Husqvarna QG Owner's Manual

ADJ U ST T HE MOWE R TO S UIT YOU R G ARD E N

See chapters 6.4 and 6.5 in the Operator’s Manual.

Here you will nd a few tips about important settings for your Automower®. All settings for Automower® are made using the menu functions.

ADJUST THE MOWER TO SUIT THE SIZE OF YOUR LAWN

The mowing results depend on mowing time. Adjust the mowing time to suit your garden using the Timer function.

If the mower works too often: The lawn will appear trampled down. If the mower works too seldom: The lawn will not be properly cut.

ADJUST THE MOWER FOR NARROW PASSAGES

Narrow passages in the garden make it difcult for the mower to nd the charging station. Test to see if the mower nds its way home using the Test IN function.

1. Look for the narrowest passage in the garden (between the boundary loops).

2. Place the mower beyond the passage, with its front facing the boundary loop.

3. Activate the Test IN function (Garden - Follow loop - Test IN) and start the mower.

4. Ensure that the mower follows the boundary loop through the passage.

a. If the mower travels through: The test is complete. a. If the mower does not travel through: Lower the value

of the Corridor width, boundary by 1 unit. Restart the test from point 2.

TIMER

You decide what times of the day and days of the week the mower is to work. Automower If your garden consists of 3,000 m² / 0.75 acre of grass, the mower should work, on average, 12 hours per day.

SMS

For increased control of Automower® there is an SMS function that enables the mower to communicate with its user (See chapter 6.6 in the Operator’s Manual).

cuts around 250 m² / 2,200 ft² per hour and day.

1 4A

CORRIDOR WIDTH , BOUN DARY

Settings Corridor width, boundary (Garden- Follow loop - Corridor width - Corridor width, bound.) denes the distance bet ween the mower’s path to the boundary

wire or the guide wire when following these to/from the charging station. The wider the stated Corridor width, the further from the loop the mower can travel. This produces less wheel tracks than if the mower were to travel close to the loop.

GUI DE WIRE

See chapter 3.8 Installation of the guide wire in the Operator’s Manual.

If you have a complicated garden or it has narrow passages (less than 2 m / 7 ft), we recommend installing a guide wire.

Main menu

Comm ands Time r Gard en Set tings

Garden - Follow loo p - Test IN

The guide wire is an extra wire that is run from the charging station, out towards a remote part of the work area or through a narrow passage. The mower can follow the guide wire to and from the charging station.

QUICK GUIDE

HUSQVA RNA AUTO MOWER

265 ACX

115 42 55- 95

www.automower.com

GE TTI NG START ED

WITH HU SQVA RNA AUTOMOWE R

PLACE ME NT A ND CON N ECT I NG THE CH A RGI N G S TAT ION

See chapter 3.2 in the Operator’s Manual

1. Place the charging station centrally in the work area, leaving a lot of free space in front of the charging station and on a relatively horizontal surface.

2. Connect the low voltage cable to the charging station and

transformer.

3. Connect the transformer’s power cord to an electrical wall

socket. The 120 V transformer (USA) is for indoor use only.

CH A RGI N G T H E BATTE RY A ND PLACI NG T HE BOUN DA RY WI RE

See chapters 3.3 and 3.4 in the Operator’s Manual.

1. Place Automower® in the charging station to charge the battery while you are laying the boundary wire. Set the main switch to the OFF position.

2. Run the boundary wire ensuring it

forms a loop around the work area.

0 cm / 0 "

10 cm / 4 "

CON NEC T ING THE BOUN DARY WI R E

See chapter 3.5 in the Operator’s Manual

1. Lift off the cover on the charging station and push in the ends of the boundary wire in the lower holes of the charging station and catch them in the upper holes:

• Right wire end in right hole.

• Left cable end in left hole.

2. Open the connector and run the wire ends in the recesses on each connector.

3. Press the connector together using a pair of pliers.

4. Cut off any surplus boundary wire. Cut 1-2 cm / 0.5-0.78" above the connector.

5. Press the connector onto the contact pin, marked A, on the charging station. Ret the cover on the charging station.

STARTI NG A ND STOPPI NG AUTO M OWER

See chapters 3.7, 4.4 and 4.5 in the Operator’s Manual.

4 5

STARTING

35 c m / 14 "

1. Chargin g st rip

2. Lat ch button to open the cut ting height adjustment cover

3. STOP button

4. LED for per for mance inspe ction of b oundary wire

5. Contact st rips

6. Keypad

7. Display

6 7

Main menu

Commands Timer Garden Settings

40 cm / 15"

Chargin g st ati on Trans former Low volt age cab le Boundary wire *

1. Open the control panel cover by pressing the STOP button.

2. Set the main switch to ON position. When you do this for the rst time, a start up sequence starts where you select a four digit PIN code among other things. The mower must be in the charging station when you select a PIN code.

3. Close the cover.

STOPPING

Press the STOP button.

Pegs * Connector Mea sure men t gauge

and connect or

* Not included in package