Husqvarna 142, 137 Owner’s Manual

Husqvarna /

Instruction Manual

Manual de Instrucciones

Manuel d'lnstructions

137 / 142

WARNING:

Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.

ADVERTENClA:

Lea el manual de instrucciones y siga todas las advertencias e en- strucciones de seguridad. El no hacerlo puede resultar en lesiones graves.

AVERTISSEMENT:

Lire le manuel d'instructions et bien respecter tousles avertisse-

ments et routes les instructions de securite. Tout defaut de le faire

pourrait entra_ner des blessures graves.

530165144 3/1/06

1 2 3

5-- 7

_ 11 10

1. Cylinder Cover 13. Bar Tip Sprocket

2. Front Handle 14. Saw Chah_

3. Front Hand Guard 15. Saw Bar

4. Starter Cover 16. Chain Catcher

5. Chain Oil Tank 17. Chain Brake Assembly

6. Starter Handle 18. Rear Hand Guard

7. Carburetor Adjusting Screw 19. Throttle Control/Trigger

8. Choke Control 20. Throttle Lock

9. Rear Handle 21. Bar/Chah_ Adjustment Tool

10. ON/STOP Switch 22. Chain Tensioning Screw

11. FueITank 23. Instruction Manual

12. Muffler 24. Guide Bar Cover

WARNING! This chain I_1

saw can be dangerous! Care- less or improper use can cause

serious or even fatal injury.

Always wear appropriate ear protection, eye protection and head protection.

Always use two hands when operating the chain saw.

f_l

Read and understand the instruction manual before

using the chain saw.

WARNING! Contactingtheguidebartipwithanyobject

should be avoided; tip contact may cause the guide bar to move suddenly upward and backward, which may cause se-

rious injury.

Measured maximum kickback value without chain brake for the bar

and chain combination on the label

Starting Reminder

Slide "ON"

Move ON/STOP switch to the ON position.

HalfChoke

Push the choke/fast idle

lever in to the HALF CHOKE position,

FullChoke

(2)'_

Pull 5X

_b,--bl

Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

Pull the starter rope sharply 5 times with your

right hand,

,_ WARNING: Always disconnect

spark plug wire and place wire where itcan- not contact spark plug to prevent accidental

starting when setting up, transporting, ad- justing or making repairs except carburetor

adjustments. Because a chain saw is a high-speed wood- cutting tool, special safety precautions must be observed to reduce the risk of accidents,

Careless or improper use of this tool can cause serious injury.

PLAN AHEAD

• Read this manual carefully until you com- pletely understand and can follow all safety rules, precautions, and operating instruc-

tions before attempting to use the unit.

• Restrict the use of your saw to adult users who understand and can follow safety

rules, precautions, and operating instruc- tions found in this manual.

Hearing Safety Hat

Protection _ Eye

"'_"_ I W'O _" Protection Snug Fitting Heavy Duty

Clothing Gloves

Safety Safety Chaps Shoes

• Wear protective gear, Always use steeF toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip gloves; eye protection such as non-fog-

Pull the starter rope sharply

with your right hand until

Pull to Start

• Keep all parts of your body away from the

• Keep children, bystanders, and animals a

• Do not handle or operate a chain saw

• Carefullyplanyoursawingoperation inad-

OPERATE YOUR SAW SAFELY

• Do not operate a chain saw with one hand.

• Operate the chain saw only in a welt-venti-

• Do not operate saw from a ladder or in a

• Make sure the chain will not make contact

the engine starts.

ging, vented goggles or face screen; an approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your hearing, Regular users should have hear-

ing checked regularly as chain saw noise can damage hearing. Secure hair above

shoulder length.

chain when the engine is running. minimum of 30 feet (10 meters) away from

the work area. Do not allow other people or animals to be near the chain saw when

starting or operating the chain saw,

when you are fatigued, ill, or upset, or if you have taken alcohol, drugs, or medication.

You must be in good physical condition and mentally alert. Chain saw work is

strenuous, if you have any condition that might be aggravated by strenuous work,

check with your doctor before operating a chain saw,

vance. Do not start cutting until you have a ciear work area, secure footing, and, if you

are felling trees, a planned retreat path,

Serious injury to the operator, helpers, by- standers or any combination of these per-

sons may result from one-handed opera- tion. A chain saw is intended for

two-handed use,

lated outdoor area,

tree,

with any object while starting the engine. Never try to start the saw when the guide bar is in a cut.

• Donotputpressureonthesawattheend

ofthecut.Applyingpressurecancause youtolosecontrolwhenthecutiscom-

pleted.

• Stoptheenginebeforesettingthesaw

down.

• Donotoperateachainsawthatisdam- aged,improperlyadjusted,ornotcom-

pieteiyandsecurelyassembled.Always replacebar,chain,handguard,orchain

brakeimmediatelyifitbecomesdamaged,

brokenorisotherwiseremoved.

• Withtheenginestopped,handcarrythe

chainsawwiththemufflerawayfromyour

body,andtheguidebarandchaintothe rear,preferablycoveredwithascabbard.

MAINTAINYOURSAWINGOOD WORKINGORDER

• Havea_lchainsawserviceperformedbya

qualifiedservicedealerwiththeexception

oftheitemslistedinthemaintenancesec- tionofthismanual.Forexample,ifimprop-

ertootsareusedtoremoveorholdthefly- wheelwhenservicingtheclutch,structural

damagetotheflywheelcanoccurand

causetheflywheeltoburst.

• Makecertainthesawchainstopsmoving

whenthethrottletriggerisreleased.For

correction,refertoCARBURETORAD-

JUSTMENTS.

• Nevermodifyyoursawinanyway.

• Keepthehandlesdry,clean,andfreeofoil

orfuelmixture.

• Keepfuelandoilcaps,screws,andfas-

tenerssecurelytightened.

• UseonlyHusqvarna_)accessoriesand replacementpartsasrecommended.

HANDLE FUEL WITH CAUTION

• Do not smoke while handling fuel or while operating the saw.

• Eliminate all sources of sparks or flame in the areas where fuel is mixed or poured.

There should be no smoking, open flames, or work that could cause sparks. Allow en-

gine to coot before refueling.

• Mix and pour fuel in an outdoor area on bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved, marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

• Move at least 10 feet (3 meters) from fueF ing site before starting engine.

