Huawei ETS2207 User Manual

Packing List

The FWT package box contains the following items. Check the items according to the following table. If any of the items is missing or damaged, contact your local dealer.

Item	Quantity	Item	Quantity
Main unit, handset, and	1	Battery	1
coiled cord
Power adapter	1	Antenna (optional)	1

FWT User Guide	1	Certificate of Quality	1

Front View of the FWT

No.		Item		Function
1	Display screen			Displays the current operation of the FWT

2	SET/OK key		Set and save various functions
3	RECEIVED/▲ key			Access Call In in standby mode

4	CANCEL key			Delete queried information
5	DIALLED/▼key			Access Call Out in standby mode

6	Call/Redial key			Dial the telephone number on the screen
				Answer the call when there is an incoming call

7	HAND-FREE key			Make a call or receive an incoming call without lifting the
				handset
				handset

No.	Item	Function
8	End key	End or reject a call
		End the current operation when setting parameters
		Press and hold it to switch on/off the FWT

Back View and Side View

No.	Item	No.	Item
1	Antenna jack	2	Power jack
3	Data port	4	Coiled cord jack on main unit

5	Battery container cover	6	Hook

Screen Icons

NO.		Item	Description
1			Indicates the signal strength. The more the bars are, the
			stronger the signal is.
2			Indicates that you are in the hands-free mode of the FWT.
			Indicates that there is an incoming call or a call is ongoing.
3

4			Indicates that the FWT is powered by the power adapter.
			Indicates that there is a missed call.
5			Indicates that there is a missed call.

6			Indicates the battery power level.
6			Indicates the battery power level.

7	Month/Day/Time		Indicates the current date and time. If the FWT does not find
			the network, this information is not displayed.

NO.	Item	Description
8	Call duration	Indicates the call duration of the current call.

9	Missed calls	Indicates the number of missed calls.

Installing UIM Card (Optional)

Caution:

yWhether an UIM card is needed, consult your service provider for details.

yThe UIM card and its golden contact can be easily damaged by scratch or bending. Thus, be careful when installing or removing the UIM card.

After power off the FWT and disconnect the power, install or remove the UIM card. Make sure that the golden contact of the UIM card is facing downwards.

Installing the Battery

Note:

yThe FWT can be powered by the power adapter or the battery.

yBefore replacing the battery, disconnect the outdoor antenna.

yWhen the FWT installed with the battery is powered by the power adapter, the battery is auto charged. After the battery is fully charged, the charging stops.

yBefore using the battery for the first time, charge the battery for at least eight hours. When the battery is fully charged but not used for a long time, charge it for five minutes before you can use it again normally.

After power off the FWT and disconnect the power, install the battery. When installing the battery, make sure the battery cord plug matches the battery jack. Do not insert conversely.

Installing the Antenna

Note:

For details of antenna selection and installation, consult your local dealer.

Power off the FWT. Then connect the indoor antenna with the antenna jack on the main unit. Screw the antenna to make sure that the antenna is tightly connected with the antenna jack.

Placing the FWT

Horizontally

Place the FWT on the flat surface. Select a cool and ventilated site to dissipate heat.

Vertically

1.Pull out the handset retaining clip from the slot turn it around and then push it back so that the handset will not fall down when the FWT is placed vertically.

2.According to the distance between the two hooks (7.7 cm), hammer two nails into the wall with a 3 mm end left outside.

3.Snap the hooks to the nails.

Validating

You can make a call to check whether the FWT is correctly installed.

1.Press and hold to power on the FWT. After connecting the FWT with the external power supply, the icon appears, indicating that the FWT is powered normally.