HP 2510-24 Installation And Getting Started Manual

Download

Page 1

ProCurve Series 2510-24 Switch

Installation and Getting Started Guide

www.procurve.com

Page 2

Page 3

ProCurve Series 2510 Switch

Installation and Getting Started Guide

Page 4

This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translation into another language without the prior written consent of Hewlett-Packard.

Publication Number

5991-3833 July 2006

Applicable Products

ProCurve Switch 2510-24 (J9019A)

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING , BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

The only warranties for HP products and services are set fo rth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with the product.

A copy of the specific warranty terms applicable to your HewlettPackard products and replacement parts can be obtained from your HP Sales and Service Office or authorized dealer.

Hewlett-Packard Company 8000 Foothills Boulevard, m/s 5552 Roseville, California 95747-5552

http://www.procurve.com

Safety

Before installing and operating these products, please read the “Installation Precautions” in chapter 2, “Installing the Switch”, and the safety statements in appendix B, “Safety and EMC Regulatory Statements”.

Page 5

1 Introducing the Switch

Front of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

LED Mode Select Button and Indicator LEDs . . . . . . . . . . . . . . . . . . . . 1-4

Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Back of the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

2 Installing the Switch

Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2. Installing or Removing mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

3. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

LED Behavior: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

4. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Rack or Cabinet Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Rack Mounting the Switch 2510-24 . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Horizontal Surface Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

5. Connect the Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . . 2-15

6. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Using the RJ-45 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Connecting Cables to mini-GBICs . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

iii

Page 6

7. (Optional) Connect a Console to the Switch . . . . . . . . . . . . . . . . . . 2-17

Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Direct Console Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Sample Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

As a Desktop Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19

As a Segment Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Connecting to a Backbone Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

Stacking the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

3 Configuring the Switch

Recommended Minimal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Using the Console Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Using the IP Address for Remote Switch Management . . . . . . . . . . . 3-5

Starting a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Starting a Web Browser Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

4 Troubleshooting

Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Checking the Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Checking Console Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Testing Twisted-Pair Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Testing Switch-to-Device Network Communications . . . . . . . . . . . . 4-10

Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . 4-10

Restoring the Factory Default Configuration . . . . . . . . . . . . . . . . . . 4-11

Downloading New Switch Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

ProCurve Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Page 7

A Switch Specifications

Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Lasers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

B Switch Ports and Network Cables

Switch Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Twisted-Pair Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Mode Conditioning Patch Cord for Gigabit-LX . . . . . . . . . . . . . . . . . B-3

Installing the Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . B-5

Straight-Through Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . B-6

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

Crossover Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connection . . . . . . . . . . . . . . . . . . . . . B-7

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

C Safety and EMC Regulatory Statements

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Informations concernant la sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Hinweise zur Sicherheit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Considerazioni sulla sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Consideraciones sobre seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

Safety Information (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6

Safety Information (China) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7

Page 8

EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9

Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9

European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10

D Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements D-1

Index

Page 9

Introducing the Switch

The ProCurve Switch 2510-24 is a multiport switch that can be used to build high-performance switched workgroup networks. These switches are storeand-forward devices offering low latency for high-speed networking.

Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps

ProCurve Switch

Link

Mode

2510-24

J9019A

Power

Fault

LED

Locator

Mode

Test

Reset

Console

Act

FDx

Spd

Link

Mode

Clear

864

The Switch 2510-24 has 24 auto-sensing 10/100Base-TX RJ-45 ports, two dualpersonality ports—either auto-sensing 10/100/1000Base-T RJ-45 or miniGBIC.

10/100Base-T Ports (1 - 24)  Ports are HP Auto MDI-X

Link

Mode

Link

Mode

2119

222018

Introducing the Switch

ProCurve Switch 2510-24 (J9019A)

Link

Mode

25T 26T

Link

25M

Dual-Personality Ports:

10/100/1000-T (T)

Mode

or Mini-GBIC (M)

26M

Use only one (T or M)

for each Port

The dual-personality ports have either auto-sensing 10/100/1000Base-T RJ-45, or mini-GBIC connectivity. If any of the mini-GBIC ports are used the corresponding RJ-45 port will be disabled.

These switches are designed to be used primarily as a high-density wiring closet or desktop switch. These switches can directly connect computers, printers, and servers to provide dedicated bandwidth to those devices, and can build a switched network infrastructure by connecting the switch to hubs, other switches, or routers. In addition, the Series 2510 Switch offer full network management capabilities.

This chapter describes the ProCurve Switch 2510-24, including:

■ front and back of the switch

■ LEDs

■ switch features

1-1

Page 10

Introducing the Switch

Front of the Switch

Power, Fault and Locator

Test Status LED

Switch port LEDs

ProCurve Switch 2510-24

LEDs

Link

Mode

Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps

ProCurve Switch

Link

Mode

2510-24

J9019A

Power

Introducing the Switch

Fault

LED

Locator

Mode

Test

Reset

Console

Act

FDx

Spd

Link

Mode

Clear

864

10/100Base-T Ports (1 - 24)  Ports are HP Auto MDI-X

Link

Mode

Link

Mode

2119

222018

LED Mode select button

Console port

and indicator LEDs

10/100Base-TX RJ-

45 ports*

25T 26T

Link

25M

Dual-Personality Ports:

10/100/1000-T (T)

Mode

or Mini-GBIC (M)

26M

Use only one (T or M)

for each Port

Dual-personality ports

(10/100/1000Base-T* or

mini-GBIC)

Reset and Clear

buttons

* 10/100/1000Base-T ports have the IEEE Auto MDI/MDI-X feature.

Network Ports

■ 24 auto-sensing 10/100Base-TX ports.

All these ports have the “IEEE Auto MDI/MDI-X” feature, which means you can use either straight-through or crossover twisted-pair cables to connect any network devices to the switch.

■ Two dual-personality ports. Use either the 10/100/1000Base-T RJ-45

connector, or install a supported ProCurve mini-GBIC for fiber-optic connections. The RJ-45 connectors support the IEEE Auto MDI/MDI-X feature, which means you can use either straight-through or crossover twisted-pair cables to connect any network device to the switch.

1-2

Dual-Personality Port Operation. By default, the RJ-45 connectors are enabled. If a mini-GBIC is installed in a slot, it is enabled and the associated RJ-45 connector is disabled and cannot be used. If the mini-GBIC is removed, the associated RJ-45 port is automatically re-enabled.

Console Port

This port is used to connect a console to the Series 2510 Switch by using the supplied cable with the switch. The console port is located on the front of the Switch. This connection is described under “Connect a Console to the Switch” in chapter 2, “Installing the Switch.” The console can be a PC or workstation running a VT-100 terminal emulator, or a VT-100 terminal.

Page 11

Introducing the Switch

Front of the Switch

LEDs

Table 1-1. Switch LEDs

Switch LEDs State Meaning

Power (green)

Fault (orange)

Locator (Blue)

Te st (green)

On Off

Off The normal state; indicates there are no fault conditions on the switch.

Blinking* A fault has occurred on one of the switch ports. The Status LED for the component with

On On briefly after the switch is powered on or reset, at the beginning of switch self test.

Blinking Off

Off The normal operational state; the switch is not undergoing self test.

On The switch self test and initialization are in progress after the switch has been power

Blinking* A component of the switch has failed its self test. The status LED for that component,

The switch is receiving power. The switch is NOT receiving power.

the fault will blink simultaneously. If just the Fault LED is blinking, the switch could be attached to an RPS but not receiving power.

If this LED is on for a prolonged time, the switch has encountered a fatal hardware failure, or has failed its self test. See chapter 4, “Troubleshooting” for more information.

Locate function is active. Software controlled, can be set to on or blinking. Locate function is disabled.

cycled or reset . The switch is not operational until this LED goes off. The test LED also comes on briefly when you “hot swap” a mini-GBIC into the switch; the mini-GBIC is self tested when it is hot swapped.

for example an RJ-45 port, and the switch Fault LED will blink simultaneously.

Introducing the Switch

Port LEDs (green – Link

and Mode)

Link Indicates the port LEDs are displaying link information:

• if the port LED is on, the port is enabled and receiving a link indication from the connected device.

• if the port LED is off, the port has no active network cable connected, or is not receiving link beat or sufficient light. Otherwise, the port may have been disabled through the switch console, the web browser interface, or ProCurve Manager.

if the port LED is blinking* simultaneously with the Fault LED, the corresponding port has failed its self test.

Mode The operation of the Mode LED is controlled by the LED Mode select button, and the

current setting is indicated by the LED Mode indicator LEDs near the button. Press the button to step from one view mode to the next. The default view is Activity (Act).

1-3

Page 12

Introducing the Switch

Front of the Switch

Switch LEDs State Meaning

LED Mode View (3 green LEDs)

Act Indicates the port LEDs are displaying network activity information.

FDx Indicates port LEDs are lit for ports in Full Duplex Mode. Off indicates half duplex.

Spd Indicates port Mode LEDs are displaying the connection speed of each port.

• if the port LED is off, the port is operating at 10 Mbps.

• if the port LED is blinking **, the port is operating at 100 Mbps.

• if the port LED is on continously, the port is operating at 1000 Mbps.

Introducing the Switch

* The blinking behavior is an on/off cycle once every 1.6 seconds, approximately. ** The blinking behavior is an on/off cycle once every 0.8 seconds, approximately.

LED Mode Select Button and Indicator LEDs

To optimize the amount of information displayed for each of the switch ports without overwhelming you with LEDs, the Series 2510 Switch uses two LEDs for each port. The operation of these LEDs is controlled by the LED Mode select button, and the current setting is indicated by the LED Mode indicator LEDs near the button. Press the button to step from one view mode to the next.

ProCurve Switch 2510-24

10/100Base-T Ports (1 - 24)  Ports are HP Auto MDI-X

Link

Mode

Link

Mode

2018

Power

Fault

Locator

Console

ProCurve Switch

2510-24

J9019A

LED

Mode

Test

Reset

Port LEDs

(two for each port)

Link and Mode

Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps

Link

Mode

Act

FDx

Spd

Link

Mode

Clear

864

1-4

LED Mode select button

and indicator LEDs

■ Each port has a Link LED. If it is lit, the port has a link. If the Link LED is

blinking, the port has failed its self test. The Fault and Test LEDs will be blinking simultaneously.

■ If the Activity (Act) indicator LED is lit, each port LED displays activity

information for the associated port—it flickers as network traffic is received and transmitted through the port.

Page 13

Introducing the Switch

Front of the Switch

■ If the Full Duplex (FDx) indicator LED is lit, the port LEDs light for those

ports that are operating in full duplex.

■ If the Speed (Spd) indicator LED is lit, the port LEDs behave as follows

to indicate the connection speed for the port:

• Off = 10 Mbps

• Blinking = 100 Mbps (the flashing behavior is a repeated on/off cycle once every 0.5 sec.)

• On = 1000 Mbps

Reset Button

This button is used to reset the switch while it is powered on. This action clears any temporary error conditions that may have occurred and executes the switch self test.

Clear Button

This button is used for these purposes:

■ Deleting Passwords - When pressed by itself for at least one second, the

button deletes any switch console access passwords that you may have configured. Use this feature if you have misplaced the password and need console access.

Introducing the Switch

This button is provided for your convenience, but its presence means that if you are concerned with the security of the switch configuration and operation, you should make sure the switch is installed in a secure location, such as a locked wiring closet.

■ Restoring Factory Default Configuration - When pressed with the

Reset button in a specific pattern, any configuration changes you may have made through the switch console, the web browser interface, and SNMP management are removed, and the factory default configuration is restored to the switch. For the specific method to restore the factory default configuration, see “Restoring the Factory Default Configuration”

on page 11 in chapter 4, “Troubleshooting” of this manual.

1-5

Page 14

Introducing the Switch

Back of the Switch

ProCurve Switch 2510-24 (J9019A)

Introducing the Switch

AC power connector

Power Connector

The Series 2510 Switch does not have a power switch; it is powered on when connected to an active AC power source. This switch automatically adjusts to any voltage between 100-240 volts and either 50 or 60 Hz. No voltage range settings are required.

1-6

Page 15

Introducing the Switch

Switch Features

The features of the Series 2510 Switch include:

■ 24 auto-sensing 10/100Base-TX RJ-45 ports.

■ two dual-personality ports—either the auto sensing 10/100/1000Base-T

RJ-45 or the mini-GBIC can be used for each port.

■ plug-and-play networking—all ports are enabled—just connect the

network cables to active network devices and your switched network is operational.

■ IEEE 802.3ab Auto MDI /MDI-X on all 10/100 twisted-pair ports, meaning

that all connections can be made using straight-through twistedpair cables. Cross-over cables are not required, although they will also

work. The pin operation of each port is automatically adjusted for the attached device: if the switch detects that another switch or hub is connected to the port, it configures the port as MDI; if the switch detects that an end-node device is connected to the port, it configures the port as MDI-X.

■ automatic learning of the network addresses in each switch’s 8000-

address forwarding table, (with configurable address aging value).

■ automatically negotiated full-duplex operation for all 10/100Base-TX RJ-

45 ports when connected to other auto-negotiating devices—the miniGBIC ports always operate at full duplex.

