HP HP Pro 2110 Small Form Factor, Pro 3120 Minitower, Pro 3120 Small Form Factor, Pro 3125 Minitower, Pro 3130 Minitower Maintenance & Service Manual
...
Maintenance & Service Guide
HP Pro 2110 Small Form Factor
HP Pro 3120 Minitower
HP Pro 3120 Small Form Factor
HP Pro 3125 Minitower
HP Pro 3130 Minitower
HP Pro 3130 Small Form Factor
© Copyright 2010 Hewlett-Packard
Development Company, L.P. The information
contained herein is subject to change
without notice.
Microsoft and Windows are trademarks of
Microsoft Corporation in the U.S. and other
countries.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
photocopied, reproduced, or translated to
another language without the prior written
consent of Hewlett-Packard Company.
Maintenance & Service Guide
HP Pro 2110 Small Form Factor
HP Pro 3120 Minitower
HP Pro 3120 Small Form Factor
HP Pro 3125 Minitower
HP Pro 3130 Minitower
HP Pro 3130 Small Form Factor
First Edition (May 2010)
Document Part Number: 621937-001
About This Book
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage
to equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
iii
iv About This Book
Table of contents
1 Installing and Customizing the Software ........................................................................... 1
Installing the Operating System .................................................................................................. 1
Downloading Microsoft Windows Updates ................................................................................. 2
Installing or Upgrading Device Drivers (Windows systems) ............................................................ 2
Accessing Disk Image (ISO) Files ............................................................................................... 2
Protecting the Software ............................................................................................................. 3
2 Computer Setup (F10) Utility ............................................................................................. 4
HP Pro 2110 – Computer Setup (F10) Utilities ............................................................................. 4
Using Computer Setup (F10) Utilities ............................................................................ 5
Computer Setup—Main ............................................................................................. 6
Computer Setup—Advanced ...................................................................................... 7
Computer Setup—Boot .............................................................................................. 8
Computer Setup—Power ............................................................................................ 9
Computer Setup—PC Health ..................................................................................... 10
Computer Setup—Exit .............................................................................................. 10
HP Pro 3120 – Computer Setup (F10) Utilities ........................................................................... 11
Using Computer Setup (F10) Utilities .......................................................................... 11
Computer Setup—Main ........................................................................................... 12
Computer Setup—Advanced .................................................................................... 14
Computer Setup—Power .......................................................................................... 15
Computer Setup—Boot ............................................................................................ 16
Computer Setup—Exit .............................................................................................. 17
HP Pro 3125 – Computer Setup (F10) Utilities ........................................................................... 17
Using Computer Setup (F10) Utilities .......................................................................... 17
Computer Setup—Main ........................................................................................... 18
Computer Setup—Advanced .................................................................................... 20
Computer Setup—Power .......................................................................................... 21
Computer Setup—Boot ............................................................................................ 21
Computer Setup—Exit .............................................................................................. 22
HP Pro 3130 – Computer Setup (F10) Utilities ........................................................................... 23
Using Computer Setup (F10) Utilities .......................................................................... 23
Computer Setup—Main ........................................................................................... 24
Computer Setup—Advanced .................................................................................... 26
v
Computer Setup—Power .......................................................................................... 27
Computer Setup—Boot ............................................................................................ 28
Computer Setup—Exit .............................................................................................. 29
3 Serial ATA (SATA) Drive Guidelines and Features ............................................................. 30
SATA Hard Drives .................................................................................................................. 30
SATA Hard Drive Cables ........................................................................................................ 30
SATA Data Cable ................................................................................................... 30
SMART ATA Drives ................................................................................................................ 31
Hard Drive Capacities ............................................................................................................ 31
4 Identifying the Chassis, Routine Care, and Disassembly Preparation ............................... 32
Chassis Designation ............................................................................................................... 33
Minitower .............................................................................................................. 33
Small Form Factor ................................................................................................... 34
Electrostatic Discharge Information ........................................................................................... 35
Generating Static .................................................................................................... 35
Preventing Electrostatic Damage to Equipment ............................................................ 35
Personal Grounding Methods and Equipment ............................................................. 36
Grounding the Work Area ....................................................................................... 36
Recommended Materials and Equipment .................................................................... 37
Operating Guidelines ............................................................................................................. 37
Routine Care ......................................................................................................................... 38
General Cleaning Safety Precautions ......................................................................... 38
Cleaning the Computer Case .................................................................................... 38
Cleaning the Keyboard ............................................................................................ 38
Cleaning the Monitor ............................................................................................... 39
Cleaning the Mouse ................................................................................................ 39
Service Considerations ........................................................................................................... 39
Power Supply Fan ................................................................................................... 39
Tools and Software Requirements .............................................................................. 40
Screws ................................................................................................................... 40
Cables and Connectors ........................................................................................... 40
Hard Drives ............................................................................................................ 40
Lithium Coin Cell Battery .......................................................................................... 41
5 Removal and Replacement Procedures Minitower (MT) Chassis ....................................... 42
