Hubbell LMC Installation Instructions Manual

LAREDO LMC LED INSTALLATION INSTRUCTIONS (PG 1/2)

STEP I

MOUNTING PREPARATION

wall.

NOTE: DO NOT OPEN THIS PRODUCT UNLESS INSTRUCTED BY STEPS INCLUDED IN

SAVE THESE INSTRUCTIONS

WARNING!

WARNING!

do so may increase the
cause a hazard and use only in environments for which the product is specifically marked.

WARNING!

harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION!

regarding lumninaire operation, burning position, cycling and lamp replacement. Luminaire label shows electrical and environmental
requirements.

All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting

with a soft, clean, dry cloth is normally sufficient for the optical assembly. Any accumulation of dust or dirt should be removed regularly.

Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact
your Hubbell Lighting distributor or [e-mail] or [phone]

Give instructions to facility owner/manager for future reference.

LUMINAIRES require high current and voltage.

Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to

RISK OF PERSONAL INJURY, PROPERTY DAMAGE, FIRE AND DEATH.

This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive

Follow ALL luminaire manufacturer's recommendations, product markings, instructions, restrictions and warnings

Install and use so product does not

THESE INSTRUCTIONS OR BY HUBBELL LIGHTING TECHNICAL SUPPORT PERSONNEL.
FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL MOUNTING BRACKETS.

TOOLS REQUIRED: FLAT BLADE SCREWDRIVER OR 5/16” NUT DRIVER, DRILL, ANY
ADDITIONAL TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS

PARTS REQUIRED: (SUPPLIED BY OTHERS) SILICONE CAULK, 1/4” WALL ANCHORS
AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE

CAUTION: SHOCK HAZARD! IF YOUR PRODUCT IS EQUIPPED WITH A –BOC OPTION, DO
NOT CONNECT BATTERY BACKUP RED AND WHITE WIRES UNTIL INSTRUCTED TO IN
THESE INSTRUCTIONS (SEE STEP III)

CAULKING

CAUTION: FIXTURE WEIGHS ABOUT 15 POUNDS

• Using mounting bracket (A) as a template, align slots in
bracket with mounting holes in junction box (B) on the

Mark hole locations (4) 4.5” square. (See Fig.1)

• Drill wall for the hardware appropriate for the type wall.
Use 1/4 diameter bolt (supplied by others) and attach
bracket to wall.

• Pull the supply wires (C) from junction box (B).

• Apply caulking sealant (supplied by others) around the
top and two sides of the bracket where it meets the wall.

4.500

4.500

C

B

A

FIG. 1

93029166 Rev C - Page 1 of 2

701 Millennium Boulevard Greenville, SC 29607 [phone]

www.hubbelloutdoor.com

LAREDO LMC LED INSTALLATION INSTRUCTIONS (PG 2/2)

STEP I

II FIXTURE MOUNTING

(See Fig.

3)

Step

II WIRING

(See Fig.

2)

• Luminaire is equipped with a universal voltage driver capable of

wire. Connect

product per the supplemental Battery Backup Installation

NOTE: DO NOT OPEN THIS PRODUCT UNLESS INSTRUCTED BY STEPS INCLUDED IN

SAVE THESE INSTRUCTIONS

THESE INSTRUCTIONS OR BY HUBBELL LIGHTING TECHNICAL SUPPORT PERSONNEL.
FIXTURE HAS BEEN DESIGNED WITH EASY TO INSTALL MOUNTING BRACKETS.

POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY A QUALIFIED

ELECTRICIAN)
CAUTION! SHOCK HAZARD, DO NOT CONNECT RED AND

WHITE WIRES TOGETHER UNTIL ALL OTHER
CONNECTIONS HAVE BEEN MADE.

• Wire service leads to fixture power leads according to local
and National Electric Codes.

120V-277V input.

• For direct wire connections, connect ground wire to green
black to black and white to neutral then push

connections back inside J-box.

⊕ For –BOC equipped product, make connections to

FIG. 2

A

B

Instructions included with the fixture.

• Hold fixture at a slight angle, slide over mounting plate and
rotate downward to capture plate.

• Tighten screw (G) securely.

• Check to ensure secure mount.
⊕ For –BOC equipped product, open the door frame

by loosening door frame closure screws and allow
the door to swing open. Locate RED and WHITE
leads for inverter connector located at front fixture.
Connect red and white wires located inside door.

⊕ Close door frame by swinging back into position

ensuring wires are not pinched under door mounted
reflector. Tighten door frame screws until snug.

• Energize product.

FIG. 3

93029166 Rev C - Page 2 of 2

701 Millennium Boulevard Greenville, SC 29607 [phone]

G

www.hubbelloutdoor.com