■ easy management of the switch through several available interfaces:

• console interface—a full featured, easy to use, VT-100 terminal interface that is especially good for out-of-band switch management or for Telnet access to the switch.

• web browser interface—an easy to use built-in graphical interface that can be accessed from common web browsers.

• ProCurve Manager—an SNMP based, graphical network managent tool you can use to manage your entire network. this product is included with your new switch.

■ support for the Spanning Tree Protocol to eliminate network loops.

■ support for up to 64 IEEE 802.1Q-compliant VLANs so you can divide

the attached end nodes into logical groupings that fit your business needs.

■ support for many advanced features to enhance network performance—

for a description, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

■ download of new switch software for product enhancements or bug fixes.

Introducing the Switch

1-7

Page 16

Page 17

Installing the Switch

The ProCurve Series 2510 Switch is easy to install. It comes with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, in an equipment cabinet, on a wall, and with rubber feet that can be attached so the switch can be securely located on a horizontal surface. The brackets are designed to allow mounting the switch in a variety of locations and orientations. This chapter shows how to install the switch.

Included Parts

The Series 2510 Switch has the following components shipped with it:

■ ProCurve Series 2510 Switch Installation and Getting Started Guide

(5991-3833), this manual

■ Read Me First

■ Console cable (5188-3836)

■ Customer Support/Warranty booklet

■ Accessory kit

Installing the Switch

5064-2085

two mounting brackets

four 8-mm M4 screws to attach the mounting brackets to the switch

four 5/8-inch number 12-24 screws to attach the switch to a rack

four rubber feet

2-1

Page 18

Installing the Switch

Included Parts

■ Power cord, one of the following:

Installing the Switch

Japan Power Cord Warning

Australia/New Zealand China Continental Europe Denmark Japan Switzerland United Kingdom/Hong Kong/Singapore United States/Canada/Mexico South Africa Israel Thailand Taiwan

8120-6803 8120-8377 8120-6802 8120-6806 8120-6804 8120-6807 8120-8709 8120-6805 8120-8929 8121-1009 8121-0673 8121-0964

2-2

Page 19

Installing the Switch

Installation Procedures

Summary

Follow these steps to install the switch. The rest of this chapter provides details on these steps.

1. Prepare the installation site (page 2-5). Ensure the physical environment is properly prepared, including having the correct network cabling ready to connect to the switch and having an appropriate location for the switch. Please see page 2-4 for some installation precautions.

2. Install mini-GBICs (optional—page 2-7). The switch has two slots for installing mini-GBICs. Depending on where you will install the switch, it may be easier to install the mini-GBICs first. Mini-GBICs can be hot swapped—they can be installed or removed while the switch is powered on.

3. Verify the switch passes self test (page 2-9). Plug the switch into a power source and observe the LEDs on the switch’s front panel that they indicate correct switch operation.

Installing the Switch

4. Mount the switch (page 2-11). The Series 2510 Switch can be mounted in a 19-inch telco rack, in an equipment cabinet, on a wall, or on a horizontal surface.

5. Connect power to the switch (page 2-15). Once the switch is mounted, plug it into the nearby main power source.

6. Connect the network cables (page 2-16). Using the appropriate network cables, connect the network devices to the switch ports.

7. Connect a console to the switch (optional—page 2-17). You may wish to modify the switch’s configuration, for example, to configure an IP address so it can be managed using a web browser, from an SNMP network management station, or through a Telnet session. Configuration changes can be made easily by using the included console cable to connect a PC to the switch’s console port.

At this point, the switch is fully installed. See the rest of this chapter if you need more detailed information on any of these installation steps.

2-3

Page 20

Installing the Switch

Installation Procedures

Installation Precautions:

Follow these precautions when installing the Series 2510 Switch.

WARNING ■ The rack or cabinet should be adequately secured to prevent it

from becoming unstable and/or falling over.

Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at the bottom and progressively lighter devices installed above.

■ For safe operation, do not install the switch with the with the vents

facing either downward.

■ Left side vents cannot be placed downward. (That is, the left side

of the unit while facing the front.)

Cautions ■ Ensure the power source circuits are properly grounded, then use the

power cord supplied with the switch to connect it to the power source.

■ If your installation requires a different power cord than the one supplied

with the switch, be sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the switch.

2-4

■ When installing the switch, the AC outlet should be near the switch and

should be easily accessible in case the switch must be powered off.

■ Ensure the switch does not overload the power circuits, wiring, and over-

current protection. To determine the possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the same circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere ratings are usually printed on the devices near the AC power connectors.

■ Do not install the switch in an environment where the operating ambient

temperature might exceed 45°C (113°F).

■ Ensure the air flow around the sides and back of the switch is not

restricted.

Page 21

1. Prepare the Installation Site

■ Cabling Infrastructure - Ensure the cabling infrastructure meets the

necessary network specifications. See the following table for cable types and lengths, and see appendix B, “Cables and Connectors” for more information:

Table 2-1. Summary of Cable Types to Use With the Switch

Port Type Cable Type Length Limits

Twisted-Pair Cables

Installing the Switch

Installation Procedures

10/100/1000Base-T For either 10, 100 Mbps, or 1000 Mbps

operation:

Category 5 or better, 100-ohm UTP or shielded twisted-pair (STP) balanced cable. For 1000 Mbps (gigabit) operation, Category 5E cabling or better is recommended.

100 meters

Note: The Series 2510 Switch is compatible with the IEEE 802.3ab standard including the “Auto MDI/MDI-X” feature, which allows use of either straight-through or crossover twisted-pair cables for connecting to any network devices including end nodes, such as computers, or to other switches, hubs, and routers.

Note: For 1000 Mbps operation, all four wire pairs are used for data transmission.

Installing the Switch

2-5

Page 22

Installing the Switch

Installation Procedures

Port Type Cable Type Length Limits

Fiber Optic Cables

Installing the Switch

Gigabit-SX (on Gigabit-SX-LC mini-GBIC)

Gigabit-LX (on Gigabit-LX-LC mini-GBIC)

Gigabit-LH (on Gigabit-LH-LC mini-GBIC)

Multimode fiber-optic cables designed for Gigabit Ethernet: 62.5/125 μm or 50/125 μm (core/cladding) diameter, low metal content, graded-index cables, fitted with LC connectors. The cables must comply with the ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a standards.

Single-mode fiber-optic cables designed for Gigabit Ethernet: 9/125 μm (core/cladding) diameter, 1310 nm, low metal content cables, fitted with LC connectors. The cables must comply with the ITU-T G.652 and ISO/IEC 793-2 Type B1 standards.

The multimode cables specified for the GigabitSX mini-GBIC may also be used, but a modeconditioning patch cord may be needed — see

“Mode Conditioning Patch Cord for Gigabit-LX” on page B-3 for more information.

Single-mode fiber-optic cables designed for Gigabit Ethernet and fitted with LC connectors.

■ Installation Location - Before installing the switch, plan its location and

• 62.5 μm cable: – 160 MHz*km = 220 meters – 200 MHz*km = 275 meters

•50 μm cable: – 400 MHz*km = 500 meters – 500 MHz*km = 550 meters

• single-mode cable = 5 kilometers

• multimode cable = 550 meters

• single-mode cable = 70 kilometers

orientation relative to other devices and equipment:

• In the front of the switch, leave at least 7.6 cm (3 inches) of space for the twisted-pair and fiber-optic cabling.

• In the back of the switch, leave at least 3.8 cm (1 1/2 inches) of space for the power cord.

• On the sides of the switch, leave at least 7.6 cm (3 inches) for cooling, except if the switch is installed in an open EIA/TIA rack.

2-6

Page 23

Installing the Switch

Installation Procedures

2. Installing or Removing mini-GBICs

You can install or remove a mini-GBIC from a mini-GBIC slot without having to power off the switch. Use only ProCurve mini-GBICs.

Notes ■ The mini-GBIC slots are shared with the two 10/100/1000Base-T RJ-45

ports. If a mini-GBIC is installed in a slot, the associated RJ-45 port is disabled and cannot be used.

■ The mini-GBIC ports operate only at full duplex. Half duplex operation is

not supported.

■ Ensure the network cable is NOT connected when you install or remove

a mini-GBIC.

When this manual was printed, the supported mini-GBICs include the following:

■ ProCurve Gigabit-SX-LC mini-GBIC (J4858B)

■ ProCurve Gigabit-LX-LC mini-GBIC (J4859B)

■ ProCurve Gigabit-LH-LC mini-GBIC (J4860B)

Caution Use only supported genuine ProCurve mini-GBICs with your switch. Non-

ProCurve mini-GBICs are not supported, and their use may result in product malfunction. Should you require additional ProCurve mini-GBICs, contact your ProCurve Networking Sales and Service Office or authorized dealer.

Installing the Switch

Installing the mini-GBICs:

Hold the mini-GBIC by its sides and gently insert it into either of the slots on the switch until the mini-GBIC clicks into place.When the mini-GBIC is installed, the Link LED turns on for 2 seconds to verify correct installation.

WARNING The ProCurve mini-GBICs are Class 1 laser devices. Avoid direct eye

exposure to the beam coming from the transmit port.

2-7

Page 24

Installing the Switch

Installation Procedures

Removing the mini-GBICs

Note The network cable should be disconnected from the mini-GBIC before

removing it from the switch.

Depending on when you purchased your ProCurve mini-GBIC, it may have either of three different release mechanisms: a plastic tab on the bottom of the mini-GBIC, a plastic collar around the mini-GBIC, or a wire bail.

To remove the mini-GBICs that have the plastic tab or plastic collar, push the tab or collar toward the switch until you see the mini-GBIC release from the switch (you can see it move outward slightly), and then pull it from the slot.

To remove the mini-GBICs that have the wire bail, lower the bail until it is approximately horizontal, and then using the bail, pull the mini-GBIC from the slot.

2-8

Page 25

Installing the Switch

Installation Procedures

3. Verify the Switch Passes Self Test

Before mounting the switch in its network location, you should first verify it is working properly by plugging it into a power source and verifying it passes self test.

1. Connect the power cord supplied with the switch to the power connector on the back of the switch, and then into a properly grounded electrical outlet.

Connect power cord to

the power connector

Note The Series 2510 Switch does not have a power switch. It is powered on when

the power cord is connected to the switch and to a power source. For safety, the power outlet should be located near the switch installation.

Installing the Switch

The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz. No voltage range settings are required.

If your installation requires a different power cord than the one supplied with the switch, be sure to use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the switch.

2-9

Page 26

Installing the Switch

Installation Procedures

2. Check the LEDs on the switch as described below.

Installing the Switch

ProCurve Switch

2510-24

J9019A

Power

Fault

Locator

Test

Console

Power, Fault

and locator

Switch port LEDs

Spd mode: off = 10 Mbps, flash = 100 Mbps, on = 1000 Mbps

Link

Mode

Act

LED

Mode

FDx

Spd

Link

Mode

Reset

Clear

Tes t LED

864

ProCurve Switch 2510-24 (J9019A)

10/100Base-T Ports (1 - 24)  Ports are HP Auto MDI-X

Link

Mode

Link

Mode

2119

222018

LEDs

When the switch is powered on, it performs its diagnostic self test. Self test takes approximately 50 seconds to complete.

LED Behavior:

During the self test:

• Initially, all the status, LED Mode and port LEDs are on for most of

the duration of the test.

• Most of the LEDs go off and then may come on again during phases

of the self test. For the duration of the self test, the Test LED stays on.

Link

2-10

When the self test completes successfully:

•The Power LED remains on.

•The Fault and Test LEDs go off.

• The port LEDs on the front of the switch go into their normal opera-

tional mode: – If the ports are connected to active network devices, the LEDs

behave according to the LED Mode selected. In the default view mode (Link), the LEDs should be on.

– If the ports are not connected to active network devices, the LEDs

will stay off.

If the LED display is different than what is described above, especially if the Fault and Test LEDs stay on for more than 60 seconds or they start blinking, the self test has not completed correctly. Refer to chapter 4, “Troubleshooting” for diagnostic help.

Page 27

Installing the Switch

Installation Procedures

4. Mount the Switch

After the switch passes self test, you are ready to mount the switch in a stable location. The Series 2510 Switch can be mounted in these ways:

■ in a rack or cabinet

■ on the wall

■ on a horizontal surface

Rack or Cabinet Mounting

The Series 2510 Switch is designed to be mounted in any EIA-standard 19-inch telco rack or communication equipment cabinet.

WARNING For safe operation, please read the mounting precautions on

page 2-4, before mounting a switch.

Installing the Switch

Equipment Cabinet Note

The 12-24 screws supplied with the switch are the correct threading for standard EIA/TIA open 19-inch racks. If you are installing the switch in an equipment cabinet such as a server cabinet, use the clips and screws that came with the cabinet in place of the 12-24 screws that are supplied with the switch.

Complete step 1, and plan which four holes you will be using in the cabinet and install all four clips. Then proceed to step 2.

2-11

Page 28

Installing the Switch

Installation Procedures

Rack Mounting the Switch 2510-24

1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws.

