Huffy 89226 User Manual
1
P/N 21155402 09/04
IMPORTANT!
To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and
Display Technician at 1-800-558-5234.
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
WARNING!
Display System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Model
89226
7/16"
REQUIRED TOOLS AND MATERIALS:
• 2 People
• 2 Stepladders
• Phillips Screwdriver
• (2 each) Wrenches and/or
Socket Wrenches and
Sockets.
1/2" 9/16"
7/16" 1/2" 9/16"
AND/OR
P/N 21155402 09/04
2
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to the instructions. Failure to follow instructions
could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
• During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
• If technical assistance is required, contact Huffy Sports’ Sample and
Display Technician.
• Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
• Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
• All instructions and warnings MUST accompany any display item
that is sold.
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
3
P/N 21155402 09/04
PARTS LIST (See Hardware Identifier)
Item #17 (2)
HARDWARE IDENTIFIER (NUTS, WASHERS & SPRINGS)
Item #9 (12)
Item #11 (12)
Item Qty. Part No. Description
1 3 200318 Bracket, Reinforcement S/J
2 1 200503 P/S Cover
3 2 200520 Screw, #8 x 3/4", Flat Hd, Phillips
4 2 200533 Spacer, Mounting
5 48 201219 Net Clips
6 3 201344 Plastic Knob
7 12 201611 Bolt,Hex-Flange, 5/16-18 x 3"
8 1 202795 NBA Sticker
9 12 203063 Locknut, 3/8-16 Nylon Insert
10 1 203157 Bolt, Carriage, 5/16-18 x 2.25"
11 12 203100 Nut, Hex-Flange 5/16-18 Whiz Lock
12 2 203231 Bolt, Carriage, 5/16-18 x 3.5"
13 6 203294 Bolt, U, Round, 3/8-16 x 3.5"
14 4 203309 Washer
15 2 203470 Washer, Flat, S/J
16 2 203472 Spring
17 2 203795 Nut, 3/8-16 Special S/J
18 2 203796 T-bolt, 3/8-16 x 5"
Item Qty. Part No. Description
19 7 203798 Bolt, Hex 5/16-18 x 1.5"
20 4 204290 Net
21 1 206219 Pole Cap, 3"
22 3 207103 Pole Cap, 3.5"
23 2 900033 Bracket, S/J
24 1 900060 Pole, 3"
25 4 Rim
26 1 900253 Bracket, Pole Mount, No Tools
27 7 206987 Wedge
28 1 909256 Board, 48", Fan, Viper
29 1 909259 Board, 44", Fan, Evolution, NT
30 1 909602 Board, 44", Fan, Zone Attack
31 3 912006 Extension Arm
32 1 939235 Board, 48", SFA, Titanium II
33 3 990062 Pole, 3.5"
34 1 204516 Pole Sleeve
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #19 (7)
Item #7 (1)
Item #12 (2)
Item #10 (1)
Item #18 (2)
Item #3 (2)
Item #16 (2)
Item #15 (2)
Item #14 (4)
P/N 21155402 09/04
4
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with
the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is
facing).
Corner “2”
73256
Corner “4”
80602
Corner “3”
61259
Corner “1”
9H235A
Display boards will be mounted as follows:
Corner Location 1: 9H235A
• 48” SFABoard
• Titanium II Logo
• Black Slam Jam Goal with Cover
• Use extension arm for assembly
Corner Location 2: 73256
• 48” Fan Recycled Board
• Viper Logo
• Black Slam Jam Goal
• Use extension arm for assembly
Corner Location 3: 61259
• 44” Fan Recycled Board
• Evolution Logo
• Black Standard Goal
• No Tools, E3 Elevator System
Corner Location 4: 80602
• 44” Fan Recycled Board
• Zone Attack Logo
• Black Standard Goal
• Use extension arm for assembly
Display Stand - Top View
3-1/2"
3"
3-1/2"
3-1/2"
Loading...