Page 1
User Guide
Page 2
© Copyright 2020 HP Development Company,
L.P.
FreeSync is a trademark of Advanced Micro
Devices, Inc. HDMI, the HDMI Logo and High-
Denition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing
LLC. Windows is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries. VESA® is
a trademark or registered trademark owned by
the Video Electronics Standards Association
(VESA) in the United States and other countries.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
Product notice
This guide describes features that are common
to most models. Some features may not be
available on your product. To access the latest
user guide, go to http://www.hp.com/support,
and follow the instructions to nd your
product. Then select User Guides.
First Edition: May 2020
Document Part Number: L97901-001
Page 3
About this guide
This guide provides technical specications and information about monitor features, setting up the monitor,
and using the software. Depending on the model, your monitor may not have all the features included in this
guide.
WARNING! Indicates a hazardous situation that, if not avoided, could result in serious injury or death.
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
IMPORTANT: Indicates information considered important but not hazard-related (for example, messages
related to property damage). Warns the user that failure to follow a procedure exactly as described could
result in loss of data or in damage to hardware or software. Also contains essential information to explain a
concept or to complete a task.
NOTE: Contains additional information to emphasize or supplement important points of the main text.
TIP: Provides helpful hints for completing a task.
This product incorporates HDMI technology.
iii
Page 4
iv About this guide
Page 5
Table of contents
1 Getting started ............................................................................................................................................. 1
Important safety information ............................................................................................................................... 1
Product features and components ........................................................................................................................ 2
Features ............................................................................................................................................... 2
Front components ............................................................................................................................... 3
Rear and side components .................................................................................................................. 4
Setting up the monitor .......................................................................................................................................... 5
Attaching the monitor stand ............................................................................................................... 5
Mounting the monitor head ................................................................................................................ 6
Removing the monitor stand ............................................................................................ 6
Attaching the monitor head to a mounting device (select products only) ....................... 7
Connecting the cables ......................................................................................................................... 8
Adjusting the monitor ....................................................................................................................... 10
Installing a security cable ................................................................................................................. 10
Turning on the monitor ..................................................................................................................... 11
HP watermark and image retention policy (select products only) ................................................... 11
2 Using the monitor ........................................................................................................................................ 12
Downloading software and utilities .................................................................................................................... 12
The Information le ............................................................................................................................................. 12
The Image Color Matching le ............................................................................................................................. 12
Using the OSD menu ............................................................................................................................................ 13
Using the function buttons .................................................................................................................................. 14
Reassigning the function buttons ....................................................................................................................... 14
Using Auto-Sleep Mode ....................................................................................................................................... 14
Adjusting blue light output .................................................................................................................................. 15
3 Support and troubleshooting ........................................................................................................................ 16
Solving common issues ....................................................................................................................................... 16
Button lockouts ................................................................................................................................................... 17
Using the auto-adjustment function (analog input) ........................................................................................... 17
Optimizing image performance (analog input) ................................................................................................... 18
Contacting support .............................................................................................................................................. 19
Preparing to call technical support ..................................................................................................................... 19
Locating the serial number and product number ............................................................................................... 20
v
Page 6
4 Maintaining the monitor .............................................................................................................................. 21
Maintenance guidelines ....................................................................................................................................... 21
Cleaning the monitor ......................................................................................................................... 21
Shipping the monitor ......................................................................................................................... 22
Appendix A Technical specications ................................................................................................................. 23
68.6 cm (27.0 in) model specications ............................................................................................................... 23
61.0 cm (24.0 in) model specications ............................................................................................................... 23
60.5 cm (23.8 in) model specications ............................................................................................................... 24
54.6 cm (21.5 in) model specications ............................................................................................................... 25
52.6 cm (20.7 in) model specications ............................................................................................................... 25
49.5 cm (19.5 in) model specications ............................................................................................................... 26
47.0 cm (18.5 in) model specications ............................................................................................................... 26
Preset display resolutions ................................................................................................................................... 27
68.6 cm (27.0 in) models .................................................................................................................. 27
61.0 cm (24.0 in) models .................................................................................................................. 28
60.5 cm (23.8 in) models .................................................................................................................. 28
54.6 cm (21.5 in) models .................................................................................................................. 29
52.6 cm (20.7 in) models .................................................................................................................. 29
49.5 cm (19.5 in) models .................................................................................................................. 30
47.0 cm (18.5 in) models .................................................................................................................. 30
Preset timing resolutions .................................................................................................................................... 30
Energy saver feature ........................................................................................................................................... 31
Appendix B Accessibility ................................................................................................................................. 32
HP and accessibility ............................................................................................................................................. 32
Finding the technology tools you need ............................................................................................ 32
The HP commitment ......................................................................................................................... 32
International Association of Accessibility Professionals (IAAP) ....................................................... 32
Finding the best assistive technology .............................................................................................. 33
Assessing your needs ..................................................................................................... 33
Accessibility for HP products .......................................................................................... 33
Standards and legislation .................................................................................................................................... 34
Standards .......................................................................................................................................... 34
Mandate 376 – EN 301 549 ............................................................................................ 34
Web Content Accessibility Guidelines (WCAG) ................................................................ 34
Legislation and regulations .............................................................................................................. 34
Useful accessibility resources and links .............................................................................................................. 35
Organizations .................................................................................................................................... 35
Educational institutions .................................................................................................................... 35
vi
Page 7
Other disability resources ................................................................................................................. 35
HP links .............................................................................................................................................. 35
Contacting support .............................................................................................................................................. 36
vii
Page 8
viii
Page 9
1 Getting started
Important safety information
A power cord is included with the monitor. If you use another cord, use only a power source and connection
appropriate for this monitor. For information about the correct power cord set to use with the monitor, see
Product Notices provided in your documentation kit.
the
WARNING! To reduce the risk of electric shock or damage to the equipment:
● Plug the power cord into an AC outlet that is easily accessible at all times.
● If the power cord has a 3-pin attachment plug, plug the cord into a grounded (earthed) 3-pin outlet.
● Disconnect power from the computer by unplugging the power cord from the AC outlet. When
unplugging the power cord from the AC outlet, grasp the cord by the plug.
For your safety, do not place anything on power cords or cables. Care should be taken to route all cords and
cables connected to the monitor so that they cannot be stepped on, pulled, grabbed, or tripped over.
