before working on or under the deck, make certain engine cannot be

accidentally started. Shut engine off, remove ignition switch key and
disconnect negative battery cable for maximum safety. Repairs or
maintenance requiring engine power should be performed by trained
maintenance personnel only.

V Except when changing or checking belt, always keep belt covers on

mower deck for safety as well as cleanliness.

V Use a stick or similar instrument to clean under the mower deck mak-

ing sure that no part of the body, especially arms and hands are un der
mower. It is advisable to pivot the deck up and lock in place before
cleaning.

V Clean flammable material from machine. Prevent fires by keep-

ing the top of the deck, under deck covers, engine compartment,
exhaust area, battery, hydraulic lines, fuel line, fuel tank and oper­ator’s station clean of accumulated trash, grass clippings, and
other debris. Always clean up spilled fuel and oil.

V Always wear adequate eye protection when servicing the hydraulic

system and battery, or when grinding mower blades and removing
accumulated debris.

V Never run the engine in an enclosed area unless exhaust is vented to

the outside. Exhaust gases contain carbon monoxide which is odorless
and deadly poison.

V Never attempt to make any adjustments or repairs to the mower deck

while the tractor engine is running or PTO is engaged. Mower blades
cannot be seen and are located very close to the deck housing. Fingers
and toes can be cut off instantly.

V Never attempt to make any adjustments or repairs to the tractor drive

system, mower deck or any attachment while the tractor engine is run­ning or PTO is engaged. Repairs or maintenance requiring engine
power should be performed by trained maintenance personnel only.

V Never work under the machine or attachment unless it is safely sup-

ported with jack stands. Make certain machine is secure when it is
raised and placed on the jack stands. The jack stands should not allow
the machine to move when the engine is running and the drive wheels
are rotating. Use only certified jack stands. Use only appropriate
jack stands, with a minimum weight rating of 2000 pounds to block
the unit up. Use in pairs only. Follow the instructions supplied with
the vehicle stands.

V Do not touch hot parts of machine.
V Keep nuts and bolts tight, especially the blade attachment bolts. Keep

equipment in good working condition.

V Never tamper with safety devices. Check their proper operation regu-

larly.

V Stop the engine before removing the grass catcher or unclogging the

discharge chute. Never clear the discharge chute with the engine run­ning. Turn off the engine and be sure the blades have stopped before
cleaning. Use a stick to clear a plugged discharge area. Never use

your hand!

V Grass collection system components are subject to wear, damage and

deterioration, which could expose moving parts or allow objects to be
thrown. Frequently check components and replace with manufac­turer’s recommended parts, when necessary.

V Exercise caution when working under the deck as the mower blades

are extremely sharp. Wrap the blade(s) or wear gloves and use extra
caution when servicing them.

V Use only genuine Hustler replacement parts to ensure that original

standards are maintained.

109631_0908 4-1

Item No. Description

Check or

Maintain

1 Blades (3) — sharp and securely fastened Daily
2 Tires — properly inflated Daily
3 Gearbox — sufficient lubrication* Daily **
4 Discharge chute — securely in place Daily
5 Clean clippings from under side of mower

housing and under the deck covers. Clean
more often when grass is moist

Daily

6 Proper tension on gauge wheel arms Every 150 hours
7 Gauge wheel bearings Weekly or Every

50 hours.
8 Belt — proper tension, belt servicable Every 100 hours
9 PTO shaft (3) — Lubricate using all purpose

lubricant. Do not force lubricant into grease
zerks.

Every 100 hours

10 Spindle housings (3) — Lubricate using all

purpose lubricant. Do not force lubricant into
grease zerks.

Annually or Every

750 hours.



































* ISO VG 46
** Check daily and change every 6 months.



Maintenance Locator Chart

Figure 4-1

4-2 109631_0908

Introduction

Sight gauge

Plug

Locking pins

Rear height adjusting chain

Regular maintenance is the best prevention for costly downtime or
expensive, premature repair. The following pages contain suggested mainte­nance information and schedules which the operator should follow on a rou­tine basis. For more detailed information refer to the correct parts manual for
your unit.

Remain alert for unusual noises, they could be signaling a problem.
Visually inspect the machine for any abnormal wear or damage. A good time
to detect potential problems is while performing scheduled maintenance ser­vice. Correcting the problem as quickly as possible is the best insurance.

Clear away heavy build-up of grease, oil and dirt, on top of the deck and
under the deck areas especially under the deck guards.

Daily inspect mower deck for grass clippings and wire and string tangles.
The underside of the mower deck will collect a build-up of grass clippings
and dirt, especially when grass is wet or has high moisture content. This
build-up will harden, restricting blade and air movement and will probably
show a poorer quality of cutting. Therefore it should be removed routinely.

