Huawei PT500 User Manual

PT500 500Mbps Powerline Adapter

User Guide

PT500 500Mbps Powerline Adapter

V100R001

User Guide

202593_04

Huawei Technologies Co., Ltd. provides customers with comprehensive technical

support and ser vice. Please feel free to c ontact our local office or company

headquarters.

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email:

[e-mail]

i

Copyright © Huawei Technologies Co., Ltd. 2013. All rights
reserved.

No part of this document may be reproduced or transmitted in any for m or by any means

without prior written consent of Huawei Technologies Co., Ltd.

The product described in this manual may include copyrighted software of Huawei

Technologies Co., Ltd and possible licensors. Customers shall not in any manner

reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer,

lease, assign, or sublicense the said software, unless such restrictions are prohibited by

applicable laws or such actions are approved by respective copyright holders under

licenses.

Trademarks and Permissions

、 、and are trademarks or registered trademarks of

Huawei Technologies Co., Ltd.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC in the United States and other

countries.

Other trademarks, product, service and company names mentioned are the

proper ty of their resp ective owners .

Notice

Some features of the product and it s accessories described herein rely on the software

installed, capacities and settings of local network, and may not be activated or may be

limited by local network operators or network service providers. Thus the descriptions

herein may not exactly match the product or its accessories you purchase.

Huawei Technologies Co., Ltd reserves the right to change or modify any information or

specifications contained in this manual without prior notice or obligation.

DISCLAIMER

ALL CONTENTS OF THIS MANUAL ARE PROVIDED “AS IS”. EXCEPT AS REQUIRED

BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR

ii

IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN

RELATION TO THE ACCURACY, RELIABILITY OR CONTENT S OF THIS MANUAL.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT

SHALL HUAWEI BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES, OR LOSS OF PROFITS, BUSINESS, REVENUE, DATA,

GOODWILL SAVINGS OR ANTICIPATED SAVINGS REGARDLESS OF WHETHER

SUCH LOSSES ARE FORSEEABLE OR NOT.

THE MAXIMUM LIABILITY (THIS LIMITATION SHALL NOT APPLY TO LIABILITY FOR

PERSONAL INJURY TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH A

LIMITATION) OF HUAWEI ARISING FROM THE USE OF T HE PRODUCT DESCRIBED

IN THIS MANUAL SHALL BE LIMITED TO THE AMOUNT PAID BY CUSTOMERS FOR

THE PURCHASE OF THIS PRODUCT.

Import and Export Regulations

Customers shall comply with all applicable export or import laws and regulations and will

obtain all necessary governmental permits and licenses in order to e xport, re-export or

import the product mentioned in this manual including the software and technical data

therein.

Privacy Policy

To better understand how we protect your personal information, please see the privacy

policy at http://consumer.huawei.com/en/privacy-policy/index.htm.

iii

Contents

1 About PT500 ......................................................... 1

2 PT500 Installation ................................................. 4

3 Advanced Configuration ...................................... 6

4 Tab Pages on the PCU User Interface................ 12

5 FAQs ................................................................... 16

6 Technical Specifications .................................... 18

iv

1 About PT500

Functions

The state of the art, plug and play PT 500 power line adapter enables fast communication

on your existing home power line network without e xtra routing. With the PT500, the

power line serves as a network cable and the power socket serves as a network adapter.

You can connect to your network directly by connecting the PT500 to a power socket. The

PT500 is sleek and convenient, and can transmit data to a 300-meter distance at a rate of

200 Mbit/s on the power line network.

Figure 1-1 shows home network setup using the PT500.

Figure 1-1 Home network setup using the PT500

Description:

1 PT500 2 Internet

3 Router 4 Set-top box (STB)

Pictures shown in this document are only for your reference.

1

Butto ns

Figure 1-2 shows the buttons on the PT500 shell.

Figure 1-2 Buttons on the PT500 shell

Table 1-1 describes the buttons on the PT500.

Table 1-1 Buttons on the PT500

Button Description

Pair Button Connects the PT500 to a safety network or restores the PT500

to its default settings.

Press and hold the Pair button on a PT500 (no more than 4

seconds), and repeat the operation on the other PT500 within

2 minutes. The two adapters are then connected and a LAN is

set up. After paired successfully, the two PT500 can be

plugged in or out at any time and you don’t need to pair them

again.

The PT500 is restored to its default se ttings when you push

and hold the Reset button for 8 seconds in running mode.

AC power plug Can be plugged into a power socket.

Network Port Connects the PT500 to a network device.

2

Indicators

Indicator

Status

Description

Figure 1-3 shows the indicators on the PT500 panel.