To reduce the risk of serious injury, read the Safety & Comfort Guide provided with your user guides. It
describes proper workstation setup and proper posture, health, and work habits for computer users. The
Safety & Comfort Guide also provides important electrical and mechanical safety information. The Safety &
Comfort Guide is also available on the Web at http://www.hp.com/ergo.
IMPORTANT: For the protection of the monitor and the computer, connect all power cords for the computer
and its peripheral devices (such as a monitor, printer, scanner) to a surge protection device such as a power
strip or uninterruptible power supply (UPS). Not all power strips provide surge protection; the power strip
must be specically labeled as having this capability. Use a power strip whose manufacturer oers a damage
replacement policy so that you can replace the equipment if surge protection fails.
Use the appropriate and correctly sized furniture designed to properly support your monitor.
WARNING! Monitors that are inappropriately situated on dressers, bookcases, shelves, desks, speakers,
chests, or carts could fall over and cause personal injury.
NOTE: This product is suitable for entertainment purposes. Consider placing the monitor in a controlled
luminous environment to avoid interference from surrounding light and bright surfaces that might cause
disturbing reections from the screen.
Important safety information 1
Page 10
Product features and components
Features
Depending on the model, your monitor might include the following features:
● The following models, which include full-screen support for lower resolutions; includes custom scaling
for maximum image size while preserving original aspect ratio:
– 68.6 cm (27.0 in) diagonal viewable screen area with 1920 × 1080 resolution
– 61.0 cm (24.0 in) diagonal viewable screen area with 1920 × 1080 resolution
– 60.5 cm (23.8 in) diagonal viewable screen area with 1920 × 1080 resolution
– 54.6 cm (21.5 in) diagonal viewable screen area with 1920 × 1080 resolution
– 52.6 cm (20.7 in) diagonal viewable screen area with 1920 × 1080 resolution
– 49.5 cm (19.5 in) diagonal viewable screen area with 1600 × 900 resolution
– 47.0 cm (18.5 in) diagonal viewable screen area with 1366 × 768 resolution
● In-plane switching (IPS) or twisted nematic (TN) panel
● Nonglare panel with an LED backlight
● Wide viewing angle on IPS models to allow viewing from a sitting or standing position, or moving from
side to side (select products only)
● Tilt adjustment capability
● Removable stand for exible monitor head mounting solutions
● High-Denition Multimedia Interface™ (HDMI) video input (select products only; cable included in select
regions)
● VGA video input (cable included in select regions)
● Audio-in jack (P21 models only)
● Four on-screen display (OSD) buttons, three that you can recongure to quickly allow selection of the
most commonly used operations
● Plug and Play capability if supported by your operating system
● VESA® mounting bracket for attaching the monitor head to a wall-mount device or swing arm (select
products only)
● Security cable slot on the rear of the monitor for an optional security cable
● On-screen adjustments in several languages for easy setup and screen optimization
● Support for FreeSync™, an Adaptive-Sync technology, to reduce stuttering and tearing in games and
videos by locking the monitor’s refresh rate to the frame rate of a compatible graphics card (select
products only).
NOTE: Adaptive refresh rates vary by display.
● Energy saver feature to meet requirements for reduced power consumption
2 Chapter 1 Getting started
Page 11
NOTE: For safety and regulatory information, see the Product Notices provided in your documentation kit.
To access the latest user guide, go to http://www.hp.com/support, and follow the instructions to nd your
product. Then select Manuals.
Front components
Table 1-1 Front components and their descriptions
Component Description
(1) Menu button Press to open the OSD menu and select a menu item from the OSD.
(2) OSD buttons
(assignable)
(3) Power button Turns the monitor on or o.
(4) Power light White: The monitor is on.
When the OSD menu is open, press the buttons to navigate through the menu. The
function light icons indicate the default button functions. For a description of these
functions, see Using the function buttons on page 14.
You can reassign the function buttons to quickly select the most commonly used
operations. See Reassigning the function buttons on page 14.
Amber: Monitor is in a reduced power state because of inactivity. See Using Auto-
Sleep Mode on page 14.
Product features and components 3
Page 12
Rear and side components
Table 1-2 Rear and side components and their descriptions
Component Description
(1) Power connector Connects the power cord.
(2) Stand release button Releases the stand from the monitor.
(3) HDMI port (select products only) Connects the HDMI cable to a source device such as a computer or game console.
(4) VGA connector Connects the VGA cable to the source device.
(5) Audio-in jack (select products only) Connects the audio cable to the monitor.
(6) Security cable slot Connects an optional security cable.
4 Chapter 1 Getting started
Page 13
Setting up the monitor
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
workstation setup and proper posture, health, and work habits for computer users. The Safety & Comfort
Guide also provides important electrical and mechanical safety information. The Safety & Comfort Guide is
available on the Web at http://www.hp.com/ergo.
IMPORTANT: To prevent damage to the monitor, do not touch the surface of the LCD panel. Pressure on the
panel may cause nonuniformity of color or disorientation of the liquid crystals. If this occurs, the screen will
not recover to its normal condition.
IMPORTANT: To prevent the screen from getting scratched, defaced, or broken and to prevent damage to
the control buttons, position the monitor facedown on a at surface covered with protective sheet foam or a
nonabrasive cloth.
Attaching the monitor stand
TIP: Consider the placement of the monitor, because surrounding light and bright surfaces might cause
interfering reections.
NOTE: The procedures for attaching a monitor stand might be dierent on other models.
1. Position the monitor head facedown on a at surface covered by protective sheet made of foam or a
clean, dry cloth.
2. Slide the stand into the recess on the back of the panel (1).
3. Insert the base into the bottom of the stand (2).
Setting up the monitor 5
Page 14
Mounting the monitor head
The monitor head can be attached to a wall, swing arm, or other mounting xture.
IMPORTANT: This monitor supports the VESA industry-standard 100 mm mounting holes. To attach a third-
party mounting solution to the monitor head, use four 4 mm, 0.7 pitch, and 10 mm long screws. Longer
screws might damage the monitor. Be sure to verify that the manufacturer’s mounting solution is compliant
with the VESA standard and is rated to support the weight of the monitor head. For best performance, use the
power and video cables provided with the monitor.
NOTE: This apparatus is intended to be supported by a UL-listed or CSA-listed wall-mount bracket.