To do this it will be necessary to pivot the deck to the full up position and
scrape the build-up from underneath. See Mower Deck Tilt Procedure sec-
tion.

Some repairs require the assistance of a trained service mechanic and
should not be attempted by unskilled personnel. Consult your Hustler service
center when assistance is needed.

Description of operation

The three mower blades are indirectly driven by the tractor engine:
Power flows through the mechanical clutch, PTO drive shaft, right angle
gearbox, and finally through a V-belt drive system. The V-belt drives three
pulleys; each pulley is on top of a spindle housing assembly. The pulleys
drive 1” spindle shafts which in turn drive the blades. A blade is affixed to
each spindle shaft by a 5/8” bolt.

The mower deck is connected to tractor by attaching the mower tool bar
arms to the tractor tool bar with clevis pins and hairpins.

1. Park the unit on a flat surface, raise mower deck and set the parking

brake.

2. Shut off engine and remove the ignition key.

3. Pull out on the locking pins attached to the rear height adjusting chains.

This allows the rear of the mower deck to move freely. Fig. 4-3

4. Lift the front of the mower deck and pivot it until the holes in the deck

and carrier arms are in alignment. Remove the locking pin from the stor­age hole and insert it thru the holes in the deck and carrier arm. Fig. 4-4
and 4-5

WAR NI NG : Until the deck is fully pivoted and locked in the
tilted position with the locking pin, it will fall if accidental
movement of the tractor’s tool bar lift control lever occurs.

WAR NI NG : The locking pin must be inserted thru both sides
of the carrier arm to prevent the deck from falling.

5. Lower the mower deck until the rear anti-scalp roller rests on the ground.

Fig. 4-6

6. When finished working on the underneath side of the deck, reverse the

procedure and lock the deck in the mowing position before operating the
unit.

Cleaning mower deck

DANGER: Before cleaning under mower, make sure the PTO

Control Lever is in the “OFF” position. Raise the mower deck
to highest position and engage parking brake lever. Turn off
engine. Pin deck up in the tilted position using the locking pin.
Lower the mower deck until the rear anti-scalp roller rests on
the ground.

Torque values

WARNING: Particular attention must be given to tightening

the blade spindle bolts. Failure to correctly torque these items
may result in the loss of a blade, which can cause serious dam­age or personal injury.

Torque values are given below:

Spindle blade bolt (bottom) . . . . . . . . . . . . . 118 . . . . . . . . .160.01

Spindle pulley bolt (top) . . . . . . . . . . . . . . . .75. . . . . . . . . .101.68

For all other torques refer to the deck parts manuals for stan dard torque
chart.

Tires

It is important for level mowing that the tires have the same amount of air
pressure. The recommended pressure is:

Front gauge wheels . . . . . . . . . . . . . . . . . . . . . 8-12 psi (55-83 KPa)

Solid fill tires are not recommended for Hustler turf equipment. On
any machine, with solid filled tires, the warranty claim will be denied.

Lubrication

Check gearbox lubricant daily by looking at the sight gauge located on
side of gearbox. It should appear half full. Fill as necessary with ISO VG46
oil (Hustler P/N 601621). Fill by removing pipe plug located on top front of
gearbox. Add oil until the sight ball floats off of the bottom. Fig. 4-2

Spindle housing, under mower. Lubricate spindle housings annually or
after every 750 hours of operation, whichever occurs first. Use no more than
one or two ounces of multi-purpose lubricant. Do not force lubricant into
grease zerks. Bearings are sealed and do not require much lubrication.

Mower deck tilt procedure

The mower deck is designed to be raised and pinned in an upright posi­tion to allow easier access to the underneath side of the mower deck.

Ft-lbs. Nm

Figure 4-2

Figure 4-3

109631_0908 4-3

Locking pin -

Storage position

Figure 4-4

Locking pin -

Deck locked position

Deck in tilted position

Rear

anti-scalp

roller

Figure 4-5

Replace any blade which is bent, cracked or broken.

WARNING: Never attempt to straighten a bent blade by heat­ing, or weld a cracked or broken blade as the blade may break
and cause serious injury. Replace worn or damaged blades.

DANGER: Never work with blades w hile engine i s ru nnin g or
the PTO Control Lever is in the “ON” position. Always put
PTO Control Lever in “OFF” position, engage parking brake
and turn engine off. Pin mower up when you must work under
it. Wear gloves when handling blades. Always check for
blade damage if mower strikes rock, branch or other foreign
object during mowing!

WARNING: Always wear adequate eye protection when grind­ing mower blades.