Figure 1-3 Indicators on the PT500 panel

Table 1-2 describes the indicators on the PT500 panel.

Table 1-2 Indicators on the PT500 panel

PWR Steady on The PT500 is running.

Flicker The PT500 is running in energy saving mode.

Off The PT500 is powered off.

LAN Steady on T he PT500 is connected to the network.

Off The PT500 is not connected to the network or is running in

energy saving mode.

PLC Steady on T he PT500 is connected to a device of the same type.

Blinks The PT500 is searching for a network.

Off The PT500 is not connected to the network or is running in

energy saving mode.

3

2 PT500 Installation

Network cables and power line adapters are required if you want to use power lines to

connect terminal devices to a LAN.

Connec ting the Ha rdware

Figure 2-1 shows how to use the power line adapter to set up a network.

Figure 2-1 Using the power line adapter to set up a network

1. Use a network cable to connect a PT500 and network device, such as a

gateway.

2. Connect the PT500 to a power socket. T he PWR indicator turns steady on.

3. Use another network cable to connect the other PT500 and an STB or othe r

terminal devices.

Connect the second PT500 to another power socket. T he PWR indicator turns

steady on.

One PT500 is required to add each terminal device to the network.

Number of required PT500 adapters = Number of terminal devices + 1

4

Setting up a Netw ork Quickly

The PT500 supports the 128-bit Advanced Encryption Standard (AES). You can use the

Pair button to quickly set up a network with multiple PT500 adapters to ensure secure

data transmission.

To quickly set up a network with multiple PT500 adapters:

1. Press and hold the Pair button on a PT 500 no more than 4 seconds, and then

release it.

The PWR indicator starts to blink.

2. Within 2 minutes, press and hold the Pair button on the other PT500 for 4

seconds, and then release it.

The PWR indicator starts to blink.

3. View the indicator status. When all indicators turn off and then steady on, a LAN

is then set up.

4. Press and hold the Pair button on a PT500 not connected to the LAN for 4

seconds, and then release it. Within 2 minutes, press and hold the Pair button

on any PT500 already connected to the LAN, and then release it.

The indicators on the newly connected PT500 turn off and then steady on. The

PT500 automatically restarts and is connected to the network.

A home network supports a maximum of eight PT500 adapters.

If the PLC indicator didn't blink after you press the Pair button, then please

plug the PT500 into the socket again and repeat this operatio n until the

indicator blinks.

If the pairing process fail for several attempts, press and hold PT500's PAIR

button more than 8 seconds until the PWR indicator turns off and then

release it. When the PWR indicator lights up again, repeat the pairing

process.

5

3 Advanced Configuration

The PCU（PT500 Configuration Utility） software is used to manage the power line

adapters. This software can scan and manage all devices on a private network and

display information about devices with the same network membership key. You can go to

http://consumer.huawei.com/en to download the product configuration software.

The PCU software is required only when you use the advanced PT500

applications.

Configuring a Private Network

To implement power line communication, connect at least on e pair of PT 500 adapters. A

power line network can be divided by network names. Each PT500 powerline adapter is

preset with a network name. PT500 powerline adapters with the same network name can

connect to each other in the sa me power line network. If multiple PT500 powerline

adapters are in the power line network, you can create a private network by changing the

PT500 network names. This also improves data transmission security.

After you connect them using network cables and making sure there is at least a PC in

your network, install the PT500 configuration utility (PCU) software to configure your

private network, such as home network or working network.

Figure 3-1 shows PT500’s network.

Figure 3-1 PT500’s network

6

To configure your private network:

1. Check that the PWR indicator on the PT500 is steady on.

2. Install PCU software.

Please run PCU software in Windows XP, Windows Vista or Windows 7.

3. After the setup is complete, running the PT500 Configuration Utility software

, the PT500 Configuration Utility window is displayed, as shown in

Figure 3-2:

Figure 3-2 PT500 Configuration Utility window

7

4. Click a device (such as 500Mbps Powe rline Adapter) to configure the device,

as shown in Figure 3-3.

Figure 3-3 Search results

1) On the Main tab page, click Connect.

8

The system displays the information about all devices on the LAN, such

as the device name, model, and software version in the Remote Device

area.

2) Click Device 2.

Click Enter Password to enter device’s password.

5. Display the Network Name tab page to configure the network shown in Figure

3-4.

Figure 3-4 Network Name tab page

1) Enter a name for the private network in the Network Name text box.

2) Click Set All Devices.

All devices will restart to set up a private LAN with all device passwords

registered to the local device.