Preparation for Disassembly .................................................................................................... 42
Access Panel ......................................................................................................................... 43
Front Bezel ............................................................................................................................ 44
Bezel Blanks .......................................................................................................................... 45
Memory ................................................................................................................................ 45
DDR3-SDRAM DIMMs .............................................................................................. 45
vi
Populating DIMM Sockets ........................................................................................ 47
Installing Memory Modules ....................................................................................... 52
Expansion Cards .................................................................................................................... 54
Cable Management ............................................................................................................... 60
Cable Connections .................................................................................................. 61
HP Pro 3120 ........................................................................................... 61
HP Pro 3125 ........................................................................................... 61
HP Pro 3130 ........................................................................................... 62
Drives ................................................................................................................................... 63
Drive Positions ........................................................................................................ 63
Installing Additional Drives ....................................................................................... 64
System Board Drive Connections ................................................................ 65
Removing an Optical Drive ........................................................................ 68
Removing an Internal 3.5-inch Hard Drive ................................................... 69
Front I/O and USB Panel Housing Assembly ............................................................................. 72
Power Switch/LED Assembly ................................................................................................... 73
System Fan ............................................................................................................................ 74
Heat sink assembly ................................................................................................................. 75
Processor .............................................................................................................................. 76
Power Supply ........................................................................................................................ 79
System Board ........................................................................................................................ 82
Battery .................................................................................................................................. 84
Type 1 Battery Holder .............................................................................................. 85
Type 2 Battery Holder .............................................................................................. 85
Type 3 Battery Holder .............................................................................................. 86
6 Removal and Replacement Procedures Small Form Factor (SFF) Chassis ........................... 87
Preparation for Disassembly .................................................................................................... 87
Access Panel ......................................................................................................................... 88
Front Bezel ............................................................................................................................ 89
Installing Additional Memory ................................................................................................... 90
DIMMs .................................................................................................................. 90
DDR3-SDRAM DIMMs .............................................................................................. 90
Populating DIMM Sockets ........................................................................................ 91
Installing DIMMs ..................................................................................................... 95
Expansion Cards .................................................................................................................... 97
System Fan .......................................................................................................................... 103
Cable Management ............................................................................................................. 104
Cable Connections ................................................................................................ 105
HP Pro 2110 ......................................................................................... 105
HP Pro 3120 ......................................................................................... 105
HP Pro 3130 ......................................................................................... 106
Optical Drive Eject Button ..................................................................................................... 107
vii
Drives ................................................................................................................................. 109
Drive Positions ...................................................................................................... 109
Installing and Removing Drives ............................................................................... 110
System Board Drive Connections .............................................................. 111
Removing the Optical Drive ..................................................................... 113
Removing the Hard Drive ........................................................................ 114
Front I/O Assembly .............................................................................................................. 117
Power Switch/LED Assembly ................................................................................................. 119
Heat sink ............................................................................................................................ 122
Processor ............................................................................................................................ 123
Power Supply ...................................................................................................................... 126
System Board ...................................................................................................................... 128
Battery ................................................................................................................................ 130
Type 1 Battery Holder ............................................................................................ 131
Type 2 Battery Holder ............................................................................................ 131
7 Restore and Recovery ................................................................................................... 133
Microsoft System Restore ....................................................................................................... 133
System Recovery .................................................................................................................. 133
System Recovery Options ....................................................................................... 134
System Recovery from the Windows Start Menu ........................................................ 134
System Recovery at System Startup .......................................................................... 135
System Recovery from Recovery Discs ...................................................................... 135
Recovery Discs ..................................................................................................................... 136
Choosing Recovery Discs ....................................................................................... 136
Creating Recovery Discs ........................................................................................ 137
8 Computer Diagnostic Features ....................................................................................... 138