• Turn the engine off and let saw cool in a non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap and refuel unit.

• Store the unit and fuel in an area where fuel vapors cannot reach sparks or open

flames from water heaters, electric motors or switches, furnaces, etc.

KICKBACK

_WARNING: Avoid kickback which

can result in serious injury. Kickback is the backward, upward or sudden forward motion

of the guide bar occurring when the saw chain near the upper tip ofthe guide bar con-

tacts any object such as a log or branch, or

when the wood closes in and pinches the saw chain in the cut. Contacting a foreign ob-

ject in the wood can also result in loss of chain saw control

• Rotational Kickback can occur when the moving chain contacts an object at the up-

per tip of the guide bar. This contact can cause the chain to dig into the object,

which stops the chain for an instant. The result is a lightning fast, reverse reaction

which kicks the guide bar up and back to- ward the operator.

• Pinch-Kickback can occur when the the wood closes in and pinches the moving

saw chain in the cut along the top of the guide bar and the saw chain is suddenly

stopped. This sudden stopping of the chain results in a reversal of the chain force used to cut wood and causes the

saw to move in the opposite direction of the chain rotation. The saw is driven straight

back toward the operator.

• Pull-In can occur when the moving chain contacts a foreign object in the wood in the

cut along the bottom of the guide bar and the saw chain is suddenly stopped. This

sudden stopping pulis the saw forward and away from the operator and could easily cause the operator to lose control of the

saw.

Avoid Pinch-Kickback:

• Be extremely aware of situations or ob- structions that can cause material to pinch

the top of or otherwise stop the chain,

• Do not cut more than one log at a time.

• Do not twist the saw as the bar is with- drawn from an undercut when bucking.

Avoid Pull-In:

• Always begin cutting with the engine at full speed and the saw housing against wood.

• Use wedges made of piastic or wood. Never use metal to hold the cut open.

Kickback Path

Avoid Obstructions

ClearThe Working Area

REDUCE THE CHANCE OF KICKBACK

• Recognize that kickback can happen. With a basic understanding of kickback,

you can reduce the element of surprise which contributes to accidents.

• Never let the moving chain contact any ob-

ject at the tip of the guide bar.

• Keep the working area free from obstruc- tions such as other trees, branches, rocks,

fences,stumps,etc.Eliminateoravoid

anyobstructionthatyoursawchaincould hitwhileyouarecuttingthroughaparticu-

larlogorbranch.

• Keep your saw chain sharp and properly tensioned. A loose or dull chain can in-

crease the chance of kickback occurring, Follow manufacturer's chain sharpening

and maintenance instructions. Check ten- sion at regular intervals with the engine

stopped, never with the engine running. Make sure the chain brake nuts are se-

curely tightened after tensioning the chain.

• Beginandcontinuecuttingatfullspeed. If the chain is moving at a slower speed,

there is greater chance of kickback occur- ring.

• Cut one log at a time,

• Use extreme caution when re-entering a previous cut.

• Do not attempt cuts starting with the tip of the bar (plunge cuts),

• Watch for shifting logs or other forces that could close a cut and pinch or fall into chain,

• Use the Reduced-Kickback Guide Bar and Low-Kickback Chain specified for

your saw,

MAINTAIN CONTROL

Stand to the left of

the saw

Never reverse hand positions

• Stand with your weight evenly balanced on both feet,

• Stand slightly to the left side of the saw to keep your body from being in a direct line with the cutting chain,

• Do not overreach. You could be drawn or thrown off balance and lose control of the

saw.

• Do not cut above shoulder height. It is diffi- cult to maintain control of saw above

shoulder height.

KICKBACK SAFETY FEATURES

_bWARNING: The following features

are included on your saw to help reduce the hazard of kickback; however, such features

will not totally eliminate this dangerous reac- tion. As a chain saw user, de not rely only on

safety devices. You must follow all safety precautions, instructions, and maintenance

in this manual to help avoid kickback and other forces which can result in serious

injury,

• Reduced-Kickback Guide Bar, designed with a small radius tip which reduces the

size of the kickback danger zone on the bar tip, A Reduced- Kickback Guide Bar

has been demonstrated to significantly re- duce the number and seriousness of kick-

backs when tested in accordance with safety requirements for gasoline powered

chain saws as set by ANSI B175.1.

Reduced Kickback Symmetrical Guide Bar

_mall Radius Tip

_ Elbow locked

-'_-_o on underside of handlebar

• Keep a good, firm grip on the saw with both hands when the engine is running and don't let go. A firm grip will help you reduce kickback and maintain control of the saw.

Keep the fingers of your left hand encir- cling and your left thumb under the front

handlebar. Keep your right hand com- pletely around the rear handle whether

your are right handed or left handed. Keep your left arm straight with the elbow

locked,

• Position your left hand on the front handle- bar so it is in a straight line with your right

hand on the rear handle when making bucking cuts. Never reverse right and left

hand positions for any type of cutting,

Symmetrical Guide Bar _ "_,_,

• Low-Kickback Chain, designed with a contoured depth gauge and guard link which deflect kickback force and allow

wood to gradually ride into the cutter. Low-Kickback Chain has met kickback

performance requirements when tested on a representative sample of chain saws

below 3,8 cubic inch displacement speci- fied in ANSI B175.1.

Contoured Depth Gauge

Low-Kickback _ and allows wood

Chain to gradually ride

L'-'_,_%wl_Can Obstruct Material

Not a Low-Kickback Chain

Large Radius Tip

D Elongated Guard Link

into cutter

• Front Hand Guard, designed to reduce the chance of your left hand contacting the chain

if your hand slips off the front handlebar.

• Position of front and rear handlebars, de- signed with distance between handles and "in-line" with each other. The spread and

"in-line" position of the hands provided by this design work together to give balance

and resistance in controlling the pivot of the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE AND CKA ANGLE

• Chain Brake, designed to stop the chain in the event of kickback.

_i_WARNING: WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WILL

PROTECT YOU IN THE EVENT OF A KICKBACK. Kickback is a lightning fast ac-

tion which throws the bar and rotating chain back and up toward the operator. Kickback

can be caused by allowing contact of the bar tip in the danger zone with any hard object.