Removing the monitor stand
IMPORTANT: Before disassembling the monitor, be sure that the monitor is turned o and all cables are
disconnected.
1. Disconnect and remove all cables from the monitor.
2. Position the monitor facedown on a at surface covered by protective sheet made of foam or a clean,
dry cloth.
3. Push up the latch near the bottom center of the stand’s mounting plate (1).
4. Slide the stand out of the recess (2).
6 Chapter 1 Getting started
Page 15
Attaching the monitor head to a mounting device (select products only)
1. Remove the four screws from the VESA holes located on the rear of the monitor head.
2. To attach the monitor head to a swing arm or other mounting device, insert four mounting screws
through the holes on the mounting device and into the VESA screw holes on the back of the monitor
head.
IMPORTANT: If these instructions do not apply to your device, then follow the mounting device
manufacturer’s instructions when mounting the monitor to a wall or swing arm.
Setting up the monitor 7
Page 16
Connecting the cables
NOTE: Depending on the model, the monitor may be capable of supporting VGA or HDMI inputs. The video
mode is determined by the video cable used. The monitor automatically determines which inputs have valid
video signals. The inputs can be selected through the OSD menu. The monitor ships with select cables. Not all
cables shown in this section are included with the monitor.
1. Place the monitor in a convenient, well-ventilated location near the computer.
2. Connect a video cable.
NOTE: The monitor automatically determines which inputs have valid video signals.
● Connect one end of a VGA cable to the VGA port on the rear of the monitor and the other end to the
VGA port on the source device.
● Connect one end of an HDMI cable to the HDMI port on the rear of the monitor and the other end to
the HDMI port on the source device.
8 Chapter 1 Getting started
Page 17
3. To enable sound from the monitor’s speakers, connect one end of an audio cable to the audio-in jack on
the monitor and the other end to the audio-out jack on the source device (select products only).
4. Connect one end of the power cord to the power connector on the rear of the monitor and the other end
to a grounded AC outlet.
WARNING! To reduce the risk of electric shock or damage to the equipment:
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord into a grounded (earthed) AC outlet that is easily accessible at all times.
Disconnect power from the equipment by unplugging the power cord from the AC outlet.
For your safety, do not place anything on power cords or cables. Arrange them so that no one may
accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging the power cord
from the AC outlet, grasp the cord by the plug.
Setting up the monitor 9
Page 18
Adjusting the monitor
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
workstation setup and proper posture, health, and work habits for computer users. The Safety & Comfort
Guide also provides important electrical and mechanical safety information. The Safety & Comfort Guide is
available on the Web at http://www.hp.com/ergo.
▲ Tilt the monitor head forward or backward to set it to a comfortable eye level.
Installing a security cable
You can secure the monitor to a xed object with an optional security cable available from HP. Use the key
provided to attach and remove the lock.
10 Chapter 1 Getting started
Page 19
Turning on the monitor
IMPORTANT: Burn-in image damage may occur on monitors that display the same static image on the
screen for 12 or more hours. To avoid burn-in image damage, you should always activate a screen saver
application or turn o the monitor when it will not be in use for a prolonged period of time. Image retention is
a condition that may occur on all LCD screens. Burn-in damage on the monitor is not covered under the HP
warranty.
NOTE: If pressing the power button has no eect, the Power Button Lockout feature might be enabled. To
disable this feature, press and hold the monitor power button for 10 seconds.
NOTE: On select HP monitors, you can disable the power light in the OSD menu. Press the Menu button to
open the OSD, select Power, select Power LED, and then select O.
▲ Press the power button on the monitor to turn it on.
When the monitor is rst turned on, a monitor status message is displayed for 5 seconds. The message shows
which input is the current active signal, the status of the auto-switch source setting (On or O; default setting
is On), the current preset display resolution, and the recommended preset display resolution.
The monitor automatically scans the signal inputs for an active input and uses that input for the display.
HP watermark and image retention policy (select products only)
The IPS monitor models are designed with In-Plane Switching (IPS) display technology, which provides ultrawide viewing angles and advanced image quality. IPS monitors are suitable for a wide variety of advanced
image quality applications. This panel technology, however, is not suitable for applications that exhibit static,
stationary, or xed images for long periods of time without the use of screen savers. These types of
applications may include camera surveillance, video games, marketing logos, and templates. Static images
may cause image retention damage that could look like stains or watermarks on the monitor’s screen.
Image retention damage on monitors that are in use 24 hours per day is not covered under the HP warranty.
To avoid image retention damage, always turn o the monitor when it is not in use, or use the power
management setting, if supported on your system, to turn o the monitor when the system is idle.
Setting up the monitor 11
Page 20
2 Using the monitor
Downloading software and utilities
You can download and install the following les from http://www.hp.com/support:
● INF (Information) le
● ICM (Image Color Matching) les
To download the les:
1. Go to http://www.hp.com/support.
2. Select Software and Drivers.
3. Select your product type.
4. Enter your HP monitor model in the search eld and follow the on-screen instructions.
The Information le
The INF le denes monitor resources used by Windows® operating systems to ensure monitor compatibility
with the computer’s graphics adapter.
This monitor is Windows Plug and Play compatible, and the monitor will work correctly without installing the
INF le. Monitor Plug and Play compatibility requires that the computer’s graphics card is VESA DDC2compliant and that the monitor connects directly to the graphics card. Plug and Play does not work through
separate BNC-type connectors or through distribution buers, boxes, or both.
The Image Color Matching le
The ICM les are data les that are used in conjunction with graphics programs to provide consistent color
matching from monitor screen to printer, or from scanner to monitor screen. These les are activated from
within graphics programs that support this feature.
NOTE: The ICM color prole is written in accordance with the International Color Consortium (ICC) Prole
Format specication.
12 Chapter 2 Using the monitor
Page 21
Using the OSD menu
Use the OSD menu to adjust the screen image based on your viewing preferences. To access and make
adjustments in the OSD:
● Use the buttons at the bottom of the monitor’s front bezel.
To access the OSD menu and make adjustments:
1. If the monitor is not already on, press the power button to turn on the monitor.
2. Press the Menu button.
3. Use the three function buttons to navigate, select, and adjust the menu choices. The on-screen button
labels vary, depending on which menu or submenu is active.
The following table lists possible menu selections in the OSD main menu.