Hewlett-Packard Vision Diagnostics ........................................................................................ 138
Accessing HP Vision Diagnostics ............................................................................. 138
Survey Tab ........................................................................................................... 139
Test Tab ............................................................................................................... 140
Status Tab ............................................................................................................ 140
History Tab .......................................................................................................... 141
Errors Tab ............................................................................................................ 141
Help Tab .............................................................................................................. 142
Saving and Printing Information in HP Vision Diagnostics ........................................... 142
Downloading the Latest Version of HP Vision Diagnostics ........................................... 142
Protecting the Software ......................................................................................................... 143
9 Troubleshooting Without Diagnostics ............................................................................ 144
Safety and Comfort .............................................................................................................. 144
Before You Call for Technical Support .................................................................................... 144
viii
Helpful Hints ........................................................................................................................ 145
Solving General Problems ..................................................................................................... 147
Solving Diskette Problems ...................................................................................................... 151
Solving Hard Drive Problems ................................................................................................. 153
Solving Media Card Reader Problems .................................................................................... 154
Solving Display Problems ...................................................................................................... 156
Solving Audio Problems ........................................................................................................ 159
Solving Printer Problems ........................................................................................................ 161
Solving Keyboard and Mouse Problems .................................................................................. 162
Solving Hardware Installation Problems .................................................................................. 165
Solving Network Problems .................................................................................................... 167
Solving Memory Problems ..................................................................................................... 170
Solving CD-ROM and DVD Problems ...................................................................................... 171
Solving USB Flash Drive Problems .......................................................................................... 174
Solving Front Panel Component Problems ................................................................................ 175
Solving Internet Access Problems ............................................................................................ 176
Solving Software Problems .................................................................................................... 179
Contacting Customer Support ................................................................................................ 180
10 POST Error Messages .................................................................................................. 181
POST Text Messages ............................................................................................................ 181
Interpreting POST Diagnostic Audible Codes ........................................................................... 182
11 Password Security and Resetting CMOS ...................................................................... 184
Resetting the Password Jumper ............................................................................................... 184
Clearing and Resetting the CMOS ......................................................................................... 185
Appendix A Connector Pin Assignments ........................................................................... 187
Ethernet BNC ...................................................................................................................... 187
USB .................................................................................................................................... 187
Microphone ........................................................................................................................ 187
Headphone ......................................................................................................................... 188
Line-in Audio ....................................................................................................................... 188
Line-out Audio ...................................................................................................................... 188
4-Pin Power (for CPU) ........................................................................................................... 188
Monitor .............................................................................................................................. 189
24-Pin Power ....................................................................................................................... 189
PCI Express ......................................................................................................................... 190
PCI Express ......................................................................................................................... 191
Appendix B Power Cord Set Requirements ....................................................................... 192
General Requirements .......................................................................................................... 192
Japanese Power Cord Requirements ....................................................................................... 192
ix
Country-Specific Requirements ............................................................................................... 193
Appendix C Specifications ................................................................................................ 194
Minitower models ................................................................................................................ 194
Small form factor models ....................................................................................................... 195
Index ............................................................................................................................... 196
x
1 Installing and Customizing the
Software
If your computer was not shipped with a Microsoft operating system, some portions of this
documentation do not apply. Additional information is available in online help after you install the
operating system.
NOTE: If the computer was shipped with Windows Vista or Windows 7 loaded, you will be
prompted to register the computer with HP Total Care before installing the operating system. You will
see a brief movie followed by an online registration form. Fill out the form, click the Begin button, and
follow the instructions on the screen.
CAUTION: Do not add optional hardware or third-party devices to the computer until the operating
system is successfully installed. Doing so may cause errors and prevent the operating system from
installing properly.
NOTE: Be sure there is a 10.2-cm (4-inch) clearance at the back of the unit and above the monitor to
permit the required airflow.
Installing the Operating System
The first time you turn on the computer, the operating system is installed automatically. This process
takes about 5 to 10 minutes, depending on which operating system is being installed. Carefully read
and follow the instructions on the screen to complete the installation.
CAUTION: Once the automatic installation has begun, DO NOT TURN OFF THE COMPUTER UNTIL
THE PROCESS IS COMPLETE. Turning off the computer during the installation process may damage the
software that runs the computer or prevent its proper installation.
NOTE: If the computer shipped with more than one operating system language on the hard drive, the
installation process could take up to 60 minutes.