Mower blade removal

Use a 15/16" wrench to remove the 5/8" cap screw holding the blade to
the spindle shaft from underneath. NOTE: A blade holding tool (part num­ber 381442) is available from Hustler Turf Equipment. It is designed to pre­vent the blades from rotating when they are being removed or installed on the
spindle. Contact your Hustler dealer for more information.

Sharpen the blades on a grinder following pattern as shown (Fig. 4-7).
Touch-up sharpening can be done with a file.

Check the blades for balance following grinding. A commercial balanc­ing tool is available through most hardware supply stores, or balancing can be
done by placing the blade on an inverted line punch or 1/2" bolt. Blade
should not lean or tilt. Spin the blade slowly, blade should not wobble. If
blade is out of balance, true it up before reinstalling.

Lay the blade on a flat surface and check for distortion (Fig. 4-8 and 4-9).
Replace any distorted blade.

Do not re-use spindle bolts which have stripped, worn or undercut
threads. T or que spindle bolts to 118 ft-lbs. when reinstalling blades.

IMPORTANT: When mounting blades, rotate them after installation to
ensure blade tips do not touch each other or sides of the mower .

WARNING: Failure to correctly torque the bolt may result in
the loss of the blade which can cause serious injury.

Figure 4-6

WAR NI NG : When possible clean under mower, using a stick

or similar instrument making sure that no part of the body,
especially arms and hands are under mower.

Daily, inspect mower for grass clipping build-ups, wire and string tan-

gles. Underside of mower housing will collect cut grass and dirt more rapidly
on moist days. Check it frequently when grass is moist. Otherwise, clean
under housing once a day for maximum efficiency.

Blade maintenance

Check the mower blades daily, they are the key to power efficiency and
well groomed turf. Keep them sharp, a dull blade will tear rather than cut the
grass, leaving a brown ragged top on the grass within a few hours. A dull
blade also requires more power from the engine.

WARNING: Mower blades ar e sharp and can cut. Wrap the
blade(s) or wear gloves and use extra caution when servicing
them.

Belt maintenance & adjustment

The blades in the mower are driven by a V-belt. Belt tension is main­tained by use of a spring loaded idler pulley. As belt stretches and wears in,
additional tension may become necessary. To increase belt tension, move the
spring chain one (or more) link(s) at the anchor bracket (Fig. 4-10). Installed
spring length should be as shown in Fig. 4-11. When the belt is re-tensioned
each chain link allows approximately .60" (15.2mm) of adjustment.

IMPORTANT: Do not over tension the spring to compensate for a badly
worn belt or pulley.

Belt should be visually inspected every 100 hours for wear and service­ability. To replace, relieve tension on idler pulley, remove old belt and install
new belt following pattern indicated on maintenance illustration (Fig. 4-1).
Following are some maintenance suggestions:

1. Maintaining proper belt tension gives more economical performance and

longer belt life. Replacement belts may be seriously damaged if machine

is operated before belts are properly adjusted.

2. All V-belts stretch when new. Check belt tension after 1 to 3 hours of

running when belts are new.

3. For better belt life and service, keep belts properly adjusted at all times:

• A loose belt may not slip noticeably, but at the same time it may be
wearing belt and pulley groove excessively. (Sluggish performance is
typical symptom of this problem.)

• If belt slips, excessive heat generated will shorten belt life.

• More belts are ruined by lack of tension than by too much tension.

4. A slight raveling of belt covering does not mean failure. Raveling should

be cut off.

5. Never use belt dressings on V-belts.

4-4 109631_0908

Handle pin

Set screw

Handle

Lock pin

Spring

Lock

Spare spring washer

Cotter pin

linkage

washers

Spring Extension

8.1 - 9.1”

Spring

Chain

Anchor
bracket

Cutting Edge

Cutting Plane

Cutting Edge

Twisted Blade Edge (Replace)

Straight Blade Edge

End view of blades, comparing twisted and straightened blades.

Warped Blade (Replace)

Straight Edge

Comparison of Warped and Straight Blades

Cutting

Plane

Do not sharpen to original pattern (below)

It is easier to get a straight cutting edge following

the resharpening pattern shown above.

Resharpening

Pattern

Original Edge

Figure 4-7

Fig. 4-8

Fig. 4-10

Fig. 4-11

6. Keep oil and grease away from belts.

7. When replacing belts, check pulley groove condition. A worn groove

(notch in shoulder) will cause rapid belt failure. Replace pulley if
groove is worn.

8. Never pry belt over edge of pulley, this may cause fiber s of belt to b reak.

9. Sun and weather injure belts, unnecessary exposure to these elements

should be avoided whenever possible.

