09/04 P/N 211574
1
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632-792
Internet Address: www.huffysports.com
HUFFY
Portable Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
• 2 People
• Tape Measure
• Wood Board (scrap)
• Sawhorse or
Support Table
• Hammer
• Tape
• Phillips Screwdriver
• (2 each) Wrenches and/or
Socket Wrenches and
Sockets (Deep-Well Sockets
are Recommended).
• Extension is Recommended.
7/16" 1/2" 9/16" 3/4"
AND/OR
• Garden Hose or
Sand
• Step Ladder
8ft. (2.4 m)
• Optional: Large &
Small Adjustable
Wrenches
SAND
SAND
(360 lb.)
(360 lb.)
(163 kg)
(163 kg)
7/16" 1/2" 9/16" 3/4"
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
WARNING!
HUFFY
SPORTS
2
P/N 211574 09/04
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT
IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow
these rules for safe operation of the system.
• DO NOT HANG on the rim or any part of the system
including backboard, support braces or net.
• During play, especially when performing dunk type
activities, keep player's face away from the backboard, rim
and net. Serious injury could occur if teeth/face come in
contact with backboard, rim or net.
• Do not slide, climb, shake or play on base and/or pole.
• After assembly is complete, fill system completely with
water or sand and stake to the ground. Never leave system
in an upright position without filling base with weight, as
system may tip over causing injuries.
• When adjusting height or moving system, keep hands and
fingers away from moving parts.
• Do not allow children to move or adjust system.
• During play, do not wear jewelry (rings, watches, necklaces,
etc.). Objects may entangle in net.
• Surface beneath the base must be smooth and free of
gravel or other sharp objects. Punctures cause leakage and
could cause system to tip over.
• Keep organic material away from pole base. Grass, litter,
etc. could cause corrosion and/or deterioration.
• Check pole system for signs of corrosion (rust, pitting,
chipping) and repaint with exterior enamel paint. If rust has
penetrated through the steel anywhere, replace pole
immediately.
• Check system before each use for proper ballast, loose
hardware, excessive wear and signs corrosion and repair
before use.
• Check system before each use for instability.
• Do not use system during windy and/or severe weather
conditions; system may tip over. Place system in the
storage position and/or in an area protected from the wind
and free from personal property and/or overhead wires.
• Never play on damaged equipment.
• See instruction manual for proper installation and
maintenance.
• When moving system, use caution to keep mechanism from
shifting.
• Keep pole top covered with cap at all times.
• Do not allow water in tank to freeze. During sub-freezing
weather add non-toxic antifreeze, sand or empty tank
completely and store. (Do not use salt.)
•
While moving system, Do not allow anyone to stand or sit
on base or have added ballasting on base.
• Do not leave system unsupervised or play on system when
wheels are engaged for moving.
• Use Caution when moving system across uneven surfaces.
System may tip over.
• Use extreme caution if placing system on sloped surface.
System may tip over more easily.
201246 2/99
In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339
09/04 P/N 211574
3
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to instructions. Failure to follow instructions could
result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
• If using a ladder during assembly, use extreme caution.
• Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to seperate during play and/or during transport of the system.
• Climate, corrosion or misuse could result in system failure.
• If technical assistance is required, contact Huffy Sports.
• Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com/warrantycard or mail-in
the enclosed postcard.
4
P/N 211574 09/04
WARRANTY CARD:
Please remember to complete your product
registration form either
on-line at:
www.huffysports.com/warrantycard
or mail-in the enclosed postcard.
PARTS LIST (See Hardware Identifier)
Item Qty. Part No. Description
11900026 Top Pole Section, Black
21908107 Middle Pole Section, Black
31908028 Bottom Pole Section, Black
4 1 200188 Rod, Zinc 3/8 x 5-1/4 Long
5 1 202822 Eyebolt, 3/8–16 x 3-3/4 Long
6 1 200117 Base
7 1 203124 Stake, Tie Down
8 4 203063 Lock Nut, Nylon Insert, 3/8–16
9 2 906410 Struts, Base
10 1 202662 Bolt, 5/16-18 x 4-1/2 Long
11 7* 203218 Washer, Flat, 5/16 x 7/8 O.D.
12 1 203220 Lock Nut, Nylon Insert, 5/16-18
13 1 200516 Vinyl, Bolt Cover, 5/16
14 2 203798 Bolt, Hex Flange, 5/16-18 x 1-1/2 Long
15 20* 203100 Lock Nut, Whiz, 5/16-18
16 1 203223 Bolt,Carriage 5/16-18 X 1.00” Long
17 2 226401 Wheel 4” Diameter
18 1 200123 Upper Pivot Bracket
19 1 200512 Bolt, Hex Head,3/8-16 x 3-1/2 Long
20 9* 203232 Washer, 3/8 I.D., x 3/4 O.D.