If your computer was not shipped with a Microsoft operating system, some portions of this
documentation do not apply. Additional information is available in online help after you install the
operating system.
Installing the Operating System
1
Downloading Microsoft Windows Updates
1. To set up your Internet connection, click Start > Internet Explorer and follow the instructions
on the screen.
2. Once an Internet connection has been established, click the Start button.
3. Select the All Programs menu.
4. Click on the Windows Update link.
In Windows Vista and Windows 7, the Windows Update screen appears. Click view
available updates and make sure all critical updates are selected. Click the Install button and
follow the instructions on the screen.
In Windows XP, you will be directed to the Microsoft Windows Update Web site. If you see
one or more pop-up windows that ask you to install a program from
http://www.microsoft.com,
click Yes to install the program. Follow the instructions on the Microsoft Web site to scan for
updates and install critical updates and service packs.
It is recommended that you install all of the critical updates and service packs.
5.
After the updates have been installed, Windows will prompt you to reboot the machine. Be sure to
save any files or documents that you may have open before rebooting. Then select Yes to reboot
the machine.
Installing or Upgrading Device Drivers (Windows
systems)
When installing optional hardware devices after the operating system installation is complete, you must
also install the drivers for each of the devices.
If prompted for the i386 directory, replace the path specification with C:\i386, or use the Browse
button in the dialog box to locate the i386 folder. This action points the operating system to the
appropriate drivers.
Obtain the latest support software, including support software for the operating system from
http://www.hp.com/support. Select your country and language, select Download drivers and
software (and firmware), enter the model number of the computer, and press Enter.
Accessing Disk Image (ISO) Files
There are disk image files (ISO files) included on your PC that contain the installation software for
additional software. These CD image files are located in the folder C:\SWSetup\ISOs. Each .iso file
can be burned to CD media to create an installation CD. It is recommended that these disks be created
and the software installed in order to get the most from your PC. The software and image file names
are:
●
Corel WinDVD SD and BD – installation software for WinDVD – used to play DVD movies
●
HP Insight Diagnostics OR Vision Diagnostics – software to perform diagnostic activities on your
PC
2 Chapter 1 Installing and Customizing the Software
Protecting the Software
To protect the software from loss or damage, keep a backup copy of all system software, applications,
and related files stored on the hard drive. Refer to the operating system or backup utility documentation
for instructions on making backup copies of your data files.
Protecting the Software
3
2 Computer Setup (F10) Utility
The computer setup utility differs for the different models.
HP Pro 2110 – Computer Setup (F10) Utilities
Use Computer Setup (F10) Utility to do the following:
●
Change factory default settings.
●
Set the system date and time.
●
Set, view, change, or verify the system configuration, including settings for processor, graphics,
memory, audio, storage, communications, and input devices.
●
Modify the boot order of bootable devices such as hard drives, diskette drives, optical drives, or
USB flash media devices.
●
Restrict a device from booting the unit.
●
Run hard drive self-tests.
●
View CPU and system temperatures.
●
Establish a supervisor password that controls access to Computer Setup (F10) Utility and the
settings described in this section.
●
Secure integrated I/O functionality, including the serial, USB, or parallel ports, audio, or
embedded NIC, so that they cannot be used until they are unsecured.
●
Enable or disable pre-boot messages.
●
Enable or disable USB legacy support.
4 Chapter 2 Computer Setup (F10) Utility
Using Computer Setup (F10) Utilities
Computer Setup can be accessed only by turning the computer on or restarting the system. To access
the Computer Setup Utilities menu, complete the following steps:
1.
Turn on or restart the computer.
2.
As soon as the computer is turned on, press F10 before the system boots to the operating system
to enter Computer Setup. Press Enter to bypass the title screen, if necessary.
NOTE: If you do not press F10 at the appropriate time, you must restart the computer and again
press F10 before the unit boots to the operating system to access the utility.
3.
The Computer Setup Utility screen is divided into menu headings and actions.
Six menu headings appear on the Computer Setup Utility screen:
●
Main
●
Advanced
●
Boot
●
Power
●
PC Health
●
Exit
Use the arrow keys to select the appropriate heading, then press Enter. Use the arrow (up and
down) keys to select the option you want, then press Enter. To return to the previous screen, press
Esc.
4.
To apply and save changes, press the F10 key.
If you have made changes that you do not want applied, press the F5 key to return to the previous
values.
To load optimized default values, press the F7 key.
