Humax BLU4-FOX CI User Manual

Digital Satellite Receiver

The default Password is 0000.

User’s Manual

BLU4-FOX CI

Notice

Thank you for purchasing a HUMAX product. Please read this user’s manual carefully to be able to safely install, use and maintain the product at maximum performance. Keep this user’s manual next to your product for future reference. The information in this user’s manual is subject to change without notice.

Not to be copied, used or translated in part or whole without HUMAX's prior consent in writing except approval of ownership of copyright and copyright law.

Warranty

The warranty does not cover parts which may become defective due to misuse of the information contained in this manual.

Trademarks

Nagravision is a registered trademark of KUDELSKI S.A.

Manufactured under license from Dolby Laboratories.

'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from entavio.

Manufactured under license from BLUCOM.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Hereby, HUMAX, declares that this digital satellite receiver is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Notice

Warnings, Cautions and Notes

Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations.

Warning

Indicates a hazardous situation which could result in serious injury.

Caution

Indicates a situation which could damage the equipment or other apparatus.

Note

Indicates additional information to make the user aware of possible problems and information of any importance to help understand, use and maintain the installation.

Meaning of Symbols

To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

This symbol indicates dangerous voltage inside the product that presents a risk of

Instruction about the ‘WEEE’ Symbol

electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

This product should not be disposed with other household wastes at the end of its working life. Please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. This will prevent possible harm to the environment or human health from uncontrolled waste disposal. Domestic users: Please contact either the retailer where you purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling. Business users: Contact your supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Safety Warning

This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully.

Safety Instructions and Precautions

1. MAINS SUPPLY

90-250V a.c., 50/60Hz Operate this product only from the type of power supply indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your local power company. Disconnect the product from the mains before you start any maintenance or installation procedures.

2. OVERLOADING

Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock.

3. LIQUID

The product should not be exposed to liquid of any kind. In addition, no objects filled with liquid should be placed on the apparatus.

4. CLEANING

Disconnect the product from the wall outlet before cleaning. Use a light damp cloth (no solvents) to dust the product.

5. VENTILATION

The slots on top of the product must be left uncovered to allow proper airflow into the unit. Do not stand the product on soft furnishings or carpets. Do not stack electronic equipments on top of the product.

6. ATTACHMENTS

Do not use any unsupported attachments as these may be hazardous or cause damage to the product.

7. CONNECTION TO THE SATELLITE DISH LNB

Disconnect the product from the mains before connecting or disconnecting the cable from the satellite dish. Failure to do so can damage the LNB.

8. CONNECTION TO THE TV

Disconnect the product from the mains before connecting or disconnecting the cable from the TV. Failure to do so can damage the TV.

9. EARTHING

The LNB cable must be earthed to the system earth for the satellite dish.

Safety Warning

10.LOCATION

• Place the product indoors to avoid exposing it to lightning, rain or sun.

• Do not place it near a radiator or heat register.

• Make sure it has more than 10 cm clearance from any appliances susceptible to electromagnetic influences, such as a TV or a VCR.

• Do not block the openings with any object, and do not place the product on a bed, sofa, rug, or other similar surface.

• If you place the product on a rack or a bookcase, ensure that there is adequate ventilation and that you have followed the manufacturer’s instructions for mounting.

• Do not place the product on an unstable cart, stand, tripod, bracket, or table where it can fall.

• A falling product can cause serious injury to a child or adult, and serious damage to the appliance.

11.LIGHTNING, STORM OR NOT IN USE

Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-surges.

12.EXTRANEOUS OBJECTS

Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts.

13.REPLACEMENT OF PARTS

When replacement of parts is required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitution may result in additional damage to the unit.

Warning

The mains plug, as a disconnection device, shall remain readily accessible by the user.

1. To avoid damage of the power cord or plug;

• Do not modify or process the power cord or plug arbitrarily.

• Do not bend or twist the power cord.

• Make sure to disconnect the power cord holding the plug.

• Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from melting.

• The main plug shall remain readily operable.

2. To avoid electrical shock;

• Do not open the main body.

• Do not insert metal or inflammable objects inside the product.

• Do not touch the power plug with wet hands.

