Hubbell Laredo Installation Instructions Manual

STEP I

MOUNTING PREPARATION

CAUTION: FIXTURE WEIGHTS ABOUT 30 POUNDS

• Using template (A) lay over junction box (B) on the wall.
Mark at (3) hole. (See Fig.1)

• Drill wall for the hardware appropriate for the type wall.
Use 1/4 diameter bolt.

• Pull the supply wires (C) from junction box (B) .

STEP II

FIXTURE MOUNTING PREPARATION

(See Fig. 2)

• To open door (E), loosen (2) retaining screws (F).

• For optional quick release door latch, push pin (D) to open
door (E).

• Loosen (4) screws (X) and them remove reflector (H).

• Loosen screws (O), remove cover (P) and discard.

STEP III

FIXTURE MOUNTING

(See Fig.3)

• Insert all wires (C) through slit on gasket opening at the
back of housing.

• Hang fixture on the mounting hardware at the wall through
key-slots opening (J).

• Tighten bolts (K) securely.

• Apply caulking sealant around the top and two sides of the
housing.

Step IV

WIRING

(See Fig. 3)

• POWER MUST BE OFF.
(WIRING MUST BE PERFORMED BY
A QUALIFIED ELECTRICIAN)

• Wire service leads to fixture power leads according to local
and National Electric Codes.

• For direct wire connections, connect ground wire to green
wire then push ware back to J-box on the wall. Connect
black to black and white to neutral then push connections
back inside J-box (B).

• When supplied with optional terminal block (L) or fuseblock
(M) connect service leads to these devices.

FOR THROUGH WIRING USING CONDUIT

• Remove hole plug (N) for the conduit entry

• Use pipe sealant before engaging conduit fittings to prevent
water leakage.

• Loosen screw (O) and remove wire cover (P).

• Insert fixture lead wires (Q) through grommet ( R ).

• Make the wire connections.

• Replace cover (P) making sure not to pinch wires.

INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE

laredo

WARNING: DISCONNECT POWER BEFORE INSTALLATION OR MAINTENANCE.
READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL
LUMINAIRE, FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE.

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

Outdoor Lighting

STEP V

LAMPING

• Make sure that the lamp size and type matches the ballast
specifications.

• Replace reflector (H).

• Engage the lamp to socket (S).

• For medium base lamps – to ensure proper contact, loosen
the lamp one turn then retighten.

STEP VI

RE-LAMPING USING POLE STICK

(By others)
(See Fig.4)
CAUTION:
WEAR SAFETY GOGGLES IN THE EVENT LAMP BREAKS

• Using the other end of the pole, push latch pin (D) and

slowly lower the door to open position.

• Align lamp changer (U) with the lamp, then slowly push up

to engage. Unscrew to remove lamp.

• Attach the replacement lamp to head changer (U), align

with the socket and screw in to engage.

• To close door use again the other end of the pole, raise the

front end of the door up to engage latch.

REMOVING FRONT DIRECTOR FOR IMPROVING
FORWARD THROW BEAM DISTRIBUTION.

• Loosen (4) retaining screws (X) and remove reflector (H).

• Unbend the two tabs to remove the front director (Z).

STEP VII

INSTALLING VANDAL SHIELD

(See Fig. 5)

• Open door (E) by loosening retaining screws (F).

• From the inside on each (4) bosses adjacent to the lens

clips, drill the door through using .173” diameter No.17 drill
bit.

• Install vandal shield (Y) using (4) self-threading screws (V)

provided.

• Remove metal chips and replace door.

STEP VIII

PBT PHOTOCONTROL FIELD INSTALLATION

(See Fig. 6)

• Remove hole plug (N) from the side of housing.

• Install photocontrol switch (PC) from the inside of housing

using gasket (gg) and nut (nn).

PT. NO. 93002010

laredo

INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE

Outdoor Lighting