Instalación del set de teclado y ratón inalámbricos
Installation de la souris et du clavier sans fil
Installing the Wireless
Keyboard and Mouse Set
The wireless keyboard and mouse set consists
of a receiver (D) that plugs into the computer,
a wireless keyboard (K), and a wireless
mouse (M).
D
English
K
Note:
Installing the Wireless Keyboard and Mouse Set
This wireless set is compatible with
your model PC and not intended
for use with other computers.
Note:
You can replace the batteries in the
mouse and keyboard without turning off
the computer. The computer must be on to
change the ID setting on the three units.
M
1
Getting the Mouse Ready
M3
M2
Note:
M1
Do not use rechargeable batteries in
the mouse. Alkaline batteries are
recommended.
Install the two AA alkaline batteries (provided)
in the wireless mouse:
1 Push in at M1 and lift the battery cover (M2)
from the bottom of the mouse.
2 Insert the batteries into the compartment.
Note the battery images on the inside of the
compartment, and make sure batteries are
placed in the correct direction.
3 Replace the cover.
Note:
The red light (M3) turns on when the
batteries are installed correctly.
Installing the Wireless Keyboard and Mouse Set
2
Getting the Keyboard Ready
K
Note:
K3K2
Do not use rechargeable batteries in
the keyboard. Alkaline batteries are
recommended.
K1
K3
Install the two AA alkaline batteries (provided)
in the wireless keyboard:
1 Place the keyboard (K) upside down with
the battery compartment (K2) away from
you as shown in the illustration.
2 Remove the cover (K1) from the bottom of
the keyboard.
3 Insert a battery into the compartment (K2) and
slide the battery to the right. Insert the second
battery. Note the battery images on the inside
of the compartment, and make sure batteries
are placed in the correct direction.
4 Replace the cover.
5 Adjust the keyboard height by lifting the
adjustment legs (K3).
English
Installing the Wireless Keyboard and Mouse Set
3
Getting the Receiver Ready
The receiver (D) must be placed flat on a surface
and positioned properly to avoid interference
from other electrical equipment.
1 Turn off your computer.
2 Connect the receiver cable (D1) to a USB
connector on the front or the back of the
computer.
D1
D
3 Set the receiver flat on a surface and follow
these guidelines:
■
A: Minimum 20 cm (8 inches) clearance
between the receiver and other electronic
devices.
■
B: Maximum 1.5 m (59 inches) distance
between the receiver and wireless mouse
or wireless keyboard.
Installing the Wireless Keyboard and Mouse Set
4
■
C: Minimum 20 cm (8 inches) clearance between the receiver and the monitor.
■
Place no electronic device between the receiver and wireless mouse or wireless keyboard.
English
C
B
B
A
Note:
Installing the Wireless Keyboard and Mouse Set
This is one example of the setup. Other setup positions are also possible.
Warning:
the monitor.
To avoid causing interference, keep the receiver at least 20 cm (8 inches) away from
5
Setting Up the Wireless Set
1 Turn on the computer.
The mouse and keyboard have 255 IDs that are
randomly selected when you press the ID button.
This helps protect against interference from other
wireless devices in the same area.
Important:
The word CONNECT is the label for
the ID button on the bottom of the mouse
and keyboard. To press the ID button, use
a blunt pointed object, like the tip of a
ballpoint pen.
Important: Whenever you want to set the IDs of
both the keyboard and the mouse, you must
first set the receiver ID and mouse ID and
then set the receiver ID and keyboard ID,
as described in this procedure.
Important:
If the ID button is pressed more than
one time during the setup, you must start
over with step 2.
2 On the front of the receiver (D), press the
ID button (E) once.
The blue activity light (J) on the receiver starts
flashing and continues flashing until the next
step is completed or until 30 seconds pass.
E
D
Important:
complete step 3, you must repeat steps 2
and 3 to set the mouse ID. If the ID button
is pressed more than one time during the
mouse setup (step 3), you must start over
with step 2 and set the receiver ID.
F G
If 30 seconds pass before you
H
J
Installing the Wireless Keyboard and Mouse Set
6
3 On the bottom of the mouse, press the
ID button (N) once with a blunt pointed object.