• Disconnect the power cord in case of lightning.

3. To avoid damage of product;

• Do not use the product when it is out of order. If you continue to use the product when defective, serious damage can be caused to it. Make sure to contact your local product distributor if the product is out of order.

• Do not insert metal or alien substance into the slots for the modules or Smartcards. It may cause damage to the product and reduce its life span.

Contents

1. Before Using the Product ....................................... GB8

1.1 Package Contents .......................................... GB8

1.2 Front Panel ................................................ GB9

1.3 Conditional Access.......................................... GB10

1.4 Rear Panel................................................. GB12

1.5 Remote Control............................................. GB13

2. Setup..........................................................GB15

2.1 Connecting the Antenna/TV/VCR ............................. GB15

2.2 Connecting the Audio System ................................ GB17

2.3 Powering On ............................................... GB18

3. Installation Wizard.............................................. GB19

3.1 Language.................................................. GB19

3.2 Country.................................................... GB19

3.3 Antenna Setting ............................................ GB20

3.4 Software Update............................................ GB20

3.5 Select Service List .......................................... GB21

4. Basic Operation ................................................GB22

4.1 Switching Channel .......................................... GB22

4.2 Volume Control ............................................. GB22

4.3 Option List ................................................. GB23

4.4 Programme Information (i-plate) .............................. GB25

4.5 Mosaic Channels ........................................... GB27

5. Channel List ...................................................GB28

5.1 All Channel List............................................. GB28

5.2 Favourite List............................................... GB31

5.3 Bouquet List................................................ GB32

5.4 Scramble List............................................... GB32

6. EPG...........................................................GB33

6.1 EPG Main.................................................. GB33

6.2 EPG Table ................................................. GB35

6.3 Schedule List............................................... GB36

6.4 Find Programme............................................ GB37

7. entavio Menu .................................................. GB40

7.1 PIN-Code Change .......................................... GB40

7.2 Smartcard ................................................. GB43

7.3 CI-Module ................................................. GB43

7.4 Software Update............................................ GB44

7.5 Antenna Setting ............................................ GB45

7.6 Standard Search............................................ GB47

7.7 Expert Search ..............................................GB48

Contents

8. Setting ........................................................ GB49

8.1 Parental Control ............................................ GB49

8.2 Country Setting ............................................. GB51

8.3 Language Setting ...........................................GB52

8.4 Time Setting ............................................... GB54

8.5 A/V Setting................................................. GB56

8.6 Dolby Digital ............................................... GB58

8.7 Other Settings .............................................. GB59

8.8 BLUCOM Setting ........................................... GB61

9. Edit Channels ..................................................GB64

9.1 Edit Preferred Channels ..................................... GB64

9.2 Edit Channels .............................................. GB65

9.3 Edit Favourite Channels ..................................... GB68

10. Installation.................................................... GB71

10.1 Search Channels .......................................... GB71

10.2 SMATV Search............................................ GB83

10.3 Default Setting ............................................ GB85

11. Software Update .............................................. GB86

11.1 OTA (Over the Air) ......................................... GB86

12. Menu Map .................................................... GB88

13. Trouble Shooting.............................................. GB89

13.1 Trouble Shooting .......................................... GB89

13.2 Error Message ............................................ GB91

14. Specification..................................................GB93

15. Glossary...................................................... GB95

16. Service and Support...........................................GB97

1. Before Using the Product

1.BeforeUsing theProduct

This chapter provides detailed instructions on the product and its accessories.

1.1 Package Contents

Please check all package contents before using your product.

** **

Front Panel

Remote Control SCART-Cable

User's Manual Batteries

Note:

• Faults may occur if the remote control is left without battery for a long time. Always keep the battery inserted in the remote control.

• Package contents may vary according to area.

1. Before Using the Product

1.2 Front Panel

1. STANDBY LED

Red light is emitted when the product is in standby mode.

2. STANDBY BUTTON

Switches between operation and standby modes.

3. TV/RADIO BUTTON

Switches between TV and radio modes.

4. P-/P+ BUTTON

Moves the TV/radio channels up or down.

5. TV LED

Green light is emitted when the product is in TV mode.

