Humminbird UC 7SB User Manual
CHARGER
LADEGERÄT
CHARGEUR
CARICATORE
OPLADER
CARGADOR
UC 7SB
Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Lire soigneusement et bien assimiler ces instructions avant usage.
Prima dell’uso leggere attentamente e comprendere queste instruzioni.
Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.
Leer cuidadosamente y comprender estas instrucciones antes del uso.
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
1
1
2
2
6
3
1
4
Rechargeable battery Ladebatterie Batterie rechargeable
1
2
Name plate of battery Typenschild der Batterie Plaque nominale de la batterie
3
Insert Einsetzen Insérer
4
Pilot lamp Kontrollampe Lampe témoin
Hole for connecting the
5
rechargeable battery batterie rechargeable
6
Ventilation slot Ventilator Ventilateur
Batteria ricaricabile Oplaadbare batterij Batería recargable
1
Etichetta della batteria Naamplaatje van de batterij
2
Inserire lnsteken Insertar
3
Spia Kontrolelampje Lámpara piloto
4
Foro di collegamento della Aansluiting voor oplaadbare Agujero para conectar la batería
5
batteria ricaricabile batterij recargable
6
Ventola Ventilator Ventilador
English Deutsch Français
Anschlußloch für Akkumulator
Italiano Nederlands Español
Orifice de raccordement de la
Placa de características de la
batería
5
1
English
GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches
invite accidents.
2. Avoid dangerous environment. Don’t expose power
tools and charger to rain. Don’t use power tools
and charger in damp or wet locations. And keep
work area well lit. Never use power tools and
charger near flammable or explosive materials. Do
not use tool and charger in presence of flammable
liquids or gases.
3. Keep children away. All visitors should be kept
safe distance from work area.
4. Store idle tools and charger. When not in use,
tools and charger should be stored in dry, high
or locked-up place–out of reach of children. Store
tools and charger in a place where the temperature is less than 40°C.
5. Don’t abuse cord. Never carry charger by cord or
yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
6. When the charger is not in use, or when being
maintained and inspected, disconnect its power
cord from the receptacle.
7. To avoid danger, always use only the specified
charger.
8. Use only genuine HITACHI replacement parts.
9. Do not use power tools and charger for applications
other than those specified in the Handling
Instructions.
10. To avoid personal injury, use only the accessories
or attachment recommended in these handling
instructions or in the HITACHI catalog.
11. Let only the authorized service center do the
repairing. The Manufacturer will not be responsible for any damages or injuries caused by repair
by the unauthorized persons or by mishandling
of the tool.
12. To ensure the designed operational integrity of
power tools and charger, do not remove installed
covers or screws.
13. Always use the charger at the voltage specified
on the nameplate.
14. Always charge the battery before use.
15. Never use a battery other than that specified. Do
not connect a usual dry cell, a rechargeable battery
other than that specified or a car battery to the
power tool.
16. Do not use any transformer that has a booster.
17. Do not charge the battery from an engine electric
generator or DC power supply.
18. Always charge indoors. Because the charger and
battery heat slightly during charging, charge the
battery in a place not exposed to direct sunlight;
where the humidity is low and the ventilation
good.
PRECAUTIONS FOR CHARGER
1. Always charge the battery at a temperature of 10–
40°C. A temperature of less than 10°C will result
in over charging which is dangerous. The battery
cannot be charged at a temperature higher than
40°C. The most suitable temperature for charging
is that of 20 – 25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
3. Do not charge the battery for more than 1 hour.
The battery will be fully charged in about 1 hour
and charging should be stopped when 1 hour has
elapsed from commencement. Disconnect the
charger power cord from the receptacle.
4. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
5. Never disassemble the rechargeable battery and
charger.
6. Never short-circuit the rechargeable battery. Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
7. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
8. Using an exhausted battery will damage the
charger.
9. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
10. Do not insert object into the air ventilation slots
of the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
SPECIFICATIONS
CHARGER
Model UC7SB
Charging time Approx. 1 hour (at 20°C)
Charging voltage 7.2 V
Weight 1.0 kg
APPLICATION
For charging the HITACHI BATTERY (EB7).
2
English
CHARGING
Before using the power tool, charge the battery as
follows.
1. Insert the battery in the charger.
Position the battery so that the nameplate faces
toward the nameplate of the charger and press in
the battery until it comes into contact with the
bottom surface. (See Figs. 1 and 2)
2. Connect the charger power cord to the receptacle.
Connecting the power cord will turn on the charger
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the
power cord from the receptacle and check the
battery mounting condition.
About 1 hour is required to fully charge the battery
at a temperature of about 20°C. The pilot lamp goes
off to indicate that the battery is fully charged.
CAUTION
If the battery is heated due to direct sunlight,
etc., just after operation, the charger pilot lamp
may not light. At that time cool the battery first,
then start charging.
3. Disconnect the charger power cord from the
receptacle.
4. Hold the charger tight and pull out the battery.
MAINTENANCE AND INSPECTION
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
2. Cleaning of the charger
When the charger is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not
use chloric solvents, gasoline or paint thinner, for
they melt plastics.
3. Store idle charger
When not in use, the charger should be stored in
dry, high or locked-up place–out of reach of children.
.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
IMPORTANT
Correct connection of the plug
The wires of the mains lead are coloured in accordance
with the following code:
Blue: – Neutral
Brown: – Live
As the colours of the wires in the mains lead of this tool
may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black.
The wire coloured brown must be connected to the terminal marked with the letter L or coloured red.
Neither core must be connected to the earth terminal.
NOTE
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except United Kingdom.
3
Loading...