21 1 206252 Bolt, Hex Head, 3/8-16 x 1 Long
22 1 206948 Lower Pivot Bracket
23 1 203330 Bolt, Hex Head, 3\8-16 x 4-1/2 Long
24 2 900122 Hinge Tubes
25 2 900223 Wheel Bracket
26 6 203103 Bolt, Carriage, 5/16-18 x 2 Long
27 2 226403 Wheel 6” Diameter
28 2 206940 Axle, .461 O.D. x 21 Long
29 4 206938 Push Caps
30 1 206956 Disc, Plastic, 5” O.D. x .0625 Thick
31 1 904866 Height Adjustment Rod
32 2 204858
Spacer, Plastic, Biscuit
33 2* 204857 Spacer, Metal 1/2” O.D. x 1.44 Long
34 1 204853
Lanyard, Black Coil
35 1 204850 Pin, Locking
36 1 204803
Screw, Phillips Head
37 4 201124 Lock Nut, Hex, 3/8-16
38 1 204855
Handle, Left
Item Qty. Part No. Description
39 1 204856 Handle, Right
40 1 200118 Front Cover
41 1 204872 Label, Height Indicator
42 1 206219 Cap, Base-Black
43 1 203814 Label, Height and Moving
44 1 201568 Anchor Strap
45 1 204832 Bracket, Pole Mount
46 2 203053 Bolt, Carriage, 5/16-18 x 4 Long
47 1 206990 Reinforcement Bracket
48 2 204859 Cover
49 12 201219 Smart Clip, Net Holder
50 1 203038 Bolt, Carriage, 5/16-18 x 2.75" Long
51 2 201129 Spacer, Metal, .5 O.D. x .402 I.D. x 1.8 Long
52 2 900846 Board Bracket
53 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long
54 3 206360 Bolt, Hex Head, 3/8-16 x 2.625 Long
55 1 203493 Lock Nut, Hex Center-lock, 1/4-20
56 2 900183 Elevator Tube, Lower (Long)
57 6 204847 Bolt, Hex Head, 1/2-13 x 9-1/2 Long
58 7 206340 Lock Nut, 1/2-13
59 4 201682 Spacer, Black, .56 I.D. x .683 O.D. x 1.88 Long
60 4 201611 Bolt, Hex Flange, 5/16-18 x 3 Long
61 4 265601 Bolt, Carriage, 5/16-18 x 3-1/2 Long
62 4* 203309 Washer, Flat, 1" O.D.
63 2 904807 Elevator Tubes, Upper (Short)
64 1 207103 Pole Cap
65 1 201139 Bolt, Hex Head, 1/2-13 x 4-1/2 Long
66 2 900867 Triangle Plate
67 8 202862 Spacer, Plastic, 1/2 I.D., 1-1/4 Long
68 1 204837 Spring
69 1 Net
70 1 Rim
WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC
BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY
HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD
COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS
DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLLFREE NUMBER FOR FREE REPLACEMENT:
U.S. 1-800-558-5234; CANADA: 1-800-284-8339;
http://www.huffysports.com
*You may have extra parts
with this model
NOTE:
09/04 P/N 211574
5
HARDWARE IDENTIFIER (CONTINUED)
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #5 (1)
Item #21 (1)
Item #19 (1)
Item #65 (1)
Item #54 (3)
Item #23 (1)
Item #10 (1)
Item #36 (1)
Item #16 (1)
Item #60 (4)*
Item #14 (2)
Item #4 (1)
Item #57 (6)
Item #26 (6)
Item #50 (1)
Item #46 (2)
Item #61 (4)
Item #53 (1)
6
P/N 211574 09/04
*You may have extra parts with this model.
HARDWARE IDENTIFIER (NUTS & WASHERS)
HARDWARE IDENTIFIER (STEEL SPACERS, RODS & CLIPS)
HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS & CLIPS)
Item #37 (3)*
Item #55 (1)
Item #58 (7)
Item #51 (2)
Item #67 (8)
Item #49 (12)
Item #59 (4)
Item #20 (8)*
Item #11 (7)*
Item #15 (20)*
Item #8 (4)
Item #12 (1)
Item #13 (1)
Item #32 (2)
Item #33 (2)*
Item #29 (4)
Item #62 (4)*
09/04 P/N 211574
7
BEFORE YOU START!