6. RADIO LED

Amber light is emitted when the product is in radio mode.

7. SMARTCARD SLOT

A slot for a Smartcard

8. CI-MODULE SLOT

A slot for a CI-Module

1. Before Using the Product

1.3 Conditional Access

Although some TV and radio channels are free to air, most TV and radio/music channels are available on a subscription basis and can only be enjoyed via an appropriate Smartcard. The Conditional Access component is a removable Smartcard.

1. Inserting the Smartcard

The Smartcard looks similar to a credit card and is inserted into the slot behind the right-hand front flap of the product. A valid Smartcard entitles you to view and listen to all the channels you choose to subscribe to.

1. Open the right-hand flap on the front panel of the product. Swing it downwards to expose the card slot.

2. Hold the Smartcard horizontally with the electronic chip (small square-shaped, gold in colour) facing upwards.

3. Insert the Smartcard into the slot.

1. Before Using the Product

2. Inserting a CI-Module (with Smartcard)

A CI-Module looks like a PC map (PCMCIA) for laptops. There are different kinds of CI-Modules suitable for different coding systems; Irdeto, Conax and more. Additionally to the CI-Module, a Smartcard is needed to decode the channels.

1. Open the right-hand flap on the front of the product.

2. Follow the instructions of the module and insert the Smartcard into the CI-Module.

3. Keep the CI-Module (with the Smartcard) horizontal.

4. Insert the CI-Module into the slot.

1. Before Using the Product

1.4 Rear Panel

1. IF INPUT

Connects a satellite antenna cable.

2. IF OUTPUT

Connects another digital satellite receiver.

3. TV SCART

Connects to the TV using a TV SCART cable.

4. VCR/AUX SCART

Connects to the VCR or DVD using a VCR SCART cable.

5. AUDIO L/R

Connects to the TV or VCR using an RCA cable.

6. VIDEO

Connects to the TV or VCR using an RCA cable.

7. DATA I/O

Connects to the PC to update software.

8. OPTICAL

Connects to the audio system using an S/PDIF cable. (digital audio)

1. Before Using the Product

1.5 Remote Control

1. Before Using the Product

1. SOURCE

Selects the input source between TV and the product.

2. TV/RADIO

Switches between TV and radio modes.

3. NUMERIC(0-9) BUTTONS

Enters a TV/radio channel number or menu option number.

4. LIST

Displays the channel list.

5. BACK

Closes and returns to the previous menu and screen.

6. ARROW BUTTONS

Changes the channel or moves the cursor up, down, left or right.

7. OK

Selects a menu or confirms the selected operation. Displays the channel list while watching a programme.

8. COLOUR BUTTONS (R/G/Y/B)

Select the colour keys for interactive applications.

9. P-/P+

Changes the channel.

10.MENU

Displays the main menu.

11.PAGE

Changes the page.

12.STANDBY

Switches between operation and standby modes.

13.EPG

Displays the EPG (electronic programme guide).

14.EXIT

Exits all On-Screen Display (OSD) screens.

15.V-/V+

Adjusts the audio volume.

16.MUTE

Mutes or unmutes the audio temporarily.

17.i (Information)

Displays the channel and programme information.

18.TEXT

Switches between the teletext and TV modes.

19.OPT

Displays the audio, Multifeed, teletext and subtitle language services.

2. Setup

2.Setup

This chapter describes how to connect your product to the TV with the particular equipments for gaining optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other devices. Select the most appropriate procedure depending on the equipment you have.

Note: If you encounter any problems setting up your product, please contact your local product distributor.

2.1 Connecting the Antenna/TV/VCR

1. Using SCART Cable

Connect the product and the TV or VCR using the SCART cable as follows.

Note: Connecting your TV directly to the Audio/Video output of the product will assure a more vivid picture and

enhance your viewing enjoyment.

2. Setup

2. Using RCA Cable

Connect the product and the TV using the RCA cable as follows.

2. Setup

2.2 Connecting the Audio System

Connect the product and the audio system using the RCA (Audio L, R) cable as follows. If you wish to connect the OPTICAL terminal and Dolby Digital decoder to listen to digital audio, connect as follows.