8 mm

M4 screws

Note The mounting brackets have multiple mounting holes and can be rotated

allowing for a wide variety of mounting options. These include mounting the switch so its front face is flush with the face of the rack, or mounting it in a more balanced position as shown in the illustration.

Note Steps 2, 3, and 4 on the next page describe a convenient method of mounting

the switch in a rack by placing it on two screws that you first install in the rack. You may, instead, just hold the switch with attached brackets up to the rack and move it vertically until rack holes line up with the bracket holes and notches, then insert and tighten the four screws holding the brackets to the rack.

WARNING For safe reliable installation, only use the screws provided in the

accessory kit to attach the mounting brackets to the switch.

2-12

Page 29

Installing the Switch

Installation Procedures

2. Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Ensure that the screws are at the same level in each upright.

Partially install a screw

into the top hole of a

close (0.5-inch) pair on

both sides of the rack

3. Place the switch in the rack and lower it so the notches in the bottom of the bracket slide onto the screws, then tighten these screws.

Installing the Switch

Lower switch with mounting

brackets onto the partially

installed screw

2-13

Page 30

Installing the Switch

Installation Procedures

4. Install the other number 12-24 screw into the upper hole in each bracket. Tighten these screws.

Install additional

screw

Horizontal Surface Mounting

Installing the Switch

Place the switch on a table or other horizontal surface. The switch comes with rubber feet in the accessory kit that can be used to help keep the switch from sliding on the surface.

Attach the rubber feet to the four corners on the bottom of the switch within the embossed angled lines. Use a sturdy surface in an uncluttered area. You may want to secure the networking cables and switch power cord to the table leg or other part of the surface structure to help prevent tripping over the cords.

Caution Make sure the air flow is not restricted around the sides and back of the switch.

2-14

Page 31

Installing the Switch

Installation Procedures

Wall Mounting

Caution The switch can only be mounted with the RJ-45 ports facing up.

1. Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws.

2. Attach the switch to the wall or wood surface with two 5/8-inch number 12 wood screws (not included).

Wall

M4 screws

RJ-45 Ports

5/8-inch

wood screws

5. Connect the Switch to a Power Source

1. Plug the included power cord into the switch’s power connector and into a nearby AC power source.

2. Re-check the LEDs during self test. See “LED Behavior” on page 2-10

Installing the Switch

2-15

Page 32

Installing the Switch

Installation Procedures

6. Connect the Network Cables

Connect the network cables, described under “Cabling Infrastructure” (page

2-5), from the network devices or your patch panels to the fixed RJ-45 ports

on the switch or to any mini-GBICs you have installed in the switch.

Using the RJ-45 Connectors

To connect:

Push the RJ-45 plug into the RJ-45 jack until the tab on the plug clicks into place. When power is on for the switch and for the connected device, the Link LED for the port should light to confirm a powered-on device (for example, an end node) is at the other end of the cable.

If the Link LED does not go on when the network cable is connected to the port, see “Diagnosing with the LEDs” on

page 4-4, in chapter 4, “Trouble-

shooting”.

To disconnect:

Press the small tab on the plug and pull the plug out of the jack.

Spd mode: off = 10Mbps, flash= 100Mbps, on= 1000Mbps

ProCurve Switch

Link

Mode

tor

Console

2510-24

J9019A

Test

Act

LED

Mode

FDx

Spd

Link

Mode

ClearReset

8642

RJ-45 connector

Unshielded twisted-pair cable:

• Category 3, 4, or 5 for 10 Mbps ports

• Category 5 or better for 100 Mbps ports

• Category 5e or better for 1000 Mbps ports Maximum distance: 100 meters

10/100

Link

119

Link

1210

Connecting Cables to mini-GBICs

Note Each of the two mini-GBIC slots is shared with the associated 10/100/

1000Base-T RJ-45 port. If a mini-GBIC is installed in a slot, the associated RJ45 port is disabled.

If you have any mini-GBICs installed in the switch, the type of network connections you will need to use depends on the type of mini-GBICs you have installed. See the table on page 2-6, and appendix B, “Switch Ports and

Network Cables”, for the mini-GBIC cabling information.

2-16

For mini-GBICs ports, and in general for all the switch ports, when a network cable from an active network device is connected to the port, the port LED for that port should go on. If the port LED does not go on when the network cable is connected to the port, see “Diagnosing with the LEDs” on page 4-4 in chapter 4, “Troubleshooting”.

Page 33

Installing the Switch

Installation Procedures

7. (Optional) Connect a Console to the Switch

The switch has a full-featured, easy to use console interface for performing switch management tasks including the following:

■ Monitor switch and port status and observe network activity statistics

■ Modify the switch’s configuration to optimize switch performance,

enhance network traffic control, and improve network security

■ Read the event log and access diagnostic tools to help in troubleshooting

■ Download new software to the switch

■ Add passwords to control access to the switch from the console, web

browser interface, and network management stations

The console can be accessed through these methods:

■ Out-of-band: The switch comes with a serial cable for connecting a PC

or VT-100 terminal, to be used as a console, directly to the switch.The console cable is a DB-9 to RJ45 connector.

■ In-Band: Access the console using Telnet from a PC or UNIX station on

the network, and a VT-100 terminal emulator. This method requires that you first configure the switch with an IP address and subnet mask by using either out-of-band console access or through DHCP/Bootp. For more information on IP addressing and on starting a Telnet session, see chapter 3, “Configuring the Switch”, and the Management and Con- figuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Installing the Switch

The Switch can simultaneously support one out-of-band console session through the Console Port and one in-band Telnet console session.

Terminal Configuration

To connect a console to the switch, configure the PC terminal emulator as a DEC VT-100 (ANSI) terminal or use a VT-100 terminal, and configure either one to operate with these settings:

• any baud rate from 1200 to 115200 (the switch senses the speed)

• 8 data bits, 1 stop bit, no parity, and flow control set to Xon/Xoff

• For the Windows Terminal program, also disable (uncheck) the “Use

Function, Arrow, and C

• For the Hilgraeve HyperTerminal program, select the “Terminal keys”

option for the “Function, arrow, and ctrl keys act as” parameter.

trl Keys for Windows” option

2-17

Page 34

Installing the Switch

Installation Procedures

If you want to operate the console using a different configuration, make sure you change the settings on both the terminal and on the switch so they are compatible. Change the switch settings first, save your changes, then change the terminal settings, then reboot the switch and reestablish the console session.

Direct Console Access

To connect a console to the switch, follow these steps:

Installing the Switch

1. Connect the PC or terminal to the switch’s

Console port

Console Port using the console cable included with the Switch. (If your PC or terminal has a 25-pin serial connector, first

Console cable supplied

with the switch

attach a 9-pin to 25-pin straight-through adapter at one end of the console cable.)

2. Turn on the terminal or

PC running a terminal

emulator program, or

a VT-100 terminal

PC’s power and, if using a PC, start the PC terminal program.

3. Press

[Enter] two or three

This illustration demonstrates the Switch 2510-24.

times and you will see the copyright page and the message “Press any key to continue”. Press a key, and you will then see the switch console command (CLI) prompt, for example:

ProCurve Switch 2510-24#

If you want to continue with console management of the switch at this time, see chapter 3, “Configuring the Switch” for some basic configuration steps. For more detailed information, refer to the Management and Configuration

Guide, which is available on the ProCurve Networking Web site,

www.procurve.com.

2-18

Page 35

Installing the Switch

Sample Network Topologies

This section shows a few sample network topologies in which the Switch is implemented. For more topology information, see the ProCurve networking products Web site,

As a Desktop Switch

www.procurve.com.

Server

ProCurve Switch 2510-24

Link

25T 26T

Power

Fault

Locator

Console

ProCurveSwitch

2510-24

J9019A

Act

LED Mode

FDx

Test

Spd

ClearReset

Spdmode: off=10Mbps, flash=100Mbps, on=1000Mbps

Link

Mode

Link

Mode

10/100Base-TPorts (1 - 24) — Ports are HP Auto MDI-X

Link

Mode

119753

Link

Mode

1210

8642

Mode

232119171513

Dual-PersonalityPorts: 10/100/1000-T (T)

Link

orMini-GBIC(M)

Mode

Useonlyone(T or M)

foreachPort

2220181614

PCs, local servers and

peripherals

LEGEND: GigabitEthernetcableF ast E thernet cable

The Switch is designed to be used primarily as a desktop switch to which end nodes, printers and other peripherals, and servers are directly connected, as shown in the above illustration. Notice that the end node devices are connected to the switch by straight-through or crossover twisted-pair cables. Either cable type can be used because of the “IEEE Auto MDI/MDI-X” features on the Switch.

Installing the Switch

2-19

Page 36

Installing the Switch

Sample Network Topologies

As a Segment Switch

Servers with Gigabit

Ethernet NIC

HP ProCurve Switch 2824

Power

Fault

To backbone

Installing the Switch

Fast Ethernet Switch

hp procurve switch 2650 J4899A

Act

Power

FDx Max

Fault

PCs, local servers, and peripherals

LEGEND: Gigabit Ethernet cable Fiber cableFast Ethernet cable

The Switch also works well as a segment switch. That is, with its high performance, it can be used for interconnecting network segments—simply connect the network hubs that form those segments to the switch, or you can also connect other switches.

In the illustration above, two “Fast” Ethernet hubs with PCs, printers, and local servers attached, are both connected to a Switch. The devices attached to the two hubs can now communicate with each other through the switch. They can also all communicate with the server that is connected to a Gigabit mini-GBIC port on the switch.

Fast Ethernet Switch

hp procurve switch 2650 J4899A

Act

Power

FDx Max

Fault

PCs, local servers, and peripherals

Server with Gigabit Ethernet NIC

2-20

Page 37

Installing the Switch

Sample Network Topologies

Because the Switch has the “IEEE Auto MDI/MDI-X” features, the connections between the switch and the hubs, and between the switch and end nodes or servers can be through category 5 straight-through or crossover twisted-pair cable. Category 3 or 4 cable can also be used if the connection is 10 Mbps only. In all cases, the device ports must be configured to auto negotiate the link characteristics for this feature to work.

The switch, in turn, can be connected to a network backbone through fiberoptic cabling connected to a Gigabit-SX, -LX, or -LH mini-GBIC installed in the switch. Now, all the devices on these network segments can access other network resources that are connected elsewhere on the network backbone.

Installing the Switch

2-21

Page 38

Installing the Switch

Sample Network Topologies

Connecting to a Backbone Switch

Installing the Switch

procurvehp

switch 5304xl J4850A

Console

Power

Fault

1234

Link

1 2 3 4

Mode

J4878A

Link Mode

J4821A

HP ProCurve Switch 5304xl

Server with Gigabit

Ethernet NIC

Fast Ethernet Switch

hpprocurve switch2650 J4899A

Act

Power

FDx Max

Fault

To IT or Data Center

Status

1 2 B C D E F GA H

Reset Clear

Self

Power ModulesFan

Test

100/1000Bas e-T Po rts

22334

Power

Fault

HP ProCurve Switch 5304xl

Server with Gigabit

Ethernet NIC

Fast Ethernet Switch

Power

Fault

ActFDx !Ma x

LED Mode Select

module

J4878A

C D

module

J4878A

Power

procurvehp

switch5304xl

Fault

Reset Clear

J4850A

Console

1234 Link

1 2 3 4

Mode

J4878A

100/1000Base-T Port s

LinkMode

22334

J4821A

hpprocurve switch2650 J4899A

Act FDx Max

Usexl modules on ly

1234 Link

1 2 3 4

Mode

1234

Link

1 2 3 4

Mode

To IT or Data Center

Status

ActFDx !Max

1 2 B C D E F GA H

Self

LEDMode Select

Power ModulesFan

Test

Usexlmodules only

1234 Link

1 2 3 4

Mode

module

J4878A

C D

1234 Link

1 2 3 4

Mode

module

J4878A

Power

Fault

PCs, local servers, and peripherals

module

Power

Fault

module

Server with Gigabit

Ethernet NIC

HP ProCurve Switch 2824

Gigabit link (use fiber if over 100 meters)

PCs, local servers, and peripherals

Server with Gigabit

Ethernet NIC

HP ProCurve Switch 2848

module

Power

Fault

module

Gigabit link (use fiber if over 100 met ers)

HP ProCurve Switch 2848

Fast Ethernet Switch

hpprocurve switch265 0

J4899A

Act

Power

FDx Max

Fault

Fast Ethernet Switch

hpprocurve switch2650 J4899A

Act

Power

FDx Max

Fault

HP ProCurve Switch 2824

Server with Gigabit Ethernet NIC

PCs, local servers, and peripherals

LEGEND: Gigabit Ethernet cable Fiber cableFast Ethernet cable

The simpler desktop and segment networks shown in the previous two examples can easily be combined and expanded. For example, you could use a ProCurve Switch 5304xl to interconnect each of your smaller switched workgroups to form a larger switched network. All the devices in this network can communicate with each other. With a Gigabit-SX Module, for example, in the Switch 5304xl, the entire switched topology could be connected to a campus backbone, as shown in the illustration above.

