HP (Hewlett-Packard) PCLA8205B User Manual
EtherExpress
PCLA8205B
TM
PRO/10+ ISA
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
TM
MMX
Pentium® is a registered trademark of Intel Corporation.
is a trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
1 Connecting to a Netware 3.12 Server
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
Windows for
Workgroups
Version 3.11
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Intel EtherExpress ISA 10MBS Ethernet adapter card and drivers disk
Ver. 2.3.
• D r i v e r N a m e : E P R O . 3 8 6 S i z e : 1 6 K B D a t e : 1 0 / 2 2 / 9 6
• Novell Netware 3.12 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
• Netware Client for DOS and MS Windows
Device Configuration
• I/O Addres 350 - 35Fh
• Interrupt IRQ 10
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO ISA
Ethernet adapter card into an ISA slot.
2 Connect network cable media to the Intel EtherExpress card.
3 Power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk Ver. 2.3.”, and
execute “A:\SOFTSET2.EXE.”
5 Select “Change Adapter configuration” and verify the resource settings
listed above under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
1 Connecting to a Netware 3.12 Server
Windows for Workgroups Version 3.11
7 Remove the Intel drivers diskette and reboot the machine, and boot to a
DOS prompt.
8 Insert Netware Client for DOS and Windows Disk 1 and execute
“A:\INSTALL.”
9 Change the settings to match the following and then option 6 to continue
the installation.
• C:\NWCLIENT
•YES
•YES
• C:\WINDOWS
•No
• Intel EtherExpress ™ Pro/10 LAN Adapter (Use the driver from the drivers disk at A:\)
10 Insert the corresponding diskettes to finish the file transfer, and then
reboot the machine.
11 After windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
12 Select the “Networks” button in the “Network Setup” and verify that
“Novell NetWare (Workstation Shell 4.0 and above)” is listed under
“Install Windows Support for the following network only:”
13 Click on “OK” twice to complete the installation.
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2.
• Intel EtherExpress PRO ISA ethernet card and drivers disk Ver. 2.3.
• Driver Name: El90X.DOS Size: 45KB Date: 3/21/97
• Novell Netware 3.12 server that supports Net BEUI,TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
• I/O Address 350 - 35Fh
• Interrupt IRQ 10
• Board Connector type Auto-detect
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO ISA
adapter card into an ISA slot.
2 Connect network Cable media to the Intel EtherExpress PRO ISA card.
3 Insert a DOS bootable diskette and power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk 1, “EtherExpress
drivers Ver. 2.3.” and execute “A:\SOFTSET2.EXE.”
5 Select “Configure NIC”, and verify the resource settings listed above
under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel EtherExpress software driver diskette and reboot the
machine.
8 Power on the machine and allow it to boot to Windows 95.
9 When Windows 95 restarts, a message will appear that new hardware has
been found.
1 Connecting to a Netware 3.12 Server
Windows 95 SR2
10 Click “OK” to the “Network” dialog box to provide computer / work group
names.
11 Specify your Computer Name, Workgroup, and Computer Description.
(If you do not have the required information, contact your network
administrator)
12 Click on “Close” button, and files will copy.
13 Click on the “Yes” button to finish the installation and restart your
computer.
2 Connecting to a Netware 4.11 Server
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
Windows for
Workgroups
Version 3.11
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Intel EtherExpress ISA 10MBS Ethernet adapter card and drivers disk
Ver. 2.3.
• D r i v e r N a m e : E P R O . 3 8 6 S i z e : 1 6 K B D a t e : 1 0 / 2 2 / 9 6
• Novell Netware 4.11 server that supports Net BEUI, NWLink IPX/SPX,
and NWLink NetBIOS transfer protocols.
• Netware Client for DOS and MS Windows
Device Configuration
• I/O Address 350 - 35Fh
• Interrupt IRQ 10
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO ISA
Ethernet adapter card into an ISA slot.