Kickback can also be caused by pinching the saw chain along the top of the guide bar. This action may push the guide bar rapidly back

toward the operator. Either of these events may cause you to lose control of the saw

which could result in serious injury or even death. DO NOT RELY UPON ANY OF THE

DEVICES BUILT INTO YOUR SAW. YOU SHOULD USE TH E SAW PROPERLY AND

CAREFULLY TO AVOID KICKBACK. Re- duced-kickback guide bars and low-kick-

back saw chains reduce the chance and magnitude of kickback and are recom-

mended. Your saw has a low kickback chain and bar as original equipment. Repairs on a chain brake shoutd be made by an autho-

rized servicing dealer. Take your unit to the Computed kickback angle (CKA) Table

BAR

MODEL

137 142 137 142

137 142 137 142 142

NOTE: If this saw isto be used for commer- cial logging, a chain brake is required and

shall not be removed or otherwise disabled to compty with Federat OSHA Regulations

for Commercial Logging. Contact your au- thorized Husqvarna service dealer. SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

Type Length CHAIN TYPE

0.050 GA 14" 91VG- 52

0.043 GA 14" 90SG- 52

0.050 GA 16" 91VG- 56

0.043 GA 16" 90SG- 56

0.050 GA 18" 91VG- 62

place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized

Husqvarna® service dealer.

• Tip contact in some cases may cause a light- ning fast reverse REACTION, kicking the

guide bar up and back toward the operator.

• Pinching the saw chain along the top of the guide bar may push the guide bar rapidly

back toward the operator.

• Either of these reactions may cause you to _ose contro_ of the saw which could result

in serious injury. Do not rely upon the safe- ty devices built into your saw.

_, WARNING: Computed kickback

angle (CKA) listed on your saw and listed in the CKA table below represents angle of kickback your bar and chain combinations will have

when tested in accordance with CSA (Cana- dian Standards Association) and ANSI stan-

dards. When purchasing replacement bar and chain, considerations should be given to the

lower CKA values, Lower CKA values repre- sent safer angles to the user, higher values in-

dicate more angle and higher kick energies. Computed angles represented indicate total energy and angle associated without activation

of the chain brake during kickback, Activated angle represents chain stopping time relative to activation angle of chain break and resulting

kick angle of saw, in all cases lower CKA val- ues represent a safer operating environment for the user.

The following guide bar and chain combina- tions meet kickback requirements of CSA

Standards Z62,1, Z62,3, & ANSI B175.1 when used on saws listed in this manual.

Use of bar and chain combinations other than those listed is not recommended and

may not meet the CKA requirements per standard.

CKA WITHOUT

CHAIN BRAKE

25" 25" 25" 25" 25" 25"

25" 25" 25"

damage in the fingers, hands, and joints of people prone to circulation disorders or

abnormal swellings. Prolonged use in cold weather has been linked to blood vessel

damage in otherwise healthy people. If symptoms occur such as numbness, pain,

loss of strength, change in skin color or texture, or loss of feeling inthe fingers, hands, or joints,

discontinue the use of this tool and seek

medicalattention.Ananti-vibrationsystem

doesnotguaranteetheavoidanceofthese problems.Userswhooperatepowertoolson

acontinualandregularbasismustmonitor

closelytheirphysicalconditionandthe

conditionofthistool. SPECIALNOTICE: Your saw is equipped

with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and

4443. All U.S. forest land and the states of California, Idaho, Mah_e, Mh_nesota, New Jersey, Oregon, and Washington require by

law that many internal combustion engines to be equipped with a spark arresting screen.

If you operate a chain saw in a state or locale where such regulations exist, you are legally

responsible for maintaining the operating condition of these parts. Failure to do so is

a violation of the law. Refer to the SERVICE section for maintenance of the spark arresting screen. Failure to follow all Safety Rutes and

Precautions can result in serious injury. If situations occur which are not covered in this

manual, use care and good judgement. If you need assistance, contact your authorized

Husqvarna service dealer. STANDARDS: This saw is listed by Underwriter's Laboratories, Inc., in

accordance with: ANSI B175.1-2000 American National

Standards for Gasoline-Powered Chain Saws - Safety Requirements

CBA Z62.1-1995 Chah_ Saws Occupational Health and Safety CSA Z62.3=1gg6 Chain Saw Kickback Occupational Health and Safety

Protective gloves (not provided) should be

worn during assembly. ATTACHING THE BAR & CHAIN (If

not already attached) ,_i_WARNING: Recheck each assem-

bly step if the saw is received assembled. Al- ways wear gloves when handling the chain.

The chain is sharp and can cut you even when it is not moving!

1. Loosen and remove the chain brake nuts and the chain brake from the saw.

2. Remove the plastic shipping spacer (if present).

Location of shipping spacer

Chain Brake

3. An adjusting pin and screw is used to ad-

just the tension of the chain. It is very im-

portant when assembling the bar. that

the pin tocated on the adjusting screw aligns into a hole in the bar. Turning the screw will move the adjustment pin up

and down the screw. Locate this adjust-

ment before you begin mounting the bar

onto the saw. See illustration.

Nuts

Bar Tool

Inside view of

4. Turn the adjusting screw by hand coun- terctockwise until the adjusting pin just

touches the stop. This should allow the pin to be near the correct position. Fur-

ther adjustment may be necessary as you mount the bar.

5. Slide guide bar behind clutch drum until guide bar stops against clutch drum

sprocket.

Mount the Bar

6. Prepare the chain by checking the proper direction. Without following the illustration it

is easy to place the chain on the saw in the wrong direction. Use the illustration of the

chain to determine the proper direction.

_ ip of

Bar

DIIRECTION OF ROTATION

Cutters Depth Gauge

._._C hain Brake

ft _ _ '\

Adjustment located on Chain Brake

Drive Links /

7. Place chain over and behind clutch, fit- ting the drive links in the clutch drum sprocket.

Above_acadenaene_enaranaie

8. Fitbottomofdrivelinksbetweenthe teethinthesprocketinthenoseofthe guidebar.

9. Fitchaindrivelinksintobargroove.

10.Pullguidebarforwarduntilchainissnug inguidebargroove.Ensurealldrivelinks

areinthebargroove.

11.Now,installchainbrakemakingsurethe

adjustingpinispositionedinthelower

holeintheguidebar.Rememberthispin

movesthebarforwardandbackwardas

thescrewisturned.

