Huffy Sidewalk Ride-on Owner's Manual

Owner’s Manual for

Kids Ride-On

Manuel du propriétaire

Bicyclette pour Enfants

This manual contains important safety, assembly, operation

and maintenance information.

Please read and fully understand this manual

before operation.

Save this manual for future reference.

Ce manuel contient des renseignements relatifs à la sécurité,

l’assemblage, le fonctionnement et l’entretien du produit.

Lire et s’assurer d’avoir bien compris ce manuel du

propriétaire avant toute utilisation du produit.

Conserver ce manuel pour référence ultérieure.

H-Sidewalk-Rideon EN FR 102913 m0148

English

Kids Ride-On

Thank you for your purchase.

If this product does not meet your expectations, if

you have any questions or if there are any

damaged parts, before returning it to the store,

please contact customer service.

These instructions are generalized for direct drive

ride-on products. The image might not look

Kids Ride-On

exactly like your product, the assembly

instructions and warnings are correct.

Please keep this sheet for future reference.

WARNING:

Adult assembly is required. Keep

small loose parts and plastic bags

out of the reach of children.

WARNING:

1) Adult supervision is required.

2) Obey all local laws.

3) This unit is recommended for ages 3 years & up.

4) Max weight is 60 lbs. (27 kg)

5) Never ride with more than one person.

6) Do not ride the product over large objects.

7) Ride on smooth paved surfaces away from motor

vehicles.

8) Do not ride the product near steps, sloped driveways, hills, roadways, alleys, and swimming pool areas.

9) Do not ride at dusk, at night or at times of limited visibility.

10) Do not ride the product in wet weather.

11) Wear protective clothing when using the product,

including an approved helmet and shoes.

12) Do not ride wearing anything that obstructs hearing or visibility.

13) Replace worn or broken parts immediately.

14) DO NOT REMOVE THE STABALIZING WHEELS

15) THIS IS A DIRECT DRIVE PRODUCT, IT DOES NOT HAVE

A BRAKE

All components are warranted against manufacturing defects for six (6) months from the date of purchase.

Assembly Instructions

Note: All models may not have all parts and features shown. Assembly of all models is

similar.

Assemble the product as shown in the diagram. Some items may have been pre-

assembled.

1) Install the fork onto the frame as shown, with the slot in the steerer tube oriented toward the rear.

2) Place the clamp assembly onto the steerer tube with the open end of the clamp in-line with the slot in the steerer tube.

3) Slide the clamp cover as far up the stem as possible.

4) Insert the handlebar stem into the steerer tube. Ensure the minimum insertion

mark on the stem is not visible – below the top of the steerer tube.

5) Align the handlebar so that they are perpendicular with the rear wheel.

6) Secure the handlebar in the steerer tube with the clamp.

7) Check that the clamp is tight enough so that the handlebar will not rotate inside

the steerer tube.

8) Install the seat onto the frame (this is pre-assembled on some models). Ensure that the minimum insertion mark on the seatpost is not visible – below the top of the frame.

9) Ensure the seat clamp hardware is sufficiently tightened to hold the seat firmly onto the frame.

10) Insert each front wheel lug into the fork tube as shown. (This is easily accomplished with the product upside down resting on the handlebar & seat.) Secure the lugs onto the fork with the hardware. Sufficiently tighten the hardware to hold the lugs.

11) Install the side plates using the hardware provided (ties, screws or snaps).

12) Insert the rear wheel into the frame.

13) Install the wheel stabilizers and hardware as shown. Ensure the anti-rotation tab

on the stabilizer hardware is located in the slot in the frame. Sufficiently tighten the rear axle hardware to hold the wheel onto the frame. Note: The wheel stabilizers are not intended to be removed. The product will be difficult to ride without them.

14) Install any accessories provided.

15) Ensure all the hardware is tight, and will not come off.

Check the product and secure all fasteners before each use.

Parts List

Description Qty

Frame 1 Front Wheel Ass’y____ 1

(includes pedals)

Fork Ass’y__________ 1 Handlebar Ass’y 1 Seat & Seatpost Ass’y 1 Wheel Stabilizer Ass’y 2 Stem Clamp Ass’y 1 Stem Clamp Cover 1 Front Wheel Hardware 2 Rear Wheel Hardware 2 Seat Mount Clamp & H’ware 1 Fork Stem Bushings_ 2 Side plates _________ 2

Accessories: (some models) Front & Rear Fenders Handlebar Pad Handlebar Plaque Handlebar Sound Plaque Front Basket Streamers / Bell

This product does not require maintenance. However the unit should be checked periodically for loose, worn or

damaged parts. Tighten any that are loose, and replace any worn or damaged parts immediately.

Tools Required for Assembly: 12; 13; and 14mm wrenches, or small adjustable wrench.

Kids Ride-On

Minimum Insertion Mark

English

Maintenance

This product does not require lubrication.

Periodic cleaning will prolong the useful life of the product.

Minimum Insertion Mark

Side plates install with ties,

screws or snaps (ties shown)

Seat to Seat Post (Single Bolt Style): Some models are equipped with a seat and seat post assembly that uses a Single Bolt and Nut (A) to secure the Seat (B) to the seat post. The seat is assembled to the seat post at the factory.

Ensure the Seat is secure to the Seat Post and the seat bolt is tightened. Recommended torque = 7.3 ft-lbs (10 N•m).

27118v022709

+ 5 hidden pages