To ensure optimal playability of backboard system, a close tolerance fit between the elevator
components and hardware is required. Test-fit large bolts into large holes of elevator tubes,
backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out
any excess paint from holes if necessary.
AVANT DE COMMENCER !
Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien
ajustés (serrés). À titre d'essai, insérez les gros boulons dans les gros trous des tubes du système élévateur, des supports
du panneau et des plaques triangulaires. Basculez-les avec précaution en imprimant un mouvement circulaire pour
éliminer l'excédent de peinture, si nécessaire.
¡ANTES DE COMENZAR!
Para asegurar el óptimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha
entre los componentes del elevador y el herraje. Pruebe el ajuste de los pernos grandes en los orificios grandes de los
tubos elevadores, soportes del respaldo y placas triangulares. Cuidadosamente muévalos en círculos para eliminar
cualquier exceso de pintura, si es necesario.
VORBEREITENDE MASSNAHMEN
Um sicherzustellen, dass das Korbwandsystem optimal für den Spielbetrieb geeignet ist, müssen die Komponenten der
Verlängerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Große Schrauben
zur Probe in die großen Löcher der Verlängerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese
vorsichtig in einer Kreisbewegung hin- und herbewegen, um eventuelle Farbrückstände aus den Bohrungen zu entfernen.
8
P/N 211574 09/04
1.
MIDDLE
2
3
1
Identify pole sections.
ID Sticker
ID Sticker
2.
WOOD SCRAP
(NOT SUPPLIED)
2
1
While maintaining alignment, bounce middle pole section (2) into top section (1)
using a wood scrap as shown until the top pole no longer moves toward the pole
identification sticker on the middle pole.
Align dimple of top pole section (1)
into trough of middle pole section (2)
as shown.
IMPORTANT!:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
MINIMUM OVERLAP.
NOTE:
HOLE
DIMPLE
middle pole
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 11/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
CAUTION!
5"
middle pole
1-1/2"
ID
STICKER
(13 cm)
TOP
5"
5"
(13 cm)
BOTTOM
TROUGH
09/04 P/N 211574
9
3.
1
2
3
WOOD SCRAP
(NOT SUPPLIED)
RODS SHOWN ARE
FOR VISUAL
REPRESENTATION
OF ALIGNMENT
AND ARE NOT
SUPPLIED WITH
THE HARDWARE
Align dimple of middle pole section (2)
into trough of bottom pole section (3)
as shown.
IMPORTANT!:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM)
MINIMUM OVERLAP.
NOTE:
HOLE
DIMPLE
Bottom pole
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 11/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
CAUTION!
5"
1-1/2"
ID
STICKER
Bottom pole
Bounce top and middle pole assembly (1 & 2) onto bottom pole section (3) using a
wood scrap as shown. Bounce until the top and middle pole assembly no longer
moves toward the pole identification mark on the bottom pole.
TROUGH
10
P/N 211574 09/04
4.
5.
Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15) as shown.
25
17
17
29
29
28
15
16
15
09/04 P/N 211574
11
6.
Install rod (4) through holes in bottom pole section (3) and eyebolt (5).
Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure
pole assembly with strap (44), washer (11) and lock nut (8).
5
4
1
3
2
8
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
8
4
5
11
44
12
P/N 211574 09/04
7.
9
9
Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown.
Rotate the non-secured ends of base struts (9)
as shown.
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
10
11
11
12
9
3
13
NOTE:
ORIENTATION OF STRUTS
09/04 P/N 211574
13
8.
9.
Secure base struts (9) to base using bolt (14) washers (11) and nut (15).
Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut (8) as shown.
14
11
15
11
9
8
20
18
19
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
14
P/N 211574 09/04
Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 13.
Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt (23), washers
(20) and lock nut (8) as shown.
Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and
flange nuts (15).
18
23
20
22
21
20
8
26
25
15
24
10.
11.
IMPORTANT!:
DO NOT OVER
TIGHTEN
IMPORTANT!:
WICHTIG!:
¡IMPORTANTE!:
NOTE ORIENTATION
NOTEZ L'ORIENTATION.
DIE KORREKTE AUSRICHTUNG BEACHTEN.
NOTE LA ORIENTACIÓN.
24
09/04 P/N 211574
15
Position base as shown. Secure wheel
bracket assembly with disc (30), washer
(20) and nut (8) as shown.
29
27
28
25
27
29
21
30
20
8
Carefully reposition entire
assembly as shown:
12.