12.Installchainbrakenutsandfingertighten

only.Oncethechainistensioned,you willneedtotightenchainbrakenuts.

CHAIN TENSION

(including units with chain already installed) NOTE: When adjusting chain tension,

make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can

cause damage.

Checking the tension:

Use the screwdriver end of the bar tool to move the chain around the bar. If the chain

does not rotate, it is too tight. If too loose, the chain will sag betow the bar.

Guide

Adjusting the tension:

Chah_ tension is very important. Chain stretches during use. This is especially true

during the first few times you use your saw. Always check chain tension each time you

use and refuel your saw. You can adjust the chain tension by loosen-

ing the chain brake nuts and turning the ad- justing screw t/4 of a turn while lifting up on

the bar.

• If chain is too tight, turn adjusflng screw 1/4 turn counterclockwise.

• If chain is too loose, turn adjusting screw 1/4 turn clockwise.

..-z:_.Lz Adjusting / //

Chain Brake Nuts Guide Bar

Adjusting Screw - 1/4 Turn

• Lift up the tip of the bar and tighten the chain brake nuts with the combination

screwdriver/wrench.

• Recheck chain tension.

._._e.Z.L . Chain Brake A _"

_ _ Nuts

_ Bar

/ Chain Adjustment

Chain Brake Nuts Tool (Bar Tool)

FUELING ENGINE

_, WARNIN G: Remove fuel cap slowly

when refueling. This engine is certified to operate on unleaded

gasoline. Before operation, gasoline should be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a

ratio of 40:1, (A 40:1 ratio is obtained by mixing

3.2 ounces of oil with 1 gaflon of unleaded gasoline). DO NOT USE automotive or boat

oil. These oils will cause engine damage. When mixing fuel follow the instructions printed

on the container, Always read and follow the safety rules listed under HANDLE FUELWITH

CAUTION,

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

£A

,_WARNING: If the saw is operated

with a Ioose chain, the chain could jump off the guide bar and result in serious injury.

filled. Lack of oil will quickly ruin the bar and chain. Too little oii will cause overheating

shown by smoke coming from the chain and/ or discoloration of the bar. In freezing weather oil will thicken, making it necessary to thin bar

and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene.

Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lu- brication.

Genuine Husqvama® bar and chain oil is rec- ommended to protect your unit against exces- sive wear from heat and friction. Husqvama® oil resists high temperature thinning.

if Husqvarna® bar oil is not available, use a good grade SAE 30 oil.

• Never use waste oil for bar and chain lu- brication.

• Always stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol-blended

fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during

storage. Acidic gas can damage the fuel system of an engine while in storage. To

WAR NIN G: The chain must not move

when the engine runs at idle speed. Ifthe chain moves at idle speed refer to CARBURETOR

ADJUSTMENTS within this manual Avoid contact with the muffler. A hot muffler can

cause serious bums. To stop the engine, move the ON/STOP switch to the STOP position. To start the engine, hold the saw firmly on the ground as illustrated below. Make sure

the chain is free to turn without contacting aey object.

Use only 15"- 18" of rope per pull.

Hold saw firmly while pulling starter rope.

Important points to remember When pulling tile starter rope. do not use the

full extent of the rope as this can cause the rope to break. Do not let starter rope snap

back. Hold the handle and let the rope rewind slowly. For cold weather starting, start the

unit at full choke; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/

fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or a warm engine after running out of

fuel)

NOTE: In the following steps, when tile ctlo-

ke/fast idle lever is pulled out to the full extent, the correct throfe setting for starting is set au-

tomatically.

1. Move ON/STOP switch to the ON position.

2. Pull the choke/fast idle lever out to the full extent (to the FULL CHOKE position).

3. Pull starter rope quickly with your right

hand a maximum of 5 times. Then, pro-

ceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

4. Push the choke/fast idle lever in to the

HALF CHOKE position.

5. Pull the starter rope quickly with your

right hand until the engine starts.

6. Allow the engine to run for approximately

30 seconds. Then, squeeze and release throttle trigger to allow engine to return to

idle speed.

avoid engine problems, the fuel system should be emptied before storage for 30

days or longer. Drain the gas tank, start the engine and let it run unti_ the fuel lines and carburetor are empty. Use fresh fuel next

season. See STORAGE section for addi- tionat information.

CHOKE/FAST IDLE LEVER

STARTING A WARM ENGINE:

1. Move ON/STOP switch to the ON position.

2. PulJ tile cheke/fast idle lever out te the

HALF CHOKE pesitien.

3. Pull the starter rope quickly with your right hand until the engine starts.

4. Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulis.

Flooded engines can be cleared of excess fuel by following the warm engine starting

procedure listed above. Ensure the ON/ STOP switch is in the ON position.

Starting could require pulling the starter rope handle many times depending on how badly

the unit is flooded. If engine fails to start refer to the TROUBLESHOOTING TABLE.

CHAIN BRAKE

_L, WARNING: If the brake band is worn

too thin it may break when tile chain brake is triggered. With a broken brake band, the chain

brake will not stop the chain, The chain brake should be replaced by an authorized service

dealer if any part is worn to less than 0,020" (0.5 mm) thick, Repairs on a chain brake

should be made by an authorized service deal- er. Take your unit to the place of purchase if purchased from a servicing dealer, or to the

nearest authorized Husqvarna service dealer,

• This saw is equipped with a chain brake.

The brake is designed to stop the chain if kickback occurs.

• Theinertia-activatedchainbrakeis activatedifthefronthandguardispushed forward,eithermanually(byhand)or

automatically(bysuddenmovement).

• If thebrakeis alreadyactivated,it is disengagedbypullingthefronthandguard

backtowardthefronthandleasfaras possible,

• Whencuttingwiththesaw,thechainbrake mustbedisengaged.

Disengaged

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine

must be running when performing this proce- dure. This is the only instance when the saw

should be placed on the ground with the en- gine running.

Place the saw on firm ground. Hold the han- dles with both hands and apply full throttle.

Activate the chain brake by turning your left wrist against the hand guard without releas-

ing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

_IIWARNING: When performh3g the

followh_g procedure, the engine must be turned off.

