For Husqvarna Parts Call 606-678-9623 or 606-561-4983
Swivel Wheel Accessory
Instruction Sheet
SWIVEL WHEEL ACCESSORY KIT
Kit No. 606 00 00-02
For use on
PACKAGE CONTENTS
Check the contents of your kit for the parts listed below
(Figure 1):
Item Qty Description
1 2* Wheel Yoke Weldment
2 1* Left Mount Arm Weldment
3 2 Axle Tab
4 2 Pin-Clevis .25 x 1.75
5 2 Clevis Pin
6 2* Fitting-Lube .25-28 x .256
7 2 Bushing-Flange .500 x .625
8 4* Bushing-Sleeve .625 x .750
9 2* Ring-Retaining-External
10 6 Bolt-Round Head Square
11 2* Washer-Flat-Steel .630 x
12 6 Nut-Locking Center .31-18
13 2 Pin-Hair Ext. .12 x .31 x 2.37
14 2 Kickout Ring 606 00 01 45
580 / 600 Series
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in personal
injury and/or damage to unit.
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning.
1* Right Mount Arm Weldment
x .500 x .750
x .500
.625 x .042
Neck .31-18
1.005 x .062
Walk Behind Mowers
Husqvarna P/N
606 00 02 63
606 00 02 65
606 00 02 64
606 00 01 43
606 00 01 56
606 00 01 44
606 00 01 49 (Not used with steel wheels)
606 00 01 51
606 00 00 82
606 00 01 53
606 00 01 57
606 00 01 50
606 00 00 50
606 00 01 55
Husqvarna
*Pre-assembled
Husqvarna
© Copyright 1999
Ariens Company • P.O. Box 157 • Brillion, WI 54110-0157
www.mymowerparts.com
08474000B 11/99 Page 1 of 2
For Husqvarna Parts Call 606-678-9623 or 606-561-4983
9. To change front wheel cutting height, insert clevis pin,
into the holes that corresponds to desired cutting
height (Figure 2).
10. To change rear wheel cutting height, move cutting
height levers one notch at a time until desired cutting
height is obtained (Figure 2).
9
DANGER: MOVING BLADES will sever and
amputate body parts. DO NOT place limbs
near moving parts.
NEVER attempt to make any cutting height
adjustments while the engine is running.
NEVER attempt lubrication or maintenance
procedures while engine is running.
MOWER ROLL AWAY will cause injury or
death. Swivel wheels must be in locked
position when mowing laterally on hill sides.
TRACTION DRIVE may not clutch or operate
properly and cause injury. Both rear wheels
must be positioned at same height on selfpropelled models.
14
10
11
8
4
2
6
12
1
5
13
3
Front Wheels
From Mower
Figure 1
IE0110
INSTALLATION
1. Remove spark plug wire.
2. Remove complete front axle assembly from mower
deck.
3. Disassemble front wheels from axle assembly.
4. Attach right and left hand assemblies to mower deck
with (6) carriage bolts and (6) flange whizlock-nuts
provided, tighten hardware to 10-12 lbs/ft (Figure 1).
5. Insert front wheels in swivel assembly front yokes
using clevis pin,
6. Insert clevis pin in either clevis pin storage hole or
swivel lock hole. Secure clevis pin with kickout ring
(Figure 1 & 2).
7. Place mower in normal operating position.
8. Reattach wire to spark plug.
NOTE: All wheels must be set at the same height for a level
cut.
• Low Setting -1 1/4" Cut grass length
• Second Setting - 1 3/4" Cut grass length
• Third Setting - 2 1/8" Cut grass length
• Fourth Setting -2 5/8" Cut grass length
• Fifth Setting - 3" Cut grass length
• Highest Setting - 3 1/2" Cut grass length
axle tab
, and hair pin
(Figure 1).
11. Move wheels or levers in direction shown for lower or
higher cutting heights.
12. Grease swivels every 10 hours of use.
NOTE: Swivels must be in locked position while lubricating.
Apply Sten Mix Hi-Temp Grease or equivalent to lube fittings. Order P/N: 00036800 - three pack of 3 oz. cartridges
or 00036700 - ten pack of 14 oz. cartridges.
4
Low
High
1. Cutting Height Lever
2. Notch
3. Swivel Height
4. Grease Fitting
5
Adjustment Holes
Low
1
6
2
3
5. Swivel Lock Hole
(Linchpin through to
lock)
6. Linchpin Storage Hole
(Linchpin through to
swivel)
Figure 2
High
IE0140
www.mymowerparts.com
08474000B 11/99 Page 2 of 2
Loading...