2-22

PCs, local servers,

and peripherals

Server with Gigabit Ethernet NIC

Page 39

Installing the Switch

Sample Network Topologies

Note In the Backbone Switch illustration, the 1000 Mbps fiber-optic connection

between the Switch 2510-24 and the Switch 5304xl is by way of a Gigabit-SX mini-GBIC installed in the Switch 2510-24 and connected to a Gigabit-SX Module in the Switch 5304xl.

Stacking the Switch

The Series 2510 Switches can be connected together, through standard network connections, and managed through a single IP address. Up to 16 switches can be connected together in such a “virtual stack”.

You identify the switch as the “Commander” and give that switch an IP address. Up to 15 other switches in the network can then easily be configured as Members of the stack and managed through the Commander’s IP address. The management includes Telnet access and web browser interface access to the Commander and to each Member switch through the Commander.

For more information on stacking Switches, please see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

ProCurve Switch 2510-24

To Gigabit-Ethernet

Backbone

HP ProCurve Switch 2848

HP ProCurve Switch 2824

To Gigabit-Ethernet

Power

Fault

Power

Fault

Power

Fault

Power

Fault

LEGEND: Gigabit Ethernet cable

Installing the Switch

Use fiber if over 100 meters

Backbone

(Use fiber if over 100 meters)

2-23

Page 40

Page 41

Configuring the Switch

This chapter is a guide for using the console Switch Setup screen to quickly assign an IP (Internet Protocol) address and subnet mask to the switch, set a Manager password, and, optionally, configure other basic features.

For more information on using the switch console and the other switch management interfaces: the web browser interface, please see the Manage- ment and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Recommended Minimal Configuration

In the factory default configuration, the switch has no IP (Internet Protocol) address and subnet mask, and no passwords. In this state, it can be managed only through a direct console connection. To manage the switch through inband (networked) access, you should configure the switch with an IP address and subnet mask compatible with your network. Also, you should configure a Manager password to control access privileges from the console and web browser interface. Other parameters in the Switch Setup screen can be left at their default settings or you can configure them with values you enter.

Configuring the Switch

Many other features can be configured through the switch’s console interface, to optimize the switch’s performance, to enhance your control of the network traffic, and to improve network security. Once an IP address has been configured on the switch, these features can be accessed more conveniently through a remote Telnet session, through the switch’s web browser interface, and from an SNMP network management station running a network management program. For a listing of switch features available with and without an IP address, refer to “How IP Addressing Affects Switch Operation” in the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

For more information on IP addressing, refer to “IP Configuration” in the Management and Configuration Guide.

3-1

Page 42

Configuring the Switch

Note By default, the switch is configured to acquire an IP address configuration

from a DHCP or Bootp server. To use DHCP/Bootp instead of the manual method described in this chapter, see “DHCP/Bootp Operation” in the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Using the Console Setup Screen

The quickest and easiest way to minimally configure the switch for management and password protection in your network is to use a direct console connection to the switch, start a console session, and access the Switch Setup screen.

1. Using the method described in the preceding section, connect a terminal device to the switch and display the switch console command (CLI) prompt (the default display).

The CLI prompt appears displaying the switch model number, for example:

ProCurve Switch 2510-24#

2. At the prompt, enter the setup command to display the Switch Setup screen. The following illustration shows the Setup screen with the default settings.

Configuring the Switch

3-2

ProCurve Switch 2510-24

3. Use the

[Tab] key to select the Manager Password field and enter a manager

password of up to 16 characters.

2006

Page 43

4. [Tab] to the IP Config (DHCP/Bootp) field and use the Space bar to select the Manual option.

[Tab] to the IP Address field and enter the IP address that is compatible with

your network.

[Tab] to the Subnet Mask field and enter the subnet mask used for your

network.

7. Press [

Enter], then [S] (for Save).

Here is some information on the fields in the Setup screen. For more information on these fields, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com:

Parameter Default

System Name blank Optional; up to 25 characters, including spaces

System Contact blank Optional; up to 48 characters, including spaces

Manager Password blank Recommended; up to 16 characters (no blank spaces)

Configuring the Switch

Logon Default CLI The default setting selects the command line interface for console access.

The alternative is the menu interface.

Time Zone 0 (none) Optional; 1440 to -1440. The number of minutes your location is to the West (-)

or East (+) of GMT.

Community Name public Default setting recommended.

Spanning Tree Enabled No Default setting recommended unless STP is already running on your network

or the switch will be used in complex network topologies.

Default Gateway blank Optional; Enter the IP address of the next-hop gateway node if network traffic

needs to be able to reach off-subnet destinations.

Time Sync Method None Optional; The protocol the switch uses to acquire a time signal. The options

are SNTP and TimeP.

TimeP Mode Disabled Optional; The method the switch uses to acquire the TimeP server address.

IP Config (DHCP/Bootp) DHCP/Bootp Set to Manual unless a DHCP/Bootp server is used on your network to

configure IP addressing.

IP Address xxx.xxx.xxx.xxx Recommended; If you set IP Config to Manual, then enter an IP address

compatible with your network.

Note: The IP address and subnet mask assigned for the switch must be compatible with the IP addressing used in your network. For more information on IP addressing, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Subnet Mask xxx.xxx.xxx.xxx Recommended; If you entered an IP address, then enter a subnet mask

compatible with your network.

Configuring the Switch

3-3

Page 44

Configuring the Switch

Where to Go From Here

The above procedure configures your switch with a Manager password, IP address, and subnet mask. As a result, with the proper network connections, you can now manage the switch from a PC equipped with Telnet or a web browser interface.

Some basic information on managing your switch is included in the next section. For more information on the console, web browser, and SNMP management interfaces and all the features that can be configured on the Series 2510 Switch devices, please see the Management and Configuration

Guide, which is available on the ProCurve Networking Web site,

www.procurve.com.

To Recover from a Lost Manager Password: If you cannot start a console session at the manager level because of a lost Manager password, you can clear all passwords and user names by getting physical access to the switch and pressing and holding the Clear button for a full second.

Configuring the Switch

3-4

Page 45

Using the IP Address for Remote Switch Management

Configuring the Switch

Using the IP Address for Remote Switch Management

With the Series 2510 Switch, you can use the switch’s IP address to manage the switch from any PC that is on the same subnet as the switch. You can use either a Telnet session or a standard web browser to manage the switch.

Starting a Telnet Session

To access the switch through a Telnet session, follow these steps:

1. Make sure the switch is configured with an IP address and that the switch is reachable from the PC that is running the Telnet session (for example, by using a Ping command to the switch’s IP address).

2. Start the Telnet program on a PC that is on the same subnet as the switch and connect to the switch’s IP address.

3. You will see the copyright page and the message “Press any key to continue”. Press a key, and you will then see the switch console command (CLI) prompt, for example:

ProCurve Switch 2510-24#

Enter help or ? to see a list of commands that can be executed at the prompt. Entering any command followed by help provides more detailed context help information about the command. Entering any command followed by ? displays a list of options that are available at that point in the command entry.

Starting a Web Browser Session

The Series 2510 Switch, can be managed through a graphical interface that you can access from any PC or workstation on the network by running your web browser and typing in the switch’s IP address as the URL. No additional software installation is required to make this interface available; it is included in the switch’s onboard software.

A typical web browser interface screen is shown in the next illustration.

3-5

Configuring the Switch

Page 46

Configuring the Switch

Using the IP Address for Remote Switch Management

For more information on using the web browser interface, please see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Configuring the Switch

An extensive help system is also available for the web browser interface. To access the help system though the subnet on which the switch is installed you must have access to the internet.

3-6

Page 47

Troubleshooting

This chapter describes how to troubleshoot the Series 2510 Switch. This document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting on the Series 2510 Switch using the software tools available with the switch, including the full-featured console interface, the built-in web browser interface. For more information, see the chapter “Troubleshooting” in the Management and Configuration

Guide, which is available on the ProCurve Networking Web site,

www.procurve.com.

This chapter describes the following:

■ basic troubleshooting tips (page 4-1)

■ diagnosing with the LEDs (page 4-4)

■ Proactive Networking tools (page 4-8)

■ hardware diagnostic tests (page 4-9)

■ restoring the factory default configuration (page 4-11)

■ downloading new software to the Series 2510 Switch (page 4-12)

■ ProCurve Customer Support Services (page 4-12)

Basic Troubleshooting Tips

Most problems are caused by the following situations. Check for these items first when starting your troubleshooting:

■ Connecting to devices that have a fixed full-duplex configuration.

The RJ-45 ports are configured as “Auto”. That is, when connecting to attached devices, the switch will operate in one of two ways to determine the link speed and the communication mode (half duplex or full duplex):

• If the connected device is also configured to Auto, the switch will

automatically negotiate both link speed and communication mode.

• If the connected device has a fixed configuration, for example

100 Mbps, the link speed, but will default to a communication mode of half duplex.

at half or full duplex, the switch will automatically sense

4-1

Troubleshooting

Page 48

Troubleshooting

Basic Troubleshooting Tips

Because the Series 2510 Switch behaves in this way (in compliance with the IEEE 802.3 standard), if a device connected to the switch has a fixed

configuration at full duplex, the device will not connect correctly to the switch. The result will be high error rates and very inefficient communications between the switch and the device.

Make sure all devices connected to the Series 2510 Switch are configured to auto negotiate, or are configured to connect at half duplex (all hubs are configured this way, for example).

■ Faulty or loose cables. Look for loose or obviously faulty connections.

If they appear to be OK, make sure the connections are snug. If that does not correct the problem, try a different cable.

■ Non-standard cables. Non-standard and miswired cables may cause

network collisions and other network problems, and can seriously impair network performance. Use a new correctly-wired cable or compare your cable to the cable in appendix B, “Twisted-Pair Cable/Connector Pin-Outs”

on page 5 for pinouts and correct cable wiring. A category 5 cable tester

is a recommended tool for every 100Base-TX network installation.

■ Improper Network Topologies. It is important to make sure you have

a valid network topology. Common topology faults include excessive cable length and excessive repeater delays between end nodes. If you have network problems after recent changes to the network, change back to the previous topology. If you no longer experience the problems, the new topology is probably at fault. Sample topologies are shown at the end of chapter 2 in this book, and some topology configuration guidelines can be found on the ProCurve Web site,

/www.procurve.com.

Troubleshooting

In addition, you should make sure that your network topology contains no data path loops. Between any two end nodes, there should be only one active cabling path at any time. Data path loops will cause broadcast storms that will severely impact your network performance.

For your Series 2510 Switch, if you wish to build redundant paths between important nodes in your network to provide some fault tolerance, you should enable Spanning Tree Protocol support on the switch. This ensures that only one of the redundant paths is active at any time, thus avoiding data path loops. Spanning Tree can be enabled through the switch console or the web browser interface.

The Series 2510 Switch also supports Trunking, which allows multiple network cables to be used for a single network connection without causing a data path loop. For more information on Spanning Tree and Trunking, see the Management and Configuration Guide, which is avail- able on the ProCurve Networking Web site, www.procurve.com.

4-2

Page 49

Basic Troubleshooting Tips

■ Check the port configuration. A port on your Switch may not be

Troubleshooting

operating as you expect because it has been put into a “blocking” state by Spanning Tree, GVRP (automatic VLANs), or LACP (automatic trunking). (Note that the normal operation of the Spanning Tree, GVRP, and LACP features may put the port in a blocking state.) Or, the port just may have been configured as disabled through software.

Use the switch console to determine the port’s configuration and verify that there is not an improper or undesired configuration of any of the switch features that may be affecting the port. For more information, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

For more information on possible network problems and their solutions, refer to the technical note “Troubleshooting LAN Performance and Intermittent Connectivity Problems”, which can be found on the ProCurve Web site,

www.procurve.com, in the Information Library section.

4-3

Troubleshooting

Page 50

Troubleshooting

Diagnosing with the LEDs

Table 3-1 shows LED patterns on the switch and the switch modules that indicate problem conditions.

1. Check in the table for the LED pattern you see on your switch.

2. Refer to the corresponding diagnostic tip on the next few pages.

Table 4-1. LED Error Indicators

LED Pattern Indicating Problems

Power Fault Self Test Port LED

Off * * *

On Prolonged On Prolonged On *

On Blinking

On Off Off Off with cable

On Off Off On, but the port is not

* This LED is not important for the diagnosis.

†

The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

†

Blinking

†

(in Link view mode)

†

Blinking

connected

communicating

Diagnostic Tips

➊

➋

➌

➍

➎

➏

Troubleshooting

4-4

Page 51

Diagnostic Tips:

Tip Problem Solution

Diagnosing with the LEDs

Troubleshooting

➊

➋

➌

➍

The switch is not plugged into an active AC power source, or the switch’s power supply may have failed.

A switch hardware failure has occurred. All the LEDs will stay on indefinitely.

The switch has experienced a software failure during self test.

The network port for which the LED is blinking has experienced a self test or initialization failure

1. Verify the power cord is plugged into an active power source and to the switch. Make sure these connections are snug.

2. Try power cycling the switch by unplugging and plugging the power cord back in.

3. If the Power LED is still not on, verify that the AC power source works by plugging another device into the outlet. Or try plugging the switch into a different outlet or try a different power cord.