Hold the chain saw approximately 14" (35 cm) above a stump or other wooden surface.

Release your grip on the front handle and use the weight of the saw to let the top of the

guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the

brake shouid activate.

IMPORTANT POINTS

• Check chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

• Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

• Stop the saw if the chain strikes a foreign object. Inspect the saw and repair parts as

necessary.

• Keepthe chain outofdirtand sand. Evena small amount of dirt will quickly dull a chain

and increase the possibility of kickback.

• Practice cutting a few small logs using the following techniques to get the "feel" of us-

ing your saw before you begin a major sawing operation.

• Squeeze the throttIe trigger and allow

the engine to reach full speed before cut- ting.

• Begin cutting with the saw frame against

the log.

• Keep the engine at full speed the entire

time you are cutting.

• AIIowthechaintocutforyou. Exert only

light downward pressure.

• Release the throttle trigger as soon as

the cut is completed, allowing the engine to idle. If you run the saw at full throttle

without a cutting load, unnecessary wear can occur to the chain, bar, and en-

gine. It is recommended that the en- gine not be operated for longer than

30 seconds at full throttle.

• To avoid losing control when cut is com-

plete, do not put pressure on saw at end

of cut.

• Stop the engine before setting the saw down,

TREE FELLING TECHNIQUES

_WARNING: Check for broken or

dead branches which can fall while cutting

causing serious injury. Do not cut near build- ings or electrical wires if you do not know the

direction of tree fall, nor cut at night since you will not be able to see well, nor during bad

weather such as rain, snow, or strong winds, etc. If thetree makes contact with any utility line, the utility company should be notified

immediately.

• Carefullyplanyoursawingoperation inad-

vance.

• Cleartheworkarea. You needacleararea all around the tree so you can have secure

footing.

• The chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

• Study the natural conditions that can cause the tree to fall in a particular direc-

tion.

Natural conditions that can cause a tree to fall in a particular direction include:

• The wind direction and speed.

• The lean of the tree. The lean of a tree might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de- termine the direction of tree lean.

• Weight and branches on one side.

• Surrounding trees and obstacles.

Look for decay and rot. If thetrunk is rotted, it can snap and fall toward the operator. Check for broken or dead branches which

can fall on you while cutting. Make sure there is enough room for the tree

to fall Maintain a distance of 2-1/2 tree lengths from the nearest person or other ob-

jects. Engine noise can drown out a warning call

Remove dirt, stones, loose bark, nails, sta- ples, and wire from the tree where cuts are to

be made. Plan a clear retreat path to the rear and diag-

onal to the line of fall.

_. x2 Plan a clear retreat path

()--_- Direction of Fall

45 ° /

y/_.€¢"

FELLING LARGE TREES

(6 h_ches/15 cm in diameter or larger) The notch method is used to fell large trees. A notch is cut on the side of the tree in the de-

sired direction of fall. After a felling cut is made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTE: If the tree has large buttress roots, remove them before maMng the notch. Ifus- ing saw to remove buttress roots, keep saw

chain from contacting ground to prevent dull- ing of the chain.

NOTCH CUT AND FELLING THE TREE

• Make notch cut by cutting the top of the

notch first. Cut through 1/3 of the diameter of the tree. Next complete the notch by cut- ting the bottom of the notch. See illustra- tion. Once the notch is cut remove the notch of wood from the tree.

• After removing the wood from the notch,

make the felling cut on the opposite side of the notch. This is done by making a cut about

two inches higher than the center of the notch. This will leave enough uncut wood between the felling cut and the notch to form

a hinge. This hinge will help prevent the tree from falling in the wrong direction.

NOTE: Before felling cut is complete, use wedges to open the cut when necessary to

control the direction of fall. To avoid kickback and chain damage, use wood or plastic

wedges, but never steel or iron wedges.

• Be alert to signs that the tree is ready to fall cracking sounds, widening of the fell- ing cut, or movement in the upper branches.

• As tree starts to fall, stop saw, put it down, and get away quickly on your planned re-

treat path.

• DO NOT cut down a partialty fallen tree with your saw. Be extremely cautious with

partially fallen trees that may be poorly supported. When a tree doesn't fall com-

pletely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen tree to the desired log length.

_lJ WARNING : Do not stand on the log being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill of the log being cut.

IMPORTANT POINTS

• Cut only one log at a time.

• Cut shattered wood very carefully; sharp pieces of wood could be flung toward oper- ator.

• Use a sawhorse to cut small logs. Never allow another person to hold the log while

cutting and never hold the tog with your leg or foot.

• Do not cut in an area where logs, limbs, and roots are tangled. Drag the logs into a

clear area before cutting by pulling out ex- posed and cleared logs first.

TYPES OF CUTTING USED FOR BUCKING

_WARNING: If saw becomes

pinched or hung in a log, don't try to force it out. You can tose control ofthe saw resulting

in injury and/or damage to the saw. Stop the saw, drive a wedge of plastic or wood into the

cut until the saw can be removed easily. Re- start the saw and carefully reenter the cut.

Do not attempt to restart your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Hinge holds tree on stump and helps

control fall

_.,"4, ' out

of - ",,_i 'l i\

notch .z/-r,,__ _,_

Turn saw OFF and use a plastic or wooden wedge to force cut open.

Overcutting begins on the top side of the log with the saw against the log. When overcut-

ting use light downward pressure.

Overcutting Undercutting

,_ 1st Cut

Undercutting involves cutting on the under- side of the log with top of saw against the log.

When undercutth_g use light upward pres- sure. Hold saw firmly and maintain control

The saw will tend to push back toward you.

_.WARNING: Never turn saw upside down to undercut. The saw cannot be con- trolled in this position. Always make your first cut on the compres-

sion side ofthe tog. The compression sMe of the log is where the pressure of the log's

weight is concentrated.

First cut on comtaression side of log

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

• Overcut through 1/3 of the diameter of the log=

• Roll the log over and finish with a second overout.

• Watch for logs with a compression side to prevent the saw from pinching. See illustra-

tion for cutting logs with a compression side.

BUCKING USING A LOG OR

SUPPORT STAND

• Remember your first cut is always on the compressions side ofthe log. (Refer tothe

illustration below for your first and second cuts).

• Your first cut should extend 1/3 of the diameter of the log.

• Finish with your second cut.