Table 2-1 OSD menu options and descriptions
Main menu Description
Brightness+ Adjusts the brightness, contrast, and black stretch levels of the screen.
Color Selects and adjusts the screen color.
Image Adjusts the screen image.
Input Selects the video input signal (VGA or HDMI).
Power Adjusts the power settings.
Menu Adjusts the on-screen display (OSD) menu and function button controls.
Management Adjusts the DDC/CI settings, selects the language in which the OSD menu is displayed (the factory default
is English), adjusts the audio settings, and returns all OSD menu settings to the factory default settings.
Information Selects and displays important information about the monitor.
Exit Exits the OSD menu screen.
Using the OSD menu 13
Page 22
Using the function buttons
Pressing one of the function buttons activates the buttons and lights the icons above the buttons.
NOTE: The actions of the function buttons vary among monitor models.
For information about changing the function of the buttons, see Reassigning the function buttons
on page 14.
Table 2-2 Button names and descriptions
Button Description
(1) Menu button Opens the OSD main menu, selects a menu item from the OSD, or closes the OSD
menu.
(2) Brightness+ button
Assignable function button
(3) Color button
Assignable function button
(4) Next Input or Next Active Input
button
Assignable function button
Opens the Brightness+ adjustment scale.
Opens the Color menu where you can adjust the monitor screen to a comfortable
viewing light or select a preset view mode.
Switches the monitor’s input source to the next active input.
Reassigning the function buttons
You can change the assignable function buttons from their default values so that when the buttons are
activated, you can quickly access commonly used menu items. You cannot reassign the Menu button.
To reassign the function buttons:
1. Press the Menu button to open the OSD menu.
2. Select Menu, select Assign Buttons, and then select one of the available options for the button that you
want to assign.
Using Auto-Sleep Mode
The monitor supports an OSD menu option called Auto-Sleep Mode that allows you to enable or disable a
reduced power state for the monitor. When Auto-Sleep Mode is enabled (enabled by default), the monitor
enters a reduced power state when the computer signals low power mode (absence of either horizontal or
vertical sync signal).
Upon entering this reduced power state (sleep mode), the monitor screen is blanked, the backlight turns o,
and the power light turns amber. The monitor draws less than 0.5 W of power when in this reduced power
state. The monitor wakes from sleep mode when the computer sends an active signal to the monitor (for
example, if you activate the mouse or keyboard).
14 Chapter 2 Using the monitor
Page 23
To disable Auto-Sleep Mode in the OSD:
1. Press the Menu button to open the OSD.
2. In the OSD, select Power.
3. Select Auto-Sleep Mode, and then select O.
Adjusting blue light output
Decreasing the blue light emitted by the monitor reduces the blue light exposure to your eyes. This monitor
allows you to select a setting to reduce blue light output and create a more relaxing and less stimulating
image while you read content on the screen.
To adjust the blue light output from the monitor:
1. Press one of the OSD buttons to activate the buttons, and then press the Menu button to open the OSD.
Select Color.
2. Select a setting.
● Low Blue Light: (TÜV certied) Reduces blue light for improved eye comfort.
● Night: Adjusts to the lowest blue light and reduces the impact on sleep.
● Reading: Optimizes blue light and brightness for indoor viewing.
3. Select Save and Return to save your setting and close the menu. Select Cancel if you do not want to
save the setting.
4. In the Main menu, select Exit.
Adjusting blue light output 15
Page 24
3 Support and troubleshooting
Solving common issues
The following table lists possible issues, the possible cause of each issue, and the recommended solutions.
Table 3-1 Common issues and solutions
Issues Possible cause Solution
Screen is blank or video is
ashing.
Image appears blurred,
indistinct, or too dark.
“Check Video Cable” is
displayed on the screen.
“Input Signal Out of Range” is
displayed on screen.
Power cord is disconnected. Connect the power cord.
Monitor is o. Press the monitor power button.
NOTE: If pressing the power button has no eect, press and
hold the power button for 10 sec to disable the Power Button
Lockout feature.
Video cable is improperly connected. Connect the video cable properly. For more information, see
Connecting the cables on page 8.
System is in Auto-Sleep Mode. Press any key on the keyboard or move the mouse to
inactivate the screen blanking utility.
Video card is incompatible. Open the OSD menu and select the Input menu. Set Auto-
Switch Input to O and manually select the input.
or
Replace the video card or connect the video cable to one of
the computer’s on-board video sources.
Brightness setting is too low. Open the OSD menu, and select Brightness to adjust the
brightness scale as needed.
Monitor video cable is disconnected. Connect the appropriate video signal cable between the
computer and monitor. Be sure that the computer power is o
while connecting the video cable.
Video resolution and/or refresh rate
are set higher than the monitor
supports.
Change the settings to a supported setting (see Preset display
resolutions on page 27).
The monitor does not enter
into a low-power sleep state.
“OSD Lockout” is displayed. The monitor's OSD Lockout function
“Power Button Lockout” is
displayed.
FreeSync is enabled in
monitor OSD, but refresh rate
does not vary.
The monitor's power saving control is
disabled.
is enabled.
The monitor's Power Button Lockout
feature is enabled.
Variable refresh rate (VRR) might be
disabled in the graphics card
software.
The refresh rate might be set too low. In Windows, set the refresh rate to its maximum setting.
Content and/or hardware might not
be VRR capable.
16 Chapter 3 Support and troubleshooting
Open the OSD menu and select Power, select Auto-Sleep
Mode, and then set auto-sleep to On.
Press and hold the Menu button for 10 sec to disable the OSD
Lockout function.
Press and hold the Power button for 10 sec to unlock the
power button function.
Enable VRR in your graphics card software.
Verify the content being displayed is VRR capable.
Page 25
Table 3-1 Common issues and solutions (continued)
Issues Possible cause Solution
Be sure that a computer with an AMD Radeon graphics card or
a AMD A-Series processor is connected to the monitor using a
DisplayPort or HDMI cable.
The monitor is experiencing
screen tearing.
FreeSync might not be enabled. Open the OSD and enable FreeSync.
Button lockouts
Holding down the power button or Menu button for 10 seconds disables that button. You can re-enable the
button by holding the button down again for 10 seconds. The button lockout function is available only when
the monitor is on, an active signal is displayed, and the OSD menu is closed.