If the power source and power cord are OK and this condition persists, the switch power supply may have failed. Call your ProCurve authorized LAN dealer, or use the electronic support services from ProCurve to get assistance. See the Customer Support/Warranty booklet for more information.

Try power cycling the switch. If the fault indication reoccurs, the switch may have failed. Call your ProCurve authorized LAN dealer, or use the electronic support services from ProCurve to get assistance. See the Customer Support/Warranty booklet for more information.

1. Try resetting the switch by pressing the Reset button on the front of the switch, or by power cycling the switch.

2. If the fault indication reoccurs, attach a console to the switch (as indicated in chapter

2) and configure it to operate at 9600 baud. Then, reset the switch. Messages should appear on the console screen and in the console log identifying the error condition. You can view the console log at that point by selecting it from the console Main Menu.

If necessary to resolve the problem, contact your ProCurve authorized LAN dealer, or use the electronic support services from ProCurve to get assistance. See the Customer Support/Warranty booklet for more information.

Try power cycling the switch. If the fault indication reoccurs, the switch port may have failed. Call your ProCurve authorized LAN dealer, or use the electronic support services from ProCurve to get assistance. See the Customer Support/Warranty booklet for more information.

If the port is a mini-GBIC, verify that it is one of the mini-GBICs supported by the switch. Unsupported mini-GBICs will be identified with this fault condition. The supported miniGBICs are listed in Chapter 2, “Installing the Switch” on page 2-7. The mini-GBICs are also tested when they are “hot-swapped”—installed or changed while the switch is powered on.

To verify the port has failed, try removing and reinstalling the mini-GBIC without having to power off the switch. If the port fault indication reoccurs, you will have to replace the mini-GBIC.

Troubleshooting

continued on the next page

4-5

Page 52

Troubleshooting

Diagnosing with the LEDs

Tip Problem Solution

➎

The network connection is not working properly.

Try the following procedures:

• For the indicated port, verify both ends of the cabling, at the switch and the connected device, are connected properly.

• Verify the connected device and switch are both powered on and operating correctly.

• Verify you have used the correct cable type for the connection: – For twisted-pair connections to the fixed 10/100 ports, if the port is configured to

“Auto” (auto negotiate), either straight-through or crossover cables can be used because of the switch’s Auto MDI/MDI-X feature of the 10/100-Base-TX port.

Note: If the switch port configuration is changed to one of the fixed configuration options (for example, 100 Mbps/Full Duplex), then the port operates as MDI-X only and you must use the correct type of cable for the connection. In general, for connecting an end node (MDI port) to the switch, use straight-through cable; for connecting to MDI-X ports on hubs, other switches, and routers, use crossover cable.

– For fiber-optic connections, verify that the transmit port on the switch is connected

to the receive port on the connected device, and the switch receive port is connected to the transmit port on the connected device.

• For the dual-personality 10/100/1000Base-T ports, be sure a mini-GBIC is not installed in the associated slot.

The cable verification process must include all patch cables from any end devices, including the switch, to any patch panels in the cabling path.

• Verify the port has not been disabled through a switch configuration change. You can use the console interface, or, if you have configured an IP address on the

switch, use the web browser interface to determine the state of the port and re-enable the port if necessary.

• Verify the switch port configuration matches the configuration of the attached device. For example, if the switch port is configured as “Auto”, the port on the attached device also MUST be configured as “Auto”. Depending on the port type, twisted-pair or fiberoptic, if the configurations don’t match, the results could be a very unreliable connection, or no link at all.

• If the other procedures don’t resolve the problem, try using a different port or a different cable.

Troubleshooting

continued on the next page

4-6

Page 53

Tip Problem Solution

Diagnosing with the LEDs

Troubleshooting

➏

The port may be improperly configured, or the port may be in a “blocking” state by the normal operation of the Spanning Tree, LACP, or IGMP features.

Use the switch console to see if the port is part of a dynamic trunk (through the LACP feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may have been put into a “blocking” state by those features. The show lacp command displays the port status for the LACP feature; the show spanning-tree command displays the port status for Spanning Tree.

Also check the Port Status screen using the show interfaces command to see if the port has been configured as “disabled”.

Other switch features that may affect the port operation include VLANs and IGMP. Use the switch console to see how the port is configured for these features.

For software troubleshooting tips, see the chapter “Troubleshooting” in the Management

and Configuration Guide, which is available on the ProCurve Networking Web site,

www.procurve.com.

Make sure also, that the device at the other end of the connection is indicating a good link to the switch. If it is not, the problem may be with the cabling between the devices or the connectors on the cable.

4-7

Troubleshooting

Page 54

Troubleshooting

Proactive Networking

The ProCurve Series 2510 Switch devices have built-in management capabilities that proactively help you manage your network including:

■ finding and helping you fix the most common network error conditions

(for example, faulty network cabling, and non-standard network topologies)

■ informing you of the problem with clear, easy-to-understand messages

■ recommending network configuration changes to enhance the perfor-

mance of your network

The following interfaces provide tests, indicators, and an event log that can be used to monitor the switch and its network connections and to help you take advantage of these proactive networking features:

■ A graphical web browser interface that you can use to manage your switch

from a PC running a supported web browser, for example Microsoft Internet Explorer, and Netscape Communicator.

■ A full-featured easy-to-use console interface that you can access by

connecting a standard terminal or PC running a terminal emulator to the switch’s console port. The cable to make that connection is provided with your switch. The console interface is also accessible through a Telnet connection.

Troubleshooting

For more information on using these software tools to diagnose and manage your switch, see the “Troubleshooting” chapter in the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

4-8

Page 55

Hardware Diagnostic Tests

Troubleshooting

Hardware Diagnostic Tests

Testing the Switch by Resetting It

If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either:

■ Unplug and plug in the power cord (power cycling)

■ Press the Reset button on the front of the switch

Power cycling the switch and pressing the Reset button both cause the switch to perform its power-on self test, which almost always will resolve any temporary operational problems. These reset processes also cause any network traffic counters to be reset to zero, and cause the System Up Time timer to reset to zero.

Checking the Switch LEDs

The self test passes if the Fault and Test LEDs on the front of the switch go off after approximately 50 seconds. If these LEDs stay on longer than 60 seconds or begin blinking, there may be a problem with the switch.

See “Diagnosing With the LEDs” on page 4-4 for information on interpreting the LED patterns and LED behaviors in chapter one.

Checking Console Messages

Useful diagnostic messages may be displayed on the console screen when the switch is reset. To connect a PC running a VT-100 terminal emulator program or a standard VT-100 terminal to the switch’s Console Port and configure it to run at 9600 baud, and with the other terminal communication settings shown on page 2-17. Then, when you reset the switch, note the messages that are displayed. Additionally, you can check the switch event log, which can be accessed from the console using the show log command, or from the console Main Menu.

4-9

Troubleshooting

Page 56

Troubleshooting

Hardware Diagnostic Tests

Testing Twisted-Pair Cabling

Network cables that fail to provide a link or provide an unreliable link between the switch and the connected network device may not be compatible with the IEEE 802.3 Type 10Base-T, 100Base-TX. The twisted-pair cables attached to the Switch must be compatible with the appropriate standards. To verify your cable is compatible with these standards, use a qualified cable test device.

Testing Switch-to-Device Network Communications

You can perform the following communication tests to verify the network is operating correctly between the switch and any connected device that can respond correctly to the communication test.

■ Link Test -- a physical layer test that sends IEEE 802.2 test packets to any

device identified by its MAC address

■ Ping Test -- a network layer test used on IP networks that sends test

packets to any device identified by its IP address

These tests can be performed through the switch console interface from a terminal connected to the switch or through a Telnet connection, or from the switch’s web browser interface. For more information, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

Troubleshooting

Testing End-to-End Network Communications

Both the switch and the cabling can be tested by running an end-to-end communications test -- a test that sends known data from one network device to another through the switch. For example, if you have two PCs on the network that have LAN adapters between which you can run a link-level test or Ping test through the switch, you can use this test to verify that the entire communication path between the two PCs is functioning correctly. See your LAN adapter documentation for more information on running a link test or Ping test.

4-10

Page 57

Restoring the Factory Default Configuration

Troubleshooting

Restoring the Factory Default Configuration

As part of your troubleshooting process on the Switch, it may become necessary to return the switch configuration to the factory default settings. This process momentarily interrupts the switch operation, clears any passwords, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the switch into its factory default configuration including deleting the IP address, if one is configured.

Note This process removes all switch configuration changes you have made from

the factory default settings. This includes, for example, configuration of VLANs, Spanning Tree, trunks, and stacking. Returning the configuration of these features to their factory default settings (usually disabling them) may result in network connectivity issues.

If the switch has a valid configuration, and you are restoring the factory default settings for a reason other than configuration problems, you should save the switch configuration prior to performing the factory default reset. Then, after the reset and resolution of the original problem, you can restore the saved configuration to the switch. For both the save and restore processes, you can use the console copy command. For more information on this command, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

You can restore the factory default configuration either on the switch itself, or through the switch console.

To execute the factory default reset on the switch, perform these steps:

1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.

2. Continue to press the Clear button while releasing the Reset button.

3. When the Test LED begins to blink, release the Clear button.

The switch will then complete its self test and begin operating with its configuration restored to the factory default settings.

To restore the factory default configuration using the console, execute the erase startup-config command from the console command prompt.

4-11

Troubleshooting

Page 58

Troubleshooting

Downloading New Switch Software

When product enhancements occur for the Series 2510 Switch, new software can be downloaded to the switch through several methods, for product enhancements and new features. For more information, see the Management and Configuration Guide, which is available on the ProCurve Networking Web site, www.procurve.com.

The new switch software would be available on the ProCurve Web site,

www.procurve.com.

ProCurve Customer Support Services

If you are still having trouble with your switch, Hewlett-Packard offers support 24 hours a day, seven days a week through the use of a number of automated electronic services. See the Customer Support/Warranty booklet that came with your switch for information on how to use these services to get technical support. The ProCurve Web site, support information.

www.procurve.com also provides up-to-date

Troubleshooting

4-12

Additionally, your ProCurve authorized network reseller can provide you with assistance, both with services they offer and with services offered by ProCurve.

Before Calling Support

Before Support, to make the process most efficient, you first should have retrieved the following information:

Information Item Information Location

• product identification, including miniGBICs

• details about the switch’s status including the software (OS) version, a copy of the switch configuration, a copy of the switch Event Log, and a copy of the switch status and counters information

• copy of your network topology map, including network addresses assigned to the relevant devices

the front of the switch, and on labels on the mini-GBICs

switch console: show tech command

your network records

Page 59

Switch Specifications

Physical

Width: 44.3 cm (17.42 in)

Depth: 23.5 cm (9.3 in)

Height: 4.4 cm (1.73 in)

Weight: 2.2 kg (4.9 lbs)

Switch Specifications

2510-24 (J9019A)

Electrical

The switch automatically adjusts to any voltage between 100-127 and 200-240 volts and either 50 or 60 Hz.

AC voltage: 100-127/200-240 volts

Maximum current: 0.75 A / 0.40 A

Frequency range: 50-60 Hz

2510-24 (J9019A)

Environmental

Operating Non-Operating

Temperature: 0°C to 45°C (32°F to 113°F) -40°C to 70°C (-40°F to 158°F)

Relative humidity: (non-condensing)

Maximum altitude: 2 km (6,500 ft) 4.6 km (15,000 ft)

15% to 95% at 40°C (104°F) 15% to 90% at 65°C (149°F)

A-1

Page 60

Switch Specifications

Connectors

■ The 10/100 Mbps RJ-45 twisted-pair ports are compatible with the

following standards:

• IEEE 802.3u 100Base-TX

• IEEE 802.3 10Base-T

■ The 1000 Mbps LC fiber-optic ports on the Gigabit-SX and Gigabit-LX

mini- GBIC transceivers are compatible with the IEEE 802.3z Gigabit-SX and Gigabit-LX standards.

Safety

Complies with:

■ EN60950 / IEC 950

■ CSA 22.2 No. 950

■ UL 60950

Lasers

The Gigabit-SX LC mini-GBIC, and the Gigabit-LX LC mini-GBIC, both of which can be installed in the Series 2510 Switch, are Class 1M Laser Products.

Laser Radiation: Do not view directly with optical instruments. Class 1M laser product.

Laser Klasse 1M These mini-GBICs comply with IEC 825-2: 1993.

A-2

Page 61

Switch Ports and Network Cables

This appendix includes switch connector information and network cable information for cables that should be used with the Series 2510 Switch, including minimum pin-out information and specifications for twisted-pair cables.

Note Incorrectly wired cabling is the most common cause of problems for LAN

communications. ProCurve recommends that you work with a qualified LAN cable installer for assistance with your cabling requirements.

Switch Ports

The fixed RJ-45 10/100Base-TX ports on the switch accept 100-ohm unshielded and shielded twisted-pair cable with RJ-45 connectors as described on the next page.