Using a log for support 2nd Cut

Using a support stand

1st Cut

LIMBING AND PRUNING

_L, WARNING: Be aiert for and guard

against kickback. Do not allow the moving chain to contact any other branches or objects

at the nose of the guide bar when limbing or pruning. Allowing such contact can result in

serious injury.

_,WARNING: Never climb into atree

to limb or prune. Do not stand on ladders, platforms, a log. or inany position which can

cause you to lose your balance or control of the saw.

IMPORTANT POINTS

• Work slowly, keeping both hands firmly gripped on the saw. Maintain secure foot-

ing and balance.

• Watch out for springpotes. Springpoles are small size limbs which can catch the

saw chain and whip toward you or pull you off balance. Use extreme caution when

cutting small size limbs.

• Be alert for springback. Watch out for branches that are bent or under pressure.

Avoid being struck by the branch or the saw when the tension in the wood fibers is

released.

• Keep a clear work area. Frequently clear branches out of the way to avoid tripping

over them.

LIMBING

• Always limbatreeafter itis cutdown. Only then can limbing be done safely and prop-

erly.

• Leave the larger limbs underneath the felled tree to support the tree as you work.

• Start at the base of the felled tree and work toward the top, cutting branches and

limbs. Remove small limbs with one cut.

• Keep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

• Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

• Always use an overcut to cut small and freely hanging limbs. Undercutting could

cause _imbs to fali and pinch the saw.

PRUNING

_WARNING: Limit pruning to limbs

shoulder height or below. Do not cut if branches are higher than your shoulder. Get

a professional to do the job.

• Make your fist cut I/3 of the way through the bottom of the limb.

• Next make a 2nd cut all the way through the limb. Then cut a third over-

cut leaving a 1 to 2 inch cellar from the

trunk of the tree.

l i _'i Secon¢c_u_

ThirdaiUt .,_'_

_l C°_/Ir#_1"" Firsteut _1 [ Pruning technique

z't

ABkWARNING: Muffler is very hot dur-

ing and after use. Do net touch the muffler or allow combustible material such as dry

grass or fuel to do so. We recommend all service and adjustments

not listed in this manual be performed by an authorized Husqvarna Service Dealer.

MAINTENANCE SCHEDULE

Check:

FueI mixture level .... Before each use

Bar lubrication ....... Before each use

Chain tension ....... Before each use

Chain sharpness .... Before each use

For damaged parts .. Before each use

For loose caps ...... Before each use

For loose fasteners... Before each use

For loose parts ...... Before each use

Muffler ............. Every 25 hours*

Inspect and Clean:

Bar ................ Before each use

Complete saw ....... After each use

Air filter ............. Every 5 hours*

Chain brake ........ Every 5 hours*

Replace spark plug . Yearly Replace fuel filter... Yearly

* Hours of Operation

AIR FILTER

CAUTION: Do not clean filter in gasoline or other flammable soivent to avoid creating a

fire hazard or producing harmful evaporative emissions.

Cleaning the air filter: A dirty air filter decreases engine perform-

ance and increases fuel consumption and harmful emissions. Always clean after 15 tanks of fuel or 5 hours of operation, which-

ever comes first. Clean more frequently in dusty conditions. A used air filter can never be completely cleaned. It is advisable to re-

place your air filter with a new one after every 50 hours of operation, or annually, whichever comes first.

1. Loosen 3 screws on cylinder cover.

2. Remove cylinder cover.

3. Remove air filter.

4. Clean the air filter using hot soapy water. Rinse with clean cool water. Air dry com-

pletely before reinstalling.

5. Reinstall air filter.

6. Reinstall cylinder cover and 3 screws. Tighten securely.

_i_ Air Filter

' _--_ _" _ Air Filter

_'=_]*'_J" "_" Screws

MUFFLER AND SPARK ARREST- ING SCREEN

A_, WARNING: The muffler on this prod-

uct contains chemicals known to the State of California to cause cancer.

NOTE: THE SPARK ARRESTING SCREEN ON THIS UNIT IS NOT SERVI-

CEABLE. For normal homeowner use, the muffler and

spark arresting screen will not require re- placement. After 75 hours of use, we recom-

mend that your muffler be replaced by your authorized Husqvarna service dealer.

CARBURETOR ADJUSTMENTS The chain will be moving during most of this

procedure. Wear your protective equipment and observe all safety precautions. The

chain must not move at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if

you notice any of the following conditions:

• Chain moves at idle. See iDLE SPEED-T

adjusting procedure.

• Saw will not idle. See IDLE SPEED-T ad-

justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow.

Adjustspeeduntilenginerunswithoutchain

movement(idletoofast)orstalling(idletoo stow).

• Turnidlespeedscrew(T)clockwisetoin-

creaseenginespeed.

• Turnidlespeedscrew(T)counterclock-

wisetodecreaseenginespeed.Ifyoure-

quirefurtherassistanceorareunsureabout performingthisprocedure,contactyourau-

thorizedservicedealer,

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper amount of bar lubrication it may be neces-

sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust

from the guide bar and sprocket hole. To maintain guide bar:

• Move ON/STOP switch to the STOP posi- tion.

• Loosen and remove chain brake nuts and chain brake. Remove bar and chain from

saw.

• Clean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From _ 1_

Guide Bang roov__ _'_

_ Holes _, _''_

,.j..

• Burring of guide bar rails is a normal process of rail wear. Remove these burrs

with a fiat file.

• When rail top is uneven, use a flat file to re- store square edges and sides.

_(7_ File Rail Edges_ r] 17

I'1

Worn Groove Correct Groove

Replace guide bar when the groove is worn,

the guide bar is bent or cracked, or when exce- ss heating or burring of the rails occurs. If re-

placement is necessary, use only the guide bar specified for your saw in ti_e repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING Chah_ sharpening is a complicated task that

requires special tools. We recommended you refer chain sharpening to a professional

chain sharpener. IGNITION TIMING

Ignition timing is fixed and nonadjustable.

and Sides I U I

Square I I

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and

runs better.

1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Remove spark plug from cylinder and discard.

5. Replace with Champion RCJ-7Y spark plug nd tighten securely with a 3/4 inch

(19 mm) socket wrench. Spark plug gap should be 0.025 inches (0.6 mm).

