Hunter 34407 Owner's Manual

ENGLISH

See page 2

FRANÇAIS

Voir page 18

Espanol

Voir page 9

Model 34407, 37407

Read and save these instructions.

e Care Free® Permawick™

Evaporative Humidiﬁer

SAFETY INSTRUCTIONS .........................................................2

How The Humidifier Works ........................................................ 2

Humidifier Parts .........................................................................2

Using Your Humidifier................................................................3

Features and Options ................................................................4

Refilling the Water Tank ........................................... 4

Humidifier Maintenance ............................................ 4

Troubleshooting ........................................................ 7

Service Parts ............................................................ 7

Table of Contents

Read and Save These Instructions

Important Safety Instructions:Read all

instructions before using this humidier.

1.This humidifier may not work properly on an uneven surface. ALWAYS place this humidifier on a firm, level, and

water resistant surface. ALWAYS place the humidifier at least six (6) inches away from walls and heat sources such as stoves, radiators, or heaters.

2. ALWAYS place the humidifier in an area that is out of the

reach of children.

3. Before using the humidifier, extend the cord and inspect

for any signs of damage. DO NOT use the product if the cord has been damaged.

4. This product has a polarized plug (one blade is wider than

the other) as a safety feature. This plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat or override this safety feature.

5. ALWAYS UNPLUG AND EMPTY the humidifier when it is

not in operation or while it is being cleaned.

6. DO NOT tilt or move the humidifier while it is in operation.

Never move the humidifier while there is water in the tank. Empty the water tank, turn off, and unplug the unit before moving.

7. In addition to routine maintenance which may be required,

this humidifier requires seasonal cleaning. Refer to and follow CLEANING THE HUMIDIFIER AND THE WATER TANK instructions.

How The Humidifier Works

The Hunter® Evaporative Humidifier has a unique patented design with several innovative features:

• Low Maintenance – Other humidifiers have paper filters

that need to be replaced every few months. Our exclusive PermaWick™ filter saves time and money. It’s designed to last season after season, saving up to $45 a year. No wet paper odors, either.

• Regulated Release™ System – By dispersing water from

the top of the PermaWick™ filter, stagnant water around the PermaWick™ filter is elimnated, and the buildup of mineral residue that can clog the filter and impede performance is eliminated. NOTE: The filter has a coating on the wick which may make it appear old or used, but is actually new.

• Built-in Antimicrobial Properties – The plastic parts and the

filter have built-in antimicrobial properties to inhibit the growth of bacteria, mold and fungi that may affect these parts.

NOTE: This product contains antimicrobial properties which are built-in to inhibit the growth of bacteria which may affect the plastic and filter in the humidifier. These properties do not extend to the water, humidified air or users. Conduct routine cleaning and maintenance based upon use and individual conditions.

• No White Dust – The Hunter® Evaporative Humidifier

produces no white dust that can settle on furniture or be inhaled.

NOTE: You may notice mineral deposits accumulating in the tank Tray. This is normal and does not affect performance. If you would like to clean these deposits away, please see CLEANING THE HUMIDIFIER AND WATER TANK.

Humidifier Parts

Figure 1

Wicks (3)

Water Tank

Tank Tote

Water Tank Cap(under Tank)

Control Panel

Main Housing

Drainage Tray

Tray

Power: Turns the humidifier on and off. the power should always be off before unplugging the humidifier, moving the humdifier, or refilling the water tank.

Refill Light: The red LED turns on to signal that the humidifier has automatically turned off and the Water Tank needs to be refilled.

Humidity: Enables you to set the desired maximum humidity level. Once this level is reached, the unit will automatically shut off until the humidity level drops. NOTE: The humidifier may not be running because the Span Setting may need to be adjusted. Speed: Sets the humdifier’s fan speed to Low (1), Medium (2), or High (3).

Timer: Sets the humidifier to run for 2, 4, 8, or 10 hours. when the timer is not used, the humidifier will run and cycle automatically.

Control Panel

Power

Timer

Humidity

NiteGlo™

Refill Tank LED (Red)

Speed

LED Display

Figure 2

Using Your Humidifier

1. Remove the Hunter® Evaporative Humidifier from its packaging.

2. Place the humidifier on a hard, flat, water resistant surface. Always place the humidifier at least six (6) inches away from walls and sources of heat.

3. Grasp the Water Tank by its Tank Tote and remove it from the Tray. See Figure 3.

4. Turn the Water Tank upside-down and remove the Water Tank Cap. See Figure 4.

Basic Set-Up and Operation

Twist to open

Figure 4

Water Tank Cap (under Tank)

Figure 3

Tank Tote

5. Fill the Water Tank with water, return the Water Tank Cap to its position and tighten it, and return the Water Tank to the Tray.

6. Plug the humidifier’s Power Cord into a standard household power outlet.

7. Press the Power Button on the Control Panel.

8. To see the current humidity, press the Humidity button. To change the humidity, press and hold the Humidity button for 3 seconds. The LED Display will flash the current humidity setting. Press the Humidity button until the LED Display shows your desired humidity setting. You can change the setting in 5% increments from 30% relative humidity to 80%. When the LED Dispaly shows your desired humidity setting, release the Humidity button. After 2 seconds, the humidity setting is set and the LED Display will show the relative humidity.

9. To see the current Fan speed setting, press the Speed button. To change the Fan speed setting, press and hold the Speed button for 3 seconds. The LED Display will flash the

+ 5 hidden pages