Husqvarna ST 121E User Manual
ILLUSTRATED PARTS LIST
MODEL NUMBER ST 121E
PRODUCT NUMBER 961 83 00-01
MFG. ID. NUMBER 96183000101
580 47 26-32
REPAIR PARTS SNOW THROWER - - MODEL NUMBER ST 121E (96183000101)
AUGER ASSEMBLY
1
5
10
12
9
10
7
6
8
11
10
12
2
10
3
4
12
10
2
11
5
3
10
12
12
7
1
11
11
06.03.001-D
KEY PART
NO. NO. DESCRIPTION
1 532 44 27-59 BLADE
2 580 85 55-01 BEARING SUPPORT
3 532 43 76-22 BALL BEARING
4 812 00 00-28 RETAINING RING
5 817 06 04-08 1/4-20 X 3/8 HEX SCREW
6 532 43 76-17 AUGER WELDMENT
7 580 85 54-01 CENTER BLADE PLATE
8 532 43 76-20 ROLL PIN
9 532 19 96-87 SCREW HEX WS HD 1/4-20 X 1.5
10 872 11 04-07 BOLT CARRIAGE 1/4-20 X 7/8
11 819 09 10-16 WASHER FLAT 1/4 SAE
12 532 13 20-04 NUT HEX 1/4-20 BZO
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
2
REPAIR PARTS SNOW THROWER - - MODEL NUMBER ST 121E (96183000101)
CHUTE ASSEMBLY
2
4
7
8
9
5
6
1
3
KEY PART
NO. NO. DESCRIPTION
1 532 43 76-55 CHUTE (BLACK)
2 532 43 76-43 DEFLECTOR (BLACK)
3 873 97 05-00 NUT LOCK HEX W/INS 5/16-18
UNC PL
4 532 13 20-04 NUT HEX 1/4-20 NYLON
LOCKING
5 532 44 46-82 SHOULDER BOLT 1/4-20 HEX
HEAD
6 872 11 05-10 CARRIAGE BOLT 5/16-18 X
1-1/4
7 819 13 13-16 WASHER 13/32 X 13/16 X 16
GA
8 532 44 50-19 WING KNOB
9 532 07 16-73 CAP PLUNGER
10 872 01 05-06 CARRIAGE BOLT 5/16-18 UNC
X 1
3
06.05.003-C
10
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
3
REPAIR PARTS SNOW THROWER - - MODEL NUMBER ST 121E (96183000101)
HANDLE ASSEMBLY
3
9
8
7
10
4
6
11
1
2
5
06.09.001-A
KEY PART
NO. NO. DESCRIPTION
1 532 44 27-75 RH LED SUBASM
2 532 44 27-76 LH LED SUBASM
3 581 00 88-01 SHROUD CONTROL ASM
4 532 14 50-06 PUSH IN CLIP
5 817 41 13-12 SCREW HI-LO 3/4”
6 817 41 13-18 SCRWE HI-LO 1-1/8
7 532 44 30-46 WIRING HARNESS
8 580 40 21-01 HARNESS JUMPER
9 532 44 32-45 SHROUD ASM SM
10 532 44 16-24 SHROUD LARGE
11 819 09 10-16 WASHER FLAT 1/4 SAE
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
4
REPAIR PARTS SNOW THROWER - - MODEL NUMBER ST 121E (96183000101)
HANDLE ASSEMBLY
2
7
12
12
21
25
24
26
3
27
23
24
25
5
6
5
6
4
11
17
8
9
25
24
4
18
19
10
1
11
8
13
14
16
21
15
3
22
17
06.07.005-A
KEY PART
NO. NO. DESCRIPTION
1 532 44 34-32 UPPER HANDLE ERGO GRAY
2 532 44 34-33 OVERMOLD BAIL ASM HUSQ
3 532 44 30-21 QUICK ADJUST SUBASM
4 532 19 92-55 STUD QUICK ADJ
5 532 44 22-48 NUT 5/16-18 FLANGE NYLOCK
BLACK
6 873 97 05-00 NUT LOCK HEX FLANGE
7 532 43 75-06 DECAL HANDLE BAR AUGER
INSTRUCTIONAL
8 532 44 39-38 CHUTE RETAINER RING
9 532 44 39-39 CHUTE BASE DCC BLACK
10 532 44 39-40 PULLEY DCC RING BLACK
11 532 43 68-06 BRACKET CABLE DCC
12 532 43 68-05 CABLE DCC
13 532 43 68-90 HANDLE SUDASM PIVOT
14 532 44 28-35 HANDLE GRIP SUBASM
15 532 44 47-49 WASHER THREE WAVE
SPRING
20
KEY PART
NO. NO. DESCRIPTION
16 532 43 54-17 NUT PUSH AXLE .05”
17 817 41 13-12 SCREW HEX WSHHD #13 X .750
18 580 66 45-01 CHUTE CONTROL SPRING
ROTATE
19 532 43 48-78 CHUTE RATCHET ARM
20 580 85 56-01 CHUTE BASE PLATE
21 532 44 22-50 SCREW PAN HD TORX
1/4-20 X .750
22 532 14 50-06 CABLE GUIDE
23 580 85 59-01 SUPPORT BRACKET DDC
STAMP
24 532 18 44-71 SCREW SHOULDER 10/24 X .62
25 810 04 04-00 LOCKWASHER 1/4 SPLIT
26 532 44 22-34 ROPE GUIDE
27 532 13 20-04 NUT HEX 1/4-20 BZO
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
5
Loading...