13.
SIDE OF WHEEL WITH
LONGER PLASTIC
AXLE NEEDS TO FACE
THE WHEEL BRACKET.
IMPORTANT!:
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown.
IMPORTANT!:
DO NOT OVER
TIGHTEN
14.
16
P/N 211574 09/04
15.
Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolts
(46) as shown. Tighten flange nuts (15) completely.
16.
Attach spacers (32, 33) to pole mount bracket (45) with bolts (54), washers (20),
and lock nuts (37) as shown. IMPORTANT! Tighten just until washers (20) stop
moving.
45
20
20
37
54
20
20
33
32
32
33
46
46
1
45
15
15
47
09/04 P/N 211574
17
17.
45
15
35
48
48
34
50
Apply logo and height indicator labels (41) to
adjustment rod (31) as shown. Attach handle
parts (38, 39) to adjustment rod with screw
(36), carriage bolts (26), and flange nuts (15)
as shown.
18.
26
15
15
39
38
36
26
31
41
41
Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto
pole mount bracket (45) with carriage bolt (50) and nut (15) as shown.
50
FIG. A
34
35
Loop end of pin
lanyard (34) over
carriage bolt (50)
as it passes
through the pole
mount bracket
(45) during this
assembly.
IMPORTANT!:
Indicator labels
should be applied
as close to holes
as possible to
prevent labels from
being damaged
during height
adjustment.
IMPORTANT!:
FRONT
SIDE
18
P/N 211574 09/04
53
51
37
52
55
54
Insert handle assembly through pole mount assembly as
shown. Lock pole assembly in place at the 10’ (3.05 m)
mark with pin (35).
35
19.
20.
Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock
nuts (55, 37) as shown.
IMPORTANT!:
KEEP HARDWARE LOOSE
UNTIL AFTER STEP 25 IS
COMPLETED.
09/04 P/N 211574
19
58
59
57
56
52
21.
63
Upper Elevator tube
Toward
Pole
Toward
Board
56
Lower Elevator tube
Toward
Pole
Toward
Board
Identify elevator tubes (63 & 56).
Attach lower elevator tubes (56) and counter balance spring (68) to backboard
support brackets (52) using spacers (59), bolt (57), and nut (58) as shown.
56
59
68
20
P/N 211574 09/04
22.
52
15
15
70
60
62
68
23.
58
63
63
57
59
52
59
Starting with nuts (15) flush
against bracket (52) secure rim
(70) and bracket to backboard.
IMPORTANT! For spring
loaded rim assembly, refer
to instructions included with
rim hardware.
NOTE: Rim mounting nuts
and bolts supplied with rim
hardware.
NOTE: DO NOT use washers
here on spring return style
rims.
Attach upper elevator tubes (63) to backboard support brackets (52) using spacers
(59), bolt (57), and nut (58) as shown.
09/04 P/N 211574
21
58
58
65
64
56
1
66
66
57
67
56
67
24.
Support pole on sawhorse. Attach backboard assembly to top pole section (1)
as shown. Install pole cap (64). NOTE: Two people are recommended for this
step. Use caution; elevator assembly is heavy.
57
63
67
58
1
58
63
67
66
51
25.
Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle
assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as
shown.
NOTE: Before going on to next step, set adjustable system assembly to the 10’
(3.05 m) setting.
57
56
56
67
67
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
IMPORTANT!:
TIGHTEN ALL HARDW ARE
FROM STEP 20-25 AFTER
THIS ASSEMBLY IS
COMPLETED.
22
P/N 211574 09/04
26.
Insert bolt (57) through left side upper elevator tube (63), then stretch spring
(68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63)
and secure with nut (58).
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
WARNING!
57
63
58
68
63
09/04 P/N 211574
23
SECTION D: INSTALL FRONT COVER & HANDLE
27.
Attach front cover (40) to hinge tubes (18) using carriage bolts (51) and flange nuts (22)
as shown.
40
61
15
24
Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (42) in place.
42
28.
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
WARNING!
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUBFREEZING CLIMATES.
CAUTION!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
8
44
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT
REQUIRED
NOTE:
SAND
SAND
(360 lb.)
(360 lb.)
(163 kg)
(163 kg)
24
P/N 211574 09/04
29.
Roll assembly to desired playing area. Secure assembly
to ground using strap (44) and tie down stake (7).
44
7
8
30.
ELEVATOR HEIGHT ADJUSTMENT
35
A.
B.
C.
31
DO NOT ALLOW
CHILDREN TO
ADJUST HEIGHT.