Twi sted -Pair Cab les

10 Mbps Operation Category 3, 4, or 5 100-ohm unshielded twisted-pair (UTP)

or shielded twisted-pair (STP) cable, complying with IEEE

802.3 Type 10Base-T specifications, fitted with RJ-45 connectors

100 Mbps Operation Category 5 100-ohm UTP or STP cable, complying with

IEEE 802.3u 100Base-TX specifications, fitted with RJ-45 connectors

1000 Mbps Operation Category 5 100-ohm 4-pair UTP or STP cable, complying

with IEEE 802.3ab 1000Base-T specifications, fitted with RJ-45 connectors—Category 5e or better is recommended

(please see “Note on 1000Base-T Cable Requirements”, below)

Switch Ports and Network

Cables

Note on 1000Base-T Cable Requirements. The Category 5 networking cables that work for 100Base-TX connections should also work for 1000Base-T, as long as all four-pairs are connected. But, for the most robust connections you should use cabling that complies with the Category 5e specifications, as described in Addendum 5 to the TIA-568-A standard (ANSI/ TIA/EIA-568-A-5).

B-1

Page 62

Switch Ports and Network Cables

Because of the increased speed provided by 1000Base-T (Gigabit-T), network cable quality is more important than for either 10Base-T or 100Base-TX. Cabling plants being used to carry 1000Base-T networking must comply with the IEEE 802.3ab standards. In particular, the cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT). Additionally, unlike the cables for 100Base-TX, the 1000Base-T cables must pass tests for Equal-Level Far-End Crosstalk (ELFEXT) and Return Loss.

When testing your cabling, be sure to include the patch cables that connect the switch and other end devices to the patch panels on your site. The patch cables are frequently overlooked when testing cable and they must also comply with the cabling standards.

Fiber-Optic

Switch Ports and Network

Cables

1000Base-SX 62.5/125 μm or 50/125 μm (core/cladding) diameter, graded-

index, multimode fiber-optic cables, complying with the ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a respectively, fitted with LC connectors.

1000Base-LX single mode fiber-optic cables, complying with the ITU-T

G.652 and ISO/IEC 793-2 Type B1 standards, fitted with LC connectors

62.5/125 μm or 50/125 μm (core/cladding) diameter, graded- index, multimode fiber-optic cables, complying with the ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a respectively, fitted with LC connectors

Note: Multimode fiber-optic cabling may be used for a 1000Base-LX application, but a mode conditioning patch cord may be needed. See “Mode Conditioning Patch Cord

for Gigabit-LX” on page B-3 for more information.

1000Base-LH single mode fiber-optic cables, complying with the ITU-T

G.652 and ISO/IEC 793-2 Type B1 standards, fitted with LC connectors

B-2

Page 63

Mode Conditioning Patch Cord for Gigabit-LX

Switch Ports and Network Cables

Mode Conditioning Patch Cord for Gigabit-LX

The following information applies to installations in which multimode fiberoptic cables are connected to a Gigabit-LX port.

Unlike Gigabit-SX, which connects to only multimode fiber-optic cabling, Gigabit-LX can use either single-mode or multimode cable. Multimode cable has a design characteristic called “Differential Mode Delay”, which requires that the transmission signals be “conditioned” to compensate for the cable design and thus prevent resulting transmission errors. Since Gigabit-SX is designed to operate only with multimode cable, Gigabit-SX mini-GBICs can provide that transmission conditioning internally.

Switch Ports and Network

Gigabit-LX mini-GBICs, since they are designed to operate with both singlemode and multimode cable, do not provide the transmission conditioning internally. Thus, under certain circumstances, depending on the cable used and the lengths of the cable runs, an external Mode Conditioning Patch Cord may need to be installed between the Gigabit-LX transmitting device and the multimode network cable to provide the transmission conditioning.

If you experience a high number of transmission errors on the Gigabit-LX ports, usually CRC or FCS errors, you may need to install one of these patch cords between the Gigabit-LX port in your switch and your multimode fiberoptic network cabling, and between the Gigabit-LX transmission device and the network cabling at the other end of the multimode fiber-optic cable run. A patch cord must be installed at both ends.

The patch cord consists of a short length of single-mode fiber cable coupled to graded-index multimode fiber cable on the transmit side, and only multimode cable on the receive side. The section of single-mode fiber is connected in such a way that it minimizes the effects of the differential mode delay in the multimode cable.

Note Most of the time, if you are using good quality graded-index multimode fiber

cable that adheres to the standards listed on need to use mode conditioning patch cords in your network. This is especially true if the fiber runs in your network are relatively short.

If you are using single-mode fiber-optic cabling in your network, there is no need to use mode conditioning patch cords. Connect the single-mode network cable directly to the Gigabit-LX mini-GBIC.

page 2-6, there should not be a

Cables

B-3

Page 64

Switch Ports and Network Cables

Mode Conditioning Patch Cord for Gigabit-LX

Cables

Installing the Patch Cord

As shown in the illustration below, connect the patch cord to the Gigabit-LX mini-GBIC with the section of single-mode fiber plugged in to the Tx (transmit) port. Then, connect the other end of the patch cord to your network cabling patch panel, or directly to the network multimode fiber.

If you connect the patch cord directly to the network cabling, you may need to install a female-to-female adapter to allow the cables to be connected together.

To network

multimode

cabling

Gigabit-LX port

Mode Conditioning

Patch Cord

Switch Ports and Network

The multimode cable in the patch cord must match the characteristics of your

network cable

Single-mode section plugs in to Tx

port on Gigabit-LX Transceiver or

Gigabit-LX mini-GBIC

Make sure you purchase a patch cord that has LC connectors on the end that connects to the Gigabit-LX mini-GBIC, and has multimode fibers that match the characteristics of the multimode fiber in your network.

B-4

Page 65

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

If you connect a Series 2510 Switch twisted-pair port to another switch or hub, which typically have MDI-X ports, the Series 2510 Switch port automatically operates as an MDI port. If you connect it to an end node, such as a server or PC, which typically have MDI ports, the Series 2510 Switch port operates as an MDI-X port. In all cases, you can use standard straight through cables or crossover cables.

If you happen to use a correctly wired crossover cable, though, the switch will still be able to automatically detect the MDI/MDI-X operation and link correctly to the connected device.

Note Using Fixed Configurations. If the port configuration is changed to any of

the fixed configurations though, for example 100 Mbps/full duplex, the port operates as MDI-X only and the correct cable type must be used: for connections to MDI ports, such as end nodes, use a straight-through cable; for connections to MDI-X ports, such as on hubs and other switches, use a crossover cable.

Other Wiring Rules:

■ All twisted-pair wires used for 10 Mbps, and 100 Mbps operation must be

twisted through the entire length of the cable. The wiring sequence must conform to EIA/TIA 568-B (not USOC). See “Twisted-Pair Cable Pin Assignments” later in this appendix for a listing of the signals used on each pin.

■ For 10 Mbps connections to the ports, you can use Category 3, 4, or 5

unshielded twisted-pair cable, as supported by the IEEE 802.3 Type 10Base-T standard.

■ For 100 Mbps connections to the ports, use 100-ohm Category 5 UTP or

STP cable only, as supported by the IEEE 802.3u Type 100Base-TX standard.

Switch Ports and Network

Cables

B-5

Page 66

Switch Ports and Network

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections

Because of the MDI/MDI-X operation of the 10/100 ports on the switch, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use “straight-through” cables.

If any of these ports are given a fixed configuration, for example 100 Mbps/ Full Duplex, the ports operate as MDI-X ports, and straight-through cables must be then used for connections to PC NICs and other MDI ports.

Cable Diagram

Cables

Note Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2

on connector “B”. Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 3 and 6 on connector “B”. Pins 4, 5, 7, and 8 are not used in this application, although they may be wired in the cable.

Pin Assignments

Switch End (MDI-X) Computer, Transceiver, or

Other End

Signal Pins Pins Signal

receive + receive transmit + transmit -

B-6

1 2 3 6

transmit + transmit receive + receive -

Page 67

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection

The MDI/MDI-X operation of the 10/100 ports on the switch also allows you to use “crossover” cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches.

If any of these ports are given a fixed configuration, for example 100 Mbps/ Full Duplex, the ports operate as MDI-X ports, and crossover cables must be then used for connections to hubs or switches or other MDI-X network devices.

Cable Diagram

Note Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 3 and 6

on connector “B”. Pins 3 and 6 on connector “A” must be wired as a twisted pair to pins 1 and 2 on connector “B”. Pins 4, 5, 7, and 8 are not used in this application, although they may be wired in the cable.

Pin Assignments

Switch Ports and Network

Cables

Switch End (MDI-X) Hub or Switch Port, or Other

MDI-X Port End

Signal Pins Pins Signal

receive + receive transmit + transmit -

1 2 3 6

6 3 2 1

transmit transmit + receive receive +

B-7

Page 68

Switch Ports and Network

Switch Ports and Network Cables

Twisted-Pair Cable/Connector Pin-Outs

Cables

B-8

Page 69

Safety and EMC Regulatory Statements

Safety Information

Documentation reference symbol. If the product is marked with this

symbol, refer to the product documentation to get more information about the product.

WARNING A WARNING in the manual denotes a hazard that can cause injury

or death.

Caution A Caution in the manual denotes a hazard that can damage equip-

ment.

Do not proceed beyond a WARNING or Caution notice until you have understood the hazardous conditions and have taken appropriate steps.

Grounding

These are safety class I products and have protective earthing terminals. There must be an uninterruptible safety earth ground from the main power source to the product's input wiring terminals, power cord, or supplied power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until the ground has been restored.

For LAN cable grounding:

■ If your LAN covers an area served by more than one power distribu-

tion system, be sure their safety grounds are securely interconnected.

■ LAN cables may occasionally be subject to hazardous transient volt-

ages (such as lightning or disturbances in the electrical utilities power grid). Handle exposed metal components of the network with caution.

Servicing

There are no user-serviceable parts inside these products. Any servicing, adjustment, maintenance, or repair must be performed only by service-trained personnel.

Safety and EMC Regulatory

Statements

These products do not have a power switch; they are powered on when the power cord is plugged in.

C-1

Page 70

Safety and EMC Regulatory Statements

Informations concernant la sécurité

Symbole de référence à la documentation. Si le produit est marqué de

ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées.

Safety and EMC Regulatory

WARNING Dans la documentation, un WARNING indique un danger susceptible

d'entraîner des dommages corporels ou la mort.

Caution Un texte de mise en garde intitulé Caution indique un danger suscep-

tible de causer des dommages à l'équipement.

Ne continuez pas au-delà d'une rubrique WARNING ou Csution avant d'avoir bien compris les conditions présentant un danger et pris les mesures appropriées.

Cet appareil est un produit de classe I et possède une borne de mise à la terre. La source d'alimentation principale doit être munie d'une prise de terre de sécurité installée aux bornes du câblage d'entrée, sur le cordon d'alimentation ou le cordon de raccordement fourni avec le produit. Lorsque cette protection semble avoir été endommagée, débrancher le cordon d'alimentation jusqu'à ce que la mise à la terre ait été réparée.

Mise à la terre du câble de réseau local:

■ si votre réseau local s'étend sur une zone desservie par plus d'un système de

distribution de puissance, assurez-vous que les prises de terre de sécurité soient convenablement interconnectées.

■ Les câbles de réseaux locaux peuvent occasionnellement être soumis à des

surtensions transitoires dangereuses (telles que la foudre ou des perturbations dans le réseau d'alimentation public). Manipulez les composants métalliques du réseau avec précautions.

Statements

Aucune pièce contenue à l'intérieur de ce produit ne peut être réparée par l'utilisateur. Tout dépannage, réglage, entretien ou réparation devra être confié exclusivement à un personnel qualifié.

C-2

Cet appareil ne comporte pas de commutateur principal ; la mise sous tension est effectuée par branchement du cordon d'alimentation.

Page 71

Hinweise zur Sicherheit

Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem

Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten.

Safety and EMC Regulatory Statements

Hinweise zur Sicherheit

WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die

Verletzungen oder sogar Todesfälle verursachen kann.

Caution Caution in der Dokumentation symbolisiert eine Gefahr, die dis Gerät

beschädigen kann.

Fahren Sie nach dem Hinweis WARNING oder Caution erst fort, nachdem Sie den Gefahrenzustand verstanden und die entsprechenden Maßnahmen ergriffen haben.

Dies ist ein Gerät der Sicherheitsklasse I und verfügt über einen schützenden Erdungsterminal. Der Betrieb des Geräts erfordert eine ununterbrochene Sicherheitserdung von der Hauptstromquelle zu den Geräteingabeterminals, den Netzkabeln oder dem mit Strom belieferten Netzkabelsatz voraus. Sobald Grund zur Annahme besteht, daß der Schutz beeinträchtigt worden ist, das Netzkabel aus der Wandsteckdose herausziehen, bis die Erdung wiederhergestellt ist.

Für LAN-Kabelerdung:

■ Wenn Ihr LAN ein Gebiet umfaßt, das von mehr als einem Stromverteilungs-

system beliefert wird, müssen Sie sich vergewissern, daß die Sicherheitserdungen fest untereinander verbunden sind.