CAUTION: Do NOT turn the computer power OFF while the ROM is saving the Computer Setup
(F10) changes because the CMOS could become corrupted. It is safe to turn off the computer only after
exiting the F10 Setup screen.
Table 2-1 Computer Setup (F10) Utility Main Menu
Heading Table
Main
Computer Setup—Main on page 6
Advanced
Computer Setup—Advanced on page 7
Boot
Computer Setup—Boot on page 8
Power
Computer Setup—Power on page 9
PC Health
Computer Setup—PC Health on page 10
Exit
Computer Setup—Exit on page 10
HP Pro 2110 – Computer Setup (F10) Utilities
5
Computer Setup—Main
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-2 Computer Setup—Main
Option Description
System Information
Allows you to view the following system information:
●
Processor Type (view only)
●
Processor Speed (view only)
●
CPUID/PatchID (view only)
●
Cache Size (view only)
●
Memory Size (view only)
●
Integrated MAC (view only)
●
System BIOS (view only)
System IDs
Allows you to view or change the following system identification information:
●
Product Name (press Enter to change)
●
Serial Number (press Enter to change)
●
UUID (press Enter to change)
●
SKU Number (press Enter to change)
●
Family Name (view only)
●
Asset Tag Number (press Enter to change)
●
Feature Byte (press Enter to change)
●
Build ID (press Enter to change)
Set Time and Date
Allows you to set system time and date.
SATA Port 1
SATA Port 2
SATA Port 3
SATA Port 4
Allows or displays the following for each SATA Port:
●
Port Configuration — Disable/enable SATA Port
●
HDD Self-Test for selected channel:
◦
SMART Status Check
◦
HDD Short Self-Test
◦
HDD Extended Self-Test
●
Vendor (view only)
●
Size (view only)
●
Firmware (view only)
6 Chapter 2 Computer Setup (F10) Utility
Table 2-2 Computer Setup—Main (continued)
Option Description
SATA Controller
Allows you to choose how the SATA controller and devices are accessed by the operating system.
The following options are available:
●
Native Mode - 4 SATA port
●
Compatible Mode - 2 PATA devices and 2 SATA devices (ports)
Onboard FDC
Controller
Disables/enables the floppy disk controller.
Drive A
(view only)
Halt On
Allows you to set POST error behavior to:
●
No Errors
●
All Errors
●
All But Keyboard
POST Delay
Allows you to set a POST delay to:
●
0 seconds
●
5 seconds
●
10 seconds
●
15 seconds
●
30 seconds
Computer Setup—Advanced
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-3 Computer Setup—Advanced
Option Description
Execute Disable Bit
Disables/enables hardware DEP function.
Intel (R)
Virtualization Tech
Allows you to enable/disable the processor's Virtualization Technology feature.
Init Display First
Allows you to select the primary display device:
●
OnChip VGA
●
PCI Slot
●
PCIEx
HP Pro 2110 – Computer Setup (F10) Utilities
7
Table 2-3 Computer Setup—Advanced (continued)
Option Description
MAX DVMT
Allocation
Allows you to specify the DVMT/system memory allocated for video memory:
●
128MB
●
256MB
●
Max
Onboard HD Audio
Allows you to disable/enable onboard HD audio.
OnChip USB
Controller
Disables/enables the universal host controller interface for USB (Universal Serial Bus).
USB Legacy Support
Disables/enables USB legacy support function (USB keyboard, USB mouse, and USB flash media).
Onboard LAN
Disables/enables onboard LAN controller.
Onboard LAN Boot
ROM
Disables/enables the boot ROM of the onboard LAN chip.
Onboard Serial Port
1
Allows you to select a setting for the onboard serial port:
●
Disabled
●
3F8/IRQ4
●
2F8/IRQ3
●
3E8/IRQ4
●
2E8/IRQ3
Computer Setup—Boot
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-4 Computer Setup—Boot
Option Description
ESC Boot Menu
Allows you to enable/disable the option to press the ESC key to access the Boot menu during
computer startup.
F9 Diagnostics
Disables/enables F9 Boot Menu prompt message on the logo screen.
F10 Setup Prompt
Disables/enables the F10 Setup prompt message on the logo screen.
F11 Recovery
Disables/enables F11 Recovery and provides the option of showing the F11 Recovery prompt
message on the logo screen. Choose from the following:
●
Disabled
●
Enabled no prompt
●
Enabled and prompt
8 Chapter 2 Computer Setup (F10) Utility
Table 2-4 Computer Setup—Boot (continued)
Option Description
F12 Boot from LAN
Prompt
Disables/enables the F12 Boot from LAN prompt message on the logo screen.
