Humminbird Piranhamax User Manual

1

PiranhaMAX™ In-Dash Mounting Kit

Installation Overview

Following are instructions for the in-dash mount installation of the PiranhaMAX control head. We encourage
you to read this guide before starting the installation, so you may understand the installation requirements.

Customer Service: If you find that any items are missing from your installation kit, visit our Web site at
humminbird.com or call Humminbird® Customer Service at 1-800-633-1468.

Supplies: In addition to the hardware supplied with your In-Dash Mounting Kit, you will need a drill and

3/8" drill bit, cutting tool for cutting the dashboard material, safety glasses and dust mask, and masking
tape.

NOTE: Product supplies and features are subject to change without notice.

NOTE: The illustrations in this manual may not look the same as your product, but your unit will function in the same way.

1. Plan the Mounting Location

Start by locating a suitable, flat area of the dashboard for mounting. Consider the following to find the best
mounting location:

532463-1_B

• Stability: The mounting area should be protected from waves, shock, vibration, and water.

• Depth: The control head requires a depth of at least 3 inches (76 mm).

• Accessibility: The location should be easily accessible for all cables to reach the ports on the back of
the control head.

NOTE: If a cable is too short for your application, extension cables are available. For assistance, contact Humminbird
Customer Service.

2. Cut the In-Dash Mounting Hole

To in-dash mount the PiranhaMAX control head, start by placing the components on the surfaces where you
intend to install them.

1. Review the instructions, measurements, and cutting options indicated on the In-Dash Mounting
Template.

2. Tape the template to the chosen in-dash mounting location.

3. Using the template, select the cutting method that is best for your boat:

• Drill one entry hole away from the main cut line that is large enough to insert the blade of your

cutting tool.

OR

• Using a 3/8" drill bit, drill the 4 corner holes (inside the main cut line) as shown on the template.

Use one of the corner holes as an entry hole, or drill an additional entry hole away from the main
cut line.

4. Carefully begin cutting toward the cut line, and continue cutting to the inside of the line around the
template.

2

PiranhaMAX™ In-Dash Mounting Kit

5. Test the Mounting Hole: Install the control head in the mounting hole to test the fit. Make adjustments
to the mounting hole as needed. Remove the template when finished.

6. Thoroughly clean and deburr the mounting hole.

3. Install the Control Head

1. Insert and tighten the two threaded rods into the two threaded inserts located on the back side of the
control head. See the illustration Inserting the Threaded Rods.

2. From the front side of the dashboard, insert the control head through the mounting hole.

3. Press down lightly on the control head. Confirm the control head is centered and flush against the
dashboard. Make adjustments as needed.

4. From the back side of the dashboard, slide the bracket holes over the threaded rods. Install a nut onto
each threaded rod and hand-tighten until it is fully secure. Hand-tighten only! See the illustration
Assembling the Bracket.

5. Insert the cables into the ports on the back of the control head. The ports are keyed to prevent reverse
installation, so be careful not to force the connectors into the wrong port.

532463-1_B

Inserting the Threaded Rods

threaded rod

t

e

k

c

a

r

B

e

h

t

g

n

i

l

b

m

e

s

s

A

d

r

a

o

b

h

s

a

d

w

e

i

v

l

a

i

t

r

a

p

(

t

e

k

c

a

r

b

)

CAUTION! Do NOT mount the cables where the connectors could be submerged in water or flooded. If cables
are installed in a splash-prone area, it may be helpful to apply dielectric grease to the inside of the connectors to
prevent corrosion. Dielectric grease can be purchased separately from a general hardware or automotive store.

Inserting the Cables

h

t

i

w

t

u

n

r

e

h

s

a

w

k

c

o

l

t

s

e

s

o

l

c

e

d

i

s

t

e

k

c

a

r

b

o

t

3

PiranhaMAX™ In-Dash Mounting Kit

1-Year Limited Warranty

We warrant the original retail purchaser that products made by
Humminbird have been manufactured free from defects in materials
and workmanship. This warranty is effective for one year from the date
of original retail purchase. Humminbird products found to be defective
and covered by this warranty will be repaired or replaced free of charge
at Humminbird’s option and returned to the customer freight prepaid.
Humminbird’s sole responsibility under this warranty is limited to the
repair or replacement of a product that has been deemed defective by
Humminbird. Humminbird is not responsible for charges connected
with the removal of such product or reinstallation of replaced or
repaired parts; or shipping charges to the factory or authorized service
center (if outside the U.S.).

This warranty does not apply to a product that has been:

• Improperly installed;

• Used in an installation other than that recom mended in the
product installation and operation instructions;

• Damaged or has failed because of an accident or abnormal
operation;

532463-1_B

Humminbird Service Policy

Even though you’ll probably never need to take advantage of our
incredible service policy, it’s good to know that we back our products
this confidently. We do it because you deserve the best. We will make
every effort to repair your unit within three business days from the
receipt of your unit at our factory. This does not include shipping time to
and from our factory. Units received on Friday are typically shipped by
the following Wednesday, units received Monday are typically shipped
by Thursday, etc.