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3 screws. Tighten securely.

Spark Plug Boot

STORAGE

_bWARNING: Stop engine and allow to cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel in an area where fuel vapors cannot reach

sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

Store unitwith all guards in place. Position so that any sharp object cannot accidentally

cause injury to passersby. Store the unit out of reach of children.

• Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

• Clean the unit before storing. Pay particu-

lar attention to the air intake area, keeping it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

• Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an open flame from hot water heaters, electric motors or switches, furnaces, etc.

• Store in a dry area out of the reach of chil-

dren.

CAUTION: It is important to prevent gum deposits from forming in essential fuel sys- tem parts such as the carburetor, fuel filter,

fuel hose, or fuel tank during storage. Alco- hol blended fuels (called gasohol or using

ethanol or methanol) can attract moisture which leads to fuel mixture separation and

formation of acids during storage. Acidic gas can damage the engine.

TROUBLESHOOTING TABLE

_b, WARNING: Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit,

TROUBLE REMEDY

Engine will not start or will run

only a few seconds after

starting.

Engine will 1. Carburetor requires not idle adjustment. properly. 2. Crankshaft seals worn.

Engine will not 1. Air filter dirty. 1. Clean or repIace air filter. accelerate, 2. Spark plug fouled. 2. Clean or replace plug and regap. lacks power. 3. Chain brake engaged. 3. Disengage chain brake.

or dies under 4. Carburetor requires 4. Contact an authorized service dealer. a load. adjustment.

Engine 1. Too much oil mixed with 1. Empty fuel tank and refill with smokes gasoline, correct fuel mixture.

excessively.

Chain moves 1. Idle speed requires 1. See "Carburetor Adjustment" in the at idle speed, adjustment. Service and Adjustments Section.

CAUSE

1. ignition switch off,

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. FueI not reaching carburetor.

2. Clutch requires repair. 2. Contact an authorized service dealer.

1. Move ignition switch to ON.

2. See "Difficult Starting" in Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace. Check for kinked or split fuel line;

repair or replace.

1. See "Carburetor Adjustment" in the Service and Adjustments Section.

2. Contact an authorized service dealer.

SECTION 1: LIMITED WARRANTY

Husqvarna Forest & Garden Company ("Husqvarna') warrants Husqvarna product

to the originaI purchaser to be free from defects in material and workmanship from the date of purchase for the "Warranty Period" of the prod- ucts as set forth below:

Lifetime Warranty: All tiller tines against

breakage, trimmer shafts, ignition coils and modules on hand held product.

3 Year Warranty: Spindles (on Zero Turn

Riders and Commercial Waik-Behinds),

2 Year COMMERCIAL Warranty: Husq- varna Commercial Turf Equipment - zero

turn riders, wide area walks, and ground en- gaging commercial equipment,

2 Year NON-COMMERCIAL Warranty: Au- tomatic mower, riding lawn mowers, yard and

garden tractors, walk behind mowers, tiliers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, hand held blowers, back-

pack blowers, hedge trimmers, electrical prod- ucts and power-assist collection systems for

non-commercial, non-professional, non-insti- tutional or non-income producing use, except

as herein stated_

Emission control system components neces-

sary to comply with CARB-TIER II and EPA regulations, except for those components

which are part of engine systems manufac- tured by third party engine manufacturers for

which the purchaser has received a separate

warranty with product information supplied at time of purchase. 1 Year Warranty: Power cutters, stump

grinder, pole pruners and pole saws for non- commercial, non-professional, non-institu-

tional or non - income producing use. AHtrim- mers. brushcutters, clearing saws, hovering

trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, and

power-assist collection systems used for commercial, institutional, professional, or in- come producing purposes or use.

Batteries have a one year prorated limited warranty with 100% replacement during the

first 6 months. 90 Day Warranty: Automatic mower, chain

saws, power cutters, stump grinders, pole saws, pole pruners, snow throwers, model se- ries 580 & 600 walk- behind mowers, and com-

mercial turf equipment or any Husqvama prod- uct used for commercial, institutional,

professional, or income producing purposes or use except as otherwise provided herein,

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer's origi-

nal purchase for defects in material and work- manship, NormaI wear, tear or abuse is not

covered under warranty, Product must be re- turned to Charlotte with a warranty claim form.

All care and maintenance instructions must be followed as stated by the manufacturer on the

care label. The fit of the protective apparel/boot is not covered under warranty.

30 Day Warranty: Replacement parts, ac- cessories including bars and chains, tools and

display items. SECTION 2: HUSQVARNA'S OB-

LIGATIONS UNDER THE WARRANTY

Husqvama will repair or replace defective com- bonents without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this

warranty:

(1)Normal customer maintenance items

which become worn through normal reg-

ular use, including, but not limited to,

belts, blades, blade adapters, bulbs, fil- ters, guide bars, lubricants, rewind springs, saw chains, spark plugs, starter

ropes and tines;

(2) Natural discoloration of material due to ul-

traviolet light.

(3) Engine and drive systems not manufac-

tured by Husqvarna; these items are cov- ered by the respective manufacturer's

warranty as provided in writing with the

product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer.

(4) Lawn and garden attachments are cov-

ered by a third party which gives a war-

ranty; all claims for warranty should be sent to the manufacturer; and

(5) Emission control system components

necessary to comply with CARB-TIER II and EPA regulations which are manufac-

tured by third party engine manufacturer.

SECTION 4: EXCEPTIONS AND

LIMITATIONS

This warranty shall be inapplicable to de- fects resulting from the following:

(1) Accident, abuse, misuse, negligence and

neglect, including stale fuel, dirt, abra- sives, moisture, rust, corrosion, or any

adverse reaction due to incorrect storage or use habits.

(2) Failure to operate or maintain the unit in ac-

cordance with the instruction manual or in- struction sheet furnished by Husqvarna.

(3) Alterations or modifications that change

the intended use of the product or affects the product's performance, operation, safety, or durability, or causes the product

to fail to comply with any applicable laws.

(4)Additional damage to parts or compo-

nents due to continued use occurring af- ter any of the above.