Hard Disk Boot Seq.
Allows you to specify the order of attached hard drive devices (such as USB HDD storage or USB
flash media). The first drive in the order has priority in the boot sequence and is recognized as
drive C (if any devices are attached).
Optical Drive Boot
Seq.
Allows you to specify the order in which attached optical drives (including USB ODD) are checked
for a bootable operating system image.
Network Boot Seq.
Allows you to specify the order in which network devices (including UP NIC cards) are checked for
a bootable operating system image.
First Boot Device
Second Boot Device
Third Boot Device
Fourth Boot Device
Allows you to specify which devices will boot first, second, third, and fourth or to disable any of the
four:
●
Removable
●
CDROM
●
Hard Disk
●
Network
NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS operating system
has started.
Set Supervisor
Password
Allows you to establish a password to control access to Computer Setup.
BIOS Write
Protection
Disables/enables BIOS upgrading.
Computer Setup—Power
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-5 Computer Setup—Power
Option Description
After AC Power Loss
Allows you to select system power loss behavior:
●
Off
●
On
●
Last State
Wake on PCI Device
from S5
Disables/enables waking up from S5 by PCI device.
RTC Alarm Resume
Disables/enables RTC (real-time clock) alarm.
HP Pro 2110 – Computer Setup (F10) Utilities
9
Computer Setup—PC Health
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-6 Computer Setup—PC Health
Option Description
Chassis Opened
Warning
Allows you to disable/enable the chassis intrusion function and clear the intrusion warning.
System Fan Fail
Check
Disables/enables detection of system fan during POST.
Smart Fan Function
Disables/enables Smart Fan functionality. Enabling optimizes fan control for best acoustic behavior.
Current CPU
Temperature
(view only)
Current System
Temperature
(view only)
Current CPU Fan
Speed
(view only)
Current System Fan
Speed
(view only)
Computer Setup—Exit
Table 2-7 Computer Setup—Exit
Option Description
Save & Exit Setup
Allows you to save current settings and exit Computer Setup.
Exit Without Saving
Allows you to exit Computer Setup without saving changes.
Load Optimal
Defaults
Allows you to reset Computer Setup to factory defaults.
10 Chapter 2 Computer Setup (F10) Utility
HP Pro 3120 – Computer Setup (F10) Utilities
Use Computer Setup (F10) Utility to do the following:
●
Change factory default settings.
●
Set the system date and time.
●
Set, view, change, or verify the system configuration, including settings for graphics, audio,
storage, communications, and input devices.
●
View settings for processor and memory.
●
Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media
devices.
●
Run hard drive self-tests.
●
Establish a supervisor password that controls access to Computer Setup (F10) Utility and the
settings described in this section.
Using Computer Setup (F10) Utilities
Computer Setup can be accessed only by turning the computer on or restarting the system. To access
the Computer Setup Utilities menu, complete the following steps:
1.
Turn on or restart the computer.
2.
As soon as the computer is turned on, press F10 before the computer boots to the operating
system to enter Computer Setup.
NOTE: If you do not press F10 at the appropriate time, you must restart the computer and again
press F10 before the computer boots to the operating system to access the utility.
3.
The Computer Setup Utility screen is divided into menu headings and actions.
Five menu headings appear on the Computer Setup Utility screen:
●
Main
●
Advanced
●
Power
●
Boot
●
Exit
Use the arrow keys to select the appropriate heading, then press Enter. Use the arrow (up and
down) keys to select the option you want, then press Enter. To return to the previous screen, press
Esc.
CAUTION: Do NOT turn the computer power OFF while the ROM is saving the Computer Setup
(F10) changes because the CMOS could become corrupted. It is safe to turn off the computer only after
exiting the F10 Setup screen.
HP Pro 3120 – Computer Setup (F10) Utilities
11
Computer Setup—Main
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-8 Computer Setup—Main
Option Description
System Time
Allows you to set system time.
System Date
Allows you to set system date.
System IDs
Allows you to view the following system identification information:
●
Product Name (view only)
●
Serial Number (view only)
●
UUID (view only)
●
SKU Number (view only)
●
Family Name (view only)
●
Feature Byte (view only)
●
Build ID (view only)
Language
Allows you to select language.