2. Setup

2.3 Powering On

1. Connect the power cord of the product to a wall outlet.

2. Power on by pressing the STANDBY button on the remote control or the STANDBY button on the front of the product.

3. Installation Wizard

3.InstallationWizard

When powering on your product for the first time after purchase, the installation wizard will operate automatically. This chapter includes the first time setup of the language, country, search channel and software update which will show you how to start the initial installation.

Note:

• The default password is 0000.

• If you have forgotten your password, please contact your local product distributor.

3.1 Language

Language allows you to select the main language.

Select the appropriate language from the list using the button and press the OK language.

Note: The display language may differ according to country.

button to save the selected language as a default

3.2 Country

You can select the country.

Select your region from the list using the

button.

button and press the OK

3. Installation Wizard

3.3 Antenna Setting

You can configure the settings for channel search.

1. Satellite: Only the channels in ASTRA1 can be searched in installation wizard. To search channels in different satellites, go to Chapter10.

2. LNB Frequency: Select the required LNB frequency using the OK

button and press the OK button.

3. 22kHz Tone: Select Enable/Disable using the OK

press the OK

4. DiSEqC Input: Select the required DiSEqC input using the OK

button and press the OK button.

5. Select Next and press the OK

button.

or button and

button.

3.4 Software Update

You can check the current software version and update new software. Select Next and press the OK button.

When new software is detected, select Now and press the OK button if the software requires mandatory update.

In case of non-mandatory software, select Yes or No and press the OK

button.

3. Installation Wizard

3.5 Select Service List

You can select the service list. Select Next and press the OK button.

The list will be displayed. Select an option from the searched service list using the

service list is updated. Press the OK

The search results of the selected service list will appear. Select Finish and press the OK button to complete the installation wizard.

To go back to the previous step, select Back and press the OK button.

If you want to search more channels, press the OK button. You can search channels in the main menu.

button and press the OK button. Wait until the

button to go to the next step.

4. Basic Operation

4.BasicOperation

This chapter describes the basic functions of the product such as switching channel, volume control, option list and programme information. You can check or change the settings.

4.1 Switching Channel

Switching Channel allows you to switch the current channel using one of the following methods.

1. Press the P-/P+

2. Enter the channel number using the NUMERIC(0-9) buttons to move to the channel directly.

3. Press the TV/RADIO

Note: You can switch channels using the channel list or EPG.

To return to the previous channel, press the BACK

button.

button to switch between TV channels and radio channels.

button.

4.2 Volume Control

Volume Control allows you to adjust the audio volume.

1. Press the V-/V+ button to adjust the audio volume.

2. Press the MUTE

Note: The mute function remains set while you switch channels.

button to stop the audio temporarily.

4. Basic Operation

4.3 Option List

Option List allows you to set options such as audio, multifeed, teletext and subtitle language.

1. Audio

You can select the language you prefer in Audio if the current programme is available in multiple audio languages.

1. Press the OPT button.

2. Select Audio using the

3. Select the audio language you prefer using the press the OK

4. Select audio direction (left, right, stereo) using the

Note:

• You can select the required audio language in 8.2 Language Setting.

• If the programme is broadcast in Dolby Digital, you cannot set the audio direction.

button.

2. Multifeed

You can choose from a choice of camera angles to watch the screen from different camera perspectives while watching a sports transmission. Different options are provided to view single matches or federal league games.

1. Press the OPT

2. Select Multifeed using the

3. Select the required option using the

button.

button and press the button.

button and

button.

button and press the button.

button and press the

3. Teletext

You can use your TV remote control unit to control the teletext service. All teletext supporting channels have the teletext icon on the i-plate.

1. Press the OPT

2. Select Teletext using the

Note: You can also use the TEXT button on your remote control to view teletext.

button.

button and press the the button.

4. Basic Operation

4. Subtitle

You can select the language for the subtitle if the programme provides subtitle information.

1. Press the OPT button.

2. Select Subtitle using the

3. Select the required subtitle language using the press the OK selected language at the bottom of the screen.

4. Select Off from the subtitle language list to hide subtitle from the screen.

button. The subtitle will be displayed in the

button and press the button.

button and

4. Basic Operation

4.4 Programme Information (i-plate)

Programme information is always displayed for a certain period of time whenever you switch channels. You can view the programme information by pressing the i button while watching a programme. Press the EXIT button to

hide the i-plate.