WARNING!
31.
A. While holding handle, remove pin (35).
B. Move elevator up or down to desired height.
C. Replace pin (35) full length to lock system at
desired height.
Apply height and moving label
(43) to front of pole as
shown.
203814 03/04
MOVING SYSTEM
1. Adjust basketball backboard
height to lowest position.
2. Rotate handleforward until
wheels engage ground.
3. Move basketball system to
desired location.
4. Rotate handle back to original
position.
5. Reattach ground restraint and
check system for stability.
HEIGHT ADJUSTMENT
1
3
2
4
TO ADJUST BACKBOARD:
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
3. Replace pin full length to lock
system at desired height.
10 feet
(3.05m)
43
1
3
2
2
09/04 P/N 211574
25
WARNING:
Use of this product without proper installation
of net clips, or when all net clips are not present could result in
bodily harm. Be sure to follow directions carefully.
AVERTISSEMENT : L'utilisation de ce produit sans installer
correctement ou toutes les pinces du filet risque de causer des
blessures. Veillez à suivre scrupuleusement les instructions.
WARNUNG: Ein Gebrauch dieses Produkts ohne ordnungsgemäß
angebrachte Netzhalteklammern bzw. ohne den Gebrauch der
Netzhalteklammern kann Verletzungen nach sich ziehen. Die Anleitung
genau befolgen.
ADVERTENCIA: Si este producto se usa con los sujetadores de la red
incorrectamente instalados, o si no están todos presentes, se pueden
ocasionar lesiones corporales. Asegúrese de seguir cuidadosamente
las instrucciones.
Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red.
CLIP “ARM”
" BRAS " DE LA
PINCE
CLIP-ARM
"BRAZO" DEL
SUJETADOR
CLIP “BODY”
" CORPS " DE LA PINCE
CLIP-HAUPTTEIL
"CUERPO" DEL
SUJETADOR
Insert one “arm” of clip (70) into ram (49) as shown. Twist “body” of clip slightly so that second “arm”
slides over the top of the first “arm” as shown.
Push in direction indicated by arrows.
Insérez un " bras " de la pince (70) dans l'éperon (49), comme illustré. Tournez légèrement le corps de la
pince de sorte que le second bras glisse par-dessus le premier, comme illustré.
Einen Arm des Clips (70) wie gezeigt in die Spirale (49) einsetzen. Den Hauptteil des Clips etwas drehen,
sodass der zweite Arm wie gezeigt oben über den ersten Arm geschoben werden kann.
Introduzca un "brazo" del sujetador (70) en el accionador (49) como se muestra. Tuerza ligeramente el
"cuerpo" del sujetador de manera que el segundo "brazo" se deslice sobre el primer "brazo" como se
muestra.
Push second “arm” back and into ram as shown.
Poussez dans le sens des flèches.
In die durch die Pfeile angezeigte Richtung schieben.
Empuje hacia la dirección que indican las flechas.
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as shown, not overlapping.
Tournez légèrement le corps de la pince une nouvelle fois pour en étaler les bras.
Den Hauptteil des Clips noch einmal leicht drehen, um die Arme des Clips zu spreizen.
Otra vez tuerza ligeramente el "cuerpo" del sujetador para abrir los "brazos" del
sujetador.
AA
BB
CC
32
70
49
26
P/N 211574 09/04
Install net.
Installez le filet.
Das Netz anbringen
Instale la red.
Insert net into bottom of clip as shown.
Insérez le filet dans la base de la pince, comme illustré.
Das Netz wie gezeigt unten in den Clip stecken.
Introduzca la red en la parte inferior del sujetador como se muestra.
SIDE VIEW
VUE DE CÔTÉ
SEITENANSICHT
VISTA LATERAL
Twist net until it snaps into position.
Net must be centered through clip.
Tournez le filet jusqu'à ce qu'il s'enclenche en position.
Das Netz drehen, bis es einschnappt.
Tuerza la red hasta que quede conectada en su posición.
Le filet doit être centré dans la pince.
Das Netz muss im Clip zentriert werden.
La red debe quedar centrada a través del sujetador.
NET
FILET
NETZ
RED
NETCLIP
PINCE DE FILET
NETZHALTEKLAMMER
SUJETADOR DE LA RED
33.
70
49
69
SIDE VIEW
VUE DE CÔTÉ
SEITENANSICHT
VISTA LATERAL
NET
FILET
NETZ
RED
NETCLIP
PINCE DE FILET
NETZHALTEKLAMMER
SUJETADOR DE LA RED
Loading...