Floppy Diskette A
Allows you to set drive A to:
●
Disabled
●
1.44 MB 3.5”
●
Not Installed (default)
12 Chapter 2 Computer Setup (F10) Utility
Table 2-8 Computer Setup—Main (continued)
1st Drive
2nd Drive
3rd Drive
4th Drive
For each, allows you to adjust or view:
●
Capacity (Size - HDD only) - view only
●
Transfer Mode- view only
●
Smart Support - run HDD self-test for selected channel:
◦
SMART Status Check
◦
SMART Short Self-Test
◦
SMART Extended Self-Test
System Information
Allows you to view:
●
Installed Memory
●
Memory Bank 1
●
Memory Bank 2
●
Memory Bank 3
●
Memory Bank 4
●
BIOS Revision
●
Core Version
HP Pro 3120 – Computer Setup (F10) Utilities
13
Computer Setup—Advanced
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
WARNING! Setting items on this menu to incorrect values may cause your system to malfunction.
Table 2-9 Computer Setup—Advanced
Option Description
CPU Type
(view only)
CPU Speed
(view only)
Cache RAM
(view only)
Cache RAM (L2)
(view only)
Cache RAM (L3)
(view only)
Primary Video
Adapter
Allows you to select the boot display device when more than 2 video options are offered by the
system:
●
PCI-E (default)
●
Onboard
USB Ports
Allows you to disable/enable individual USB ports.
SATA Controller
Allows you to disable/enable the SATA controller. Default is enabled.
SATA Controller
Mode
If SATA Controller is enabled, allows you to set the mode to:
●
IDE (default)
●
AHCI
●
RAID
Onboard Audio
Allows you to set the onboard audio to:
●
Enabled
●
Disabled
●
Auto (default)
Onboard LAN
Allows you to disable/enable onboard LAN controller. Default is enabled.
Onboard LAN Boot
ROM
Disables/enables the boot ROM of the onboard LAN chip. Default is enabled.
Change Supervisor
Password
Allows you to establish, disable, or change the supervisor password.
Change User
Password
Allows you to establish, disable, or change the user password.
NOTE: Only displays if a Supervisor password is set.
Supervisor
Password
Allows you to view whether the supervisor password is enabled or disabled.
User Password
Allows you to view whether the user password is enabled or disabled.
14 Chapter 2 Computer Setup (F10) Utility
Computer Setup—Power
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-10 Computer Setup—Power
Option Description
After AC Power
Failure
Allows you to select system restart behavior after power loss:
●
Auto
●
Power On
●
Stay Off (default)
XD (Execute Disable)
(if supported by
hardware)
Allows you to disable/enable the processor's XD feature. Default is enabled.
Virtualization
Technology
Allows you to enable/disable the processor's Virtualization Technology feature. Default is disabled.
WOL in S5
Disables/enables limited Wake on LAN from S5. Note that the computer can only wake from S5
during a normal shutdown event. Default is disabled.
HP Pro 3120 – Computer Setup (F10) Utilities
15
Computer Setup—Boot
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-11 Computer Setup—Boot
Option Description
Boot-time
Diagnostic
Screen
Disables/enables POST diagnostic messages display during boot. Default is disabled.
Boot Device
Priority
Allows you to specify which device groups will boot first, second, third, and fourth or to disable any of
the four. Also allows you to set the device boot priority within each group.
1st Boot Device
2nd Boot Device
3rd Boot Device
4th Boot Device
Allows you to set the device group boot priority:
●
CD-ROM Group
●
Hard Drive Group
●
Floppy Group
●
Network Boot Group
NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS
operating system has started.
Floppy Group
Boot Priority
Specifies boot device priority within removable devices.
NOTE: This computer does not support floppy drives.
CD-ROM Group
Boot Priority
Specifies boot device priority within CD/DVD drives.
HDD Group Boot
Priority
Specifies boot device priority within hard drives.
Network Group
Boot Priority
Specifies boot device priority within bootable network devices.
16 Chapter 2 Computer Setup (F10) Utility
Computer Setup—Exit
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-12 Computer Setup—Exit
Option Description
Exit Saving Changes
Press Enter to exit saving changes.
Exit Discarding
Changes
Press Enter to exit discarding changes.
Load Setup Defaults
Press Enter to load setup defaults.
Discard Changes
Press Enter to discard changes.
Save Changes
Press Enter to save changes.