The mouse sends a new ID and flashes the
mouse sensor light (M3) three times. The
receiver flashes the blue activity light (J) three
times and then stops to show it has accepted
the new ID for the mouse.
N
M3
Note:
At this time, when you move the mouse
across a surface, the blue activity light
(J) on the receiver will go on and off
indicating the mouse and the receiver
are working together.
Important:
The mouse goes into a sleep or
suspend mode after 20 minutes of inactivity.
Click a button on the mouse to wake it.
(Moving the mouse does not wake it.)
4 On the front of the receiver, press the ID button
(E) once.
The activity light (J) on the receiver starts
flashing and continues flashing until the next
step is completed or until 30 seconds pass.
E
D
Important:
complete step 5, you must repeat steps
4 and 5 to set the keyboard ID. If the ID
button is pressed more than one time during
the keyboard setup (step 5), you must start
over with step 4 and set the receiver ID.
F G
If 30 seconds pass before you
H
J
English
Installing the Wireless Keyboard and Mouse Set
7
5 On the bottom of the keyboard, press the
ID button (L) once with a blunt pointed object.
The keyboard sends a new ID, and the blue
activity light (J) on the receiver flashes three
times and then stops to show it has accepted
the new ID for the keyboard.
L
K
Note:
After the receiver, mouse, and keyboard
are working, you can separately reset the
ID button for the mouse (N) or the keyboard
(L) after pressing the receiver ID button (E).
Resetting ID Buttons When
Replacing Batteries
When the batteries are replaced in the mouse
or the keyboard, reset the ID buttons on the
receiver and the unit. You must press the receiver
ID button first and then press the mouse or the
keyboard ID button. Refer to the steps in the
section “Setting Up the Wireless Set.”
Note:
8
At this time, when you press a key on the
keyboard or adjust the keyboard volume
knob, the blue activity light (J) on the
receiver goes on and off indicating the
keyboard and the receiver are working
together.
Installing the Wireless Keyboard and Mouse Set
Note:
You can replace the batteries in the mouse
and keyboard without turning off the
computer. The computer must be on when
you change the ID setting on the three units.
Using the Wireless Set
The lights on the receiver (D) indicate:
■
Receiver activity (J)
The blue light flashes when you move or click
the mouse or press any key on the keyboard.
■
Number lock on (F)
■
Caps lock on (G)
■
Scroll lock on (H)
The receiver ID button (E) is on the front of the
receiver.
E
D
F G
H
J
Use the receiver on a nonmetallic surface for
better reception.
The optical mouse uses a light to sense
movement. Use the optical mouse on an opaque
English
surface; the optical mouse cannot work on a
glass, translucent, or reflective surface.
Important:
The mouse goes into a sleep or
suspend mode after 20 minutes of inactivity.
Click a button on the mouse to wake it.
(Moving the mouse does not wake it.)
You may notice that the mouse moves the cursor
on the screen twice as fast as a standard mouse
does. The mouse moves the cursor at 800 dots
per inch (dpi) while a standard mouse moves the
cursor at 400 dpi. Change the cursor movement
speed by using the mouse properties in the
Control Panel.
Installing the Wireless Keyboard and Mouse Set
9
Low Battery Icons
Troubleshooting
The computer displays a keyboard icon or a
mouse icon in the upper-right corner of the screen
to indicate low batteries in that unit.
Note:
The Low Battery icon appears 5 times each
hour until the batteries are changed. If you
use a mouse pad, choose a light-colored
one, not a dark one, to conserve battery
power.
If the wireless mouse or keyboard does not work,
do the following:
■
Check that the receiver cables go to the USB
connector on the front or the back of the
computer.
■
Click a button on the mouse and move it, or
press any key on the keyboard to see if the
blue activity light on the receiver flashes. If it
doesn’t flash, reset the unit:
Press the receiver ID button once, and then
press the mouse ID button once.
Or
Press the receiver ID button once, and then
press the keyboard ID button once.
■
Make sure that the batteries are correctly
installed in the mouse and keyboard.
Installing the Wireless Keyboard and Mouse Set
10
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.