Using the auto-adjustment function (analog input)
The auto-adjustment feature automatically engages and attempts to optimize your screen under the
following conditions:
● Monitor setup
● Factory reset of the computer
● Changing monitor resolution
You can manually optimize the screen performance for the VGA (analog) input at any time from the Auto
Adjustment menu in the OSD. You can download the auto-adjustment pattern software utility from
http://www.hp.com/support.
Do not use this procedure if the monitor is using an input other than VGA. If the monitor is using a VGA
(analog) input, this procedure can correct the following image quality conditions:
● Fuzzy or unclear focus
● Ghosting, streaking, or shadowing eects
● Faint vertical bars
● Thin, horizontal scrolling lines
● An o-center picture
To use the auto-adjustment feature:
1. Turn the monitor on, and then wait for 20 minutes before adjusting.
2. Press the Menu button to open the OSD menu, select Image, and then select Auto-Adjustment. If the
result is not satisfactory, continue with the procedure.
Button lockouts 17
Page 26
3. Open the auto-adjustment utility. (You can download this utility from http://www.hp.com/support.) The
setup test pattern is displayed.
4. Press the esc key or any other key on the keyboard to exit the test pattern.
Optimizing image performance (analog input)
You can adjust two controls in the on-screen display to improve image performance: Clock and Phase
(available in the OSD menu). Use these controls only when the auto-adjustment function does not provide a
satisfactory image.
NOTE: The Clock and Phase controls are adjustable only when you use an analog (VGA) input. These controls
are not adjustable for digital inputs.
The Clock must rst be set correctly because the Phase settings are dependent on the main Clock setting.
● Clock: Increases or decreases the value to minimize any vertical bars or stripes visible on the screen
background.
● Phase: Increases or decreases the value to minimize video ickering or blurring.
NOTE: When using the controls, you will obtain the best results by using the auto-adjustment pattern
software utility. You can download this utility from http://www.hp.com/support.
When adjusting the Clock and Phase values, if the monitor images become distorted, continue adjusting the
values until the distortion disappears. To restore the factory settings, press the Menu button to open the OSD
menu, then select Management, select Factory Reset, and select Yes.
To eliminate vertical bars (Clock):
1. Press the Menu button to open the OSD menu, select Image, and then select Clock and Phase.
2. Select Clock, and then use the OSD buttons on the monitor that display up and down arrow icons to
eliminate vertical bars. Press the buttons slowly so that you do not miss the optimum adjustment point.
3. After adjusting the Clock, if ickering, blurring, or bars appear on the screen, proceed to adjust the
Phase.
To remove ickering or blurring (Phase):
18 Chapter 3 Support and troubleshooting
Page 27
1. Press the Menu button to open the OSD menu, select Image, and then select Clock and Phase.
2. Select Phase, and then use the OSD buttons on the monitor that display up and down arrow icons to
eliminate ickering or blurring. Flickering or blurring may not be eliminated, depending on the computer
or graphics controller card installed.
To correct screen position (Horizontal Position or Vertical Position):
1. Press the Menu button to open the OSD menu, select Image, and then select Image Position.
2. Press the OSD buttons on the monitor that display up and down arrow icons to properly adjust the
position of the image in the display area of the monitor. The Horizontal Position shifts the image left or
right; the Vertical Position shifts the image up or down.
Contacting support
To resolve a hardware or software problem, go to http://www.hp.com/support. Use this site to get more
information about your product, including links to discussion forums and instructions on troubleshooting. You
can also nd information about how to contact HP and open a support case.
NOTE: Contact customer support to replace the power cord or any other cables that shipped with your
monitor.
Preparing to call technical support
If you cannot solve a problem using the troubleshooting tips in this section, you may need to call technical
support. Have the following information available when you call:
● Monitor model number
● Monitor serial number
● Purchase date on invoice
● Conditions under which the problem occurred
● Error messages received
● Hardware conguration
● Name and version of the hardware and software you are using
Contacting support 19
Page 28
Locating the serial number and product number
Depending on the product, the serial number and product number are located on a label on the rear of the
monitor or on a label under the front bezel of the monitor head. You might need these numbers when
contacting HP about the monitor.
20 Chapter 3 Support and troubleshooting
Page 29
4 Maintaining the monitor
Maintenance guidelines
To enhance the performance and extend the life of the monitor:
● Do not open the monitor cabinet or attempt to service this product yourself. Adjust only those controls
that are covered in the operating instructions. If the monitor is not operating properly or has been
dropped or damaged, contact an authorized HP dealer, reseller, or service provider.
● Use only a power source and connection appropriate for this monitor, as indicated on the label or back
plate of the monitor.
● Be sure that the total ampere rating of the products connected to the outlet does not exceed the current
rating of the AC outlet and that the total ampere rating of the products connected to the cord does not
exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A) for
each device.
● Install the monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug
rmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord.
● Turn the monitor o when it is not in use and use a screen saver program. Doing this can substantially
increase the life expectancy of the monitor.
NOTE: A burned-in image on the monitor is not covered under the HP warranty.
● Never block the slots and openings of the cabinet or push objects into them. These openings provide
ventilation.
● Do not drop the monitor or place it on an unstable surface.
● Do not allow anything to rest on the power cord. Do not walk on the cord.
● Keep the monitor in a well-ventilated area, away from excessive light, heat, or moisture.
Cleaning the monitor
1. Turn o the monitor and unplug the power cord from the AC outlet.
2. Disconnect any external devices.
3. Dust the monitor by wiping the screen and the cabinet with a soft, clean antistatic cloth.
4. For more diicult cleaning situations, use a 50/50 mix of water and isopropyl alcohol.
IMPORTANT: Do not use cleaners that contain petroleum-based materials such as benzene, thinner, or
any volatile substance to clean the monitor screen or cabinet. These chemicals may damage the
monitor.
IMPORTANT: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface.
Never spray the cleaner directly on the screen surface. It may run behind the bezel and damage the
electronics. The cloth should be moist, but not wet. Water dripping into the ventilation openings or other
points of entry can cause damage to the monitor. Allow the monitor to air-dry before use.
Maintenance guidelines 21
Page 30
Shipping the monitor
Keep the original packing box in a storage area. You may need it later if you ship the monitor or move.
22 Chapter 4 Maintaining the monitor
Page 31
A Technical specications
NOTE: All specications represent the typical specications provided by HP component manufacturers;
actual performance may vary either higher or lower.