■ LAN-Kabel können gelegentlich gefährlichen Übergangsspannungen aus-

gesetzt werden (beispielsweise durch Blitz oder Störungen in dem Starkstromnetz des Elektrizitätswerks). Bei der Handhabung exponierter Metallbestandteile des Netzwerkes Vorsicht walten lassen.

Dieses Gerät enthält innen keine durch den Benutzer zu wartenden Teile. Wartungs-, Anpassungs-, Instandhaltungs- oder Reparaturarbeiten dürfen nur von geschultem Bedienungspersonal durchgeführt werden.

Safety and EMC Regulatory

Statements

Dieses Gerät hat keinen Netzschalter; es wird beim Anschließen des Netzkabels eingeschaltet.

C-3

Page 72

Safety and EMC Regulatory Statements

Considerazioni sulla sicurezza

Simbolo di riferimento alla documentazione. Se il prodotto è contras-

segnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso.

Safety and EMC Regulatory

Statements

WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o

morte.

Caution La dicituraCaution denota un pericolo che può danneggiare le attrez-

zature.

Non procedere oltre un avviso di WARNING o di Caution prima di aver compreso le condizioni di rischio e aver provveduto alle misure del caso.

Questo prodotto è omologato nella classe di sicurezza I ed ha un terminale protettivo di collegamento a terra. Dev'essere installato un collegamento a terra di sicurezza, non interrompibile che vada dalla fonte d'alimentazione principale ai terminali d'entrata, al cavo d'alimentazione oppure al set cavo d'alimentazione fornito con il prodotto. Ogniqualvolta vi sia probabilità di danneggiamento della protezione, disinserite il cavo d'alimentazione fino a quando il collegaento a terra non sia stato ripristinato.

Per la messa a terra dei cavi LAN:

■ se la vostra LAN copre un'area servita da più di un sistema di distribuzione

elettrica, accertatevi che i collegamenti a terra di sicurezza siano ben collegati fra loro;

■ i cavi LAN possono occasionalmente andare soggetti a pericolose tensioni

transitorie (ad esempio, provocate da lampi o disturbi nella griglia d'alimentazione della società elettrica); siate cauti nel toccare parti esposte in metallo della rete.

Nessun componente di questo prodotto può essere riparato dall'utente. Qualsiasi lavoro di riparazione, messa a punto, manutenzione o assistenza va effettuato esclusivamente da personale specializzato.

C-4

Questo apparato non possiede un commutatore principale; si mette scotto tensione all'inserirsi il cavo d'alimentazione.

Page 73

Safety and EMC Regulatory Statements

Consideraciones sobre seguridad

Símbolo de referencia a la documentación. Si el producto va

marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto.

WARNING Una WARNING en la documentación señala un riesgo que podría

resultar en lesiones o la muerte.

Caution Una Caution en la documentación señala un riesgo que podría

resultar en averías al equipo.

No proseguir después de un símbolo de WARNING o Caution hasta no haber entendido las condiciones peligrosas y haber tomado las medidas apropiadas.

Este aparato se enmarca dentro de la clase I de seguridad y se encuentra protegido por una borna de puesta a tierra. Es preciso que exista una puesta a tierra continua desde la toma de alimentación eléctrica hasta las bornas de los cables de entrada del aparato, el cable de alimentación o el juego de cable de alimentación suministrado. Si existe la probabilidad de que la protección a tierra haya sufrido desperfectos, desenchufar el cable de alimentación hasta haberse subsanado el problema.

Puesta a tierra del cable de la red local (LAN):

■ Si la LAN abarca un área cuyo suministro eléctrico proviene de más de una

red de distribución de electricidad, cerciorarse de que las puestas a tierra estén conectadas entre sí de modo seguro.

■ Es posible que los cables de la LAN se vean sometidos de vez en cuando a

voltajes momentáneos que entrañen peligro (rayos o alteraciones en la red de energía eléctrica). Manejar con precaución los componentes de metal de la LAN que estén al descubierto.

Este aparato no contiene pieza alguna susceptible de reparación por parte del usuario. Todas las reparaciones, ajustes o servicio de mantenimiento debe realizarlos solamente el técnico.

Safety and EMC Regulatory

Statements

Este producto no tiene interruptor de potencia; se activa cuando se enchufa el cable de alimentación.

C-5

Page 74

Safety and EMC Regulatory Statements

Safety Information (Japan)

Safety and EMC Regulatory

Statements

Japan Power Cord Warning

C-6

Page 75

Safety and EMC Regulatory Statements

Safety Information (China)

C-7

Safety and EMC Regulatory

Statements

Page 76

Safety and EMC Regulatory Statements

EMC Regulatory Statements

U.S.A.

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment in a residential area may cause interference in which case the user will be required to correct the interference at his own expense.

Canada

This product complies with Class A Canadian EMC requirements.

Safety and EMC Regulatory

Australia/New Zealand

This product complies with Australia/New Zealand EMC Class A requirements.

Statements

Japan

VCCI Class A

C-8

Page 77

Korea

Taiwan

Safety and EMC Regulatory Statements

EMC Regulatory Statements

C-9

Safety and EMC Regulatory

Statements

Page 78

Safety and EMC Regulatory Statements

EMC Regulatory Statements

European Community

Safety and EMC Regulatory

Statements

C-10

Page 79

Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements

Disposal of Waste Equipment by Users in Private Household in the European Union

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Likvidace zařízení soukromými domácími uživateli v Evropské unii

Tento symbol na produktu nebo balení označuje výrobek, který nesmí být vyhozen spolu s ostatním domácím odpadem. Povinností uživatele je předat takto označený odpad na předem určené sběrné místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na příslušném obecním nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v obchodě, kde jste produkt zakoupili.

Recycle Statements

Bortskaffelse af affald fra husstande i den Europæiske Union

Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må bortskaffes med andet almindeligt husholdningsaffald. I stedet er det dit ansvar at bortskaffe kasseret udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret elektrisk og elektronisk udstyr. Den centrale modtagelse og genvinding af kasseret udstyr i forbindelse med bortskaffelsen bidrager til bevarelse af naturlige ressourcer og sikrer, at udstyret genvindes på en måde, der beskytter både mennesker og miljø. Yderligere oplysninger om, hvor du kan aflevere kasseret udstyr til genvinding, kan du få hos kommunen, den lokale genbrugsstation eller i den butik, hvor du købte produktet.

Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus

See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda. Lisateabe saamiseks selle kohta, kuhu oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma kohaliku linnakantselei, majapidamisjäätmete kõrvaldamise teenistuse või kauplusega, kust Te toote ostsite.

D-1

Page 80

Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements

Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella

Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja paikoista, joihin hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla yhteyttä jätehuoltoon tai liikkeeseen, josta tuote on ostettu.

Élimination des appareils mis au rebut par les ménages dans l'Union européenne

Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques. La collecte et le recyclage de vos appareils mis au rebut indépendamment du reste des déchets contribue à la préservation des ressources naturelles et garantit que ces appareils seront recyclés dans le respect de la santé humaine et de l'environnement. Pour obtenir plus d'informations sur les centres de collecte et de recyclage des appareils mis au rebut, veuillez contacter les autorités locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous avez acheté ce produit.

Entsorgung von Altgeräten aus privaten Haushalten in der EU

Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt nicht über den normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte abzugeben. Die getrennte Sammlung und ordnungsgemäße Entsorgung Ihrer Altgeräte trägt zur Erhaltung der natürlichen Ressourcen bei und garantiert eine Wiederverwertung, die die Gesundheit des Menschen und die Umwelt schützt. Informationen dazu, wo Sie Rücknahmestellen für Ihre Altgeräte finden, erhalten Sie bei Ihrer Stadtverwaltung, den örtlichen Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät erworben haben

Απόρριψη άχρηστου εξοπλισμού από χρήστες σε ιδιωτικά νοικοκυριά στην Ευρωπαϊκή

νωση

Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριμένο προϊόν δεν πρέπει να διατίθεται μαζί με τα άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη να απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον σε καθορισμένο σημείο συλλογής για την ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού ανακύκλωση του άχρηστου εξοπλισμού σας κατά την απόρριψη θα συμβάλει στη διατήρηση των

Recycle Statements

φυσικών πόρων και θα διασφαλίσει ότι η ανακύκλωση γίνεται με τρόπο που προστατεύει την ανθρώπινη υγεία και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά με το πού μπορείτε να παραδώσετε τον άχρηστο εξοπλισμό σας γραφείο, την τοπική υπηρεσία διάθεσης οικιακών απορριμμάτων ή το κατάστημα όπου αγοράσατε το προϊόν.

Készülékek magánháztartásban történő selejtezése az Európai Unió területén

készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából. A hulladékká vált készülékek selejtezéskori begyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, valamint biztosítja a selejtezett termékek környezetre és emberi egészségre nézve biztonságos feldolgozását.

begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat.

για ανακύκλωση, επικοινωνήστε με το αρμόδιο τοπικό

. Η ξεχωριστή συλλογή και

D-2

Page 81

Waste Electrical and Electronic Equipment (WEEE) Statements

Recycle Statements

Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea

Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche. La raccolta differenziata e il corretto riciclo delle apparecchiature da smaltire permette di proteggere la salute degli individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta delle apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio presso il quale è stato acquistato il prodotto.

Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās mājsaimniecībās

Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei.

tsevišķa nolietoto iekārtu savākšana un otrreizējā pārstrāde palīdzēs saglabāt dabas resursus un garantēs, ka šīs iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi un cilvēku veselību. Lai uzzinātu, kur nolietotās iekārtas var izmest otrreizējai pārstrādei, jāvēršas savas dzīves vietas pašvaldībā, sadzīves atkritumu savākšanas dienestā vai veikalā, kurā izstrādājums tika nopirkts.

artotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje

Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir elektroninės įrangos atliekoms perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos atliekos padės saugoti gamtinius išteklius ir užtikrinti, kad jos bus perdirbtos tokiu būdu, kuris nekenkia žmonių sveikatai ir aplinkai. Jeigu norite sužinoti daugiau apie tai, kur galima pristatyti perdirbtinas įrangos atliekas, kreipkitės į savo seniūniją, namų ūkio atliekų šalinimo tarnybą arba parduotuvę, kurioje įsigijote gaminį.

Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie

Recycle Statements

Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur. Door uw oude apparatuur apart aan te bieden en te recyclen, kunnen natuurlijke bronnen worden behouden en kan het materiaal worden hergebruikt op een manier waarmee de volksgezondheid en het milieu worden beschermd. Neem contact op met uw gemeente, het afvalinzamelingsbedrijf of de winkel waar u het product hebt gekocht voor meer informatie over inzamelingspunten waar u oude apparatuur kunt aanbieden voor recycling.

Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach domowych w Unii Europejskiej

Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i elektronicznego. Osobna zbiórka oraz recykling zużytego sprzętu pomogą w ochronie zasobów naturalnych i zapewnią ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty sprzęt do recyklingu, należy się skontaktować z urzędem miasta, zakładem gospodarki odpadami lub sklepem, w którym zakupiono produkt.

D-3

Page 82

Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements

Descarte de Lixo Elétrico na Comunidade Européia

Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem. A coleta e a reciclagem seletivas desse tipo de lixo ajudarão a conservar as reservas naturais; sendo assim, a reciclagem será feita de uma forma segura, protegendo o ambiente e a saúde das pessoas. Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido.

Likvidácia vyradených zariadení v domácnostiach v Európskej únii

Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je určené na recykláciu vyradených elektrických a elektronických zariadení. Separovaný zber a recyklácia vyradených zariadení prispieva k ochrane prírodných zdrojov a zabezpečuje, že recyklácia sa vykonáva spôsobom chrániacim ľudské zdravie a životné prostredie. Informácie o zberných miestach na recykláciu vyradených zariadení vám poskytne miestne zastupiteľstvo, spoločnosť zabezpečujúca odvoz domového odpadu alebo obchod, v ktorom ste si výrobok zakúpili.

Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji

Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv način. Za podrobnejše informacije o tem, kam lahko odpeljete odsluženo opremo na recikliranje, se obrnite na pristojni organ, komunalno službo ali trgovino, kjer ste izdelek kupili.

Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea

Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos. La recogida y el reciclado selectivos de los residuos de aparatos eléctricos en el momento de su eliminación contribuirá a conservar los recursos naturales y a garantizar el reciclado de estos residuos de forma que se proteja el medio ambiente y la salud. Para obtener más información sobre los puntos de recogida de residuos eléctricos y electrónicos para reciclado, póngase en contacto con su ayuntamiento, con el servicio de

Recycle Statements

eliminación de residuos domésticos o con el establecimiento en el que adquirió el producto.

Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen

Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter. Separat insamling och återvinning av avfallet hjälper till att spara på våra naturresurser och gör att avfallet återvinns på ett sätt som skyddar människors hälsa och miljön. Kontakta ditt lokala kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du köpte produkten för att få mer information om var du kan lämna ditt avfall för återvinning.

