Husky Conventional Owner's Manual

MODEL #6310

Recommended Installation, Maintenance

and Inspection Instructions

WARNING

3/4" x 3/4" Swivel • Safe-T-Break® Combo

This device separates at less than 225 lbf / 1,000.9 N pull force!
This device is designed for use at motor fuel dispensing facilities only!

6310

INSTALLATION INSTRUCTIONS

NOTE: Prior to installation, it shall be determined that such pull force will not damage the hose assembly or
dispensing device. The dispensing device must be securely bolted to the dispensing island.

1. Attach scale to where the Swivel • Safe-T-Break® Combo will be installed. Apply 225 lbf /
1,000.9 N pull force at various angles and check dispenser and hose for damage. Refer
to UL 567 for details. If no damage occurred, release pull and complete installation.

2. Install in the direction of the ow arrows on Safe-T-Break

3. Use pipe thread sealant (not teon tape) approved for gasoline on the male threads of
the hose section. Do not overtighten - refer to UL 567 for details.

4. Install the Swivel • Safe-T-Break® Combo at nozzle or between the hose sections at
dispenser. Verify that the whip hose is the correct length.

®

.

DO NOT OVERTIGHTEN. DO NOT WRENCH ACROSS COUPLING.

DO NOT INSTALL DIRECTLY TO THE DISPENSER.

IF SEPARATION OCCURS

• Shut off dispenser and relieve line pressure.

• Before Reconnecting the Safe-T-Break®:

▪ Inspect the entire dispensing system and Swivel • Safe-T-Break® Combo for damage.
▪ Conduct pull test for dispenser integrity (see step 1 of installation instructions above).
▪ Measure gap at swivel joint - if a credit card ts in the gap (0.03 in / 0.76 mm) do not

reinstall.

• After Reconnecting the Safe-T-Break®:

▪ Check reconnected Safe-T-Break® for proper engagement.
▪ Check Swivel for smooth rotation.
▪ Check for electrical conductivity.
▪ Check for leaks at Swivel • Safe-T-Break® Combo.
▪ Check for proper ow of fuel.

ONLY PROPERLY TRAINED PERSONNEL SHOULD RECONNECT SAFE-T-BREAKS®.

TESTING / MAINTENANCE / INSPECTION

Daily

• Check for leaks / stains.

• Check for damage.

• Check for smooth rotation of swivel.

Monthly

• Measure gap at swivel joint - a credit
card should not t in the gap (0.03 in /

0.76 mm).

• Check "remove by" date.

Annually

• Check for electrical conductivity.

• Conduct pull test - disconnect Safe­T-Break®, inspect interior for debris,
discoloration, and foreign matter.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

009191-2 3/2009

• All drive aways, maintenance and
inspection activities must be logged
using the serial number of the individual
product.

• Apply city, state, or federal testing
regulations as appropriate.

ANY TEST / INSPECTION FAILURE

REQUIRES IMMEDIATE EQUIPMENT

REPLACEMENT OR REMOVAL FROM

SERVICE.

MADE IN THE USA

ALWAYS ADHERE TO INSTALLATION / USAGE INSTRUCTIONS AND WARNINGS.

Improper use may result in injury, damage, or hazardous spill.

GENERAL WARNINGS / INSTRUCTIONS

• Use of equipment is at individuals’ own risk.

• Always abide and adhere to city, state, and

federal regulations regarding use and

installation of dispensing equipment.

• Always follow the dispenser manufacturer’s

instructions.

• Always turn off all power to dispenser

during maintenance and inspection activities.

• Always close the shear valves during

maintenance and inspection activities.

• Always relieve pressure from system prior

to performing maintenance activities.

• Always check continuity after installation

using a megohmeter (Refer to PEI RP 400

for details).

• Always replace or remove from service

damaged or leaking dispensing equipment

immediately.

• Always report leaks / spills / accidents

to appropriate authorities.

• Always wear appropriate safety equipment

during maintenance activities.

• Always have appropriate re extinguishing

equipment within 5 ft / 1.5 m of dispensers.

• Always use pipe sealant approved for

gasoline service.

• Always place containers on the ground

before lling.

• Always discharge static electricity before

using or servicing equipment by touching

a metal part of the dispenser before and

after fueling vehicle.

• Never smoke within 20 ft / 6.1 m of dispensers.

• Never keep in service past recommended life.

• Never leave the nozzle unattended while

dispensing fuel.

• Never use sparking or aming devices within

20 ft / 6.1 m of dispensers.

• Never use power tools near dispensers or

to aid in the installation process.

• Never use cell phone within 20 ft / 6.1 m of

dispensers.

• Never reenter car when fueling vehicle.

• Never allow gasoline to touch eyes or skin.

• Never use at ow rates in excess of

regulatory guidelines.

• Never use at ow rates less than 5 gpm /

18.9 Lpm.

• Never dispense ammable material into

unapproved containers.

• Never dispense fuel without a valid

driver’s license.

Patents: pending

Listings: pending

WARRANTY

VAPOR PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of one (1)

year of installation or fteen (15) months from the manufacture date of shipment by Husky, whichever occurs rst. The warranty period on

repaired or replacement vapor recovery products is only for the remainder of the warranty period of the defective product.

CONVENTIONAL PRODUCTS – Husky Corporation will, at its option, repair, replace, or credit the purchase price of any Husky

manufactured product which proves upon examination by Husky, to be defective in material and/or workmanship for a period of ONE (1)

YEAR from the manufacture date of shipment by Husky.

Buyer must return the products to Husky, transportation charges prepaid. This warranty excludes the replaceable bellows,

bellows spring assembly, spout assembly and scuff guard, unless (i) damage is obvious when the product is removed from shipping carton

and (ii) the defective product is returned to Husky prior to use. This warranty does not apply to equipment or parts which have been installed

improperly, damaged by misuse, improper operation or maintenance, or which are altered or repaired in any way.

The Warranty provisions contained herein apply only to original purchasers who use the equipment for commercial or

industrial purposes. There are no other warranties of merchantibility, tness for a particular purpose, or otherwise, and any other such

warranties are hereby specically disclaimed.

Husky assumes no liability for labor charges or other costs incurred by Buyer incidental to the service, adjustment, repair, return,

removal or replacement of products. Husky assumes no liability for any incidental, consequential, or other damages under any warranty,

express or implied, and all such liability is hereby expressly excluded.

Husky reserves the right to change or improve the design of any Husky fuel dispensing equipment without assuming any

obligations to modify any fuel dispensing equipment previously manufactured.

Husky Corporation • 2325 Husky Way • Pacic, MO 63069 • Phone: [phone] • Fax: [phone] • www.husky.com

009191-2 3/2009