For the latest specications or additional specications for this product, go to http://www.hp.com/go/
quickspecs/ and search for your specic monitor model to nd the model-specic QuickSpecs.
68.6 cm (27.0 in) model specications
Table A-1 68.6 cm (27.0 in) monitor specications
Specication Measurement
Display, wide screen
Type
Viewable image size 68.6 cm diagonal 27.0 in diagonal
Maximum weight (unpacked) 4.5 kg 9.92 lb
Dimensions (include base)
Height
Depth
Width
Tilt adjustment range –5° to 20°
Environmental requirements
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port
68.6 cm
IPS
44.77 cm
20.00 cm
61.22 cm
5°C to 35°C
–20°C to 60°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
27.0 in
17.63 in
7.87 in
24.10 in
41°F to 95°F
–4°F to 140°F
61.0 cm (24.0 in) model specications
A-2 61.0 cm (24.0 in) model specications
Table
Specication Measurement
Display, wide-screen
Type
Viewable image size 61.0 cm diagonal 24.0 in diagonal
Maximum weight (unpacked, with stand) 3.3 kg 7.28 lbs
61.0 cm
TN
24.0 in
68.6 cm (27.0 in) model specications 23
Page 32
Table A-2 61.0 cm (24.0 in) model specications (continued)
Specication Measurement
Dimensions (include base)
Height
Depth
Width
Tilt adjustment range –5° to 20°
Environmental requirements temperature
41.96 cm
18.60 cm
56.86 cm
16.52 in
7.32 in
22.39 in
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port
5°C to 35°C
–20°C to 60°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
60.5 cm (23.8 in) model specications
Table
A-3 60.5 cm (23.8 in) model specications
Specication Measurement
Display, wide-screen
Type
Viewable image size 60.5 cm diagonal 23.8 in diagonal
Maximum weight (unpacked, with stand) 3.5 kg 7.72 lbs
Dimensions (include base)
Height
Depth
Width
60.5 cm
IPS
40.50 cm
18.60 cm
53.96 cm
41°F to 95°F
–4°F to 140°F
23.8 in
15.94 in
7.32 in
21.24 in
Tilt adjustment range –5° to 20°
Environmental requirements temperature
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port
24 Appendix A Technical specications
5°C to 35°C
–20°C to 60°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
41°F to 95°F
–4°F to 140°F
Page 33
54.6 cm (21.5 in) model specications
Table A-4 54.6 cm (21.5 in) model specications
Specication Measurement
Display, wide-screen
Type
Viewable image size 54.6 cm diagonal 21.5 in diagonal
Maximum weight (unpacked, with stand) 2.85 kg 6.28 lbs
Dimensions (include base)
Height
Depth
Width
Tilt adjustment range –5° to 20°
Environmental requirements temperature
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port
54.6 cm
TN
38.1 cm
18.1 cm
50.5 cm
5°C to 35°C
–40°C to 65°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
21.5 in
15.01 in
7.12 in
19.88 in
41°F to 95°F
–40°F to 149°F
52.6 cm (20.7 in) model specications
Table
A-5 52.6 cm (20.7 in) model specications
Specication Measurement
Display, wide-screen
Type
Viewable image size 52.6 cm diagonal 20.7 in diagonal
Maximum weight (unpacked, with stand) 2.6 kg 5.73 lbs
Dimensions (include base)
Height
Depth
Width
Tilt adjustment range –5° to 20°
Environmental requirements temperature
Operating temperature
Storage temperature
52.6 cm
TN
37.41 cm
18.60 cm
49.03 cm
5°C to 35°C
–20°C to 60°C
20.7 in
14.73 in
7.32 in
19.30 in
41°F to 95°F
–4°F to 140°F
54.6 cm (21.5 in) model specications 25
Page 34
Table A-5 52.6 cm (20.7 in) model specications (continued)
Specication Measurement
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port (select
5% to 95% (noncondensing)
20% to 80% (noncondensing)
products only)
49.5 cm (19.5 in) model specications
Table A-6 49.5 cm (19.5 in) model specications
Specication Measurement
Display, wide-screen
Type
Viewable image size 49.5 cm diagonal 19.5 in diagonal
Maximum weight (unpacked, with stand) 2.81 kg 6.19 lbs
Dimensions (include base)
Height
Depth
Width
49.5 cm
TN
35.36 cm
19.00 cm
46.26 cm
19.5 in
13.92 in
7.48 in
18.21 in
Tilt adjustment range –5° to 25°
Environmental requirements temperature
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
Input terminal One HDMI port, one VGA port
5°C to 35°C
–40°C to 65°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
47.0 cm (18.5 in) model specications
A-7 47.0 cm (18.5 in) model specications
Table
Specication Measurement
Display, wide-screen
Type
Viewable image size 47.0 cm diagonal 18.5 in diagonal
Maximum weight (unpacked, with stand) 2.45 kg 5.4 lbs
47.0 cm
TN
41°F to 95°F
–40°F to 149°F
18.5 in
26 Appendix A Technical specications
Page 35
Table A-7 47.0 cm (18.5 in) model specications (continued)
Specication Measurement
Dimensions (include base)
Height
Depth
Width
Tilt adjustment range –5° to 22°
Environmental requirements temperature
Operating temperature
Storage temperature
Storage humidity
Operating humidity
Power source 100 V ac to 240 V ac 50/60 Hz
34.58 cm
15.70 cm
44.14 cm
5°C to 35°C
–40°C to 65°C
5% to 95% (noncondensing)
20% to 80% (noncondensing)
13.61 in
6.18 in
17.38 in
41°F to 95°F
–40°F to 149°F
Input terminal One HDMI port (select products only), one
Preset display resolutions
The following display resolutions are the most commonly used modes and are set as factory defaults. This
monitor automatically recognizes these preset modes, and they will appear properly sized and centered on
the screen.