2 Connect network cable media to the Intel EtherExpress card.
3 Power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk Ver. 2.3.”, and
execute “A:\SOFTSET2.EXE.”
5 Select “Change Adapter configuration” and verify the resource settings
listed above under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
2 Connecting to a Netware 4.11 Server
Windows for Workgroups Version 3.11
7 Remove the Intel drivers diskette and reboot the machine, and boot to a
DOS prompt.
8 Insert Netware Client for DOS and Windows Disk 1 and execute
“A:\INSTALL.”
9 Change the settings to match the following and then option 6 to continue
the installation.
• C:\NWCLIENT
•YES
•YES
• C:\WINDOWS
•No
• Intel EtherExpress ™ Pro/10 LAN Adapter (Use the driver from the
drivers disk at A:\)
10 Insert the corre=10ponding diskettes to finish the file transfer, and then
reboot the machine.
11 After windows loads, open the “NETWORK” folder, and double-click the
“NETWORK SETUP” icon.
12 Select the “Networks” button in the “Network Setup” and verify that
“Novell NetWare (Workstation Shell 4.0 and above)” is listed under
“Install Windows Support for the following network only:”
13 Click on “OK” twice to complete the installation.
Windows 95 SR2 Requirements
• HP Vectra with Windows 95 SR2.
• Intel EtherExpress PRO ISA ethernet card and drivers disk Ver. 2.3.
• Driver Name: El90X.DOS Size: 45KB Date: 3/21/97
• Novell Netware 4.11 server that supports Net BEUI,TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
• I/O Address 350 - 35Fh
• Interrupt IRQ 10
• Board Connector type Auto-detect
2 Connecting to a Netware 4.11 Server
Windows 95 SR2
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO ISA
adapter card into an ISA slot.
2 Connect network Cable media to the Intel EtherExpress PRO ISA card.
3 Insert a DOS bootable diskette and power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk 1, “EtherExpress
drivers Ver. 2.3.” and execute “A:\SOFTSET2.EXE.”
5 Select “Configure NIC”, and verify the resource settings listed above
under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel EtherExpress software driver diskette and reboot the
machine.
8 Power on the machine and allow it to boot to Windows 95.
9 When Windows 95 restarts, a message will appear that new hardware has
been found.
2 Connecting to a Netware 4.11 Server
Windows 95 SR2
10 Click “OK” to the “Network” dialog box to provide computer / work group
names.
11 Specify your Computer Name, Workgroup, and Computer Description.
(If you do not have the required information, contact your network
administrator)
12 Click on “Close” button, and files will copy.
13 Click on the “Yes” button to finish the installation and restart your
computer.
3 Connecting to a Windows NT Server 3.51
Windows for Workgroups Version 3.11
3 Connecting to a Windows NT Server 3.51
Windows for
Workgroups
Version 3.11
Requirements
• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.
• Intel EtherExpress ISA 10MBS Ethernet adapter card and drivers disk
Ver. 2.3.
• D r i v e r N a m e : E l n k 3 . S Y S S i z e : 2 7 K B D a t e : 7 / 1 8 / 9 6
• Microsoft Windows NT server 3.51 machine that supports Net BEUI,
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
• I/O Address 350 - 35Fh
• Interrupt IRQ 10
• Board Connector type Auto-detect
• Force 8-bit operation Yes
• Flash chip address Disabled
• Remote boot program None
Procedure
1 With the HP Vectra turned off, install the Intel EtherExpress PRO ISA
Ethernet adapter card into an ISA slot.
2 Connect network Cable Media to the Intel EtherExpress card.
3 Power on the machine.
4 After booting, insert the Intel EtherExpress drivers disk Ver. 2.3.”, and
execute “A:\SOFTSET2.EXE.”
5 Select “Change Adapter configuration” and verify the resource settings
listed above under the heading “Device Configuration.”
6 If changes are required, save those changes and exit.
7 Remove the Intel Drivers diskette and reboot the machine.
Loading...