HP Pro 3125 – Computer Setup (F10) Utilities
Use Computer Setup (F10) Utility to do the following:
●
Change factory default settings.
●
Set the system date and time.
●
Set, view, change, or verify the system configuration, including settings for graphics, audio,
storage, communications, and input devices.
●
View settings for processor and memory.
●
Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media
devices.
●
Run hard drive self-tests.
●
Establish a supervisor password that controls access to Computer Setup (F10) Utility and the
settings described in this section.
Using Computer Setup (F10) Utilities
Computer Setup can be accessed only by turning the computer on or restarting the system. To access
the Computer Setup Utilities menu, complete the following steps:
1.
Turn on or restart the computer.
2.
As soon as the computer is turned on, press F10 before the computer boots to the operating
system to enter Computer Setup.
NOTE: If you do not press F10 at the appropriate time, you must restart the computer and again
press F10 before the computer boots to the operating system to access the utility.
3.
The Computer Setup Utility screen is divided into menu headings and actions.
HP Pro 3125 – Computer Setup (F10) Utilities
17
Five menu headings appear on the Computer Setup Utility screen:
●
Main
●
Advanced
●
Power
●
Boot
●
Exit
Use the arrow keys to select the appropriate heading, then press Enter. Use the arrow (up and
down) keys to select the option you want, then press Enter. To return to the previous screen, press
Esc.
CAUTION: Do NOT turn the computer power OFF while the ROM is saving the Computer Setup
(F10) changes because the CMOS could become corrupted. It is safe to turn off the computer only after
exiting the F10 Setup screen.
Computer Setup—Main
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 2-13 Computer Setup—Main
Option Description
System Time
Allows you to set system time.
System Date
Allows you to set system date.
System IDs
Allows you to view or change the following system identification information:
●
Product Name (press Enter to change)
●
Serial Number (press Enter to change)
●
UUID (press Enter to change)
● SKU Number (press Enter to change)
●
Family Name (view only)
●
Feature Byte (press Enter to change)
●
Build ID (press Enter to change)
Language
Allows you to select language.
Floppy Diskette A
Allows you to set drive A to:
●
Disabled
●
1.44 MB 3.5”
●
Not Installed
18 Chapter 2 Computer Setup (F10) Utility
Table 2-13 Computer Setup—Main (continued)
1st Drive
2nd Drive
3rd Drive
4th Drive
For each, allows you to adjust or view:
●
Port Configuration - disable/enable the SATA port for the selected drive
●
Capacity (Size - HDD only) - view only
●
Transfer Mode- view only
●
Smart Support - run HDD self-test for selected channel:
◦
SMART Status Check
◦
SMART Short Self-Test
◦
SMART Extended Self-Test
System Information
Allows you to view:
●
Installed Memory
● Memory Bank 1
●
Memory Bank 2
●
Memory Bank 3
●
Memory Bank 4
●
BIOS Revision
●
Core Version
HP Pro 3125 – Computer Setup (F10) Utilities
19
Computer Setup—Advanced
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
WARNING! Setting items on this menu to incorrect values may cause your system to malfunction.
Table 2-14 Computer Setup—Advanced
Option Description
CPU Type
(view only)
CPU Speed
(view only)
Cache RAM (L2)
(view only)
Cache RAM (L3)
(view only)
Primary Video
Adapter
Allows you to select the boot display device when more than 2 video options are offered by the
system:
●
Onboard
●
PCI-E
SATA1 Controller
Allows you to disable/enable the SATA controller.
SATA1 Controller
Mode
If SATA Controller is enabled, allows you to set the mode to:
●
IDE
●
AHCI
USB Ports
Allows you to disable/enable individual USB ports.
Onboard LAN
Allows you to disable/enable onboard LAN controller.
Onboard LAN Boot
ROM
Disables/enables the boot ROM of the onboard LAN chip.
Supervisor
Password
Allows you to view whether the supervisor password is enabled or disabled.
User Password
Allows you to view whether the user password is enabled or disabled.
NOTE: Only displays if a Supervisor password is set.
Change Supervisor
Password
Allows you to establish, disable, or change the supervisor password.
Change User
Password
Allows you to establish, disable, or change the user password.
NOTE: Only displays if a Supervisor password is set.
Onboard Audio
Allows you to set the onboard audio to:
●
Disabled
●
Enabled
●
Auto
20 Chapter 2 Computer Setup (F10) Utility
Loading...