REPAIR OR REPLACEMENT AS PRO-

VIDED UNDER THIS WARRANTY IS THE

EXCLUSIVE REMEDY OF THE PUR-

CHASER. HUSQVARNA SHALL NOT BE

LIABLE FOR ANY INCIDENTAL OR CON- SEQUENTIAL DAMAGES FOR BREACH

OF ANY EXPRESS OR IMPLIED WAR- RANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BYAPPLI- CABLE LAW. ANY IMPLIED WARRANTY

OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON

THESE PRODUCTS IS LIMITED IN DURA- TION TO THE WARRANTY PERIOD AS

DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RESERVES

THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITH-

OUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.

Some states do not allow the exclusion of inci- dental or consequential damages, or limitations on how long an implied warranty lasts, so the

above limitations or exclusions may not apply to you. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RE- SPONSIBILITIES

The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section

of the Owner's/Operator's manual. Should an operational problem or failure occur, the prod- uct should not be used, but delivered as is to an

authorized Husqvama dealer for evaluation. Proof of purchase, as explained in Section 6,

rests solely with the customer.

SECTION 6: PROCEDURE TO OB- TAIN WARRANTY CONSIDERATION

It is the Owner's and Dealer's responsibility to make certain that the Warranty Registra-

tion Card is properly filled out and mailed to Husqvarna Forest & Garden Company. This

card should be mailed within ten (10) days from the date of purchase in order to confirm

the warranty and to facilitate post-sale ser- vice.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to ob-

tain warranty service. This proof must in- clude date purchased, modeI number, serial

number, and complete name and address of the selling dealer. To obtain the benefit of this warranty, the product believed to be defective must be de-

livered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days

from date of the operational problem or fail- ure. The product must be delivered at the

owner's expense. Pick-up and delivery charges are not covered by this warranty.

An authorized Husqvarna dealer can be nor- mally located through the "YeIIow Pages" of the local telephone directory or by calling

1-800-HUSKY62 for a dealer in your area.

Husqvarna

7349 Statesville Road

CHARLOTTE, NC 28269

YOUR WARRANTY RIGHTS AND OB-

LIGATIONS: The U.S. Environmental Protec-

tion Agency, California Air Resources Board,

Environment Canada and HUSQVARNA are pleased to explain the emissions control sys- tem warranty on your year 2005 and later small

off-road engine. In California, all small off-road engines must be designed, built, and equipped

to meet the State's stringent anti-smog stan- dards. HUSQVARNA must warrant the emis-

sion controi system on your small off-road en- gine for the periods of time listed below

provided there has been no abuse, neglect, or improper maintenance of your small off-road engine. Your emission control system in-

cludes parts such as the carburetor and the ignition system. Where a warrantable condi-

tion exists, HUSQVARNA will repair your small off-road engine engine at no cost to

you. Expenses covered under warranty in- clude diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COV- ERAGE: If any emissions related part on

your engine (as listed under Emissions Con- trol Warranty Parts List) is defective or a de-

fect in the materials or workmanship of the engine causes the failure of such an emis-

sion related part, the part will be repaired or replaced by HUSQVARNA. OWNER'S

WARRANTY RESPONSIBILITIES: As the small off-road engine engine owner, you are

responsible for the performance of the re- quired maintenance listed in your instruction

manual. HUSQVARNA recommends that you retain all receipts covering maintenance

on your small off-road engine, but HUSQ- VARNA cannot deny warranty solely for the

lack of receipts or for your failure to ensure the performance of all scheduled mainte-

nance, As the small off- road engine engine owner, you should be aware that HUSQ-

VARNA may deny you warranty coverage if your small off-road engine engine ora part of it has failed due to abuse, neglect, improper

maintenance, unapproved modifications, or the use of parts not made or approved by the

original equipment manufacturer. You are responsible for presenting your small off- road engine to a HUSQVARNA authorized

repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30

days. If you have any questions regarding your warranty rights and responsibilities,

you should contact your nearest authorized service center or call HUSQVARNA at

1-800-487-5962. WARRANTY COM- MENCEMENT DATE: The warranty period

begins on the date the small off-road engine is purchased. LENGTH OF COVERAGE:

This warranty shall be for a period of two years from the initial date of purchase.

WHAT IS COVERED: REPAIR OR RE- PLACEMENT OF PARTS, Repair or re- placement of any warranted part will be per-

formed at no charge to the owner at an approved HUSQVARNA servicing center. If

you have any questions regarding your war- ranty rights and responsibilities, you should

contact your nearest authorized service center or call HUSQVARNA at

1-800-487-5962. WARRANTY PERIOD:

Any warranted part which is not scheduled for replacement as required maintenance, or

which is scheduled only for regular inspec- tion to the effect of "repair or replace as nec- essary" shall be warranted for 2 years. Any

warranted part which is scheduled for re- placement as required maintenance shall be

warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS: The owner shall not be charged for diagnostic labor which leads to

the determination that a warranted part is de- fective if the diagnostic work is performed at an approved HUSQVARNA servicing cen- ter, CONSEQUENTIAL DAMAGES:

HUSQVARNA may be liable for damages to other engine components caused by the fail-

ure of a warranted part still under warranty. WHAT IS NOT COVERED: All failures

caused by abuse, neglect, or improper main- tenance are not covered, ADD-ON OR MO-

DIFIED PARTS: The use of add-on or modi- fied parts can be grounds for disallowing a

warranty claim. HUSQVARNA is not liable to cover failures of warranted parts caused by

the use of add-on or modified parts, HOW TO FILE A CLAIM: if you have any ques-

tions regarding your warranty rights and re- sponsibilities, you should contact your near-

est authorized service center or call HUSQVARNA at 1-800-487-5962.

WHERE TO GET WARRANTY SERVICE: Warranty services or repairs shall be pro-

vided at all HUSQVARNA service centers. call: 1-800-487-5962. MAINTENANCE,

REPLACEMENT AND REPAIR OF EMIS- SION RELATED PARTS: Any HUSQVAR-

NA approved replacement part used in the performance of any warranty maintenance

or repair on emission related parts will be provided without charge to the owner if the

part is under warranty, EMISSION CON- TROL WARRANTY PARTS LIST: Carbure-

tor, Ignition System: Spark Plug (covered up to maintenance schedule), ignition Module,

Muffler including catalyst. MAINTENANCE STATEMENT: The owner is responsible for the performance of all required maintenance

as defined in the instruction manual,

+ 39 hidden pages