HRS HR30 Service Manual
1
Miniature Waterproof Plastic Connectors
HR30 Series
NEW
2004.6
■Features
1. Small size
Short in length when fully terminated and mated.
2. Water and dust protected
IP67 protection rating: Complete protection against dust
penetration and against water penetration when
submerged 1 meter deep for half hour. Mated with
corresponding connector or protective cap.
3. Simple pull lock release
Built-in lock/release mechanism securely locks mated
connectors while allowing quick disconnection by simply
pulling on the plug’s release collar. Molded-in grooves
prevent hand slippage when pulled.
The round configuration of the collar allows easy side-byside panel mounting and will not snag on objects when
the cable is pulled-out.
4. Light weight, corrosion resistant
Glass reinforced thermoplastic compounds and noncorrosive components are used in all assemblies.
5. Contact protection and self- alignment
Multiple polarizing keys protect the contacts from missalignment or attempted insertion of the wrong connector,
while assuring correct mating between the corresponding
connectors.
6. Visual alignment indicators
Permanent alignment indicators in a contrasting color on
all connectors aid in correct alignment and engagement.
7. Built-in cable strain relief
■Applications
Test and measuring equipment, portable devices,
instrumentation, industrial devices, recreational equipment,
I/O applications and other applications requiring use of
lightweight, corrosion resistant quick mate/ release cable
connections.
Push-pull- single action lock
Ø15.5
42.1
Ø12.6
32.3
3 and 6 pos.
10 and 12 pos.
Mated dimensions
Lock/release operation
Alignment marks
Polarized interface
Push-pull locking collar
查询HR30-6J-10P供应商
2
■Product Specifications
■Material
Ratings
Current rating
Voltage rating
5A (3 pos.)
2A (6,10,12 pos.)
100V AC,140V DC(3,6 pos.)
30V AC,42V DC(10,12 pos.)
-25
ç to
+
85ç
-25
ç to
+
85
ç
Operation Temperature Range
StorageTemperature Range
1000M ohms min.
No flashover or insulation breakdown
Insulation resistance 100 M ohms min.
No penetration inside.
Insulation resistance
10M ohms min. (when humidity high)
100M ohms min. (when dry)
Contact resistance 10m ohms min.(3 pos.)
Contact resistance 30m ohms min. (Solder type: 6, 10, and 12 pos.)
Contact resistance 100m ohms min. (Through hole type: 6 and 12 pos.)
No electrical discontinuity of 10 µs or more
5m ohms max. (3 pos.)
15m ohms max. (Solder type: 6, 10, and 12 pos.)
30m ohms max. (Through hole type: 6 and 12 pos.)
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm,
2 hours in each of the 3 directions
1A DC
100 V DC
300 V AC / one minute
1000 cycles
96 hours at temperature of 40ohmsC and humidity of 90% to 95%
1.Contact resistance
2.
Insulation resistance
3.
Withstanding voltage
4.Vibration
5.
Durability (mating/un-mating)
6.Temperature cycle
7.Humidity resistance
8.
Waterproof performance
9.Dust protection
Characteristic ConditionsSpecification
Remarks
UL94V-0
UL94V-0
----------
----------
----------
----------
UL94V-0
----------
----------
----------
----------
----------
Material
PPS
PBT
Polyacetal
Silicone rubber, chloroprene rubber
Brass, phosphor bronze
Stainless steel
PPS
Chloroprene rubber
Brass, phosphor bronze
Zinc alloy
Phosphor bronze
Phosphor bronze
Finish Assembly Component
Plug
Insulator
Gasket
Contacts
Spring
Insulator
Gasket
Contacts
Hexagonal nut
Washer
Contacts
Receptacles
Crimp contact
(male/female)
Black
Black
Natural
Red/Black
Gold plated
----------
Black
Black
Gold plated
Chromate
Nickel plated
Selective gold plated
■Ordering information
HR 3 0 - 6 P A - 6 S C
1 52 3 4 6 7
Series name : HR30
1
Number of Contacts : 3, 6, 10 and 12
Contact type S : Female contact
P : Male contact
Contact wiring type
Blank : Solder
C : Crimping
D : Through hole
5
6
7
2
3
4
Shell size :
Outside diameter/plug mating side
Connector type : P : Plug
Connector type : R : Receptacle
Connector type : J : Jack
Variation
Blank : Standard
A : Fine wire
(-55ç: 30 minutes →Room temperature: 10 to 15 minutes →+85ç: 30
minutes →Room temperature: 10 to 15 minutes) for 5 cycles
While mated with corresponding or protective cap submerged at
depth of 1m for half hour.