D-4

Page 83

Index

Numerics

10/100/1000Base-TX ports

location on switch … 1-2

1000Base-LH

connections, length limitations … 2-6 ports, cables used with … 2-6, B-2

1000Base-LX

connections, length limitations … 2-6 ports, cables used with … 2-6, B-2

1000Base-SX

connections, length limitations … 2-6 ports, cables used with … 2-6, B-2

1000Base-T

connections, length limitations … 2-5 ports, cables used with … 2-5

AC power connector

location on back of switch … 1-6 Act LED … 1-4 act LED … 1-4 auto MDI/MDI-X operation … B-6

MDIX feature … B-5

back of switch

description … 1-6

power connector … 1-6 backbone switch

topology with … 2-22 basic switch configuration

IP address … 3-3

manager password … 3-2

subnet mask … 3-3

Switch Setup screen … 3-2 basic troubleshooting tips … 4-1 blinking LEDs

error indications … 4-4 Bootp

automatic switch configuration … 3-2

for in-band access … 2-17

buttons

Clear button … 1-5 LED Mode select button … 1-4 Reset button … 1-5

cabinet

mounting the switch in … 2-11

cables

1000Base-LH

connections … 2-6 fiber-optic cable specifications … B-2

1000Base-LX

connections … 2-6 fiber-optic cable specifications … B-2

1000Base-SX

connections … 2-6

fiber-optic cable specifications … B-2 1000Base-T connections … 2-5 connecting cables to switch ports … 2-16 effects of non-standard cables … 4-2 fiber-optic, specifications … B-2 infrastructure requirements … 2-5 length limitations … 2-5 required types … 2-5 serial, for direct console connection … 2-18

cables, twisted pair

category 3, 4, 5 … B-5 cross-over cable pin-out … B-7 MDI-X to MDI connections … B-6 MDI-X to MDI-X connections … B-7 pin-outs … B-6 straight-through cable pin-out … B-6 switch-to-computer connection … B-6 switch-to-switch or hub connection … B-7

cables, twisted-pair

MDIX feature … B-5 wiring rules … B-5

cables, twisted-pair connector pin-outs … B-5 cabling infrastructure … 2-5

Index

Index – 1

Page 84

Index

Clear button

deleting passwords … 1-5 description … 1-5 location on switch … 1-2, 1-5 restoring factory default configuration … 1-5,

4-11

to delete password protection … 3-4

CLI prompt, console

displaying … 2-18

configuration

checking when troubleshooting … 4-3 DHCP/Bootp … 3-2 full duplex only for mini-GBICs … 2-7 IP address … 3-3 IP address, manually … 3-2 manager password … 3-2 restoring factory defaults … 1-5, 4-11 subnet mask … 3-3

Switch Setup screen … 3-2 connecting the switch to a power source … 2-15 connector specifications … A-2 console

checking messages during

troubleshooting … 4-9 displaying the CLI prompt … 2-18 features … 2-17 how to connect in-band … 2-17 how to connect out-of-band … 2-17 serial cable connection … 2-18 Switch Setup screen … 3-2 Telnet access … 3-5 terminal configuration … 2-17

console port

location on switch … 1-2

cross-over cable

pin-out … B-7

deleting passwords … 1-5 description

back of switch … 1-6 front of switch … 1-2 LEDs … 1-3 switch … 1-1

desktop switch

sample topology … 2-19

DHCP

automatic switch configuration … 3-2 for in-band access … 2-17

diagnostic tests … 4-9

checking the console messages … 4-9 checking the LEDs … 4-9 end-to-end connectivity … 4-10 testing the switch only … 4-9

testing twisted-pair cabling … 4-10 downloading new switch software … 4-12 dual-personality ports

location on switch … 1-2

operation description … 1-2

electrical specifications, switch … A-1 EMC regulatory statements … C-8 environmental specifications, switch … A-1

factory default configuration, restoring … 4-11 factory default configuration,restoring … 1-5 Fault LED … 1-3

behavior during self test … 2-10

behaviors … 1-3

blinking definition … 1-4

location on switch … 1-2

showing error conditions … 4-4 FDx LED … 1-4–1-5 features

console … 2-17

switch … 1-7 fiber-optic cables … B-2

1000Base-LH … B-2

1000Base-LX … B-2

1000Base-SX … B-2 front of switch … 1-2

10/100/1000Base-TX ports … 1-2

Clear button … 1-5

description … 1-2

dual-personality ports … 1-2

LED Mode select button and LEDs … 1-4

LEDs … 1-3

network ports … 1-2

Reset button … 1-5

2 – Index

Page 85

full-duplex fixed configuration

effects on network connections … 4-1

full-duplex operation of mini-GBICs … 2-7

horizontal surface

mounting switch on … 2-14

in-band … 3-1 in-band console access

types of … 2-17 included parts … 2-1 installation

connecting the switch to a power source … 2-15

horizontal surface mounting … 2-14

location considerations … 2-6

network cable requirements … 2-5

precautions … 2-4

rack or cabinet mounting … 2-11

site preparation … 2-5

summary of steps … 2-3

wall mounting … 2-15 IP address

configuring … 3-3

LED Mode

indicator LEDs … 1-4

select button … 1-4

selecting the display … 1-4 LEDs

Act … 1-4

act … 1-4

behavior during self test … 2-10

blinking definition … 1-4

checking during troubleshooting … 4-9

descriptions of … 1-3

error indications … 4-4

Fault … 1-3

behavior during self test … 2-10

showing error conditions … 4-4 FDx … 1-4–1-5 LED Mode View select indicators … 1-4 Link … 1-3 link … 1-4 location on switch … 1-2 Mode

selecting the display … 1-4 on switch … 1-3 port

description … 1-3 Power … 1-3

behavior during self test … 2-10 Self Test … 1-3

behavior during self test … 2-10 Spd … 1-4–1-5

length limitations

1000Base-LH connections … 2-6 1000Base-LX connections … 2-6 1000Base-SX connections … 2-6 1000Base-T connections … 2-5

link LED … 1-4 Link LEDs … 1-3 link test … 4-10 location for the switch, considerations … 2-6

MDIX

feature description … B-5

MDI-X to MDI network cable … B-6 MDI-X to MDI-X network cable … B-7 mini-GBICs

full-duplex operation … 2-7 slot, location on switch … 1-2

mounting the switch

in a rack or cabinet … 2-11

precautions … 2-4 on a horizontal surface … 2-14 on a wall … 2-15

Index

Index – 3

Page 86

network cables

1000Base-LH connections … 2-6 1000Base-LX connections … 2-6 1000Base-SX connections … 2-6 1000Base-T connections … 2-5 fiber-optic, specifications … B-2 MDIX feature … B-5 required types … 2-5 twisted-pair connector pin-outs … B-5 twisted-pair, wiring rules … B-5

network devices

connecting to the switch … 2-16

network ports

connecting to … 2-16 location on switch … 1-2 standards compliance … A-2 types of … 1-2, 2-5

non-standard network cables, effects … 4-2

ports

10/100/1000Base-TX, location on switch … 1-2 connecting to … 2-16 console … 2-17 MDIX feature … B-5 network connections … 2-16

power connector … 1-6 Power LED … 1-3

behavior during self test … 2-10 behaviors … 1-3 location on switch … 1-2

power source

connecting the switch to … 2-15

precautions

mounting the switch … 2-4 power requirements … 2-4

preparing the installation site … 2-5 Proactive Network tools

diagnostics with … 4-8

Index

out-of-band console access … 3-5

parts, included with the switch … 2-1 password

configuring … 3-2

passwords

deleting with the Clear button … 3-4

if you lose the password … 3-4 passwords,deleting … 1-5 physical specifications, switch … A-1 Ping test … 4-10 pin-outs

twisted-pair cables … B-5 port configuration

checking when troubleshooting … 4-3 port LEDs

description … 1-3

Link … 1-3

normal operation … 2-10

rack

mounting precautions … 2-4

mounting the switch in … 2-11 recycle statements … D-1 regulatory statements … C-8 Reset button

description … 1-5

location on switch … 1-2, 1-5

restoring factory default configuration … 4-11 resetting the switch

factory default reset … 4-11

location of Reset button … 1-5

troubleshooting procedure … 4-9

safety and regulatory statements … C-1 safety specifications … A-2 segment switch

sample topology … 2-20 selecting the LED Mode display … 1-4

4 – Index

Page 87

self test

Fault LED behavior … 2-10 LED behavior during … 2-10 Power LED behavior … 2-10

serial cable

for direct console connection … 2-18

slots for mini-GBICs

location on switch … 1-2 Spd LED … 1-4–1-5 specifications

connectors … A-2

electrical … A-1

environmental … A-1

physical … A-1

safety … A-2 straight-through cable

pin-out … B-6 subnet mask

configuring … 3-3 summary

of cables used with the switch … 2-5

of switch installation … 2-3 switch

connecting to a power source … 2-15

description … 1-1

downloading new software … 4-12

electrical specifications … A-1

environmental specifications … A-1

features … 1-7

front panel description … 1-2

included parts … 2-1

LED descriptions … 1-3

mounting in a rack or cabinet … 2-11

mounting on a wall … 2-15

mounting on horizontal surface … 2-14

physical specifications … A-1 switch operation

verifying after installation … 2-9 Switch Setup screen … 3-2

configuring a subnet mask … 3-3

configuring an IP address … 3-3

field descriptions … 3-3

Telnet access to the console … 3-5 terminal configuration … 2-17 Test LED … 1-3

behavior during factory default reset … 4-11 behavior during self test … 2-10

testing

checking the console messages … 4-9 checking the LEDs … 4-9 diagnostic tests … 4-9 end-to-end communications … 4-10 link test … 4-10 Ping test … 4-10 switch operation … 4-9 switch-to-device communications … 4-10

twisted-pair cabling … 4-10 tips for troubleshooting … 4-1 topologies

samples of … 2-19 troubleshooting … 4-1

basic tips … 4-1

checking port configuration … 4-3

checking the console messages … 4-9

checking the LEDs … 4-9

common network problems … 4-1

connecting to fixed full-duplex devices … 4-1

diagnostic tests … 4-9

effects of non-standard cables … 4-2

link test … 4-10

Ping test … 4-10

Proactive Network tools … 4-8

restoring factory default configuration … 4-11

testing connections to other devices … 4-10

testing end-to-end communications … 4-10

testing the switch … 4-9

testing the twisted-pair cables … 4-10 twisted-pair cable

cross-over cable pin-out … B-7

pin-outs … B-5–B-6

straight-through cable pin-out … B-6

switch-to-computer connection … B-6

switch-to-switch or hub connection … B-7

testing … 4-10 twisted-pair ports

MDIX feature … B-5

Index

Index – 5

Page 88

VT-100 terminal

serial cable connection for … 2-18

wall

mounting the switch on … 2-15

waste electrical and electronic equipment

statements … D-1

wiring rules for twisted-pair cables … B-5

Index

6 – Index

Page 89

Page 90

Technical information in this document is subject to change without notice.

Printed in Taiwan July 2006

Manual Part Number

5991-3833

*5991-3833*

HP 2510-24 Installation And Getting Started Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

Introducing the Switch

Front of the Switch

Console port

Network Ports

LEDs

LED Mode Select Button and Indicator LEDs

Reset Button

Clear Button

Back of the Switch

Power Connector

Switch Features

Installing the Switch

Included Parts

Installation Procedures

Summary

Installation Precautions:

1. Prepare the Installation Site

2. Installing or Removing mini-GBICs

3. Verify the Switch Passes Self Test

LED Behavior:

4. Mount the Switch

Rack or Cabinet Mounting

Rack Mounting the Switch 2510-24

Horizontal Surface Mounting

Wall Mounting

5. Connect the Switch to a Power Source

6. Connect the Network Cables

Using the RJ-45 Connectors

Connecting Cables to mini-GBICs

7. (Optional) Connect a Console to the Switch

Terminal Configuration

Direct Console Access

Sample Network Topologies

As a Desktop Switch

As a Segment Switch

Connecting to a Backbone Switch

Stacking the Switch

Configuring the Switch

Recommended Minimal Configuration

Using the Console Setup Screen

Where to Go From Here

Using the IP Address for Remote Switch Management

Starting a Telnet Session

Starting a Web Browser Session

Troubleshooting

Basic Troubleshooting Tips

Diagnosing with the LEDs

Proactive Networking

Hardware Diagnostic Tests

Testing the Switch by Resetting It

Checking the Switch LEDs

Checking Console Messages

Testing Twisted-Pair Cabling

Testing Switch-to-Device Network Communications

Testing End-to-End Network Communications

Restoring the Factory Default Configuration

Downloading New Switch Software

ProCurve Customer Support Services

Before Calling Support

Physical

Electrical

Environmental

Connectors

Safety

Lasers

Switch Ports

Twi sted -Pair Cab les

Mode Conditioning Patch Cord for Gigabit-LX

Installing the Patch Cord

Twisted-Pair Cable/Connector Pin-Outs

Straight-Through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections

Cable Diagram

Pin Assignments

Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection

Cable Diagram