You can click Default Public Ne twork Name to retrieve a default network

name, and then click Set All Devices to release the private LAN to set up a

public LAN.

9

Update the PT500 Firmw are

1) On the Main tab page, click Upgrade Firmw are.

The Enter PIB & NVM files dialog box is displayed, as shown in Figure 3-5.

Figure 3-5 Enter PIB & NVM files dialog box

2) In the Enter PIB & NVM files dialog box, click Browse to specify the path

for storing the PIB and NVM.

3) Click OK.

The files are loaded.

You can download the latest update files from the technical support Web site:

http://www.huaweidevice.com.

Restoring Defau lt Sett ings

Be careful all self-defined data will be lost when you use this function.

10

To restore the PT500 to its default settings, press and hold the Pair button for 6 seconds

after it is powered on.

11

4 Tab Pages on the PCU User Interface

For more information about the PCU software functions, please refer to the following

details.

Main Tab Page

Main Tab Page includes two areas. The Local Device area shows the information of

device which connects your current PC and the Re mote Device area show the

information of other device which in your network.

Figure 4-1 shows the Main tab page.

Figure 4-1 Main tab page

Table 4-1 describes the buttons on the Main tab page.

Table 4-1 Buttons on the Main tab page

Button Description

Connect Connect to the specified remote device.

Upgrade Firmware Upgrade the firmware.

Reboot Restart a specified device.

Restore Default Restore a specified device to default settings.

Rename Rename a specified device.

12

Enter Password Set password for a specified device. When you manage a

remote power line adapter through the PCU software, you

must match the password first.

Add New Device Add a device.

Netw ork Name Tab Page

Figure 4-2 shows the Netw ork Name tab page.

Figure 4-2 Privacy tab page

To rename a private network, display the Netw ork Name tab page on the PCU, enter a

new name in the Ne twork Name text box, and click Se t All Devices. All devices will

restart to set up a private L AN.

Diagnostics Tab Page

Figure 4-3 shows the Diagnostics tab page.

Figure 4-3 Diagnostics tab page

13

The Diagnostics tab page displays the information about the system and remote

devices.

The System Information area displays the system information.

The Remote Device History area displays the remote device information.

About Tab P age

Figure 4-4 shows the About tab page.

Figure 4-4 About tab page

14

The About tab page displays the PCU software information, such as the version and

release date.

15

5 FAQs

What Can I Do If the PWR Indica tor Is Off

To resolve this problem:

1. Check that the PT500 is correctly connected to the power socket.

2. Check whether the power socket is faulty. If yes, replace it or find a nother.

3. If the PWR indicator is still off but other in dicators are normal, consult your local

Internet service provider (ISP) for help.

What Can I Do If the LAN Indicator Is Off

To resolve this problem:

1. Check whether the PT500 is connected to the network port.

2. Check whether the network adapter and driver are running properly and the

configured parameters are correct.

3. Check whether the co mputer can assess the Internet after you connect it to the

LAN port of the router.

4. Connect the PT500 to another LAN port of the router.

5. If the LAN indicator is still off, consult your local ISP for help.

What Can I Do If the PLC Indic at or Is Off

If the PLC indicator didn't blink after you press the Pair button, the device may be running

in energy saving mode. Please plug the PT500 into the socket again and repeat this

operation until the indicator blinks.

What Can I Do If the PT500 Fails to Connect to the Network

To resolve this problem:

1. Plug the PT500 into the socket again.

2. Press and hold PT500's PAIR button more than 8 seconds until the PWR

indicator turns off and then release it. When the PWR in dicator lights up again,

repeat the pairing process.

16

3. Press and hold the Pair button on a PT500 more than 1 second and less than 4

seconds, and repeat the operation on the other PT500 within 2 minutes.

4. If the PLC indicators are still off, consult your local ISP for help.

Can I Connect Multiple PT500 Adapters

A home network supports a maximum of eight PT500 adapters. To connect multiple

adapters to a home network, repeat the operation of connecting two PT 500 adapters.

17

6 Technical Specifications

Item Specifications

Power supply 100V ~240V AC, 50/60Hz

Power consumption < 3W

Working temperature 0℃～40℃

Working humidity 5% ~ 95% RH (non-condensing)

Dimensions (H x W x D) CN: About 71 mm × 62 mm × 48 mm

UK: About 71 mm × 62 m m × 57 mm

UL: About 71 mm × 62 mm × 49 mm

EU: About 71 mm × 62 mm × 64 mm

Weight CN: About 80 g (single piece)

UK: About 86 g (single piece)

UL: About 81 g (single piece)

EU: About 85 g (single piece)

18