Gauge wheel tension adjustment

Gauge wheel arms are held in place against the gauge wheel arm mount
by lock linkage and lock pin. Tension on arms is controlled by spring wash­ers. There are 15 washers on each arm: 14 are between the lock linkage and
lock pin and 1 is a spare, placed in front of the lock linkage as shown in Fig.
4-12.

NOTE: Seven of the spring washers are turned one way and the other
seven are reversed. The concave part of the two sets of washers should face
each other. This is what provides the tension. Fig. 7-13

If gauge wheels do not stay firmly in place when handle is in down
(closed) position:

1. Relieve tension on lock pin and linkage by removing handle, lock link-

age and lock pin from gauge wheel arm assembly.

2. Remove cotter pin from lock pin and insert one or two spare washers

between lock linkage and lock pin.

3. Reassemble gauge wheel arm by reversing above directions.

NOTE: If more tension is needed, additional spring washers may be
purchased from your Hustler Dealer.

109631_0908 4-5

Fig. 4-9

Fig. 4-12

These spring washers

These spring washers

face the other direction

face one direction

Fig. 4-13

Tire care

Visually inspect gauge wheel tires daily to ensure proper inflation.
Gauge wheel tire inflation directly affects mower cutting height. Proper
pressure is 8-12 psi.

End of season storage

Read and follow suggestions in tractor’s owner manual. As a minimum:

1. Clean off dirt and debris.

2. Check lubricant level in gearbox.

3. Check for broken, worn parts and replace or repair as necessary.

4. Touch up scrapes with spray paint and lubricate exposed metal to prevent

rust and corrosion.

5. Make sure tires are elevated off ground or floor. Do not deflate tires.

6. Store mower in clean, dry area.

4-6 109631_0908

TROUBLESHOOTING

The majority of operating problems that occur with a system can be traced
to improper adjustments or delayed service. A consistently applied preven­tive maintenance program, as outlined in the maintenance section of this
manuel, will prevent many problems. The following chart is designed to help
you locate a problem by suggestin g probable causes and recommended solu­tion(s).

The suggested remedies should be applied with care. Make certain that the
source of a problem is not located someplace other than where the problem
exists. A thorough understanding of the system is a must if operating prob-

SYMPTOMS PROBABLE CAUSES SUGGESTED REMEDIES

Tractor is sluggish, veers in
one direction, etc.

Uneven Grass Cut Tire inflation varies (tractor or deck) Check and adjust tire pressures.

Mower leaving skip between
blades

Deck belt shows excessive
wear

Smoke in mower deck (espe­cially while cutting in heavy
grass)

Blades not turning Deck belt broke or too loose Check belt

Excessive noise Blades not tight Tighten blades

One blade cutting smoother
than other blades

Numerous Refer to tractor owner’s manual

Gauge wheels incorrectly adjusted Check and correct gauge wheels

Blades vary in sharpness Ensure all blades are properly sharpened

Blades improperly installed after sharpening Ensure blades are properly installed

Rear height adjustment improperly adjusted Check and correct rear height adjustment

Blades dull or too short Check blade sharpness and length

Deck belt too loose Tighten belt

Deck belt too loose Tighten belt

PTO lever in “OFF” position or shaft improperly
connected.

Deck is in raised position, PTO automatically dis­engaged

Blades touching sides or each other Check blade clearance

Spindle assemblies loose Tighten bolts on assembly

Beginning of spindle bearing failure Replace spindle bearings

Damaged deck housing Remove dents, etc.

Engine or tractor noise See engine and tractor manual

Belt loose Tighten belt

lems are to be converted satisfactorily. A good rule to follow in locating trou­ble is to never make more than one adjustment at a time, then locate trouble
by a process of elimination. Remember the cause is usually simple, rather
than mysterious or complicated. Separate troubleshooting guides are
included in engine and tractor owner’s manuals.

Operators handling the same equipment every day soon develop a sense of
impending trouble when abnormal operation occurs. Immediate attention to
these danger signals can prevent major failures, ensure dependable operation
and increase the life of equipment.

Check PTO lever, PTO switch wiring and shaft con­nections

Lower deck and reengage PTO drive

109631_0908 5-1

5-2 109631_0908

INDEX

PAGE PAGE

Anti-scalp rollers
Attaching mower deck to tractor
Belt maintenance & adjustment
Blade maintenance
Cleaning mower deck
Cutting height adjustment
Gauge wheel tension adjustment
Introduction
Leveling mower deck
Lubrication
Model and serial number
Mower blade removal
Mower deck tilt procedure

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Mowing suggestions
Operation
Parts and service
Safe Operating Practices
Safe Servicing Practices
Safety and Instruction Decals
Service
Tires
To the new owner
Torque values
Using a ramp
Using this manual
Warranty registration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

109631_0908 1-1

1-2 109631_0908