Husqvarna 1152450-26 User Manual

Operator′s manual

K3000

K3000 Wet

Please read the operator’s manual carefully and make sure you understand the

instructions before using the machine.

EEEEnnnngggglllliiiisssshh

KEY TO SYMBOLS

Symbols on the machine:

WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

• Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

This product is in accordance with applicable EC directives.

WARNING! Dust forms when cutting, which can cause injuries if inhaled. Use an approved breathing mask. Always provide for good ventilation.

Symbols in the operator’s manual:

Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

WARNING! Sparks from the cutting blade can cause ﬁre in combustible materials such as: petrol (gas), wood, dry grass etc.

WARNING! Kickbacks can be sudden, rapid and violent and can cause life threatening injuries. Read and understand the instructions in the manual before using the machine.

Environmental marking. Symbols on the product or its packaging indicate that this product cannot be handled as domestic waste. It must instead be submitted to an appropriate recycling station for the recovery of electrical and electronic equipment.

By ensuring that this product is taken care of correctly, you can help to counteract the potential negative impact on the environment and people that can otherwise result through the incorrect waste management of this product.

For more detailed information about recycling this product, contact your municipality, your domestic waste service or the shop from where you purchased the product.

Other symbols/decals on the machine refer to special certiﬁcation requirements for certain markets.

2 – English

Contents

KEY TO SYMBOLS

Symbols on the machine: ............................................. 2

Symbols in the operator’s manual: ............................... 2

CONTENTS

Contents ...................................................................... 3

WHAT IS WHAT?

What is what on the power cutter - K3000? ................. 4

WHAT IS WHAT?

What is what on the power cutter - K3000 Wet? .......... 5

SAFETY INSTRUCTIONS

Steps before using a new power cutter ........................ 6

Personal protective equipment ..................................... 6

SAFETY INSTRUCTIONS

General safety warnings .............................................. 7

Machine′s safety equipment ........................................ 9

Cutting blades .............................................................. 10

General working instructions ....................................... 12

ASSEMBLY

Assembly ..................................................................... 14

Fitting the cutting blade ................................................ 14

Guard for the blade ...................................................... 14

STARTING AND STOPPING

Before starting ............................................................. 15

MAINTENANCE

General ........................................................................ 16

Cleaning ....................................................................... 16

Electrical Feed ............................................................. 16

Replacing the carbon brushes ..................................... 16

Bevel gear .................................................................... 17

Checking the drive axle and ﬂange washers ............... 17

Checking water connection with ﬂow limiter ................ 17

Daily maintenance ....................................................... 17

TECHNICAL DATA

Cutting equipment ........................................................ 18

Recommended cable dimensions ................................ 18

EC-declaration of conformity ........................................ 19

English – 3

WHAT IS WHAT?

What is what on the power cutter - K3000?

1 Rear handle

2 Guard for the blade 14”

3 Cutting blade

4 Locking the axle

5 Front handle

6 Inspection covers

7 Power switch lock

8 Switch

9 Rating plate

10 Brush retainer

11 Carbon brushes

12 Guard for the blade 12” (Model version)

13 Connection for vacuum cleaner

14 Combination spanner

15 Operator′s manual

4 – English

WHAT IS WHAT?

What is what on the power cutter - K3000 Wet?

1 Rear handle

2 Guard for the blade

3 Water kit

4 Cutting blade

5 Locking the axle

6 Front handle

7 Inspection covers

8 Power switch lock

9 Switch

10 Water tap

11 Water connection with ﬂow limiter

12 Rating plate

13 Brush retainer

14 Carbon brushes

15 Ground fault circuit interrupter (not for GB)

16 Combination spanner

17 Operator′s manual

English – 5

SAFETY INSTRUCTIONS

Steps before using a new power cutter

• Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

• The machine is only designed for cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes.

• Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs.

WARNING! Under no circumstances should you modify the original design of the

machine without approval from the manufacturer. Always use original spare parts. Unauthorized modiﬁcations and/or accessories may lead to serious injury or death to the user or others.

WARNING! Use of products which cut, grind, drill, sand or shape material can generate

dust and vapors which may contain harmful chemicals. Know the nature of the material being worked on and wear appropriate dust mask or respirator protection.

Personal protective equipment

WARNING! You must use approved personal protective equipment whenever you use the

machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

• Protective helmet

• Hearing protection

• Protective goggles or a visor

• Breathing mask

• Heavy-duty, ﬁrm grip gloves.

WARNING! A power cutter is a dangerous tool if used carelessly or incorrectly and can

cause serious, even fatal injuries. It is extremely important that you read and understand the contents of this Operator’s Manual.

Husqvarna Construction Products has a policy of continuous product development. Husqvarna reserves the right to modify the design and appearance of products without prior notice and without further obligation introduce design modiﬁcations.

All information and all data in the Operator’s Manual were applicable at the time the Operator’s Manual was sent to print.

• Tight-ﬁtting, heavy-duty and comfortable clothing that permits full freedom of movement.

• Use leg-guards recommended for the material to be cut.

• Boots with steel toe-caps and non-slip sole.

• Always have a ﬁrst aid kit nearby.

6 – English

+ 14 hidden pages