All repair work is performed by factory-trained technicians to meet
exacting factory specifications. Factory-serviced units go through the
sa m e rigo rous te s ting and qualit y control insp e ctions as new
production units.

After the original warranty period, a standard flat rate service charge
will be assessed for each repair (physical damage and missing parts are
not included). Any repairs made after the original warranty will be
warranted for an additional 90 days after service has been performed
by our factory technicians. You can contact our Customer Service or
visit our Web site to verify the flat rate repair fee for your product (visit
the Product Support section):

• Repaired or modified by entities other than Humminbird.

Please retain your original receipt as a proof of the purchase date. This
will be required for in-warranty service.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND
WILL BE THE CUSTOMER’S EXCLUSIVE REMEDY, EXCEPT FOR ANY
APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE
HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. IN NO EVENT WILL HUMMINBIRD BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH
OF AN Y EXPRESS OR IMPLIED WARRANTY RELATING TO THE
PRODUCTS.

Some states do not allow limitations on an implied warranty, or the
exclusion of incidental or consequential damages, so the above
exclusions may not apply to you. You may also have other rights, which
vary from state to state.

http://www.humminbird.com

We reserve the right to deem any product unserviceable when
replacement parts are no longer available or impossible to obtain. This
Service Policy is valid in the United States only. This applies only to
Humminbird products returned to our factory in Eufaula, Alabama. This
Service Policy is subject to change without notice.

DOMESTIC (USA) CUSTOMERS:

PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE

For all technical issues please call 1-800-633-1468

or visit www.humminbird.com, click SUPPORT.

Please reference product serial number and

model number when contacting Humminbird.

4

PiranhaMAX™ In-Dash Mounting Kit

Returning Your Unit for Service

Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.

NOTE: Please do not return your Humminbird to the store for service.

Please have your product model name and serial number available
before calling the factory. If you contact the factory by e-mail, please
include your product model name and serial number in the e-mail, and
use Request for Repair Authorization Number for your e-mail subject
header. You should include your Repair Authorization Number in all
subsequent communications about your unit.

For IN-WARRANTY service, complete the following steps

• Obtain a Repair Authorization Number from Humminbird Customer
Service.

• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.

• Include a brief written description of the problem.

• Include a copy of your receipt (to show proof and date of purchase).

• Return product freight prepaid to Humminbird, using an insured
carrier with delivery confirmation.

For OUT-OF-WARRANTY service, complete the following steps

• Obtain a Repair Authorization Number from Humminbird Customer
Service.

• Include payment in the form of credit card number and expiration
date, or a money order. Please do not send cash.

• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.

• Include a brief written description of the problem.

• Return product freight prepaid to Humminbird, using an insured
carrier with delivery confirmation.

:

:

532463-1_B

Contact Humminbird

Web site humminbird.com

E-mail [e-mail]

Telephone [phone]

Direct Shipping Humminbird

Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA

WARNING! This device should not be used as a navigational aid to
prevent collision, grounding, boat damage, or personal injury. When the
boat is moving, water depth may change too quickly to allow time for you
to react. Always operate the boat at very slow speeds if you suspect
shallow water or submerged objects.

WARNING! Disassembly and repair of this electronic unit should only be
performed by authorized service personnel. Any modification of the serial
number or attempt to repair the original equipment or accessories by
unauthorized individuals will void the warranty.

ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Johnson
Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating
in compliance with known and applicable environmental regulations, and a good
neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and Electronic
Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers
of consumer electronics in the European Union. The WEEE Directive requires the
producer of consumer electronics to take responsibility for the management of
waste from their products to achieve environmentally responsible disposal during
the product life cycle.

WEEE compliance may not be required in your location for electrical & electronic
equipment (EEE), nor may it be required for EEE designed and intended as fixed or
temporary installation in transportation vehicles such as automobiles, aircraft, and
boats. In some European Union member states, these vehicles are considered
outside of the scope of the Directive, and EEE for those applications can be
considered excluded from the WEEE Directive requirement.

This symbol (WEEE wheelie bin) on product indicates the product must not
be disposed of with other household refuse. It must be disposed of and
collected for recycling and recovery of waste EEE. Johnson Outdoors

Marine Electronics, Inc. will mark all EEE products in accordance with the
WEEE Directive. It is our goal to comply in the collection, treatment, recovery, and
environmentally sound disposal of those products; however, these requirements do
vary within European Union member states. For more information about where you
should dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer or
distributor from which your product was purchased.

© 2017 Johnson Outdoors Marine Electronics, Inc. All rights reserved.