68.6 cm (27.0 in) models
Table
A-8 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1280 × 800 49.702 59.810
VGA port
7 1280 × 1024 63.981 60.020
8 1440 × 900 55.935 59.887
9 1600 × 900 60.000 60.000
10 1680 × 1050 65.290 59.954
11 1920 × 1080 67.500 60.000
Preset display resolutions 27
Page 36
61.0 cm (24.0 in) models
Table A-9 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 640 × 480 37.500 75.000
3 720 × 400 31.469 70.087
4 800 × 600 37.879 60.317
5 800 × 600 46.875 75.000
6 1024 × 768 48.363 60.004
7 1024 × 768 60.023 75.029
8 1280 × 720 45.000 60.000
9 1280 × 720 55.894 74.925 (HDMI)
10 1280 × 800 49.702 59.810
11 1280 × 800 62.795 74.934 (HDMI)
12 1280 × 1024 63.981 60.020
13 1280 × 1024 79.976 75.025
14 1440 × 900 55.935 59.887
15 1440 × 900 70.635 74.984 (HDMI)
16 1600 × 900 60.000 60.000
17 1680 × 1050 65.290 59.954
18 1920 × 1080 67.500 60.000
19 1920 × 1080 83.894 74.973
60.5 cm (23.8 in) models
Table
A-10 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1280 × 800 49.702 59.810
7 1280 × 1024 63.981 60.020
8 1440 × 900 55.935 59.887
28 Appendix A Technical specications
Page 37
Table A-10 Preset display resolutions (continued)
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
9 1600 × 900 60.000 60.000
10 1680 × 1050 65.290 59.954
11 1920 × 1080 67.500 60.000
54.6 cm (21.5 in) models
Table A-11 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1280 × 800 49.702 59.810
7 1280 × 1024 63.981 60.020
8 1440 × 900 55.935 59.887
9 1600 × 900 60.000 60.000
10 1680 × 1050 65.290 59.954
11 1920 × 1080 67.500 60.000
52.6 cm (20.7 in) models
Table
A-12 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1280 × 800 49.702 59.810
7 1280 × 1024 63.981 60.020
8 1440 × 900 55.935 59.887
9 1600 × 900 60.000 60.000
Preset display resolutions 29
Page 38
Table A-12 Preset display resolutions (continued)
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
10 1680 × 1050 65.290 59.954
11 1920 × 1080 67.500 60.000
49.5 cm (19.5 in) models
Table A-13 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1280 × 800 49.702 59.810
7 1280 × 1024 63.981 60.020
8 1366 × 768 60.000 60.000
9 1440 × 900 55.935 59.887
10 1600 × 900 60.000 60.000
47.0 cm (18.5 in) models
Table
A-14 Preset display resolutions
Preset Pixel format Horz freq (kHz) Vert freq (Hz)
1 640 × 480 31.469 59.940
2 720 × 400 31.469 70.087
3 800 × 600 37.879 60.317
4 1024 × 768 48.363 60.004
5 1280 × 720 45.000 60.000
6 1366 × 768 60.000 60.000
Preset timing resolutions
A-15 Preset timing resolutions
Table
Preset Timing name Pixel format Horz freq (kHz) Vert freq (Hz)
1 480p 720 × 480 31.469 60
30 Appendix A Technical specications
Page 39
Table A-15 Preset timing resolutions (continued)
Preset Timing name Pixel format Horz freq (kHz) Vert freq (Hz)
2 576p 720 × 576 31.250 50
3 720p50 1280 × 720 37.500 50
4 720p60 1280 × 720 45.000 60
5 1080p60 1920 × 1080 67.500 60
6 1080p50 1920 × 1080 56.250 50
Energy saver feature
The monitor supports a reduced power state. The reduced power state is initiated if the monitor detects the
absence of either the horizontal sync signal or the vertical sync signal. Upon detecting the absence of these
signals, the monitor screen is blank, the backlight is turned o, and the power light turns amber. When the
monitor is in the reduced power state, the monitor uses <0.5 W of power. There is a brief warm-up period
before the monitor returns to its normal operating state.
See the computer manual for instructions on setting the energy saver mode (sometimes called power
management feature).
NOTE: This power saver feature works only when the monitor is connected to a computer that has energy
saver features.
By selecting the settings in the monitor Sleep Timer utility, you can also program the monitor to initiate the
reduced power state at a predetermined time. When the monitor Sleep Timer utility initiates the reduced
power state, the power light blinks amber.
Energy saver feature 31
Page 40
B Accessibility
HP and accessibility
Because HP works to weave diversity, inclusion, and work/life into the fabric of the company, it is reected in
everything HP does. HP strives to create an inclusive environment focused on connecting people to the power
of technology throughout the world.
Finding the technology tools you need
Technology can unleash your human potential. Assistive technology removes barriers and helps you create
independence at home, at work, and in the community. Assistive technology helps increase, maintain, and
improve the functional capabilities of electronic and information technology. For more information, see
Finding the best assistive technology on page 33.
The HP commitment
HP is committed to providing products and services that are accessible for people with disabilities. This
commitment supports the company's diversity objectives and helps ensure that the benets of technology
are available to all.
The HP accessibility goal is to design, produce, and market products and services that can be eectively used
by everyone, including people with disabilities, either on a stand-alone basis or with appropriate assistive
devices.
To achieve that goal, this Accessibility Policy establishes seven key objectives to guide HP actions. All HP
managers and employees are expected to support these objectives and their implementation in accordance
with their roles and responsibilities:
● Raise the level of awareness of accessibility issues within HP, and provide employees with the training
they need to design, produce, market, and deliver accessible products and services.
● Develop accessibility guidelines for products and services, and hold product development groups
accountable for implementing these guidelines where competitively, technically, and economically
feasible.
● Involve people with disabilities in the development of accessibility guidelines and in the design and
testing of products and services.
● Document accessibility features, and make information about HP products and services publicly
available in an accessible form.
● Establish relationships with leading assistive technology and solution providers.
● Support internal and external research and development that improves assistive technology relevant to
HP products and services.
● Support and contribute to industry standards and guidelines for accessibility.
International Association of Accessibility Professionals (IAAP)
IAAP is a not-for-prot association focused on advancing the accessibility profession through networking,
education, and certication. The objective is to help accessibility professionals develop and advance their
careers and to better enable organizations to integrate accessibility into their products and infrastructure.
32 Appendix B Accessibility
Page 41
As a founding member, HP joined to participate with other organizations to advance the eld of accessibility.
This commitment supports HP’s accessibility goal of designing, producing, and marketing products and
services that people with disabilities can eectively use.
IAAP will make the profession strong by globally connecting individuals, students, and organizations to learn
from one another. If you are interested in learning more, go to http://www.accessibilityassociation.org to join
the online community, sign up for newsletters, and learn about membership options.