1. General Information

The general information is displayed on the screen as the following.

1. Channel number and name

2. Icons

Displayed only when the channel is a scrambled channel.

Displayed only when subtitle information is available.

Displayed only when there is any teletext information.

Displayed only when the programme is broadcast in Dolby Digital.

Displayed only if this programme is reserved.

Represents parental level. Indicates the minimum level of age for viewing the programme.

Displayed when BLUCOM services are provided.

Displayed when the audio track is dual mono.

4. Basic Operation

3. Programme name

4. Current time & date

5. Next programme information: Displayed if next programme information is provided. Press the next programme information.

6. Programme broadcasting time and progress bar: Displays programme playing time and progress bar.

7. Option: Displayed if options such audio, multifeed, teletext or subtitle are provided.

8. Detailed programme information: Displayed if detailed programme information is provided.

Note: If there is no programme information available, programme information is not displayed.

2. Detailed Programme Information

You can see the detailed information about the current programme. Press the i button where the i-plate is displayed to view detailed

information.

Note:

• Press the i

• If the detailed programme information is over one page, use the

PAGE

button again to hide the information box.

button to move to the previous or next page.

button to display

4. Basic Operation

4.5 Mosaic Channels

You can view the mosaic channels the broadcaster sends; icons for each broadcasting service are displayed in cell forms. To move to the selected channel, place the cursor on the cell representing the channel you wish to view.

When mosaic channels are available, a mosaic linkage icon (consists of a red dot and text) appears on the upper right of the screen while watching a non-mosaic channel. The mosaic linkage icon will disappear from the screen after a few seconds and reappear on the upper right of the i-plate as a red dot.

While the icon is displayed,

BACK The icon disappears. Exits mosaic channels.

RED Moves to mosaic channels.

While there is no icon,

BACK Returns to the previous channel.

1. Press the RED button on the remote control to move to mosaic

2. Move the cell cursor to a selected channel and press the OK

3. Press the BACK button on the remote control to exit mosaic

Note: The i-plate does not appear when the channel is a mosaic

channels.

button to switch to the channel the cell cursor is currently on.

channels.

channel. The EIT information is displayed on the bottom of the screen when provided. Up to eight groups of recently viewed mosaic channels can be saved.

5. Channel List

5.ChannelList

This chapter will help you display the channel list using the LIST button and switch to another channel in the channel list.

Six types of channel lists are provided for quick and easy channel search.

TV The list of all TV channels

Radio The list of all radio channels

Favourite The list of the favourite channels in five groups

Bouquet The list of channels classified by bouquets

Satellite The lists of channels classified by satellites

Scramble The lists of channels classified by CAS types

Note:

• Press the EXIT

• The channel list is updated automatically when changes occur.

5.1 All Channel List

All Channels List allows you to delete, rename or include the channels in Favourite. You can also use lock/unlock functions or configure the menu.

1. Press the LIST button while watching a programme.

2. Press the RED channel list is displayed.

3. Select the channel you wish to view using the press the OK

4. You can also enter the channel number using the NUMERIC(0-9) buttons and press the OK

channel.

5. Press the LIST TV or Radio, and press the OK

6. To switch to TV or Radio, press the RED

Note: You can switch between TV/radio by simply pressing the

TV/RADIO button on the remote control.

button to exit the Channel List.

button on the remote control while the

button and

button.

button to change to a certain

button again and select one option among

button.

button again.

5. Channel List

1. Deleting Channels

1. Select a channel to delete and press the i button.

2. Select Delete using the button.

3. A pop-up will appear. Select Yes and press the OK button.

4. You will be prompted to enter your password. Enter your password and press the OK

Note:

• You cannot delete items from Favourite channel list.

• The default password is 0000.

• You cannot delete LCN channels.

button and press the OK

button.

2. Renaming Channels

1. Select a channel to rename and press the i button.

2. Select Rename using the button.

button and press the OK

+ 70 hidden pages