Applicable cable diameter range
4.2 to 5
3.5 to 4.3
6.2 to 7
3
■Plugs
●Crimp Type
●Solder Type
Part Number
HR30-6P-3S
HR30-6P-6S
HR30-6P-6P
HR30-6PA-3S
HR30-6PA-6S
HR30-6PA-6P
HR30-7P-12S
HR30-8P-12P
CL No.
130-0004-1
130-0010-4
130-0009-5
130-0021-0
130-0019-9
130-0020-8
130-0027-7
130-0026-4
Weight A B Solder pot inner diameter
1.1 mm
0.8 mm
1.1 mm
0.8 mm
29.8
30.3
29.8
30.3
HR30-7P-12SC (Shown)
Shown with terminated and installed contacts.
Note: Crimp contacts are not included. Please order applicable contacts separately.
HR30-6P-6S (Shown)
4g
6.7g
Part Number
HR30-7P-10SC
HR30-7P-12SC
HR30-8P-12PC
CL No.
130-0013-2
130-0014-5
130-0015-8
Weight
Applicable cable diameter range
A Crimp contact
HR30-SC-211
HR30-PC-211
6.2 to 7 6g
12.6
39.8 15.5 0.6 mm
39.8
1
6
5
2
4
3
A(Fully tightened) Applicable
cable diameter
B
A(Fully tightened)
Applicable
cable diameter
Ø15.5
4
■Receptacles
●Solder Type
HR30-6R-6P (Shown)
16
18.4
Part Number
HR30-6R-3P
HR30-6R-6P
HR30-6R-6S
HR30-7R-12P
HR30-8R-12S
CL No. Weight
130-1003-4
130-1009-0
130-1008-8
130-1016-6
130-1018-1
3.4g
A
18.6
B
8.3
9.3
C
12 8.9
15 11.5
M8∞0.75
M11∞11013
D E F
Solder pot inner diameter
1.1mm
0.8mm
0.6mm
●Through hole Type
HR30-8R-12SD (Shown)
14.9
15.2
16
Part Number
HR30-6R-6PD
HR30-6R-6SD
HR30-7R-12PD
HR30-8R-12SD
CL No. Weight
130-1020-3
130-1021-6
130-1017-9
130-1019-4
2g
3.4g
A B
8.3
9.3
C
12
15
8.9
11.5
M8∞0.75
M11∞11013
D E F
●Crimp Type
Ø11.5
Ø15
15.5
9.3
Gasket
M11X1(Thread)
13(Hex nut)
Lock washer
HR30-7R-12PC (Shown)
Part Number
HR30-7R-10PC
HR30-7R-12PC
HR30-8R-12SC
CL No.
130-1012-5
130-1013-8
130-1014-0
Weight Crimp contact
HR30-PC-211
HR30-SC-211
3g
2g
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.
Shown with terminated and installed contacts.Shown with terminated and installed contacts.
A
B
1
6
2
5
4
3
C
D
Gasket
E(Thread)
F(Hex nut)
Lock washer
D
C
A
B
2
Through hole post
(0.2∞0.5)
E
F(Hex nut)
Lock washer
Gasket
Loading...