Finding the best assistive technology
Everyone, including people with disabilities or age-related limitations, should be able to communicate,
express themselves, and connect with the world using technology. HP is committed to increasing accessibility
awareness within HP and with our customers and partners. Whether it’s large fonts that are easy on the eyes,
voice recognition that lets you give your hands a rest, or any other assistive technology to help with your
specic situation—a variety of assistive technologies make HP products easier to use. How do you choose?
Assessing your needs
Technology can unleash your potential. Assistive technology removes barriers and helps you create
independence at home, at work, and in the community. Assistive technology (AT) helps increase, maintain,
and improve the functional capabilities of electronic and information technology.
You can choose from many AT products. Your AT assessment should allow you to evaluate several products,
answer your questions, and facilitate your selection of the best solution for your situation. You will nd that
professionals qualied to do AT assessments come from many elds, including those licensed or certied in
physical therapy, occupational therapy, speech/language pathology, and other areas of expertise. Others,
while not certied or licensed, can also provide evaluation information. You will want to ask about the
individual's experience, expertise, and fees to determine if they are appropriate for your needs.
Accessibility for HP products
The following links provide information about accessibility features and assistive technology, if applicable,
included in various HP products. These resources will help you select the specic assistive technology
features and product(s) most appropriate for your situation.
● HP Elite x3–Accessibility Options (Windows 10 Mobile)
● HP PCs–Windows 7 Accessibility Options
● HP PCs–Windows 8 Accessibility Options
● HP PC’s–Windows 10 Accessibility Options
● HP Slate 7 Tablets–Enabling Accessibility Features on Your HP Tablet (Android 4.1/Jelly Bean)
● HP SlateBook PCs–Enabling Accessibility Features (Android 4.3, 4.2/Jelly Bean)
● HP Chromebook PCs–Enabling Accessibility Features on Your HP Chromebook or Chromebox (Chrome
OS)
● HP Shopping–peripherals for HP products
If you need additional support with the accessibility features on your HP product, see Contacting support
on page 36.
Additional links to external partners and suppliers that may provide additional assistance:
● Microsoft Accessibility information (Windows 7, Windows 8, Windows 10, Microsoft Oice)
● Google Products accessibility information (Android, Chrome, Google Apps)
HP and accessibility 33
Page 42
● Assistive Technologies sorted by impairment type
● Assistive Technology Industry Association (ATIA)
Standards and legislation
Standards
Section 508 of the Federal Acquisition Regulation (FAR) standards was created by the US Access Board to
address access to information and communication technology (ICT) for people with physical, sensory, or
cognitive disabilities. The standards contain technical criteria specic to various types of technologies, as well
as performance-based requirements which focus on functional capabilities of covered products. Specic
criteria cover software applications and operating systems, web-based information and applications,
computers, telecommunications products, video and multimedia, and self-contained closed products.
Mandate 376 – EN 301 549
The EN 301 549 standard was created by the European Union within Mandate 376 as the basis for an online
toolkit for public procurement of ICT products. The standard species the functional accessibility
requirements applicable to ICT products and services, together with a description of the test procedures and
evaluation methodology for each accessibility requirement.
Web Content Accessibility Guidelines (WCAG)
Web Content Accessibility Guidelines (WCAG) from the W3C's Web Accessibility Initiative (WAI) helps web
designers and developers create sites that better meet the needs of people with disabilities or age-related
limitations. WCAG advances accessibility across the full range of web content (text, images, audio, and video)
and web applications. WCAG can be precisely tested, is easy to understand and use, and allows web
developers exibility for innovation. WCAG 2.0 has also been approved as ISO/IEC 40500:2012.
WCAG specically addresses barriers to accessing the web experienced by people with visual, auditory,
physical, cognitive, and neurological disabilities, and by older web users with accessibility needs. WCAG 2.0
provides characteristics of accessible content:
● Perceivable (for instance, by addressing text alternatives for images, captions for audio, adaptability of
presentation, and color contrast)
● Operable (by addressing keyboard access, color contrast, timing of input, seizure avoidance, and
navigability)
● Understandable (by addressing readability, predictability, and input assistance)
● Robust (for instance, by addressing compatibility with assistive technologies)
Legislation and regulations
Accessibility of IT and information has become an area of increasing legislative importance. The following
links provide information about key legislation, regulations, and standards.
● United States
● Canada
● Europe
● Australia
● Worldwide
34 Appendix B Accessibility
Page 43
Useful accessibility resources and links
The following organizations might be good resources for information about disabilities and age-related
limitations.
NOTE: This is not an exhaustive list. These organizations are provided for informational purposes only. HP
assumes no responsibility for information or contacts you encounter on the Internet. Listing on this page
does not imply endorsement by HP.
Organizations
● American Association of People with Disabilities (AAPD)
● The Association of Assistive Technology Act Programs (ATAP)
● Hearing Loss Association of America (HLAA)
● Information Technology Technical Assistance and Training Center (ITTATC)
● Lighthouse International
● National Association of the Deaf
● National Federation of the Blind
● Rehabilitation Engineering & Assistive Technology Society of North America (RESNA)
● Telecommunications for the Deaf and Hard of Hearing, Inc. (TDI)
● W3C Web Accessibility Initiative (WAI)
Educational institutions
● California State University, Northridge, Center on Disabilities (CSUN)
● University of Wisconsin - Madison, Trace Center
● University of Minnesota computer accommodations program
Other disability resources
● ADA (Americans with Disabilities Act) Technical Assistance Program
● ILO Global Business and Disability network
● EnableMart
● European Disability Forum
● Job Accommodation Network
● Microsoft Enable
HP links
Our contact webform
HP comfort and safety guide
HP public sector sales
Useful accessibility resources and links 35
Page 44
Contacting support
NOTE: Support is in English only.
● Customers who are deaf or hard of hearing who have questions about technical support or accessibility
of HP products:
– Use TRS/VRS/WebCapTel to call (877) 656-7058 Monday through Friday, 6 a.m. to 9 p.m. Mountain
Time.
● Customers with other disabilities or age-related limitations who have questions about technical support
or accessibility of HP products, choose one of the following options:
– Call (888) 259-5707 Monday through Friday, 6 a.m. to 9 p.m. Mountain Time.
– Complete the Contact form for people with disabilities or age-related limitations.
36 Appendix B Accessibility
Loading...